Providing Fire Fighting System-OP Block General Hospital Pala

Amount

DIESEL ENGINE DRIVEN PUMP:- Supply Installation, testing and commissioning of Main Diesel Engine driven pump of centrifugal end suction type suitable for automatic operation rated for 2280 LPM at 60m head at 38HP high efficiency volute type with cast iron casing, Bronze impeller Pump coupled to a diesel engine at 1800 RPM including supply of all accessories such as common base plate suitable foundation for engine and pump, vibration damping arrangements, Battery, coolant, lubricating oil, exhaust piping, necessary controls such as pressure switch and interconnecting cable from control panel to Battery etc.

MAIN FIRE PUMP:- Supply Installation, testing and commissioning of Fire fighting Main pump electrical motor driven type rated for 2280 LPM at 60m head high efficiency volute type with cast iron casing, Bronze impeller Pump coupled to a squirrel cage induction motor SPDP including supply of all accessories with supply condiion 415V,50Hz, 3 phase floor mounted type rated for 40HP and 2900 RPM including supply of all accessories such as coupling, vibration damping arrangements, coupling guard base frame foundation bolt etc.

JOCKEY PUMP - SITC of electrical motor driven fire pump capable of delivering 180 LPM 60m head with cast iron body bronze impeller coupled with supply condition 415V, 3 phase 50Hz, foot mounted type rated for 10HP including common base plate coupling guard and all other accessories.

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Fabrication, supply, conveyance and installation of base frame for floor mounting type panel board using channel of class designation ISMC 75 including cutting, welding, drilling holes, painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel and to the finished floor using required bolt and nuts, making good the damages etc. as required.

Supply and providing 2mm thick of SMC sheets in the panel as barriers & shrouding using required bolts and nuts including cutting to shape etc., as required.

Supply and fixing "A" section neoprene beeding suitasble for 1.60/2.00 mm sheet along the periphery of doors/other detachable compartments to make the panel assembly dust & vermin proof including stricking with glue

Fabrication, supply & fixing main bus bar system and interconnections with electrolytic grade copper strips/ rigid conductors conforming to IS 1867 (with latest amendments) for bus bar arrangement with single strip per phase supported on finger type bus bar supports of adequate size, spacing between supports not exceeding 50 cm & overhang not exceeding 5 cm including bending to shape, drilling holes, tinning the points of contacts, fixing heat shrinkable PVC sleeves, plated bolts and nuts with plate washers and spring washers, copper sockets for round conductors, etc., as required.

Fabrication, supply & fixing earth bus system with copper strip/ conductor and connecting all accessories as per rule including g tinning the points of contacts etc as required

LED indicators for all voltage ranges - Red, Green, Black, Yellow or Orange Colour

Aluminium anidised Danger Notice Board of size 200 x 150 mm, with inscriptions (both in English and Malayalam) and conventional Skull and Bone in Red colour

Carrying out control wiring for panel with normal meters and indication lamps alone with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/equipments including providing suitbable size insulated sockets at the termination points or soldered properly, providing numbering ferrules for the proper identification of the wiring, keepi ng the wiring firm by suitable tie/tie mounts/PVC duct etc as required. 1.50 sq mm single run with required sockets.

Supply and fixing 20 A fuse holder for BS type blade fuses (Group B) with 2A cylindrical type fuse links (Group B) fuse in the existing meter board and giving connections etc.

Incoming :S & F 200A, 4 pole Isolation duty type MCCB

Outgoing :S & F 100A, 4 pole Isolation duty type MCCB

Outgoing :S & F 63A, 4 pole Isolation duty type MCCB

Power contactor 100A 3pole

Power contactor 63A 3 pole

Indication Lamp

Battery Charging Unit

DC Hooter

12/24V DC relay

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 core 6 sq mm with factory made clamp

3 core 35 sq mm with factory made clamp

3.5 core 95 sq mm with factory made clamp

Supplying siemens / tropodur type nickel plated single compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for 2/ 3/ 3½/ 4 core cable of the following sizes as required. 6 sq mm

Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required. 4 sq mm with 12 mm wide x 1 mm thick clip

25 sq mm with 20 mm wide x 1.20 mm thick clip

Supply of superior quality aluminium tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required. 4 sq.mm

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 3.15 mm copper conductor (10 SWG)

4.00 mm copper conductor (8 SWG)

Above Ground / Under Ground Piping:- Supply, and commissioning of M.S 'C' class pipes confirming to IS:1239 part I with malleable specials confirming to IS.1239 part.II, such as elbows, reducers, flanges etc. including cutting, welding, fixing in/on walls/ceiling by suitable, supports. The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour/shade. 100 mm dia

80 mm dia

65 mm dia

50 mm dia

40mm dia

32mm dia

25mm dia

Air Cussion Vessel:- Supply Installation, Testing and Commissioning of Air cushion Vessel M.S. of 100 mm Dia with automatic air release cock, 25 mm Dia, drain valve and a shut off and 120 cm in height.

Priming Tank:- Supply and erection of PVC priming tank of 1000 liters of effective storage capacity

Butterfly valve - Supplying, installing, testing and commissioning CI Butterfly valve slim seal standard lever operated, wafer type, SG iron coated with nylon Disk, SS shaft, Nitrile Body lining . PN 16 rating. Design as per BS 51 confirming IS 13039 with required flanges nuts, bolts. 100 mm dia

80mm dia.

50 mm dia

Non return valve-Supply, installation, testing and commissioning of C.I. slim seal type Non return valve with required flanges, nuts and bolts gasket etc. complete 100 mm dia

80mm dia.

Ball valve - Supply erection and commissioning of Ball valve 25mm dia

32mm dia

Foot valve - Supply and installation of the following sizes of cast iron Foot valve with strainer to the pump sets complete with bolts, nut gaskets if any as required etc. 100mm dia

Air release valve - Supply, installation, testing and commissioning of single acting Air Release Valve with screwed inlet 32mm dia etc.

Branch pipe-Supply installation and commissioning of beanch pipe (GM)with threaded outlets 15 mm nozzle IS 903

Supply Installation, Testing and Commissioning of Fire brigade Inlet 2 Way with all accessories

Hydrant valve - Supply, installation, testing and commissioning of instances pattern stain less steel single Headed Hydrant valve bearing to IS:5290,63mm oblique type with instantaneous hose coupling adaptor, complete with PVC blank cap

Supply and place in position of Controlled percolated Hose conforming to IS 623,63mm 15 Mts. Long ,with male and female instantaneous SS coupling

Hose Cabinet single

Supply, installation, testing and commissioning of Hydraulic, Hose Rest drum completed with swinging type drum with 19mm dia Rubber braided hose of 30M length and Shunt off nozzle, with necessary fittings etc. Complete

Supply, installation, testing and commissioning of approved make 15mm brass sprinkler heads designed to operate at 68 deg.. Celsius etc. with necessary fitting etc. Complete. Pendent type

Side wall type.

PRESSURE SWITCH:- Supply Installation, Testing and Commissioning of pressure switch bellow type of approved make.

PRESSURE GAUGE:- Supply Installation, Testing and Commissioning of pressure gauge with 0 to 200 PSI

Supplying, installing, testing and commissioning of microprocessor based main fire alarm control panel of 12 Zones with visual LCD indications for fire/fault alarms, signals and should have stage alarm facility with maintenance free battery back up for 24 hours normal operation and 15 minute alarm operation. The panel shall be fabricated by MS sheet and powder coated both inside and out side door shall be glass fronted type with locking arrangement as per specification.

Supplying, installing, testing and commissioning of optical type smoke detectors with solid stage design, indicating lamp, mounting base etc Addressable type.

Supplying, installing, testing and commissioning of optical type heat detectors with solid stage design, indicating lamp, mounting base etc. Addressable type

Supplying, installing, testing and commissioning of response indicator with solid stage design, indicating lamp, mounting base etc. Addressable type

Supplying, installing, testing and commissioning of Manual call point break glass type as per standard specification.

Supplying, installing, testing and commissioning of Electronic dual tone Hooter (sounder) addressable type specification.

Supply, laying and clamping of FRLS PVC insulated and PVC sheathed armoured power cable, 1.1 KV grade of the following sizes, spacing of clamps not exceeding 60cms, making good the damages, colour washing etc. as required. 2 core 1.50 sq mm copper using factory made saddles

Supply and providing 5Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

Supply and fixing 2 k.g CO2 type Fire Extinguisher with hose and clamps including fixing it to wall as required.

Supply and Fixing 6 zone talk back control console & controller unit with call switch - innovative make

Supply and Fixing Gooseneck Micro phone ( fitted to console)-Innovative make

Supply and Fixing 90 watts mixer Amplifier

Supply and Fixing Two way talk back Speaker with call switch ( Innovative make)

Supply and Fixing of auto gluing Fire Signage Board with inscriptions ( both in English and Malayalam) . 300x200 mm size

Supply and Fixing of fire Emergency Light having 2 nos Lamp, 7 AH SMF Battery, Charger, controller, EXIT display etc

Supply & erection of Assembly Point sign board 16" x 16"

Supply & erection of Fire Escape rout in each floor having size 12" x 16" made of 3mm thisk acrylic sheet with glass frame

Charges for preparation of Fire Drawing per A3 sheet first copy

Copying charges for additional copies per A3 sheet

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on surface including making good the damages etc as required. 20 mm dia light gauge

Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 1.00 sq mm 2 run

1.00 sq mm 4 run