Special repairs to building No E-03 at MH Cannanore under AGE(I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for structural steel work in tubular trusses including special shaped washer, two coats of synthetic enamel paint over a coat of primer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

All as per item No 5 here in before but except timber all as specified and directed. Note : Serviceable timber obtained from item No 3 shall be reused.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed.

S & F PVC (SWR) pipe 180 mm bore as in half round gutters including drop ends/stop end suitable for 180 mm half round valley gutter and fixing with MS/PVC clamps suitable for steel sheet roof complete all as specified and as directed.

S&F 75 mm PVC (SWR) downtake pipes single socketed, in any length with solvent joints, fixed to wall with suitable clamps complete all as specified and as directed.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3 kg cement per Sqm all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 10mm to 12mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 300x200x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Dismantling wall or ceiling boards any type (fibre, pulp, insulation or insulation boards, slabs, blankets), any thickness, including cover fillets all as specified and as directed

S & F for anodized aluminium snap grid frame work as in clause No. 10.38 of MES Schedule Part I for false ceiling of size 605 mm x 605mm with supporting hanger comprising of 6 mm MS rod / GI flat 40x3mm, ‘J’ bolt with necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid complete all as specified and directed

M & L for 4mm thick High Pressure Steam Cured ( HPSC ) non asbestos fibre cement building boards fixed or laid/inserted to aluminium snap grid frame work with screws all as specified and directed.

M&L for preparation of new cement concrete ceiling surfaces or non AC ceiling board surfaces and applying three coats of white wash all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:4) on concrete or brick masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone brick masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for complete removal of existing treatment on surfaces of wall and applying two coats of acrylic wall putty for making the surface smooth and even including sanding each layer to receive next new layer and applying one coat of wall primer(water thinnable/solvent thinnable), applying two coats of oil emulsion distemper by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for preparation of new surfaces of walls and applying two coats of acrylic wall putty for making the surface smooth and even including sanding each layer to receive next new layer and applying one coat of wall primer(water thinnable/solvent thinnable), applying two coats of oil emulsion distemper by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for complete removal of existing treatment on external wall surfaces by wire brushing, crack filling and bio-wash to fight microbial growth and applying one coat of exterior wall care putty for making the surface smooth and even including sanding each layer, one coat of exterior wall primer and two coats of exterior emulsion anti-algai weather proof paint of Make : Asian Paints Apex Ultima or equivalent in Berger or Dulux all as specified and as directed.

M&L for Preparing newly plastered surfaces on external walls and applying one coat of exterior wall care putty for making the surface smooth and even including sanding each layer, one coat of exterior wall primer and two coats of exterior emulsion anti-algai weather proof paint of Make : Asian Paints Apex Ultima or equivalent of Berger or Dulux all as specified and as directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F 125mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

Taking down shutters of any description exec 1 sqm but n exc 2sqm, easing and adjusting and refixing/renewal of builders hardware including renewal of screws and refixing the shutter in same opening all as specified and directed.

Taking down shutters of any description n exec 1 sqm all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S & F 2nd class hard wood plain fillets, square, rectangular in section clean sawn secured with nails exc 6 and n.exc 13 Sqcm in section all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15 mm bore UPVC (ASTM) pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC (ASTM) pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

Dismantling drain pipes (Cast iron/ RCC) set in cement mortar internal dia of pipes upto100 mm and removing debris outside MD land complete all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

S&F 75 mm bore, PVC (SWR) bend with access door any radius all as specified and directed

S&F in repair Vitreous China Wash basin, white, flat back, size 580 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand and fixing of waste pipe etc complete all as specified and directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F in repairs 15mm dia pillar taps fancy type Chromium plated screwed down high pressure with or without lettered 'Hotor Cold' with long screwed shanks and fly nuts ,screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15 mm dia stop cock cast copper alloy screw down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as directed by Engr-in-Charge.

S&F Brass Chromium plated Bib taps fancy type with flange 15 mm dia bore type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as fixed in repairs all as specified and directed by Engineer-in-Charge.

Supply and fix PVC connecton 45cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repair for PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including flush pipe all as specified and directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

All as per item No 55 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No 55 here in before but for One 3 Pin, 5 Amps socket on same board with other switches all as specified and directed.

All as per item No. 55 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 4Sqmm unsheathed PVC insulated copper conductor FRLS cable including 4 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified.

Cutting chases on wall of width 30mm and depth 35mm for concealing PVC conduit 20/25mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface and treated with existing treatment such as white wash/OBD/cement base paint etc complete all as directed.

All as per item No 59 here in before but width 50mm all as directed.

All as per item No 59 here in before but width 75mm dia all as directed.

S&F modular switches one way, single pole, 6 amp, 240V, one module connecting up electrically complete all as specified and directed.

S&F modular switches one way, single pole, 16 amp, 240V, one module connecting up electrically complete all as specified and directed.

S&F modular bell push, flush type, 6 amp, 240V, one module connecting up electrically complete all as specified and directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S&F modular socket, 2-in-1, 5 pin, 6 amp, 240V,connecting up electrically all as specified and directed.

S&F modular socket, 2-in-1, 5 pin, 6&16 amp, 240V, connecting up electrically all as specified and directed.

S& F calling bell electric AC 240V, single pole, ding dong type and connecting up electrically all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for two module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for three module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for four module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for six module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for eight module all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 8 way with 200 Amps bus bar, 415 Volt, double door type, fixed/flushed on wall including electrically connecting up and taking down old unserviceable DB complete all as specified and directed.

S & F MCB SPN, 10KA 'C' series 240 Volt, 32Amps including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SP, 10KA 'C' series, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with polycarbonate, environmental friendly, energy efficient ready to use pack of E-LITE LED pride plus Neo of 20 W LED 6500K, model LHEXACP7IN1W020 of Havells or equivalent of PHILIPS of Crompton Greaves, with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with polycarbonate, environmental friendly, energy efficient ready to use pack of E-LITE LED pride plus Neo of 10 W LED 6500K, model LHEXBTP7IN1W009 of Havells or or of SSK-T-5 12W of Syskaequivalant of Bajaj/Crompton Greaves with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings nd electrically connecting up all as directed.

M & L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note :- Rate quoted shall deem to include for GI earth and GI pipe lead upto 7.5m length.

S&F in repalacement LED ball type lamp 10watt all as directed.

M&L for sub main wiring with two runs of single core 4 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVC all accessories such as bend,elbow,socket,tee saddles etc fixed concealed to wall / fixed to ceiling etc including 4 Sq mm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 3 runs of 4 Sq mm copper cable and one run of PVC conduit will be measured as one length.

S&F modular 5 step fan regulator, full rotation, 200W, SP, 230V onnecting up electricallyall as specified and directed.

S & F sheet metal enclosure factory madewith socket single pole and neutral two pin with earth complete with SP MCB of 20amp with plug top fixed/flushed on wall including electrically connecting up complete all as specified and directed.

Taking down carefully ceiling fan with rod from ceiling / roof and refixing the same after repairs such as servicing, greasing, replacement of ceiling fan down rod of suitable length, clamps, nuts, washers, rubber bushes, safety pin etc as required and applying one coat of white synthetic enamel paint and writing of MES No complete including connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan , test and commissioning all as specified and directed. Note : Rewinding and replacement of capacitor & bearing shall be measured and paid seperately.

Rewinding of ceiling fan 1200 mm sweep any type and make, cutting and removing burnt winding wire without damaging stator, removing old insulation of polyester paper, re-winding fan motor with super enameled copper wire of same gauge/dia with correct number of turns for auxiliary and main winding, varnishing, baking, soldering new lead of twin core multi-stranded copper conductor cable of size 23/0.0076, assembling, replacement of capacitor 2.5mfd capacitorand ball bearing, re-fixing, testing and commissioning complete all as specified and directed.

S&F GI earth continuity wire of 4 sqmm dia drawn through with and including 15mm dia GI pipe light grade complete all as directed.

M & L for clamps made out of flat iron (duly painted with enamel paint over red oxide primer ) made of 40mmx 4mm duly bolted with double nuts and washer on existing wooden beams of approx size 300mm x 200mm with and inclusive of fan down rod of 1.5mtr to 2 mtr length duly fitted on MS clamps with bolts, nuts with safety pin and twin core twisted multi stranded copper flexible wire of size 23 / 0.0076 from ceiling rose to fan complete all as specified and as directed.

Preparation of old wooden surfaces of any description over 10 cm in width or girth and applying a coat of synthetic enamel paint all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with ss wire staples all as specified and as directed.

JEETH CONSTRUCTION

Safarulla padikkal

VIJAY ENTERPRISES