SPL REPAIR TO TOILET AND BATHROOMS IN BLDG NO. P-617 OF 14 INF DIV CAMP AND PROVN OF BAGGAGE ROOM FOR OTM BLDG NO. P-617, PATHWAY AND CONNECTED DRAIN NEAR GOVT MD ACCN BLDG NO P-93 TO P-98 AND P-103 APPROX LENGTH 70 MTR AND ADDN/ALTN TO SHAFT PORTION

Amount

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15 cm thickness ( below or above ground level ) and including removing unserviceable material,outside defence land complete all as specified and directed.

M & L 75 mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection / hardstanding , laid in panels, finished the top surfaces even and fair without using extra cement including filling the joints with mastic compound complete all as specified and directed

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including on the roof top/mumty/parapet/RCC chajjas/RCC water tank and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M & L RCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja / facia projection and the like complete all as specified and directed Note : The work is required to be carried out upto Second storey building. The cost of scaffolding shall be deemed to be included in the item. The contractor shall also make necessary safety arrangement for labour.

M & L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc and making good of disturbed portion complete all as specified and directed Note:- The work is required to be carried out at non-accessible shaft portion for triple/fourth storey .The contractor shall make arrangement of scoffolding,safety & security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items

M & L brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) ,complete all as specified and directed.

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) not exceeding 1.5 Sq.m each.Complete all as specified and directed

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) exe 1.5 Sqm but not exceeding 4.0 Sq.m each.Complete all as specified and directed.

M& L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F factory made single extruded WPC (Wood Polymer Composite) solid both side prelaminated decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed

S & F Pre coated Steel fixed type Window / ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated / Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams / Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The windows should be paneled with 5mm thick frosted glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick / concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Windows shall be provided with Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 125mm centre to centre bothways. Total Grill shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details in manufacturer‟s instructions complete all as specified and directed.

M & L butt hinges of mild steel medium weight cold rolled 100mm long and fixed with screws to timber frame work Complete all as specified and directed

S&F 200mm long SS barrel tower bolts all as specified

S&F 250mm SS sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate

S&F 150mm size SS handles all as specified and directed.

M & L for Mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 including Dismantling wrough iron or mild steel work any description not otherwise provided complete all as specified and directed

Taking down existing tar felt, PCC, Plastering from the roof surface and washing down & cleaning the surface with water and rubbish off the premises and finshing existing surface even & smooth and laying water proofing treatment to the Roof with single component, cold applied, water based Polyurethane modified acrylic dispersion with highly elastic and UV resistant water proofing treatment to the Roof @ 1.2kg/per sqm to confirms to ASTM D 6083- 97a with a density of 1.25 to 1.3kg/per ltr, having tensile strength of 1.5N/mm2, having elongation of 350°/o with solid content not less than 60% in 2 coats including self-priming bond coat of Advanced Latex plus mixed Water and Cement in 1:4:7 and sandwiching 40gsm Geo-textile between two coats. The finished cost to include surface preparation, making coving at Junction, Bore Packing, treatment of construction joints complete all as specified and directed.

M & L PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) mixed withliquid water proofing compound (as per manufacture direction and paid separately) over and incl one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete / mortar to old surface as per manufacturer direction and finishing the surface even and fair (without using extra cement) as in roof padding to receive roof treatment complete all as specified and directed. Note :- The work is required to be carried out at non-accessible roof for double storey . The contractor shall make arrangement of scoffolding,safety & security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items .

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises from MoD all as specified and directed.

M & L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square / rectangular) area of each tile exe 0.06 sqm but not exe 0.11 sqm, in floor etc incl 15mm thick screed bed in CM 1:6, Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II Grade-IV Complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by GE.

M & L for coloured glazed ceramic tiles of any design and pattern, 450 x 300 x 7 to 8 mm thick, as in dado etc incl 10 mm thick rendering in CM 1:4, Set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles Complete all as specified and directed.

M & L for 16 to 18 mm thick prepolished marble any colour (Udaipur green marble) (table rubbed and polished) as in stair case (tread & riser in single piece) steps, jambs, pillars, window cills, cooking platforms including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:6) complete all as specified and directed

M & L for rubber moulded vibro compacted coloured glossy finish cement concrete chequered tiles of size 30cm x 30cm x 20mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over and including 15mm thick screed bed in CM 1:6 and 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) complete all as specified and directed.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material outside of A 1 defence land complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete walls internal surfaces in CM 1:6 finished to even & smooth without using extra cement Complete all as specified and directed.

M & L plastering in 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed.

M & L rendering 5 mm thick in CM 1:3 in ceiling / Chhajja's finished even and smooth (without using extra cement). Complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of wall primer complete all as specified and directed

M&L for applying one coat of internal acrylic distemper of approved tint on walls on existing treatment and preparation of old plastered surface complete all as specified and directed

M&L for applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for preparation of old surface of wall , making the surface even and smooth and applying two coat of cement base paint on old decorated surfaces complete all as specified and as directed

M&L for applying two coats of cement base paint after preparation of newly plastered/concrete surfaces over primer on wall including complete all as specified and directed

M&L for preparation of newly plastered surface of ceiling including brooming down, making the surface even and smooth and applying three coat of white wash on old decorated surfaces complete all as specified and as directed

M&L for preparation of old surface on ceiling including brooming down, making the surface even and smooth and applying one coat of white wash on old decorated surfaces complete all as specified and as directed

M&L for preparing new steel and iron surfaces of any description over 10 cm Width /Girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as directed

M & L for prepairing old painted steel and Iron surfaces of any description over 10 cm Width / Girth and applying one coat of synthetic enamel paint of any tint complete all as specified and directed.

M & L PCC 1:7:12 type F-2, using 40 mm graded concrete, as in foundation, mass concreting, sunken floor etc complete all as specified and directed

M & L PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate, as in padding, sunken, coping portion rounded chamfered on edge complete all as specified and directed.

M & L 10 mm thick rendering in cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid seperately.

Supply only integral liquid water proofing compound complete all as specified and directed.

S & F for GI tubing 15mm bore, medium grade with all fittings of medium grade fixed to walls, concealed in wall and ceiling or laid in floor incl Taking up or down steel water tubing and connections including cleaning for refixing or removing to store complete all as specified and directed

S & F for GI tubing 20mm bore, medium grade with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor incl Taking up or down steel water tubing and connections including cleaning for refixing or removing to store complete all as specified and directed.

S & F for PPR Pipes SDR 7.4/PN 16 (OD 160mm) with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) fixed to walls, concealed in wall and ceiling or laid in floor incl taking down old pipe complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) Soil, waste and vent pipes , single socketed in any length with rubber ring joints laid in trenches or in floors, fixed to wall complete all as specified and directed.

S & F in repair 75 mm dia PVC (SWR) floor trap, with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed.

S & F in repair PVC (SWR) junction single, (Single T) equal or unequal 110 mm bore complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) bend of any radius complete all as specified and directed.

S & F in repair PVC waste pipe 32 / 40 mm dia and length of pipe 750 mm medium grade with coupling complete all as specified and directed

S & F in repair cast copper alloy, chromium plated Towel Rail 20 mm dia, D-type, 600 mm long fixed with and including Chromimum plated brass screws complete all as specified and directed .

S & F in repair bib tap cast copper alloy with crutch or butter fly handle, screwed down for iron pipe 15 mm bore of tubing fancy type cromium plated complete all as specified and directed.

S&F in repair 15mm Stop valve angle cock fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified

S&F in repair 15mm dia brass chromium plated pillar tap with fly nut with long swan neck screwed for 15mm bore dia of pipe complete all as specified

S&F in repair vitreous china wash basin 550 x 400mm (flat back including cutting for and pinning in ends of brackets or erecting stands but exclusive of fixing of supply and waste pipe

S & F in repair vitreous china squatting pan ‘Orissa pattern’ size 580 x 440 mm white with integral foot rest including connection to trap, and flushing pipe, anti- syphonage pipe, etc and including lime concrete bedding complete all as specified and directed.

S &F in repair vitreous china Wash down water closet (Padestal pattern) white with P or S trap including plastic water closet seat & cover mild steel chromium plated or aluminised hinging device and jet, fushing cistern low or high level, 32mm dia polyethylene fush pipe etc compete all as specified.

S&F Vitreous China Urinal, Half stall type,white complete including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified .

S & F in repairs PVC valveless, syphonic action type flushing cistern, low level , white, with inlet ball valve, float and handle including brackets and flush pipe suitable for IWC of polyethylene of low or high density or PVC 32 mm dia for low level cistern for 10 litres capacity of Complete all as specified and directed.

S & F in repair CP shower rose with or without swivel joints of 125 mm size with shower arm complete all as specified and directed

S & F in repair for PVC Connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed

S & F in repairs PVC water storage tank cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantling of old water tank and removing from site complete all as specified and directed

S & F in repair 15 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and complete all as specified and directed

S & F in repair 20 mm dia Gun Metal, globe or Gate Valve with iron wheel head Screwed both ends for Iron Pipe and complete all as specified and directed

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with cut and mitred beads in squares or triangular n. exc 0.5 Sqm in each pane incl Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames complete all as specified and directed

S&F in repair 18 mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of one side decorative/laminated and other side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in any type of soil for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc and getting out complete all as specified and directed

M&L for returning filling in any type of soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed

M&L for removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L Cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in foundations or mass concrete complete all as specified and as directed by the Engr-in-Charge

M & L for providing reinforced cement concrete M- 25 (Design Mix), using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed.

M & L for providing reinforced cement concrete M- 25 (Design Mix), using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts all as specified and directed.

M & L for providing reinforced cement concrete M- 25 (Design Mix), using 20 mm graded stone aggregate as in lintels all as specified and directed.

M & L for providing reinforced cement concrete M- 25 (Design Mix ) using 20 mm graded stone aggregate as in slab, etc all as specified and directed.

M & L TMT bars 6mm to 8mm dia cut to length, bent to shape required incl. stirrups spacers and incl. mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for use and waste of form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface, square or rectangular of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides and soffits of floor, lintels band & beams including supports, overhangs, etc. with rough finished surface of concrete all as specified and directed.

M&L for Use and waste for form work to soffits of suspended concrete slabs for fair finished concrete surface flat surface complete all as specified and directed..

M&L for Machine cut Kota stone slab flooring 18-20 mm thick, laid over & including screed bed of 20 mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with matching shade pigment including rubbing and polishing complete, all as specified.

M&L for Kota stone slab 18-20 mm thick on vertical surfaces like riser of steps, skirting, dado and pillar laid over & including 10 mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for reinforced in chajjas, water troughs, mangers, shelves, manhole cover slab and similar articles with plain faces set in CM 1:6 type C1 1:3:6 (20mm graded aggregate) including formwork complete all as specified and directed

S&F MS work as in staging/shaft, steel wire fabric, windows, ventilators of angle/rectangular or square hollow section or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors, windows, ventilators etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, window, ventilator fittings and hanging, also fastening and fixing conforming to Fe 410-W (Gde-E-250) quality 'A' complete all as specified and as directed by Engr-in-Charge

M&L for applying two coat of synthetic enamel paint on steel surfaces inc primer of any description over 10cm width or girth not otherwise described and complete all as specified and directed by Engr-in-Charge

S&F Factory made steel ventilator with centre hung shutters, dovetailed or welded including pintol hinges, steel handles, etc. as shown with fixed type including one shop coat of red oxide zinc chrome primer and wire mesh complete all as specified.

S&F 4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg), 75mm thick as in sub base in floor/paving etc including finishing cement concrete surface even and rough to receive top layer complete all as specified

M&L for rubber moulded coloured glossy finish cement concrete chequered tiles of size 30cm X 30cm X 20mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping and the like including weathering, slightly rounded or chamferred angles and throating, use of formwork straight or curved complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches complete all as specified and directed

Surface dressing not exceeding 15cm deep in any type of soil complete all as specified and directed.

Taking down carefully aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pedants, regulators, sockets, light fitting etc and making good the disturbed surfaces of walls/ floor etc matching with the existing surface all as specified and as directed by EIC.

Disconnecting the electrification and taking down DBs (any type of SPN/TPN DBs) and making good to the disturbed surfaces to match the existing surface all as specified and as directed by EIC. Note - Temporary power supply shall be provided by contractor.

Taking down U/S submain wiring aluminium etc and making good the disturbed surfaces of walls/ floor etc matching with the existing surface.

M&L for sub-main wiring (surface) with two single core 4 sq mm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 20 mm dia non-metallic PVC conduit fixed in wall including 4 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC.

M&L Point wiring with 1.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor in and including concealed rigid PVC conduit(ISI marked) medium grade of size not less than 20 mm dia including accessories incl cutting chases , making surface good etc along with contineous earth wire 1.5 Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly including metal flush box with white cover plate & frame for modular switch & socket complete with all accessories complete all as specified & directed for the following:- One light/fan/bell/exhaust fan point controlled by one, 01-way modular type switch 5/6 Amp.

All as per Item No 99 above but on the same board with other switches/sockets

All as per Item No 99 above but for One 5 pin 5/6 Amps socket outlet point on independent board controlled by one, 01-way modular type switch single pole 5/6 Amps.

All as per Item No. 99 above but 2.5 Sq mm multi stranded copper conductor with 2.5 Sq mm copper earth continuity wire connected to earth duly complete for one 15A Socket on Independent board all as specified and as directed by EIC.

S& F in repair wall mounted LED batten Box type fitting Blu colour end caps pre-wired LED fitting all as per cat part No DMLN 1 LT 8-16 with & including LED T8 tubular lamp.

S&F of 10 watt LED light fitting mirror type with high out put diffuser 2 feet, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size other fixing accessories complete all as specified and directed.

S & F angle lamp holder, PVC Polycab type with back plate suitable for batten fittings complete including fixing of 9/10 watt LED bulb all as specified.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed.

S& F double door sheet metal enclosure for DB , 08 way , SPN, with 100 Amps rated bus bar , 240 Volts suitable for housing MCBs and flushed inside the wall and making good for disturbed surface with existing etc complete all as specified & directed.

S & F MCBs SPN 32 amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

S & F MCB SP, 6 to 32 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

Supply and fixing LED street light fitting 20 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including fixed on wall with 02 Nos MS clamp made out of 40 x 6mm F1 and bracket made out of 32 mm dia light grade GI pipe not less than 0.9 mtr long bend to shape including connecting with 1.5 sq mm, 3 core, PVC insulated copper conductor cable 1100 Volt grade complete all as specified & as directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

S&F LED tube light batten 20 watts 4 fts polycarbonate housing, translucent diffuser with LED light source , 2200 lumen, natural white ,surge protection range 2KV, voltage protection range 120-280 VAC , system efficacy not less than 110 Lm/watt for the fitting , power factor>0.95 total harmonic distortation<20% , colour rendering index >80, coefficient colour temp 6500 K, fixed on site with all accessories all as specified and directed.

S & F angle lamp holder, PVC Polycab type with back plate suitable for batten fittings complete including fixing of 9/10 watt LED bulb all as specified.

Supply & Laying XLPE insulated armoured heavy duty electric cable , with multi stranded aluminium conductor served with an inner sheathing of PVC type armoured with galvanized steel wire or tape and PVC sheathed 1100 volt grade,nominal cross sectional area 10 Sqmm 2 core inclu lugs and heat shrinkable PVC Sleeves on exposed surfaces & teflon tape duly insulated complete laid in trenches, ducts, drawn through pipe across the road/path/alongpoles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-charge.

Excavation in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in soft loose soil complete all as specified and directed.

M & L for brick sub class 'B' 250mm x 115mm x 0.75mm and laid in trenches as in protection of UG cable complete all as specified and directed.

Supply and filling in and speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR Part-I and as directed.

M & L for 50mm bore GI pipe (Light grade) laid under road or fixed with pole/wall of culvert as in protection of UG cable incl necessary MS clamp and complete all as specified and directed.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

ABHINAV KUMAR (BID ID -3368979)

G S CONSTRUCTIONS (BID ID -3368310)

SHARI SHAYAM CONSTRUCTION CO. (BID ID -3368516)

N.R.Builders (BID ID -3368543)

A R CONSTRUCTION COMPANY (BID ID -3368666)

Harsh Construction Co. (BID ID -3368780)

SHIVANI ENTERPRISES (BID ID -3368549)