SPECIAL REPAIRS TO TOILET BLOCK IN BLDG NO P44 MODEL ROOM FALSE CEILING IN BLDG NO T09 T-17 AND PROVISION OF TOILET 20 X WC MF AREA OF JRC INCL CERTAIN MINOR WORKS UNDER GE WEST BAREILLY

Amount

Surface exscavation n.exc 30 cm deep and avaraging 15cm deep and getting out in soft /loose soil.

Excavation in trenches n.exc 1.5m wide and 1.5m deep for foundation etc in soft/loose soil and getting out all as specified.

Treating the bottom and sides of excavation, on filled soil and soil below plinth protection at the rate of 5 litres of emulsion per square metre of surface area

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M&L for Cement concrete 1:5:10 type E-2 (using 40mm graded stone aggregate) as in foundation, filling, sub base and mass concrete.

M&L Brick work with fly ash bricks ,old size brick straight or curved on plan exceeding 6 M mean radius built in CM 1:6 complete all as specified and directed

M&L Brick work with fly ash bricks ,old size brick straight or curved on plan exceeding 6 M mean radius built in CM 1:4 complete all as specified and directed

M&L brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cm (1:4) all as spd and directed

M&l for Rendering 15mm thick on fair faces ( or other than fair faces ) of brick or concrete surfaces in CM (1:4) finishing the surfaces even & smooth wihout using extra cement (external) using WPC (wpc shall be measured & paid separatly).

M&l for Rendering 15mm thick on fair faces ( or other than fair faces ) of brick or concrete surfaces in CM (1:6) finishing the surfaces even & smooth wihout using extra cement (internal).

M & L for rendering 10 mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished the surface even and smooth without using extra cement complete all as spd and directed

M&L for preparation of new plastered surfaces on ceiling and applying three coats of white wash etc complete all as specified and directed

M&L preparation of new wall surfaces and applying two coats of cement base paint over a one coat of cement primer.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash etc complete all as specified and directed

Supply only integral water proofing compound.

M&L for RCC M 25 design mix concretes mechanically crushed stone aggregate as in RCC slabs shelves roof proj/drops/chajjas etc all as spd.

Ditto but in beams, cantilevers, lintels over 1.50m spam.

Providing cement concrete 1:2:4 type B-I (using 20mm graded stone aggregate as in lintels up to 1.50 mtr clean span, cills siesmic and other similar bands, plinth courses, coping, bed plates and the like including weathering slightly rounded or chemfered angles and throating as directed.

Mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.

Ditto but 8 mm dia TMT bars.

Ditto but 6mm dia and over upto and including 8mm dia in stirrups, spaces and binders.

Form work to soffits of suspended slabs such as roof slab, floor slab and similar work n.exc 200mm thick with rough finished flat surfaces.

Form work to roofs, chhajjas, trough and similar items including edges with rough finished flat surfaces of concrete.

Form work to sides and soffits of floor or roof beams haunching, lintels, cantilever, shelves including supported over hangs etc. with rough finished flat surfaces of concrete.

S&F Steel ventilators with top hung shutter including hinges ,steel peg stay , including one coat primer and two coat paint completed all as spd.

S&F mild steel framed work such as grills grating etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, barrel iron doors ladders framed balusters walk ways railing frame work of water tanks and similar work confirming to Fe -290 Gde-E-165 all as spd and directed .

M&L 25mm thick cement concrete type B1 1:2:4 using 20mm graded stone aggregate in floor finishes even and fair to receive floor tiles.

Supply and providing water proofing treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen,MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness all as specified and directed and described as under :-

(a) Prepartion of RCC foof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm including cleaning surface, all as per manufacture'"s specification complete all as specified and directed.

(b) Supply & providing water proofing treatment with polymeric proofing membrane of 3 Kg/Sqm HYPERPLAS STANDARD/MULTIPLAS STANDARD consting of 100 micron HMHDPE film centre core including coating he surface with the compatible primer and torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed.

M/L for solar reflective bituminous aluminium paint @ 0.10 Kg per Sqm over membrane surfaces as in roof treatment complete all as specified

M & L for colour glazed ceremic coloured tiles in vertical surface 300 x 450 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick screed bed or bedding layer of cement mortar 1:4 cement and dismantling of wall tile including cement mortar bedding complete all as specified or as directed. all as spfd or as directed.

M & L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:6 for laying floor finishes all as specified and directed.

M&L providing "RAJSHRI" BRAND FACTORY MADE PVC INTERNAL DOOR FRAME (PRELAM) of size 100 mm x 45 mm with a wall thickness of 5 mm (+- 0.25 mm ) made out of extruded 5 mm (+- 0.25 mm ) thick PVC sheet manufactured by an ISO 9001-2008 certified company and by joining 3 nos Heat bent PVC sheet sections. the inside section of size 90x30 mm shall be made from plain colour PVC sheet of 5 mm (+-0.25 mm ) thickness the inside section will be covered by sticking two sections of size 30 x 35 mm and 70 x 45 mm made from (+-0.25) thick plain PVC sheet The frame shall be mitre cut at two corners and joined with 4 nos of 150 mm long brackets of 15 mm x 15 mm MS square tube The two vertical door frames are to be reinforced with 40 mm x 20 mm MS tubes of 19 guage through out the farme The door frame shall be fixed to the wall using 8/100 mm long screw through the frame by using anchor fastners. A minimum of 4 nos screw to be provided for each vertical members and minimum 2 nos for horizontal member etc complete as per manufacturers specifications and directions of engineers-in-charge

M&L in providing 30 mm thick RAJSRI brand factory made internal PVC flush door shutter wood free consisting of frame made out of M S tubes of 19 guage thickness and size 20 mm x 40 mm for siles as well as top bottom and lock rail MS frame shall have a coat of metal primer of approved make and manufacturer. The inside panel shall consist of 20 mm thick multichamber hollow PVC section 1 mm wall thickness bonded using solvent cement/ cynoacrylate adhesive with 5 mm (+-0.25 mm) thick plain/prelam PVC sheet manufactured by an ISO-9001-2008 certified company on both side of the inside panel All the four edge of the panel to be sealed with lipping of 10 mm thick and 20 mm wide PVC sheet baton( made by sticking 2 nOs PVC sheet of 5 mm ( +0.25 mm ) thickness using PVC solvent cement adhesive Door edge lipping to be painted with PVC ink of matching colour of plain/prelam moulded PVC sheet of door 0.20 mm thick ( 5mm x 4 mm) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos stainless steel butt hinges of size 100 mm * 25 mm * 25 mm and 50 mm long steel screws drilled suitable to pass through both the wall of the MS tube other hardwares should be fixed with 25 mm * 8mm size steel screws etc complete as per direction of engineer-in-charge, manufacturers specification and drawing

S&F alluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 300 mm

S/F 100mm stainless steel butt hinges.

S/F 150mm length extruded aluminium alloy handles,fabricated type, anodised.

S&F 150mm length aluminium anodised barrel tower bolt of extruded section.

S&F sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane of 4 mm thick etc

M&L 75mm thick cement concrete 1:3:6 type C-1 ( using 20mm graded stone aggegate) as in plinth protection finished even and smooth without using extra cement ( laid in alternate bags).

M&L for salt-glazed stoneware gully traps,150x150 square or round mouthed, type "P"

Concrete bed to drain pipes of 150mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified

M&L for 100 mm dia Reinforced concrete pipes, class NP2 laid in trenches and jointed complete with collars as specified

Returning, filling including spreading, levelling and well ramming in layers not exceeding 25 cm in each layer as in hard / dense soil complete.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 sectiion) in cement concrete 1:2:4 (type B1) smooth finished, and reforming benching as required of pipe 150mm dia complete

Removing excavated soils n.exc 50mtrs and depositing where directed at a level n.exc 1.50m above the starting point.

S&F Rotional moulded polythene water storage tanks ( cylendrical vertical with closet top) hoisted and fixed in position all as spd in SSR Part-I 500 ltr capacity.

S&F 15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

S&F 20 GI Tube medium grade galvanised with all fittings and fixed complete to walls, ceilings or laid in floor or trenchs etc.

S&F 15 GI Tube medium grade galvanised with all fittings and fixed complete to walls, ceilings or laid in floor or trenchs etc.

S&F stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle scrwed both ends for iron pipes or for unions and fixed bore pipe 20mm.

S&F stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle scrwed both ends for iron pipes or for unions and fixed bore pipe 15mm.

S&F fancy type chromium plated angle valve with flange 15mm size Make: Jaguar/EssEss. Or equ

S&F fancy type chromium plated cancealed stop cock with long shank and cup ( concealed tyoe) Make : Jaguar or equ

S&F Bib tap long nose with flange cast copper alloy chromium plated fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed (15mm size) Make Jaguar/Ess Ess. Or equ

Supply & fixing vitreous china wash down water closet pan pedestal patern white /coloured including CP EWC Jet with seat cover Complete and taking down old seat fixing bolt flush pipe complete all as spd and directed by Engineer -in- charge.

S&F vitreous china orissa pattern, size 580x440mm white with integral foot rests and "P" or "S" trap, connection to trap and to flushing pipe front or back inlet, including lime concrete bedding, trap . complete all as specified and as dirceted by the engineer-in-charge. (excluding flushing cistern and flush pipe).

S&F 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair chromium plated shower rose with swivel joints and including fixed to GI tubing 15mm bore size of shower not less than 125mm.

S&F for 6mm thick looking mirror fixed on 12mm thick marine plywood with powercoated aluminium frame alround the mirror including mounted on wall size 1.50x 0.60 complete all as specified and directed.

M&L for Marble works 16 to 18mm thick Green marble machine cut and machine polished,and moulding, one side green marble, over/jambs of doors/ window cills,and urinal partition wash basin platforms and flooring,skirting/dados like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble

S&F fancy type viteous china counter top, wash hand basin, "OVAL" shaped,white of size 550x400mm including bottle trap, fixed in green marble/ granite by cutting on oval shaped etc completed all as specified and directed .(Green marble/ granite shall be measured and paid separately) Make cera,parryware

S & F urinal valve auto closing system with built in control cock & wall flange valve 15 mm bore including urinal sperader of CP complete all as specified and directed Make jaquar or equivalent Cat no PRS-077.

S & F vitreous china urinal half stall type colours excluding flushing cistern flush pipe and waste pipe.

S&F CI floor traps with grating complete 100mm bore outlet including jointing to waste pipe fixed in cement concrete type B1 1:2:4.

S&F Brass CP piller cock water fall type down for iron pipe and fixed bore of pipe 15mm. Make: Jaguar/Ess Ess.

S&F PVC (SWR) pipes single socketd in any length with rubber ring joints laid in trenches or in floor 110mm bore or fixed to walls.

Ditto but 75mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR) bends any radius 110mm bore.

S&F PVC (SWR) junction single or double equal or unequal 75mm bore.

S&F PVC (SWR) junction single or double equal or unequal 100mm bore.

S&F PVC (SWR) vent cowl 75mm.

M&L PVC (SWR) floor trap plain with grating including jointing with solvent 75mm dia of contilent.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75mm dia of contilent.

S/F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls.

M&L for hard core of stone not exc 63 mm guage spread, levelled in layers not exc 100mm watering and well ramming to true surfaces complete.

M & L 75mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M& L for 30X30cm providing precast cement concrete rubber moulded chequered coloured tiles 25 mm thick even finished on top of approved design and pattern complete all as specified and directed screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 for laying floor finishes all as specified and directed.

M&L for salt-glazed stoneware gully traps,150x150 square or round mouthed, type "P" fixed in PCC 1:2:4 complete all as specified.

S&F 100mm cast iron sanitary connection socket to fit WC out let

S&F 75mm bore CI soil waste / vent pipe (spun type) in any length with or without ears with cement joint to wall with stack clamps out of 110mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing end of stays to wall or roof etc.all as specified including black japan paints Make neco

S&F 100 mm bore CI soil waste / vent pipe (spun type) in any length with or without ears with cement joint to wall with stack clamps out of 110mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing end of stays to wall or roof etc.all as specified including black japan paints Make neco

M & L for construction of septic tank for 50 Users capacity using sub class B bricks old size, with and including necessary excavation earth work, brick work, concrete work, plastering, returning filling in soft/ loose soil and removal of surplus soil to a distance n exc 50 Mtrs etc complete all as shown in typical drawings No TD/217 sheet 1/7 to 7/7 complete all as spd and directed

M & L for construction of Soak well 1.80 mtrs dia and 3 mtrs effective depth with and including necessary excavation earth work, brick work, concrete work, plastering,filling with brick bats, PCC on top returning filling in soft/ loose soil and removal of surplus soil to a distance n exc 50 Mtrs etc complete all as shown in typical drawings No TD/309 sheet 1/4 to 4/4 complete all as spd and directed

Demolition of cement concrete (unreinforced) in ground floors, and pavings n.exc. 15 cm thickness (below or above GL)

Demolition of reinforced cement concrete of any description and in any position otherwise specifically provided (reinforcement cut as required to facilitate demolition)

Demolition of brick work built in cement mortar in any description.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) n exc 1.5 Sqm each

All as above but exceeding 1.5 Sqm but n exc 4 Sqm each

Taking down cement plaster on brick/ stone walls etc any description incl raking out joints, hacking for key, scrubbing down with water etc

M & L applying one coat of cement based paint on old decorated or undecorated wall, roof surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified.

S&F in repair stop valve 15mm dia, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union and fixed all as specified or as directed. .

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts.

S&F fancy Bib tap 15mm dia cast copper alloy chromium plated with crutch or buter fly handle screwed down (Pressed for iron pipe) fixed in repairs

Taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc.

M & L 75 mm dia cost Iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) as in repairs

S&F 75 mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door

S&F CI 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door

S&F 100mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door

S&F CI 100mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door

Dismantling water tanks and removing to store capacity exc 250 and not exc. 500 litres complete all as specified and directed.

S & F steel window with side hung shutters incl box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

All as per item above but without glazing bars.

S&F framed work such as grills, gratings, etc..with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290. Gde-E-165

Dismantling of floor or herth tiles including cement mortar bedding but not backing all as specified and directed

S & F Non skid ceramic coloured tiles7 mm to 8mm thick (square /rectangular )area of each tiles exceeding 0.11sqm but n . Exc 0.18 sqm superior premium quality, grade B-1 as per IS in Water splashing floors etc . set and jointed in neat cement slurry and pointed in white or coloured cement including 15mm thick screed bed or bedding layer in cement mortar 1:4 .

S&F coloured granite (of any type)tiles 20mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing after roughing to surfaces and applying screed bed of 10mm thick of cement mortar 1:3 complete all as specified and directed.

S & F Sheet glass ordinary quality 3 mm thick and glazing with oil putty in squares n exc 0.5 Sqm in each pane.

S&F in repairs stain less steel wire cloth 0.36mm nominal dia of wire and average width aperture 1.40mm and fixed with stain less steel wire staples

Taking up or down steel tubing and connections, including cleaning for refixing removal to store bore of pipe 15mm.

Taking up or down steel tubing and connections, including cleaning for refixing removal to store bore of pipe 20mm.

Taking up or down steel tubing and connections, including cleaning for refixing removal to store bore of pipe 25mm.

Refixing old steel tubing and connection in new or old position (wall, ceiling,floor etc.) bore of pipe 20mm

Refixing old steel tubing and connection in new or old position (wall, ceiling,floor etc.) bore of pipe 25mm

S&F tubes ‘medium’ grade galvanized with all fittings fixed complete to walls and ceiling or laid in floor.bore of tube 25mm.

S&F in repairs, brass chromium plated shower rose 125 mm size

M & L preparation of new steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M & L preparation of steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint including preparation of the old surfaces.

Extra over for moulding of granite/ green stone platforms as directed.

S & F CP pillar central hole basin mixer without popup waste system with 450mm long braided hoses hot and cold water screwed down for iron pipe and fixed bore of pipe 15 mm Make- Jaguar cat no 23167B/Ess Ess

S& F urinal spreder of CP any colour for fixing with 15 mm dia pipe (Minium wt 60 gms)

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for proving cement concrete (1:2:4 Type B0 12.5 mm graded stone aggreate in roof kerbs or mud stops rounded or chamfered pm edges

M & L for 15 mm thick rendring in cement mortar 1:3 on fair faces of brick or concrete surfaces finished ceven and soomth without using extra cement and using with water proofing compound complete all as specified and directed.

M&L for RCC 1:2:4 using 20mm graded mechanically crushed stone aggregate as in RCC shelves roof proj/drops/chajjas etc all as spd.

M& L providing precast cement concrete rubber moulded coloured interlocking tiles 60 mm thick with grey cement and pigment of approved design and pattern laid over a layer of 25 mm thick sand cushion including filling the joint with sand complete all as specified

M&L for PCC Kerb stone outer coloured surface machine pressed factory made of size 300 mm long 100mm wide and 350mm deep in PCC 1:2:4 type B-0 using 12.5 mm grade stone aggregate, jointed in CM 1:4 complete all as specified and directed.

M&L providing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in benching, coping, bed blocks including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and directed by Engineer-in-charge.

Dismantling asbestos cement (corugated or semicorrugated etc ) sheets, in roof covering.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws as specified.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws as specified.

M & L for colour glazed ceremic coloured tiles in vertical surface 300 x 200 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick screed bed or bedding layer of cement mortar 1:4 cement and dismantling of wall tile including cement mortar bedding complete all as specified or as directed. all as spfd or as directed.

M & L for 18-20 mm thick machine cut kota stone flooring and jointed with grey cement slurry fixed with pigment to match to shade of the slab including rubbing and mirror polishing over screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes all as specifiedor even and rough with and including dismantling floor, hearth or wall kota stone slab including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L machine cut Kota stone slab 18 to 20mm thick in riser of steps skirting, dado and pillar,landing in single piece with round nosing with three numbers of serration, laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing ding and inclucding 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed dismantling of wall tile including cement mortar bedding complete all as spd and directed

Dismantling wall and ceiling board or insulation boards/ slabs/ blankets, any thickness, including cover fillets.

M&L for 4mm thick E-Board classic (everest or equivalent) tiles for insulation and accoustic purpose 60cm x 60cm with and including powder coated galvanised iron snap grid with 32x25x1.5mm thick Tee section and 32x25x1.5mm thick algle section with all hanging/supporting arrangements as in false ceiling and making good disturbed surface complete all as specified and directed.complete all as specified and directed.

Dismantling timber scantlings 40 sqcm & over in section , in any position unframed work.

M&L 2nd class hardwood scantling, clean sawn as in unframed work as in roof truess and purline.

M&L Preparation of old wall surfaces and applying two coats of white washing on wall all as spd.

M&L applying one coat of cement base paint on old plastered surfaces of wall including preparation of surfaces

Complete removal of existing treatment from wall/ ceiling surfaces and rubbing down with sand paper to have even and smooth surfaces

M&L for applying 3 mm thick layer of birla wall care putty on wall/ceiling surfaces incl rubbing down the surfaces with sand paper after getting dried all as directed to obtain a smooth & even surface complete all as spd and directed.

M & L applying two coats of oil bound distemper on old plastered surfaces of wall complete all as specified and directed

M & L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete

M&L for preparation of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote one coat.

M&L for MS framed work of angle, tee, F.I, conforming to Fe-290 (Gde E-165), as in roof trusses including distance pieces, cleats etc. welding or riveted complete all as specified and directed.

M & L Point wiring with 1.5 Sqmm(Nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor single core cable (FRLS)drawn through and including PVC non metallic conduit of 20 mm dia ISI marked with complete accessories,including sunk mild steel 1.6 mm thick terminal boxes with 3 mm thick bakelite sheet top cover ISI marked complete including PVC insulated and unsheathed single core multistranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth and earth dolly complete all as specified and directed for the following :-

(a) One light point controlled by one one way switch

(b) One exhaust fan point controlled by one one way switch

All as per item 3 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded complete all as specified.

S&F switch piano flush type polycarbonate single pole one way 5 Amps.

S&F socket outlet polycarbonate 2 in 1, 3 pin 15 Amps flush type.

S&F Ceiling rose 3 phase/PVC/polycarbonate, insulated body.

S&F LED light fitting with PVC extruded batten 20watt 4 feet white complete all as specified and directed.

S&F LED bulk head luminaries with lamp holder 1x10watt etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 volt 50 Hz including 6 Watt LED all as speified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED retrofit lamp B-22 holders base with polycarbonate body and aluminium heat sink warm white of all as specified.

S&F double door MCB distribution boards sheet steel, powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail single phase and neutral confirms to IS : 13032-1991 of 4 ways Make Indo Asain or Equivalent

S&F Miniature circuit breakers (MCBs) ISI marked 240 Volt, 50 Hz, single pole 6-32 Amps, breking capacity 10 KA Make Indo Asian or equivalent.

S&F Miniature circuit breakers (MCBs) ISI marked 240 Volt, 50 Hz, SPN 40-63 Amps, breking capacity 10 KA.Cat No DHMCCSNF040/50/63of Make - Havells/Cat Part No 408618/19/20 of Make Legrand/Cat part No NCN240N/50N/63N of Make Hager or equivalent Make of L&T/Scheneider complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600x 6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and connecting to main switch or switch board complete and incl PCC masonry pit of 300x300x300mm interier diamentions in PCC 1:2:4 type B1 RCC cover with GI frame, charcoal and common salt 15cm in layers all round the earth plate, 15mm dia GI watering pipe, a funnel with wire mesh should be provided on top of watering pipe complete all as specified as per electric plate No 3of SSR 2009 including testing after completion.

Supply and fixing 1100 volt grade heavy duty cable PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connectiuons suspended by insulating hangers not more than 1 meter apart including 4 mm dia suspension wire, one twin core cable flat or circular of size 6 Sqmm all as specified.

Supply, installing, testing and commissioning exhaust fans heavy duty 300 mm sweep, 230 volt, AC, 50 Hz single phase with louvers make Standard complete and including connecting up with flexible three core copper conductor from ceiling rose to fan connector etc all as specified. Make - Bajaj/Havells or equivalent approved make.

S&F in replacement mirror light fitting of 1 x 9 watt LED type of size 2 fit , clear acrylic cover including mounting on wall complete all as specified and directed.

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified.

S&F in replacement mirror light fitting of 1 x 9 watt LED type of size 2 fit , clear acrylic cover including mounting on wall complete all as specified and directed.

Supply and fix flush sheet metal enclosure SPN DB 8 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unsv all as specified and directed.

Supply, installing, testing and commissioning ceiling fans heavy duty 1200 mm sweep, 230 volt, AC, 50 Hz single phase complete and including connecting up with flexible three core copper conductor from ceiling rose to fan connector etc all as specified.

M&L & installation of steel tubular swaged pole complete with cast iron base plate finial taper plug, bolts, nuts and screw as specified type 410 SP-55 11 mtr long with provision of four lights connected through a ring of suitable GI pipe complete all as specified and directed.

S & F security flood light with PDC aluminium housing with sealed toughned glass cover SMD LED 150 W with secondary lens 150 Watt complete all as specifies and directed.

Supply and fix loop-in-loop out box of size 20x20x15cm made out from 1.6mm thick PVC sheet weather proof, dust and vermin proof with hinged door and locking arrangements with slanting cover on top and provision of 2 Nos aluminium bus bar of size 12mm x 2mm-2 Nos fixed on insulator and one MCB SPN of capacity 40-63 Amps complete fixed on pole with and including suitable size MS flat iron clamps, nuts,bolts & washers etc complete all as specified and directed

Notes:-

REHAN CONSTRUCTION

SANJEEV ENTERPRISES

TRISHOOL ASSOCIATE

M/S Gupta and Company

Shikhar ji Enterprises