Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹9.9 L
EMD Value
₹19,800
Closing Date
23 Feb 2026, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
CNW
1 condition
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Repair of Center Sill crack in BTPN wagons at KJGY ROH Depot
116S-WC-13-MC-4-2025-26
116S-WC-13-MC-4-2025-26
Open
Works - General
3 Months
Ambala, Haryana
₹0
₹19,800
23 Feb 2026
14 Feb 2026
13 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 9,91,200 | ||
| Keep the wagon stable on track with the help of wooden wedge blocks. Remove the rivets (Cold Cutting) of ladder provided at different locations of barrel and under frame. Detach the ladder from wagon from both sides, if required for keeping the barrel stable after removal from under frame. | — | — | — | 1,06,200 | |
| Remove all the rivets (preferably by cold cutting) between cradle and anchoring Tee, without any damage to hole in anchoring Tee & cradle and detach the barrel from wagon. | — | — | — | 70,800 | |
| Lift the under frame through lifting pad and run out bogies by placing under frame on trestles at suitable locations. | — | — | — | 70,800 | |
| Cut and remove the Centre pivot top including Centre pivot packing, bolster bottom gusset and support plate, if required for repairing of Centre sill (for particular locations i.e. near the bolster location) | — | — | — | 35,400 | |
| IF CRACK IS ON THE FLANGE OF CENTRE SILL Clean the crack area thoroughly because containment of surface can mask the defects. Ensure the extent of crack by Dye Penetrate test. Since Dye Penetrate test does not reflect the depth of crack, carry out this test from both side of the Centre sill to ensure the propagation of crack on other side of Centre sill. Make 10 mm dia. hole, on both sides of the crack to arrest the crack. Gouge the crack completely by making bevel formation at crack position, preferably from sole bar side. Preheat the crack and nearby area up to 300 to 400 degree centigrade to avoid regeneration of any new crack in the area. Proper weld the crack in down hand position with suitable electrode as per Spec. No. G-72 (latest) and ground flush. Back gouge the crack from back side for sealing run, if crack has propagated through its entire depth, if required for fitment of other part. change the existing Item no -15 of RDSO Drg. WD-86061- S-54 (5 thk.) by Item no. 3 (10 thk) of RDSO Drg. No. WD-08097-S-1. IF CRACK FOUND ON THE WEB OF CENTER SILL it can be repaired without removing the barrel from under frame. | — | — | — | 2,83,200 | |
| Carry out the dye penetrate test to ensure the quality of weld joint, after thorough cleaning. | — | — | — | 17,700 | |
| Place a stiffener plate of 10 mm thickness of suitable size, after preheating the area, from back side (i.e. in between Centre sill) and all rounds weld it. As shown as Item No. 5 of RDSO Drg. No. WD-08097-S-1. | — | — | — | 35,400 | |
| If Centre sill repair is carried out at Bolster location, reduce the size of 12 thick support plate (provided in between Centre sill at bolster location above the Centre pivot) to accommodate the stiffener plate. Replace the old top stiffener plate by a plate of 490x695x12 (item no.-4 RDSO Drg. No. WD-08097-S-1. | — | — | — | 35,400 | |
| Weld an addition stiffener outside the crack area of Centre sill towards sole bar side (with a pocket to observe any new development in the crack area) | — | — | — | 17,700 | |
| Modify the wagon by providing additional stiffener plate as suggested by this office letter no. MW/BTPN dated 07.07.2009, if not modified previously | — | — | — | 17,700 | |
| Again weld all the brackets, if detached. After crack repairing and removing under frame from manipulator, place the barrel over cradle and rivets the barrel with cradle | — | — | — | 2,83,200 | |
| Provide all the subassemblies/components/accessories in the wagon which are detached for repairing purpose. All welding work to be done in down preferably down hand welding. | — | — | — | 17,700 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
biddocument.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .