Spl repair to Bldg No P-118 at Talwar Line Fafa Accn , security fencing 400 mtr near bindal pump house and certain Minor works under GE Dehradun.

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Material and labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 , using old size bricks, complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (using old size bricks) complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:6, surface finished even and smooth (without using extra cement) complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, surface finished even and smooth (without using extra cement) complete all as specified and directed. (WPC will be measured and paid separately).

Material and labour for 10 mm thick rendering on celing surface in cement mortar 1:3 mixed surface finished even and smooth including fixing of wire mesh wherever required complete all as specified and directed.

Material and labour for preparation of newly plastered surface of walls including corners and applying two coats of distemper oil emulsion over applying of 1-2 mm thick wall care putty finish wall surface even & smooth all as specified and directed.

Surface excavation of any type of soil n.exc 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Square metre on plan and n exc 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and as directed.

Material and labour for cement concrete 1:2:4 type B0 (using 12.5 graded stone aggregate) 40mm thick in Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

Supply & fix 2-3mm Acrylic sheet as in view cutter etc. complete all as specified and directed. (Mild steel frame will be measured separately and paid accordingly)

Material and labour for complete removal of existing treatment of walls including corners and applying two coats of distemper oil emulsion with roller over applying of 1-1.5 mm thick wall care putty finish wall surface even & smooth all as specified and directed.

Material and labour for two coats of exterior grade 1st quality weather coat paints over a coat of alkali resistant priming paint over applying of 1-1.5 mm thick wall care putty finish wall surface even and smooth including preparation of new plaster external surfaces of wall etc complete all as specified and directed.

Material and labour for complete removal of existing treatment of walls including corners and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Square metre over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Square metre over applying of 1-2 mm thick wall care putty finish wall surface even and smooth complete all as specified and directed.

Material and labour for preparation of newly plastered surface on ceilings and applying three coats of white wash on ceiling, off sets, pillar etc. complete all as specified and directed.

Material and labour for complete removal of existing treatment on ceiling and applying three coats of white wash on ceiling, off sets, pillar etc all as directed and specified.

Material and labour for Preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and as directed.

Material and labour for complete removal of existing treatment of walls and applying three coats of white wash on walls complete all as specified and as directed.

Writing letters or figures (Block. Roman, Italic or Indian) nexc 30 cm high Writing bldg No complete all as specified and directed by Engr-in-Charge.

Material and labour applying two coats of Synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

Material and labour applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

Material and labour for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm width or girth & complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying one coat of Synthetic enamel paint on old wooden surfaces of any description over 10 cm width or girth complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying one coat of Synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

Material and labour for non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x 6-7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

All as per item No 26 here in before but as in skirting and including 10 mm thick rendering in cement mortar 1:4, complete all as directed and specified.

Material and labour for non skid/mat finish ceramic colour tiles of size 300 mm x 300 mm and 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for coloured joint free non-skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Square metre but not exceeding 0.18 Square metre, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified.

Material and labour glazed ceramic colour tiles size 300 mm x 450 mm/ 300 mm x 600mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as directed and specified.

Material and labour for coloured ceramic tiles in vertical surface 300 x 450 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM (1:4) complete all as specified.

Material and labour for 60 mm thick pre polished rubber moulded Yellow/ Red colour machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and as directed by the Engr-in-Charge.

Dismantling of stone slabs and tiles laid, bedded in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Material and labour for 18-20 mm thick Granite, of any type, table rubbed and polished in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified including moulding complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.50 Square metre with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames exc 1.50 Square metre but n.exc 4.00 Square metre with shutters (without taking off shutters from the frames) complete all as specified and directed.

Supply and fix factory made 100 % solid wood plastic composite (WPC) door frame 125x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cubic metre from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing complete all as specified and directed by Engr-in-Charge.

Supply and fix 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side plain with density not less than 600 Kg/Cubic metre. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and directed by Engr-in-Charge.

Supply and fix 30 mm thick moulded WPC factory made Glazed and skeleton shutter (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side plain with density not less than 600 Kg/Cubic metre. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and directed by Engr-in-Charge.

Supply and fix Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified (Note: framed filled in cement concrete1:2:4 type B0 ( 12.5 mm stone aggregate)

Supply and fix 30mm thick flush shutters, solid core construction, designer with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

Supply and fix prelaminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges will be painted to match with prelam sheet, PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gab insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as shown in SSR Part-II and as directed by Engineer in Charge.

Supply and fix MS Butt Hinges medium weight, cold rolled mild steel 100 mm fixed to steel/wooden shutters complete all as specified and directed.

Supply and fixing Butt hinges 100 mm size medium weight cold rolled stainless steel and fixed complete all as specified and as directed by Engr-in-Charge.

Supply and fix for mild steel barrel tower bolts 150 mm size, stove enamelled black, with bright bolt fixed in repairs complete all as specified and directed.

Supply and fix 150 mm size solid in one piece stainless steel handles, cast D type, fixed in stainless steel screws complete all as specified and directed by Engr-in-Charge.

Supply and fix 300 mm long MS Helical door spring welded to steel frame or fixed to wooden door frame with screws including roller and roller plate etc complete all as specified and directed.

Supply and fix floor door stopper of stainless steel double legged and tongue, 304 grade, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

Supply and fix stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and directed.

Supply & fixing of Elixir 2000 Series Windows (chocolate brown) made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length metre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/ masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete all as specified and directed by Engr-in-Charge.

Supply and fix factory made steel ventilator with top hung shutters including hinges with steel handle, steel peg stay, tower bolt etc.complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply and fix steel work in tubular section for stair case, railing at balconies, roof truss etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-179 grade St-240 complete all as specified and directed.

Supply and fix Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W(Gde E-250) quality-A all as specified and directed

Supply and fix 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

Supply and fix Stainless steel 304 grade wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with 8% nickle complete all as specified and directed.

Supply and fix in repair WPC board 18-19 mm thick, one side prelamiated, 600 density, flat pressed, single layer type or three layer type, BWR grade in any position complete all as specified and directed.

Supply and fix in repair PVC board 18-19 mm thick, medium density, flat pressed, single layer type or three layer type, BWR grade in any position complete all as specified and directed.

Supply and fix in repair PVC board 4-5 mm thick fixed with screw and washer in cupboards etc complete all as specified and as directed .

Supply and fix Continuous (Piano) hinges, mild steel, bright finished or stainless steel 304 grade, width of flaps (When open) 30 mm complete all as specified and directed.

Supply and fix magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

Supply and fix in repair 25 mm dia stainless steel polished 204 grade drapery rod 1mm thick with final decorative, including brackets, decorative finished at both ends complete all as speccified and directed as per approved sample complete all as specified and directed.

Supply and fix medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing including dismantling of old tubing complete all as specified and directed.

Supply and fix medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing including dismantling of old tubing complete all as specified and directed.

Material & labour for demolition of existing sunken portion & taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish off the premises, cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00 Kilogram/Square metre and grouting 25mm thick cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (b) Material & labour for two coat of acrylic cementitious water proofing coating (Dr. FIXIT pidifin 2K manufactured by M/S Piditite Industries Ltd or equivalant) and followed by a overlay protective screed 15mm thick CM(1:3) alongwith liquid water proofing compound approved make on top surfaces of sunken slab after preparation as mentioned above method of application for acrylic cementitious water proofing coating is followed as per manufacturers instructions complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repair vitreous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap (SI 3989 1984), set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge.

Supply and fixing 10 litres capacity PVC low level valve less symphonic action type flushing cistern white with inlet, float valve, float and handle including brackets with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repair vitreous china corner wash hand basin including brackets, white size 550 x 400 mm including cutting for and pinning in ends of brackets, including Waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed.

Supply and fixing in repairs vitreous china wash down water closet EWC white (excluding flushing cistern and flush pipe) with CI 'P' or 'S'; trap including plastic white seat cover, CP Jet spray with 1.0 mtr long PVC pipe, connecting to stack pipe and to flushing pipe and complete including making good to floor complete all specified and directed.

Supply and fix in repair pillar taps, swan neck type, 15mm bore cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed complete all as specified and directed.

Supply and fix CP brass bib tap 15mm bore screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix in repairs CP stop/angle cock fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

Supply and fixing brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule complete all as specified and directed.

Supply and fix in repair CP brass shower rose 15mm dia,100mm dia complete all as specified and directed.

Supply and fix in repairs PVC connection 15mm size with PTMT nuts, of 450 mm long complete all as specified and directed.

Supply only PVC connection 15 mm dia 450 to 600 mm long with brass fly nut at both ends complete all as specified and directed.

Supply and fix in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed by Engr-in-Charge.

Supply and fixing brass chromium plated towel rail, 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

Supply and fix in repairs Soap dish 6 inches, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Supply and fixing Chromium Plated brass soap dish fixed to wall with chromium plated brass screwed and cup washer complete all as specified and directed.

Supply and fix in repair sink/waste coupling 32mm dia PTMT half or full threaded complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair CP steel Grating round with steel frame with hinge 100mm dia all complete all as specified and directed by Engr-in-Charge.

Supply and fix in repairs 32mm bore heavy duty waste pipe not less than 60cm long with PVC coupler for kitchen sink, WHB, urinal, etc complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair plate rack 300mm and size 100 x 80 cm made out of 1.00 mm thick stainless steel complete all as specified and as directed.

Supply and fix in repairs stainless steel kitchen sinks without draining board ISI marked made of stainless steel 1 mm thick, with plugs, washers and wastes, including bedding lime cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 410mm x 330mm x 160mm, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified & directed.

Material and labour for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like including demolition of old RCC, complete all as specified and directed.

Material and labour for use waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, chajja and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

Material and labour for TMT MS bar 8 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

Taking down CI/AC/PVC pipes incl fittings upto 110mm dia and removing from site complete all as specified and directed.

Supply and fix PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls or laid in trenches or floors complete all as specified and directed.

Supply and fix PVC (SWR) pipes of 75 mm dia, single socketed fixed to walls or laid in trenches or floors complete all as specified and directed.

Supply and fix PVC (SWR) bends of 110 mm dia, any radius complete all as specified and directed.

Supply and fix PVC (SWR) bends of 75 mm dia, any radius complete all as specified and directed.

Supply and fix PVC (SWR) junction single Tee equal or unequal 110 mm dia complete all as specified and directed.

Supply and fix PVC (SWR) junction single Tee equal or unequal 75 mm dia complete all as specified and directed.

Supply and fix PVC nahani trap of 75mm bore, with grating including jointing to waste pipe with solvent fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

Material and labour PVC (SWR) floor trap plain with grating including jointing with solvent cement 75 mm bore outlet complete all as specified and directed.

Supply and fix in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed.

Supply and fix in repairs for 110mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed by Engr-in-Charge.

Material and labour for 75mm thick PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement and demolition of existing old cement concrete of plinth protection in ground floor and paving below or above ground level complete all as specified and directed.

Material and labour for Red/ yellow colour pre-polished rubber moulded chequred cement concrete tile 300mm x 300mm x 20-22mm thick with anti skid properties set, jointed and pointed in neat cement slurry as in floor with grey cement and pigment laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Supply and fix rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external and internal white and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed.

Supply and fix in repairs Gun metal gate valve iron wheel head screwed both ends for iron pipe of 20 mm bore complete all as specified and directed.

Supply and fixing 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Taking out & removing existing roof treatment of any description completely upto concrete surface including racking out joints, hacking for key,sweeping clean and scrubbing down with water etc to remove dust etc,complete all as specified..

Material & labour for surface preparation of roof and treating of joints, filling of honey combs and providing 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) with WPC over roof surface complete all as specified and directed. (WPC shall be measured and paid separately).

Supply only integral water proofing compound as per manufacturers instructions complete all as specified and directed.

Material and labour for Water proofing roof treatment with Polymeric water proofing membranes of weight not less than 3Kg/Square metre five layers with center core as 90 micron high molesuvre,high density polythene film sand witched between two layers of polymeric (Static polythene based) between laminated on both sides with 20 micron HMDPF film over a coat of hot blown bitumen with 85/25 grade @ 1.20 Kg/Square metre after priming the surface with bituminous emulsion @ 0.30 Litre/Square metre on plastered surface. Water proofing membrane should be laid with over laps 150 mm at ends and 75 mm for sides and shall be bounded uniformity by LPG torch flame over the polymeric water proofing membranes apply semi hot blown bitumen 85/25 grade @ 1.20 Kg/ Square metre dusted sand over the coat of the coat @0.5 Kg/Square metre and applying aluminium reflective paint over it complete all as specified and as per manufacturers instructions

Cleaning of roof slab, chajja, including picking sweeping cleaning and washing with water to remove dust including taking down of exsiting roof treatment and providing water proofing treatment under:- (a) Applying a coat of STAR PROOF MB-602 with help of brushes on the cleaning RCC slab/Chajja. (b) Laying a layer of fiber cloth on wet MB-602 coating and applying another cost of MB-602. (c) After drying of surface finaly applying a coat of STAR PROOF SP-600 of any colour as per manufacturers instruction. NOTE:- The work of above water proofing treatment shall be got executed as per manufacture instructions through expert team or authorised applicator of manufacturing MS STAR SS PL Make:- APURVA INDIA/ STP/ apply treatment by using DAMPGUARD treatment of Dr Fixit as per manufacturer instructions and approved by GE.

Supply and fix in repair factory made RCC manhole cover of size 450x1200 mm and thickness 50mm and including removal of old unserviceable covers from site complete all as specfied and directed by Engr-in-charge. Make: Tulip/Sagar tiles

Material and labour for cement concrete 1:2:4 type B-2 (40 mm graded aggregate ) as in surface channel and drain complete all as specified and directed by Engr-in-Charge.

Material and labour for extra forming fair finished drain or channel 45 cm inner grith in cement concrete using extra cement , including formwork, moulds, mitred/stopped ends etc complete all as specified and directed by Engr-in-Charge.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 Cubic metre, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Material and labour for cement concrete type C2 1:3:6 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed.

Supply and fix for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; mild steel framework; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and fix 5 to 10 mm mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, nexc 15cm long complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth including two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof coverings complete all as specified and directed.

Supply and fix for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an ecofriedly colour having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

Supply and fix in repair for Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75mm spacings and straining (as in linear or concertina form) and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Supply only Chainlink MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

Material and labour for Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for TMT MS bar 10mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia complete all as specified and directed.

Material and labour for preparation of new surfaces of walls and applying two coats of cement base paint over suitable primer complete all as specified and as directed.

Material and labour for complete removal of existing treatment of walls and applying two coats of cement base paint over applying of 1-1.5 mm thick wall care putty complete all as specified and as directed.

Dismantling timber scantlings of framed work 40 Sq. cm and over in section, in any position complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness incl cover fillets complete all as specified and directed.

Material and labour for providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grams, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and cross 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, complete all as specified and directed.

Material and labour for broken stone or boulders hardcore of gauge nexc. 63 mm, deposited, spread and levelled in layers nexc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and labour for hardcore of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces in broken stone or boulder complete all as specified and as directed.

Material and labour 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in sub base complete all as specified and as directed by the Engr-in-Charge.

Material and labour for sand filling 25mm thick under floors or in foundations including watering and consolidation complete all as specified and as directed.

Material and labour for cement concrete type B-1 1:2:4 (20 mm graded stone aggregate) 25 mm thick as in floor finished even and smooth complete all as specified and as directed .

Supply and fixing Aluminium Anodised window and ventilator shutters, side hung/sliding /fixed type with out sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats,glazing clips,rubber packing,anodised alminium snap beading ,screwes,anodised fitting such as peg stays 150 mm long (01 Nos),hinges type B-21 100 mm long (02 Nos) ,suitable handle (01 Nos) etc including powder coating of any colour (min thickness of powder coating n less than 50 micron) complete all as specified and directed by Engr-in-charge.

Supply and fixing 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

Supply and fixing 150 mm long Aluminium anodised handles of fabricated type complete all as specified and as directed by Engr-in-Charge.

Supplying, fixing, jointing and testing galvanised steel water tubing 15 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing 20 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supply & fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 25 mm bore size complete all as specified.

Supply and fixing 15mm dia swan neck pillar tap (for oval type WHB) brass chromium plated with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, and fixed complete all as specified and as directed by Engr-in-Charge.

Returning filling any type of soil in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n.exe 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

Supply and fixing 150 mm Salt glazed stoneware drain pipes, grade ‘A’ complete all as specified and as diirected by Engr-in-Charge.

Material and labour cement concrete 1:3:6 type C2 concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in 150mm dia pipe complete all as specified and directed.

Material and labour providing precast cement concrete type B-1 1:2:4 (using 20mm graded aggregate ) in landing, cover slabs (for manholes etc) with CM 1:4 complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size of 1.2 Mtr x 3.00 Mtr effective depth complete all as specified and as directed by Engr-in-Charge.

Material and labour for use waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, chajja and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder, light fitting any type and fan regulator etc and removing from site and making good disturbed surfaces of walls floors etc. complete all as specified and directed by Engr-in-charge.

Material and labour point wiring with 1. 5 Square metrem PVC insulated unsheathed multistranded single core copper conductor cable in PVC surface conduit wiring and incl making good with factory made modular pressed terminal box (recessed) with 1.5 Square metrem PVC insulated copper conductor earth continuity wire for one light/fan point controlled by one switch.

All as per item No.158 here-in-before but for Ceiling fan Point

All as per item No.158 here-in-before but for Exhaust fan Point

All as per item No.158 here-in-before but for one pin 5 A socket outlet on same board

All as per item No.158 here-in-before but for one pin 5 A socket outlet independent point

All as per item No.158 here-in-before but with 4 Square metrem cable for one 6 pin 15A socket outlet point on independent board

Material and labour point wiring with 1. 5 Square metrem PVC insulated unsheathed multistranded single core copper conductor cable in PVC consealed conduit wiring and incl making good with factory made modular pressed terminal box (recessed) with 1.5 Square metrem PVC insulated copper conductor earth continuity wire for one light/fan point controlled by one switch.

All as per item No.164 here-in-before but for one pin 5 A socket outlet independent point

All as per item No.164 here-in-before but for one pin 5 A socket outlet on same board

All as per item No.164 here-in-before but with 4 Square metrem cable for one 6 pin 15A socket outlet point on independent board

Supply and fix switch piano flush, button type 5 Amp SP 250V AC complete all as specified and directed.

Supply and fix switch piano flush button type 15 Amps SP 250V AC complete all as specified and directed.

Supply and fix socket outlet 2-in-1, 5 Pin 5 Amps 250V AC complete all as specified and directed.

Supply and fix socket outlet 2-in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 3 terminals of size 65x25mm. complete all as specified and directed.

Taking down carefully existing LED tube light fitting and keeping aside for refixing after cleaning and providing suitable size flexible copper wire from ceiling rose to light fitting complete all as directed

Supply and fix LED tube light High-quality materials and design. Extruded aluminium housing enhances safety. High quality PC Diffuser. Reliable and robust housing structure, maximize the endurance over the life time slim Integrated design, easy to install Efficacy: 125 lm/W. complete all as specified and directed. Make Crompton Model BRIGHT LINEA Cat Part No - CCS-100-20-65-HL2-DP-NWH or equivalent Note : Light fitting should be not less than 125 lm/W & of Alluminiun body.

Taking down carefully existing LED Mirror light fitting and keeping aside for refixing after cleaning and providing suitable size flexible copper wire from ceiling rose to light fitting complete all as specified and directed

Supply and fixing LED Mirror light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply & fix Wall light fitting along with 9 Watt Bulb complete all as specified and directed.

Taking down carefully existing LED security light fitting and keeping aside for refixing after cleaning and providing suitable size flexible copper wire from ceiling rose to light fitting complete all as specified and directed.

Supply and fix LED Security light Industrial 35 W Powered by built-in, isolated electronic LED driver complete all as specified and directed.

Dismantling existing ceiling fans complete and deposited to MES store yard complete all as specified and directed.

Supply and fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated PVC AC single Phase 230 V / 240V 50 Hz of size 300 mm sweep, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including fabricating and fixing of Fan hooks from ceiling truss/angle iron, required length of down rods (Aas per site requirement) and necessary nuts and bolts complete all as specified and directed.

Supply and fix Exhaust fans Metallic AC single phase 230/ 240 V of size 300 mm sweep,50 Hz with louver of size 300 mm sweep, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including taking down old metalic exhaust fan complete all as specified and directed.

Supply and fix Exhaust fans AC single phase 230/ 240 V , made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including taking down old metalic exhaust fan complete all as specified and directed.

Supply and fix fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block complete all as specified and directed.

Taking down carefully existing storage water heater and keeping aside for refixing after repairing, cleaning and providing suitable size flexible PVC connections all all connecting electrical and water supply accessories complete all as directed

Supply and fix Water heater storage type, electric, capacity 35 litres AC single phase 230/ 240 V and connecting up including making of holes and grouting of nuts and bolts in PCC 1:2:4 type B-0 ( using 12.5 mm graged stone aggregate) block complete all as specified and directed.

Supply and fix Sheet metal enclosures with socket plug top and MCB' SPN enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB complete all as specified and directed.

Supply and fix sheet metal enclosure SPN for DB's when MCB's to be used 4 way with 200 amps bus bar and double door complete all as specified and directed.

Supply and fix TPN DB VTPN 4 way 415 Volts, 50 Hz indoor type double door Sheet metal enclosure IP-43 DB's flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable managenment including mounting arrangement including and fixing of DPX3 MCCB 125 Amps four pole 415 volts as incomer including connection terminal strip complete pre wired with suitable size copper conductor. The DB's should hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Engr-in-charge,

Supply and fix sheet metal enclosure TPN for DB's when MCB's to be used 8 way with 200 amps bus bar and double door complete all as specified and directed.

Supply and fix MCB SPN 240 Volt 10 KA 40 Amp conforming to IS complete all as specified & directed.

Supply and fix MCB SP 6 to 32A complete all as specified and directed.

Material and labour for submain wiring with 3 runs(N+P+E) of 1.5 Square metrem single core,PVC insulated, unsheathed, multistranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed/surface PVC conduit pipe of medium duty not less than 15 mm dia including necessary PVC conduit specials and connecting with suitable size thimble complete all as specified and directed. Note:-3 runs of 1.5 Square metrem size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 193 here-in-before but with 3 runs(N+P+E) of 2.5 Square metrem single core copper FRLS conductor . Note:-3 runs of 2.5 Square metrem size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

All as per item No 193 here-in-before but with 3 runs(N+P+E) of 4 Square metrem single core copper FRLS conductor .Note:-3 runs of 4 Square metrem size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

All as per item No 193 here-in-before but with 6 runs(3 runs P+N+ 2 run Earth) of 6 Square metrem single core copper FRLS conductor and PVC conduit not less than 24 mm dia. Note:-6 runs of 6 Square metrem size PVC copper cable, and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

Material and labour for submain wiring with 3 runs(1 run for Phase+1 run for Neutral &1 run for Earth) of 4 Square metrem single core,PVC insulated, unsheathed, multistranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed wiring with PVC conduit pipe of medium duty not less than 15 mm dia including necessary steel conduit specials and connecting with suitable size thimble, and making good surface of disturbed wall/ceiling/floor as match with existing complete all as specified and directed. Note:-3 runs of 4 Square metrem size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

Material and labour for earthing complete with GI or steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI earth strip 4 Sq mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of (0.68mm) 8 mesh per liner inch, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I and specified including provision of earth wire protected by 40mm dia medium grade GI pipe and watering pipe shall be 20mm bore medium grade GI pipe, and including all excavation and earth work & connecting the earthing to an earthing test point /transformer nuetral/body/ Lt panel etc. and testing on completion, complete all as specified & directed by Engr-in-Charge.

Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and directe.

Supply and Laying XLPE insulated galvanised steel strip or wire armoured elctric power cable with stranded aluminium conductor 1100 V grade of size 50 Square metrem 3.5 core after cutting to required length with necessary glands, nuts, bolts, and lugs complete all as specified and directed.

Supply and Laying XLPE insulated galvanised steel strip or wire armoured elctric power cable with stranded aluminium conductor 1100 V grade of size 6 Square metrem 4 core after cutting to required length with necessary glands, nuts, bolts, and lugs complete all as specified and directed

Excavation in trenches soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out excavated soil/sand/unsv LT Cable for laying of cable and getting out complete all as specified and directed.

Sand cushioning and covering of UG cable using crushed metal sand in trenches for cable protection all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in hard /loose soil complete all as specified and directed by Engr-In-Charge.

Removing excavated material n. exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr above the starting point complete all as specified.

Material and labour for brick well burnt Class ‘B’ as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches all as specified and directed

Cutting existing road/hardstand of any type by using crow bar chisel uprto a depthof 30 cm for laying GI pipe including making good the surface by returning filling watering ramming in layers 150 mm thick PCC 1:2:4 over 200 mm thick hard core of broken bricks/stones over returning filling watering ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engineer-in-Charge.

Material and labour for GI Tubing Light grade (ISI marked) with all fitting/acessories for protection of cable on pole/wall and under road crossing including clamps, nut bolt etc all as specified and directed of size 50mm dia complete all as specified and directed.

M.K Engineers

M/S RAJESH AGARWAL

G M CONSTRUCTION COMPANY

V S ENTERPRISES

M/s Pradeep Kumar

VERDHMAN ASSOCIATES