Construction of Multi Purpose Centre Under PM JANMAN Funded by Ministry of Tribal Affairs Government of India in PVTG Area of Maram Tribe, at Naojai Village, Senapati District, Manipur.

Amount

[A]: CIVIL WORK

Sub-Head 1 :-Surface Dressing

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m.All kinds of soil.

Sub-Head 2:-Earth Work

Earth work in excavation in foundation trenches or drains including dressing of sides ramming of bottoms lift up to 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres

Filling available excavated earth (excluding rock) in trenches , plinth side of the foundation etc. in layers not exceeding 20 cm in depth ,consolidating each deposited layer by ramming and watering lead up to 50 metres and lift upto 1.5 metres

Supply and filling in plinth with sandy soil under floors including watering, ramming consolidating and dressing complete

Sub-Head 3:-Concrete & RCC Work

Providing and Laying in position cement concrete of specified grade excluding the cost of centering & shuttering ,1:4:8(1cement:4coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works upto plinth Level: Concrete of M25 grade with minimum cement content of 330kg/cum

Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works above plinth Level up to Floor V level: Concrete of M25 grade with minimum cement content of 330kg/cum

Reinforced cement concrete work in beams,suspended floors, roofs having slope upto 15 deg landings, balconies, shelves,chajas, lintels, bands,plain window sills, staircase and spiral staircases above plinth level upto floor five level, excluding the cost of centering, shuttering, finishing, and reinforcement with 1:5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size).

Providing and laying damp proof course 50 mm thick with concrete cement 1:2:4(1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size)

Applying a coat of residua lpetroleum bitumen of penetration 80/100 of approved qualit yusing 1.7kg per sqm on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in Kerosene oil.

Sub-Head 4:-Reinforcement Steel/ Rebar work

Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete upto plinth Level.Thermo Mechanically Treated Bars

Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete above plinth Level.Thermo Mechanically Treated Bars

Sub-Head 5:-Form work

Foundation, footings, bases of columns etc. for mass concrete.

Columns, pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof 12mm ply

Sub-Head 6:-Brick work

Brick work with 1st class common burnt clay F.P.S (non modular) bricks in foundation and plinth in:

Half brick masonry with first class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand)

Sub-Head 7:-Wood work / alluminium work

Providing woodwork in frames of doors, windows, celestory windows and other frames wrought, framed and fixed in position with hold fast lugs or with dash fastner of required dia and length (hold fast lugs or with dash fastner shall be pais separately) with Local best quality Tolhao wood.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required sizes with necessary screws with Local best quality Tolhao wood 35mm thick

Providing and fixing aluminium sliding bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 300x16mm

Providing and fixing aluminium Tower bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 300x10mm

Providing and fixing chromium plated Brass handles with necessary screws etc.complete.125mm

Providing 40x5mm flat iron hold fast 40cm long I/c fixing to framed with 10 mm dia .bolt nuts and windows plugs and wooden plugs and embedding in cement concrete block 30x10x15mm 1:3:6(1cement:3 coarse sand:6 graded stone aggrt.20mm nominal size)

Sub-Head 8:-Finishing work

Painting with oil type wood preservatives of approved brand and manufacture: New work (two or more coats)

Polishing on wood work with ready made wax polish of approved brand and manufacture: New work

12 mm thick plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:4 ( 1 cement : 4 fine sand )

15 mm thick plaster on rough side of single or half brick wall of mix 1:4 ( 1 cement : 4 fine sand )

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Deluxe Multi surface paint for interior and exterior using Primer as per manufacturers specifications:Two or more coats [email protected] Lts/10 sqm)over and including one coat of special primer applied @0.75kg/10sqm.

Sub-Head 9:-Flooring work

Cement Concrete flooring 1:2:4 (1 cement : 2coarse sand : 4 graded stone aggregates 20 mm nominal size) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stine aggregate.

Neat cement punning

Sub Head 10: Steel work & Accessories

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc.

P/F M.S. fan clamps type-I or II of 16mm dia. and M.S.bar bent to shape with hooked ends in RCC slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Sub Head 11: Roofing Work & Ceiling Work

Steel work in built up tubular (round, square, or rectangular tubes etc) trusses etc, including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc complete with Electric resistance or induction butt welded tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120gsm as perIS:277, in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and poluester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desire by Engineer-in-charge. The sheet shall be fixed using self drilling/ self tapping screws of size (5.5+55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with Precoated galvanised iron profile sheets 0.35mm thick

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120gsm as per IS:277 in 240mpa steel grade 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, GI plain and bitumin washers complete:

Ridges plain(500-600mm), Precoated galvanished iron profile sheets 0.35mm thick

Gutter(500-600mm), Precoated galvanished iron profile sheets 0.35mm thick

[B]: Internal Water supply & Sanitary Installation

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe,with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with CI Brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:510x1040 mm bowl depth 225mm.

Providing and fixing wash basin with CI brackets, 15mm dia CP brass pillar taps, 32 mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White vitreous china wash basin size 550x400mm with a pair of 15mm CP brass pillar tap.

Providing and fixing PTMT Waste Coupling for wash basin and sink of approved quality and colour

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.24.37.1 Flexible pipe: 40mm diameter

Providing and fixing 600 x 450 mm levelled edge mirror of Indian make superior glass (of approved quality) quality complete with asbestos sheet ground, fixed to wooden cleat with C.P. brass screws and washers.

Providing and fixing PTMT towel rail complete with bracket fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings arrangement of approved quality and colour, weighing not less than 105gms

Providing and fixing CPVC. pipes having thermal stability for hot o& cold water supply ,including all CPVC plain & brass threaded fotting, including fixing the pipe with clamps at 1.00 m spacng.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.

15 mm diameter

20 mm diameter

25 mm diameter

Providing and fixing CP brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms .15mm nominal bore.

Providing and fixing of C.P brass stop cock (concealed) of approved quality . 15 mm diameter

Providing and fixing PTMT pillar cock of approved qualityand colour . 15 mm nominal bore ,98 mm long,weighing not less than 75 gms

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS:12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but withou fittings and the base support for tank.

Providing and fixing PTMT extension nipple fro water tank pipe, fittings of approved quality and colour.25 mm nominal bore weighing not less than 62 gms

Ready Made Septic Tank

Steel Work For Elevated Water Tank Stand:

Structural steel work in single section fixed with or without connecting plate including cutting,hoisting, fixing in position and applying coat of approved steel primer all complete:

[C]: Internal Electricfication & Installation

Wiring:-

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in PVC casing & capping with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc. as reqd.

Group A

Group B

Group C

Wiring for light point / power plug with 2x4mm2 FR PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 FR PVC insualted copper conductor single core cable for loop earthing etc. as reqd.

S/F suitable size GI box with modular plate and cover in front on surface /recess i/c P/F 3 pin 5/6 amp socket outlet and 5/6 amp modular switch, connection painting etc. as reqd.

S/F suitable size GI box with modular plate and cover in front on surface /recess i/c P/F 6 pin 15/16 and 5/6 amp modular socket outlet 15/16 amp modular switch, connection painting etc. as reqd.

Wiring for circuit / sub-main wiring along with earth wire with (the following sizes of) FR PVC insulated copper conductor single core cable in PVC casing & capping etc. as reqd.

1. 2x2.5mm2 +1x2.5mm2 earth wire.

2. 2 x 4mm2 + 1 x 4mm2 earth wire.

3. 2 x 6mm2 + 1 x 6mm2 earth wire.

Supply of 16mm2 2 core PVC/ XLPE insulated Al. cond. heavy duty armoured cable 1.1 KV grade.

Laying of 1 no. PVC insulated PVC sheathed power cable of 1.1 KV. grade of size not less than 25mm2 direct in ground i/c excavation, sand cushioning, protective covering & re-filling the trench etc.

Fitting Accessories

S/F 15W Surface mounting LED down light with white powder coated aluminum housing with integrated electronic driver i/c connection as reqd.(HAVELLS)

S/F 48'' sweep (1200mm) A.C. ceiling fan complete with down rod, cannopy, 3(three) blades but without regulator etc. as reqd. (Make Bajaj/Usha or Similar).

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc. as reqd.

S/F 305mm sweep exhaust fan complete with all accessories i/c connection etc. as reqd.

Switch Gear:

SITC of Cubicle type floor mounted Essential panel fabircated out of 16 SWG MS street fully front operated suitable for 3 phase 4 wire 415 V AC supply system having the folowing switch gear and accessories i/c fabrication, paining, erection on floor with required civil works making good the damages etc.

S/F (2+6way) single pole and neutral, prewired, sheet steel, MCB distributon board, 240 V on surface/recessd complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, hinged front acrylic cover for MCB knobs, detachable gland plate, interconnection, phosphatized and powder painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

Supply and fixing of 250mm x 300mm x 100mm deep metal boxes with phenolic laminated sheet cover in front.

S/F 63 amp, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissiong etc. as reqd.

S/F 5 amp. To 32 amp. Rating 230V 'B' series MCB for lighting and other load of single pole in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Earthing Items:

Earthing with copper earth plate 600mm x 600mm x 6mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe ec. (but without charcoal or coke and salt).

Extra for using salt & charcoal for copper plate earth electrode as reqd.

P/F 8 SWG dia copper wire on surface or in recess for loop earthing along with existing surface/recessed conduit wiring/sub-wiring/cable etc. as reqd.

P/L earth connection from earth electrode with 8 SWG dia G.I. wire in 15mm dia G.I. pipe as reqd.

ASEM NINGTHEMJAO SINGH (BID ID -9276)