HT and LT Electrification works including supply of all Materials Labor and services for providing power supply for the establishment of Common Facility Center

HIGH TENSION TIME OF DAY METER (HT TOD METER)

Installation and commissioning charges for the above Item No.1

11KV LOAD BREAK SWITCH WITH HIGH TENSION METERING (INDOOR)

Installation, Testing and Commissioning charges for the above Item No.3

Supply of, 3C x 300 mm², 11KV XLPE armoured Aluminium UG cable as per BIS 1255/1983.

Laying of 3C x 300 mm², 11KV XLPE armoured Aluminium UG cable in ground,in built up trenches, walls, pulling through pipes including all minor civil works, such as laying of sand and brick, chipping of floors etc.,as per BIS 1255/1983. (Trenching works will be uder the scope of client)

Outdoor end termination kit for 3C x 300mm²

Installation of cable outdoor end termination using push on/heat shrinkable cable termination kit, Aluminium crimping lugs, gland earthing of adequate size etc., complete for following 11kV XLPE armoured Aluminium UG cable.

Indoor end termination kit for 3C x 300mm²

Installation of Indoor end termination using push on/heat shrinkable cable termination kit, Aluminium crimping lugs, gland earthing of adequate size etc., complete for following 11kV XLPE armoured Aluminium UG cable.

500KVA INDOOR OIL COOLED TRANSFORMER WITH ON LOAD TAP CHANGER

Installation, Testing and commissioning charges for the above Item No.11

Supply and Testing (From Accredited Testing Lab) of Neutral CT (Ratio:150/5A, CL:5P10, 5VA) with suitable metal enclosure for earth fault relay (Statutory fee payable to KSEB will be paid by the owner.)

Installation charges for the above Item No.13

MSB (MAIN SWITCH BOARD) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.15

MCC-1 (MOTOR CONTROL CENTER-1) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.17

MCC-2 (MOTOR CONTROL CENTER-2)Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.19

MCC-3 (MOTOR CONTROL CENTER-3) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.21

MCC-4 (MOTOR CONTROL CENTER-4) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.23

APFC (AUTOMATIC POWER FACTOR CONTROL) PANEL Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.25

GSB (GENERATOR SWITCH BOARD) :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.27

GSSB (GENERATOR SUB SWITCH BOARD) :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.29

SSB (SUB SWITCH BOARD) - UTILITIES :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.31

LSB (LIGHTING SWITCH BOARD) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.33

PSB (POWER SWITCH BOARD) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.35

WCP(WATER CONTROL PANEL)Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.37

FCP (FIRE CONTROL PANEL) Consists of :(Ref: The Attached Tender doc, SECTION IV –SCHEDULE OF REQUIREMENTS)

Installation, Testing and commissioning charges for the above Item No.39

UPS (UNINTERRUPTABLE POWER SUPPLY)

Installation, Testing and commissioning charges for the above Item No.41

8way VTPN MCCB DB

Installation Testing and Commissioning charges for the above Item No.43

4way VTPN MCB DB

Installation Testing and Commissioning charges for the above Item No.45

8way TPN MCB DB

Installation Testing and Commissioning charges for the above Item No.47

6way TPN MCB DB

Installation Testing and Commissioning charges for the above Item No.49

4way TPN MCB DB

Installation Testing and Commissioning charges for the above Item No.51

8way SPN MCB DB

Installation Testing and Commissioning charges for the above Item No.53

12way SPN MCB DB

Installation Testing and Commissioning charges for the above Item No.55

16way SPN MCB DB

Installation Testing and Commissioning charges for the above Item No.57

6-32 SP MCB 'C' Series

Installation Testing and Commissioning charges for the above Item No.59

6-32 TP MCB 'C' Series

Installation Testing and Commissioning charges for the above Item No.61

32-63 TP MCB 'C' Series

Installation Testing and Commissioning charges for the above Item No.63

63A FP RCBO 30mA

Installation Testing and Commissioning charges for the above Item No.65

40A FP RCBO 30mA

Installation Testing and Commissioning charges for the above Item No.67

32A FP RCBO 30mA

Installation Testing and Commissioning charges for the above Item No.69

100A TPN ISO with star-delta starter for 50 HP motor with suitable O/L relay settings using ON- OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.71

63A TPN ISO with star-delta starter for 20 HP motor with suitable O/L relay settings using ON- OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.73

DOL starter for 5 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.75

DOL starter for 3 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.77

DOL starter for 2 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.79

DOL starter for 1.5 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.81

DOL starter for 1 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.83

DOL starter for 0.5 HP motor with suitable O/L relay settings using ON-OFF push button with enclosure

Installation Testing and Commissioning charges for the above Item No.85

125A 4P ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.87

100A 4P ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.89

3 ½ x 400mm² AYFY Cable Cable

Laying charges for the above Item No.91

3 ½ x 240mm² AYFY Cable

Laying charges for the above Item No.93

3 ½ x 185mm² AYFY Cable

Laying charges for the above Item No.95

3 ½ x 150mm² AYFY Cable

Laying charges for the above Item No.97

3 ½ x 120mm² AYFY Cable

Laying charges for the above Item No.99

3 ½ x 95mm² AYFY Cable

Laying charges for the above Item No.101

3 ½ x 70mm² AYFY Cable

Laying charges for the above Item No.103

3 ½ x 50mm² AYFY Cable

Laying charges for the above Item No.105

3 ½ x 35mm² AYFY Cable

Laying charges for the above Item No.107

4 x 25mm² AYFY Cable

Laying charges for the above Item No.109

4 x 16mm² AYFY Cable

Laying charges for the above Item No.111

4 x 10mm² AYFY Cable

Laying charges for the above Item No.113

4 x 6mm² AYFY Cable

Laying charges for the above Item No.115

3C x 2.5mm² Armoured Copper UG Cable

Laying charges for the above Item No.117

3C x 4mm² Armoured Copper UG Cable

Laying charges for the above Item No.119

12C x 1.5mm² Armoured Copper UG Cable

Laying charges for the above Item No.121

6C x 1.5mm² Armoured Copper UG Cable

Laying charges for the above Item No.123

For 3 ½ x 400mm² AYFY Cable

Installation charges for the above Item No.125

For 3 ½ x 240mm² AYFY Cable

Installation charges for the above Item No.127

For 3 ½ x 185mm² AYFY Cable

Installation charges for the above Item No.129

For 3 ½ x 150mm² AYFY Cable

Installation charges for the above Item No.131

For 3 ½ x 120mm² AYFY Cable

Installation charges for the above Item No.133

For 3 ½ x 95mm² AYFY Cable

Installation charges for the above Item No.135

For 3 ½ x 70mm² AYFY Cable

Installation charges for the above Item No.137

For 3 ½ x 50mm² AYFY Cable

Installation charges for the above Item No.139

For 3 ½ x 35mm² AYFY Cable

Installation charges for the above Item No.141

For 4 x 25mm² AYFY Cable

Installation charges for the above Item No.143

For 4 x 16mm² AYFY Cable

Installation charges for the above Item No.145

For 4 x 10mm² AYFY Cable

Installation charges for the above Item No.147

For 4 x 6mm² AYFY Cable

Installation charges for the above Item No.149

For 3C x 2.5mm² Armoured Copper UG Cable

Installation charges for the above Item No.151

For 3C x 4mm² Armoured Copper UG Cable

Installation charges for the above Item No.153

For 12C x 1.5mm² Armoured Copper UG Cable

Installation charges for the above Item No.155

For 6C x 1.5mm² Armoured Copper UG Cable

Installation charges for the above Item No.157

For 1Cx16mm² Copper Flexible Wire (PE)

Installation charges for the above Item No.159

For 1Cx10mm² Copper Flexible Wire (PE)

Installation charges for the above Item No.161

PLATE EARTH STATIONS Supply of efficient plate earthing using 1200 x 1200 x 12.3 mm Cast Iron earth electrode with necessary earth pit pipe connection including filling the pit with charcoal salt etc. cement concrete or equivalent construction, etc. complete as required including excavation of earth pit.(Construction of Earth chamber will be under the scope of client)

Installation & Testing charges for the above Item No.163

Supply of efficient plate earthing using 600 x 600 x 6.3 mm Copper Plate earth electrode with necessary earth pit pipe connection including filling the pit with charcoal salt etc. cement concrete or equivalent construction, etc. complete as required including excavation of earth pit. (Construction of Earth chamber will be under the scope of client)

Installation & Testing charges for the above Item No.165

Supply of 38 mm dia 2.5 m long GI pipe earth stations,filling salt,sand and charcoal, construction of earth chamber and covering with heavy duty cast iron hinged to Cast Iron Frame, including excavation of earth pit.(Construction of Earth chamber will be under the scope of client)

Installation & Testing charges for the above Item No.167

Copper flat 25x 6 mm

Laying charges for the above Item No.169

Copper flat 25 x 3 mm

Laying charges for the above Item No.171

No.6 SWG CU

Laying charges for the above Item No.173

No.8 SWG CU

Laying charges for the above Item No.175

No.10 SWG CU

Laying charges for the above Item No.177

16mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.179

10mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.181

6mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.183

One light/exhaust fan controlled by 6A switch.

Installation, Testing & commissioning charges for the above Item No.185

Two light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.187

Three light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.189

Four light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.191

Five light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.193

Six light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.195

Ten light controlled by 6 A switch.

Installation, Testing & commissioning charges for the above Item No.197

4 lights controlled by 10A SP MCB

Installation, Testing & commissioning charges for the above Item No.199

5 lights controlled by 10A SP MCB

Installation, Testing & commissioning charges for the above Item No.201

6 lights controlled by 10A SP MCB

Installation, Testing & commissioning charges for the above Item No.203

7 lights controlled by 10A SP MCB

Installation, Testing & commissioning charges for the above Item No.205

8 lights controlled by 10A SP MCB

Installation, Testing & commissioning charges for the above Item No.207

Ceiling fan point controlled by 6A switch and electronic fan regulator step type

Installation, Testing & commissioning charges for the above Item No.209

2R x 1.5mm² (P&N) + 1R x 1.5mm² (E)

Laying charges for the above Item No.211

2R x 2.5mm² (P&N) + 1R x 1.5mm² (E)

Laying charges for the above Item No.213

2R x 4mm² (P&N) + 1R x 2.5mm² (E)

Laying charges for the above Item No..215

6A Socket outlet (Combined)

Installation, Testing & commissioning charges for the above Item No.217

6A Socket outlet (Indepedent)

Installation, Testing & commissioning charges for the above Item No.219

16A Socket & Switch

Installation, Testing & commissioning charges for the above Item No.221

32A DP switch for AC

Installation, Testing & commissioning charges for the above Item No.223

20A Metal Clad Plug & Socket 2P+E, 240V, IP44

Installation, Testing & commissioning charges for the above Item No.225

32A Metal Clad Plug & Socket - 3P+N+E, 415V, IP44

Installation, Testing & commissioning charges for the above Item No.227

8Way PVC Enclosure IP55/56

Installation, Testing & commissioning charges for the above Item No.229

4P Metal Enclosure for MCB

Installation, Testing & commissioning charges for the above Item No.231

2pair 0.5mm² Telephone Cable

Laying charges for the above Item No.233

Single

Installation, Testing & commissioning charges for the above Item No.235

Installation, Testing & commissioning charges for the above Item No.237

Supply of 10 pair telephone connectors on suitable stands and providing terminations with ferrule identification of terminals

Installation, Testing & commissioning charges for the above Item No.239

Supply of all materials for network points using CAT6 UTP LSZH Cable in 20 mm ISI PVC pipe concealed / fixed cable trays.

Laying charges for the above Item No.241

Single

Installation, Testing & commissioning charges for the above Item No.243

Supply of 22U Rack with 2 Nos 12 PDU Socket, Forced Ventilation Fan with locking facility with all mounting brackets and cable management accessories

Installation, Testing & commissioning charges for the above Item No.245

Supply of WIFI Access Points Ceiling Mounted with concurrent dual band with WIFI 6 capabilities 802.11ac with internal antenna with OFDMA and MU-MIMO for enhanced multi-user

Installation, Testing & commissioning charges for the above Item No.247

Supply of 24 Port 10/100/1000 PoE Managed switch with 2 SFP ports

Installation, Testing & commissioning charges for the above Item No.249

Supply of 24 Port 10/100/1000 Non PoE Fully managed switch with layer2 capabilities With 4 SFP ports uplinks

Installation, Testing & commissioning charges for the above Item No.251

Supply of 24 Port Loaded Patch Panel fully loaded

Installation, Testing & commissioning charges for the above Item No.253

PUBLIC ADDRESS SYSTEM:-Supply of all materials for speaker points using 2 run 1.5 sq mm PVC insulated Copper wire in 20 mm ISI PVC conduit concealed/ fixed cable trays above false ceiling.

Laying charges for the above Item No.255

Supply of 6W,100V, 60-15000Hz,90dB, Ceiling Speaker

Installation, Testing & commissioning charges for the above Item No.257

Supply of 120W Mixer Amplifier with USB / Bluetooth Mwedia Player

Installation and commissioning charges for the above Item No.259

CCTV:-Supply of all materials for camera points using CAT6 UTP LSZH Cable in 20 mm ISI PVC pipe concealed / fixed cable trays.

Laying charges for the above Item No.261

Supply of 4MP,IR, IP Dome Camera 3.6mm Lens, PoE, H265 WITH WDR

Installation, Testing & commissioning charges for the above Item No.263

Supply of 32 channel NVR, realtime recording,H265 with , USB 3, HDMI 4K, VGA, with Minimum 4 HDD port with capacity of 24 TB memory handling capacity.

Installation, Testing & commissioning charges for the above Item No.265

Supply of 6 TB SURVEILLANCE HARDDISK , SATA, 6Gb/s, 128 Cache, 7200 RPM,

Installation, Testing & commissioning charges for the above Item No.267

Supply of LED Monitor , Full HD high resolution color 27" Monitor

Installation & Testing charges for the above Item No.269

Supply of Patch cord CAT6 RJ45 1Mtr

Installation & Testing charges for the above Item No.271

Supply of EPABX System Supports up to 240 analog extensions,with inbuilt SIP trunk & IP card with 16 IP licences

Installation, Testing & commissioning charges for the above Item No.273

Supply of Operator console IP Phone with 60 one touch keys

Installation, Testing & commissioning charges for the above Item No.275

Supply of Basic Caller ID Phones

Installation, Testing & commissioning charges for the above Item No.277

LIGHTNING PROTECTION:- Supply of 1m Air termination Rod with accessories as per BIS/IEC -62305, Semi-hard (AlMgSiO5) Suitable for high wind load

Laying charges for the above Item No.279

Supply of Multipurpose connecting clamp. Meets the requirement of BIS/IEC 62305: semihard (AlMgSiO5) with 50 sq.mm cross sectional area

Installation charges for the above Item No.281

Supply of DOWN CONDUCTOR 8mm Solid AlMgSiO5 (Vertical Run). Meets the requirement of BIS/IEC 62305: semi-hard(AlMgSiO5) with 50 sq.mm cross sectional area

Laying charges for the above Item No.283

Supply of Conductor Holders for RCC(Vertical Run) at every 0.8m interval

Installation charges for the above Item No.285

Supply of Test Clamp suitable for connecting 25x6 mm solid GI Strip and 8mm solid Aluminium round conductor

Laying charges for the above Item No.287

Supply of GI Strip of 25x6mm thickness & Accessories for connecting between 8mm Aluminium round conductor and Earth electrode

Laying charges for the above Item No.289

Supply of GI Strip Holder of size suitable for 25x6mm thickness for fixing GI strip with Building.

Installation charges for the above Item No.291

EARTHING SYSTEM :Type A - Earth Pits : Supply of Earthing System comprises of 3m Long Cu Bonded Earth Electrode, Rod to Tape Clamp, 22.5Kg Earthing Compound & Earth Chamber. Earthing(Type A arrangement) as per BIS/IEC 62305 - 3

Installation & Testing charges for the above Item No.293

LED lights - 9W Recessed (Specifications : Round, 4000K CT, 80-100 Lumes/Watt, PF>0.9, THD <10%)

Installation Charges for the above Item No.295

High Bay lights -100W (Factory lighting - 6 Mtr Height from FFL) (Specifications : Round, 5700K -6500K CT, 110-150 Lumes/Watt, PF>0.95, THD <10%, Beam Angle 90%, IP65) with mounting accessories as required.

Installation Charges for the above Item No.297

LED Spot light - 3W (Specifications : Round, 3000K CT, 80-100 Lumes/Watt, PF>0.9, THD <10%)

Installation Charges for the above Item No.299

LED Flood light -100W (Specifications : Rectangular with Bracket, 5700K CT, 100-120 Lumes/Watt, PF>0.9, THD <10%, IP65)

Installation Charges for the above Item No.301

LED Flood light -50W (Specifications : Rectangular with Bracket, 5700K CT, 100-120 Lumes/Watt, PF>0.9, THD <10%, IP65)

Installation Charges for the above Item No.303

Wall Fan (Specifications : BLDC, 400mm Sweep, BEE Rating >3 Star and above, 230/240V)

Installation Charges for the above Item No.305

LED Tube lights -4 Feet (Specifications : 20W, Aluminium Body, 5700K CT, 100 Lumes/Watt, PF>0.9, THD <10%)

Installation Charges for the above Item No.307

LED Wall lights -Outdoor (Specifications : 4-9W, Metal / Aluminium Body, 3000K CT, 100 Lumes/Watt, PF>0.9, THD <10%, IP66)

Installation Charges for the above Item No.309

LED Spike lights -Outdoor (Specifications : 4-8W, Metal / Aluminium Body, 3000K CT, 100 Lumes/Watt, PF>0.9, THD <10%, IP66)

Installation Charges for the above Item No.311

LED Rope with Drives (Specifications : 9-12W/Mtr, 4000K CT, 100-110 Lumes/Watt, PF>0.9, THD <10%, IP-20 with suitable power supply)

Installation Charges for the above Item No.313

LED Bulkhead light fixture (Specifications : 7-9W, 4000K CT, 80-100 Lumes/Watt, PF>0.9, THD <10%)

Installation Charges for the above Item No.315

Street light post 9m long MS with single LED Lamp (Specifications : 36-40W, Aluminium body,Integrated LED Driver, 5700 CT, 80-100 Lumes/Watt, PF>0.9, THD <10%, IP66) including all connections with suitable connectors, breakers, mounting accessories as required without civil works

Installation Charges for the above Item No.317

LED Short bollard light fixtures (Specifications : 8-12W, Metal / Aluminium Body, 4000K CT, 100-120 Lumes/Watt, PF>0.9, THD <10%, IP66)

Installation Charges for the above Item No.319

1200 mm sweep, BEE Rating >3 Star and above and regulator friendly BLDC ceiling fan, complete with 300mm down rod, canopies, shackles, and blades working on 230/240V sigle pahse AC.

Installation Charges for the above Item No.321

Exhaust fan medium duty (Specifications : Metal body, 230mm Sweep, BEE Rating >3 Star and above, 230/240V)

Installation Charges for the above Item No.323

Surface mounted non maintained self contained LED luminaries with battery back up LED and sign label (Specifications : 2-6W, IP 20, Duration: 1 and 3 hours Back up, Ni-Cd or Ni-MH batteries)

Installation Charges for the above Item No.325

Flab/suspension mounting double sided self contained LED luminaires with emergency exit sign label including required battery backup (Specifications : 2-6W, IP 20, Duration: 1 and 3 hours Back up, Ni-Cd or Ni-MH batteries)

Installation Charges for the above Item No.327

CAPTIVE GENERATION:- 500KVA DG SET

Installation Testing & Commissioning charges for the above Item No.329

Supply of additional length of M.S.(B class medium grade) exhaust pipe line of 200mm DIA including hardware like flange,bends, bolt and nuts, gasket, support with heat resistant Aluminium painting, to building top for 500KVA DG set.

Installation charges for the above Item No.331

Supply and installation of exhaust pipe thermal insulation lagging with mineral wool as per IS 3677 / 1973 reinforced with chicken mesh and cladded with aluminium sheet of 26 SWG and thermal insulation.

Installation charges for the above Item No.333

Supply & Fabrication of MS structure for exhaust line i.e channel angles, plates, flat etc. as per design including anchor bolts / dash fasteners/ bolts & nuts/hardwares etc. as required complete with painting with one coat of primer and two coats of synthetic enamel paint as per approved shade for exhaust stack, exhaust pipe supports etc. complete in all respects.

Installation charges for the above Item No.335

300 x 50mm Size Ladder Type

Installation charges for the above Item No.337

200 x 50mm Size Ladder Type

Installation charges for the above Item No.339

150 x 50mm Size Ladder Type

Installation charges for the above Item No.341

200 x 50mm Size Perforated

Installation charges for the above Item No.343

Supply of Vertical /Horizontal type M.S. Cable Trays and cable supports fabricated out of M.S.Angles and M.S. flats with sufficient width and Spacing between successive cross members and supported at adequate spacing. The cable trays and supports shall be painted with 2coats of Zinc chromate primer and 2coats of enamel paint.

Installation charges for the above Item No.345

Supply of LT/High Tension danger boards.

Installation charges for the above Item No.347

Supply of shock treatment chart in glass with frame.

Installation charges for the above Item No.349

Supply of 11kV grade Synthetic Insulated mat 2 meter x 1 meter conforming to IS:15652:2006

Supply of 440V grade Synthetic Insulated mat 2 meter x 1 meter conforming to IS:15652:2006

Supply of DCP type fire extinguisher 5 Kg.

Installation charges for the above Item No.353

Supply of Electrical Grade rubber hand gloves suitable for operation of 11KV Switchgear.

Supply of 2nos fire buckets along with sand painted with enamel paint of red colour.

Installation charges for the above Item No.356

Supply of cable Trench covers using 6mm thick M S chequered plates for covering Trenches in Switchboard room / substation areas.

Installation charges for the above Item No.358

Supply of Cable route marker for High Tension UG Cable at every 10metre interval made of Cast Iron

Installation charges for the above Item No.360

Supply of 200x100mm IP67 weather proof out door cable termination box

Installation charges for the above Item No.362

Supply of emergency OFF trip push button with front Glass and painted in RED Colour.

Installation, Testing & Commissioning charges for the above Item No.364

40 mm PVC Pipe -6KG

Laying charges for the above Item No.366

20mm Medium Grade

Laying charges for the above Item No.368

LIAISON WORK :-Preparation of all documents and drawings for getting power alloction and service connection, submission of completion report and arranging inspection by KSEB and such other formalities and follow up action in KSEB (The statutary fees, deposits etc will be met by the client)

Arranging resistivity measurement, fault level calculation, preperation of necessary drawings,getting scheme approval, submission of completion report, arranging inspection, rectification of defects,getting energisation order and such other formalities of electrical inspectorate (All statutary fees will be met by client)

Annual maintenance charges for Transformer 500 KVA -first year after defect liability period

Annual maintenance charges for Transformer 500 KVA - second year after defect liability period

Annual maintenance charges for DG Set 500 KVA -first year after defect liability period

Annual maintenance charges for DG Set 500 KVA - second year after defect liability period

Annual maintenance charges for LBS panel-first year after defect liability period

Annual maintenance charges for LBS panel- second year after defect liability period

25A FP RCBO 30mA

Installation Testing and Commissioning charges for the above Item No.378

32A DP RCBO 30mA

Installation Testing and Commissioning charges for the above Item No.380

63A FP RCBO 100mA

Installation Testing and Commissioning charges for the above Item No.382

40A FP RCBO 100mA

Installation Testing and Commissioning charges for the above Item No.384

63A 4P ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.386

50A 4P ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.388

32A MCB 4P ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.390

16A 4P MCB ISO with Enclosure for Stabilizer Input of Equipments.

Installation Testing and Commissioning charges for the above Item No.392

3 x 6mm² AYFY Cable

Laying charges for the above Item No.394

3 x 4mm² AYFY Cable

Laying charges for the above Item No.396

3C x 1.5mm² Armoured Copper UG Cable

Laying charges for the above Item No.398

1Cx35mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.400

1Cx25mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.402

1Cx6mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.404

1Cx4mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.406

For 3 x 6mm² AYFY Cable

Installation and commissioning charges for the above Item No.408

For 3 x 4mm² AYFY Cable

Installation and commissioning charges for the above Item No.410

For 3C x 1.5mm² Armoured Copper UG Cable

Installation and commissioning charges for the above Item No.412

For 1Cx35mm² Copper Flexible Wire (PE)

Installation and commissioning charges for the above Item No.414

For 1Cx25mm² Copper Flexible Wire (PE)

Installation and commissioning charges for the above Item No.416

For 1Cx6mm² Copper Flexible Wire (PE)

Installation and commissioning charges for the above Item No.418

For 1Cx4mm² Copper Flexible Wire (PE)

Installation and commissioning charges for the above Item No.420

No.4 SWG CU

Laying charges for the above Item No.422

No.12 SWG CU

Laying charges for the above Item No.424

35mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.426

25mm² Copper Flexible Wire (PE)

Laying charges for the above Item No.428

Seven light controlled by 6 A switch.

Installation Testing and Commissioning charges for the above Item No.430

EigHigh Tension light controlled by 6 A switch.

Installation Testing and Commissioning charges for the above Item No.432

Nine light controlled by 6 A switch.

Installation Testing and Commissioning charges for the above Item No.434

8Way PVC Enclosure IP55/56

Installation charges for the above Item No.436

4P Metal Enclosure for MCB

Installation charges for the above Item No..438

Supply of 200mm DIA with 2mm thickness

Installation charges for the above Item No.440

Supply of 250mm DIA

Installation charges for the above Item No.442

450 x 50mm Size Ladder Type

Installation charges for the above Item No.444

150 x 50mm Size Perforated

Installation charges for the above Item No.446

125 x 50mm Size Perforated

Installation charges for the above Item No.448

100 x 50mm Size Perforated

Installation charges for the above Item No.450

75 x 50mm Size Perforated

Installation charges for the above Item No.452

50 x 50mm Size Perforated

Installation charges for the above Item No.454

25 mm PVC Pipe 6KG

Laying charges for the above Item No.456

50 mm PVC Pipe 10KG

Laying charges for the above Item No.458

100 mm PVC Pipe 10KG

Laying charges for the above Item No.460

25mm Medium Grade -6KG

Laying charges for the above Item No.462

32mm Medium Grade -6KG

Laying charges for the above Item No.464

50mm Medium Grade -6KG

Laying charges for the above Item No.466

Charges for earth excavation / trenching works including back filling

Supply of additional length of M.S.(B class medium grade) exhaust pipe line of 150mm DIA including hardware like flange,bends, bolt and nuts, gasket, support with heat resistant Aluminium painting, to building top for 500KVA DG set.

Installation charges for the above Item No.469