Loading
Loading…
Loading…
Tender Value
₹54.0 L
EMD Value
₹1.1 L
Closing Date
13 Apr 2026, 12:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
DEN SPL
15 conditions · 3 needing a document upload
Financial Eligibility Criteria (Clause 10.2 of part-I GCC-2022):- The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. (Important Instruction: "The balance sheet and all other financial documents attested/certified by the Chartered Accountants (CA) to substantiate fulfillment of Financial Eligibility Criteria should be with UDIN, failing which the offer shall be considered as incomplete and will be summarily rejected without any further reference" Vide letter no. CE/Works/ECR/HJP's letter No.ECR-HQ0ENGG (CONT)/ 0009/2025 dtd. 18.11.2025 (ii) Gazette Notification No.1-CA (7)/192/2019, dated 02.08.2019 of the Institute of Chartered Accountants of India, published in the Gazette of India).
Technical Eligibility Criteria (Clause 10.1 of GCC-2022): (a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b)(1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b)(3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.
Note: for subletting of work costing up to Rs.50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note for Item 10.1: (Clause 10.1 of part-I GCC-2022): Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Similar Nature of work:- Installation/Replacement/Repair of water supply system or sewage schemes.
11 conditions · 7 needing a document upload
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be.
If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender.
After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society / HUF/LLP etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted.
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association/Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate.
(a) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. as the case may be. Following documents shall be submitted by the tenderer: - (b) Following documents shall be submitted by the tendeerer in case of Sole Proprietorship Firm; (i) An undertaking that he is not blacklisted or debarred by Railway or any othr Ministry/ Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which he was /is a partner/member. Concealment /wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022. (c) Following documents shall be submitted by the tenderer in case of HUF; (i) A copy of notarized affidavit on stamp paper declaring that he who is submitting the tender on behalf of HUF is in the position of Karta of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) An undertaking that the HUF is not blacklisted or debarred by Railway or any other Ministry /Department f Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member f the partnership firm or JV in which HUF was / is a partner/member. Concealment/wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (iii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022. (d) Following documents shall be submitted by the tenderer in case of Company registered under Companies Act 2013; (i) The copies of MOA(Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate o Incorporation (iii) A copy of Authorization /power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sing the tender on behalf of the company and create liability against the company. (iv) An undertaking that the Company is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which the Company was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022. Society/Trust. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
(e) Following documents shall be submitted by the tenderer in case of LLP (Limited Liability Partnership): If the tender is submitted on behalf of a LLP registered under LLP Act-2008, the tenderer shall submit along with the tender: (i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking that the LLP is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of JV in which the LLP was / is a member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 6 2 o f t h e General Conditions o f Contract. ( v ) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC2022. (f) Following documents shall be submitted by the tenderer in case of Partnership Firm: The tenderer shall clearly specify that the tender is submitted on behalf of a partnership firm. (i) A notarized copy of partnership deed. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm. (iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022 and clause 18 of GCC-2022. (g) Following documents shall be submitted by the tenderer in case of Registered Society & Registered Trust (i) A copy of the Certificate of Registration (ii) A copy of Deed of Formation (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC-2022.
An undertaking that the Proprietary firm /Partnership firm/Company /Joint venture (JV) Registered society /Registered Trust /HUF/LLP ect. He is not blacklisted or debarred by Railway or any other Ministry/Department of Gov. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of JV in which the LLP was / is a member .Concealment/ wrong information in determination under Clause 62 of the General Conditions of Contract. For detail refer para 5 & 5.1 as above and GCC-2022 .
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
A copy of Documents against eligibility criteria must be submitted along with the E-tender. No any documents against the same will be entertained in the office of Divisional Railway Manager, Dhanbad or anywhere else at any time. Tender will be decided purely on the basis of documents available/attached with the E-tender irrespective of whether tenderer is working contractor or new. However Railway may ask clarification with respect to document available/attached with the E-tender, if required.
In case, submission of Bid Security in the form of Bank Guarantee, the original Bank Guarantee should be delivered to COS/Bill&Tender/Dhanbad (Official Nominated) before closing date for submission of bids. (i.e. excluding the last date of submission of bids) as per Para 3 (ii) of Sl. No.13 (Bid Security) of the tender document.
DHN:-Repairs Renovation of filter house at KTH & KDS and other related works for water supply system under SSE/W/KTH.
363-DHN-2025-26~ECR
363-DHN-2025-26
Open
Works - General
9 Months
Dhanbad, Jharkhand
₹0
₹1.1 L
13 Apr 2026
20 Mar 2026
30 Mar 2026
106 items across 2 schedules · ₹89,650 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | 4km | cum | 50 | 199.77 | 9,988.5 |
| 2 | Cost of carriage including loading, unloading & stacking for first 50 metres | cum | 20 | 187.24 | 3,744.8 |
| 3 | All kinds of soil. | cum | 1250 | 286.85 | 3,58,562.5 |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 120 | 253.95 | 30,474 |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 5 | 2,161.2 | 10,806 |
| 6 | All kinds of soil | Sqm | 500 | 28.15 | 14,075 |
| 7 | 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 30 | 7,783.65 | 2,33,509.5 |
| 8 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 10 | 7,365.15 | 73,651.5 |
| 9 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 20 | 6,833.4 | 1,36,668 |
| 10 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 20 | 8,364.2 | 1,67,284 |
| 11 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 10 | 10,185.05 | 1,01,850.5 |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 120 | 804.25 | 96,510 |
| 13 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 5 | 18,644.6 | 93,223 |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 1 | 8,683.8 | 8,683.8 |
| 15 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 2 | 10,306.2 | 20,612.4 |
| 16 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 50 | 6,882 | 3,44,100 |
| 17 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 25 | 8,288.35 | 2,07,208.75 |
| 18 | Cement mortar 1:3 (1 cement : 3 coarse sand) | Sqm | 20 | 862.9 | 17,258 |
| 19 | Cement mortar 1:3 (1 cement :3 coarse sand) | Sqm | 50 | 1,043.1 | 52,155 |
| 20 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 20 | 1,063.45 | 21,269 |
| 21 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. | Sqm | 10 | 4,474.2 | 44,742 |
| 22 | Sal wood | cum | .1 | 1,06,720.85 | 10,672.09 |
| 23 | Fixed to openings /wooden frames with rawl plugs screws etc. | Kg | 1500 | 197.7 | 2,96,550 |
| 24 | 250x10 mm | Each | 10 | 374.35 | 3,743.5 |
| 25 | 150x10 mm | Each | 10 | 232.3 | 2,323 |
| 26 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 1 | 1,025.65 | 1,025.65 |
| 27 | 125 mm | Each | 20 | 226.5 | 4,530 |
| 28 | 100x10 mm | Each | 10 | 58.65 | 586.5 |
| 29 | 125 mm | Each | 10 | 60.05 | 600.5 |
| 30 | 100 mm | Each | 10 | 53.25 | 532.5 |
| 31 | 200 mm | Each | 10 | 153.15 | 1,531.5 |
| 32 | Using flats 30x6mm for diagonal braces and central cross piece | Sqm | 8 | 4,615.15 | 36,921.2 |
| 33 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 1000 | 142.3 | 1,42,300 |
| 34 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 350 | 612.25 | 2,14,287.5 |
| 35 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In- charge. | Kg | 200 | 103.7 | 20,740 |
| 36 | 40 mm thick with 20 mm nominal size stone aggregate | Sqm | 150 | 545 | 81,750 |
| 37 | Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. | cum | 10 | 7,958.65 | 79,586.5 |
| 38 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 2 | 3,908.8 | 7,817.6 |
| 39 | 110 mm diameter | Metre | 20 | 319.75 | 6,395 |
| 40 | 110 mm bend | Each | 6 | 132 | 792 |
| 41 | 110 mm Shoe | Each | 4 | 115.95 | 463.8 |
| 42 | 110 mm | Each | 12 | 309.5 | 3,714 |
| 43 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 200 | 671.55 | 1,34,310 |
| 44 | Ridges plain (500 - 600mm) | Metre | 25 | 450.6 | 11,265 |
| 45 | Gutter (600 mm over all girth) | Metre | 20 | 1,110.6 | 22,212 |
| 46 | 1:4 (1 cement: 4 fine sand) | Sqm | 350 | 294.85 | 1,03,197.5 |
| 47 | 12 mm cement plaster | Sqm | 200 | 386.55 | 77,310 |
| 48 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 350 | 214.3 | 75,005 |
| 49 | Flush / Ruled/ Struck or weathered pointing | Sqm | 100 | 214.4 | 21,440 |
| 50 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | Sqm | 2100 | 162.35 | 3,40,935 |
| 51 | Two coats | Sqm | 350 | 90.05 | 31,517.5 |
| 52 | One or more coats on old work | Sqm | 250 | 86.55 | 21,637.5 |
| 53 | Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. | Sqm | 600 | 94.15 | 56,490 |
| 54 | With cement mortar 1:4 (1cement: 4 coarse sand) | Sqm | 20 | 478 | 9,560 |
| 55 | Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge. | Sqm | 500 | 71.3 | 35,650 |
| 56 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | cum | 20 | 2,007.1 | 40,142 |
| 57 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 5 | 2,928.1 | 14,640.5 |
| 58 | In cement mortar | cum | 20 | 1,698.45 | 33,969 |
| 59 | Of area 3 sq. metres and below | Each | 10 | 302.7 | 3,027 |
| 60 | For thickness of tiles 10 mm to 25 mm | Sqm | 120 | 60.5 | 7,260 |
| 61 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Sqm | 120 | 45.05 | 5,406 |
| 62 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in- charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 100 | 219.35 | 21,935 |
| 63 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 1 | 5,781.35 | 5,781.35 |
| 64 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 1 | 5,540.55 | 5,540.55 |
| 65 | Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern | Each | 1 | 15,115.4 | 15,115.4 |
| 66 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap | Each | 2 | 1,913.75 | 3,827.5 |
| 67 | 10 litre capacity - White | Each | 2 | 1,023.05 | 2,046.1 |
| 68 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. | Each | 5 | 886.25 | 4,431.25 |
| 69 | 32 mm dia | Each | 3 | 90.95 | 272.85 |
| 70 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 2 | 1,411.15 | 2,822.3 |
| 71 | Rectangular shape 1500x450 mm | Each | 2 | 1,817.2 | 3,634.4 |
| 72 | Sand cast iron S&S pipe as per IS: 1729 | Metre | 30 | 1,018.05 | 30,541.5 |
| 73 | 100 mm dia pipe | Each | 20 | 163.45 | 3,269 |
| 74 | Sand cast iron S&S as per IS - 1729 | Each | 4 | 530.7 | 2,122.8 |
| 75 | Sand cast iron S&S as per IS - 1729 | Each | 4 | 412.95 | 1,651.8 |
| 76 | 20 mm nominal dia Pipes | Metre | 50 | 513.75 | 25,687.5 |
| 77 | 15 mm dia nominal bore | Metre | 20 | 267.5 | 5,350 |
| 78 | 25 mm dia nominal bore | Metre | 50 | 417.95 | 20,897.5 |
| 79 | 40 mm dia nominal bore | Metre | 25 | 558.35 | 13,958.75 |
| 80 | 50 mm dia nominal bore | Metre | 60 | 654.2 | 39,252 |
| 81 | 80 mm dia nominal bore | Metre | 60 | 919.1 | 55,146 |
| 82 | 25 to 40 mm nominal bore | Each | 20 | 757.1 | 15,142 |
| 83 | 50 to 80 mm nominal bore | Each | 20 | 1,513.7 | 30,274 |
| 84 | 15 mm nominal bore | Each | 12 | 303.85 | 3,646.2 |
| 85 | 15 mm nominal bore | Each | 12 | 303.85 | 3,646.2 |
| 86 | 25 mm nominal bore | Each | 2 | 532.35 | 1,064.7 |
| 87 | 15 mm nominal bore | Each | 4 | 348.85 | 1,395.4 |
| 88 | 80 mm diameter pipe | Each | 4 | 182.85 | 731.4 |
| 89 | 100 mm diameter pipe | Each | 12 | 284.75 | 3,417 |
| 90 | 150 mm diameter pipe | Each | 6 | 343.55 | 2,061.3 |
| 91 | 200 mm diameter pipe | Each | 2 | 377 | 754 |
| 92 | Class II | Each | 20 | 4,500.25 | 90,005 |
| 93 | Class II | Each | 6 | 6,661.8 | 39,970.8 |
| 94 | Class II | Each | 3 | 13,512.6 | 40,537.8 |
| 95 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Litre | 3000 | 9.7 | 29,100 |
| 96 | 15 mm nominal bore | Each | 4 | 708.4 | 2,833.6 |
| 97 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. | Each | 5 | 61.7 | 308.5 |
| 98 | 100 mm nominal dia | Each | 4 | 33.2 | 132.8 |
| 99 | 15 mm nominal bore with 45 cm length | Each | 4 | 107.9 | 431.6 |
| 100 | Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | Kg | 300 | 474.7 | 1,42,410 |
| 101 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm | 50 | 1,325.55 | 66,277.5 |
| 102 | Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) | cum | 5 | 7,510.75 | 37,553.75 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .