REPAIRS TO JOINERY, FLOORING, PLINTH PROTECTION, VALLEY GUTTER, PLASTERING, CHAJJA, PLUMBING WORK, PCC ETC TO MD AND OTM ACCN AT ASC SUP COY, FD WKSP, CWE S AND GE OFFICE, MES QTRS BARRACKPORE UNDER GE BARRACKPORE

Amount

S&F for steel windows with side hung double shutters (glazed & gauged) including box type hinges with steel handle, frame, steel peg stay, complete without glazing bars (weight not less than 44 Kg/Sqm) , dovetailed or welded to receive wire mesh/glass including one coat of red oxide zinc chrome primer at factory all as specified and directed

S&F for steel ventilators with top hung shutters including box type hinges with steel handle, frame, steel peg stay, complete, dovetailed or welded to receive wire mesh/glass including one coat of red oxide zinc chrome primer at factory complete all as specified and directed

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 all as specified & directed.

Taking down chowkats with shutters (without taking off shutter from the frames) exceeding 1.50 Sqm and not exceeding 4.00 Sqm each all as specified and directed.

Taking down chowkats with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each all as specified and directed.

Taking down shutter of any description exceeding 1.0 Sqm and not exceeding 2.0 Sqm each and refixing in same opening all as specified and directed.

Taking down shutter of any description exceeding 1.0 Sqm and not exceeding 2.0 Sqm each all as specified and directed.

S&F for factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified.

S&F for second class hardwood plain, solid, straight, chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F for 35mm thick, factory made plain, second class hard wood, framed, panelled shutters (three panels) with lock rails and panel of 12 mm veneered particle board with commercial veneering on both faces (BWR type), the size of rail and stile as per IS-1003 (Part-I) (larger size to be provided) klin seasoned and chemically pressure treated fitted to chowkats all as specified and directed.

S&F for 35mm thick second class hard wood glazed/ gauge & skeleton shutters, open rebated & prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, section-8, clause 8.24 (a) all as specified and as directed.

S&F for 30mm thick second class hard wood glazed/ gauge & skeleton shutters, open rebated & prepared to receive glass, gauge etc. (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, section-8, clause 8.24 (b) all as specified and directed.

S&F for mild steel hold fast made out of flat iron (25mm x 3mm) including tarring or coal tar black paint and with drilling necessary holes etc conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) used as in brick, concrete wall for fixing of hold fast on as in coping including necessary form work all as specified and directed.

S&F for 50 mm long stainless steel butt hinges, medium weight all as specified and directed.

S&F for 125 mm long mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed all as specified and directed.

S&F for 100 mm long stainless steel butt hinges, medium weight all as specified and directed.

S&F for 200 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 150 mm long aluminium anodised extruded alloy handle fabricated type all as specified and directed.

S&F for 250 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed all as specified and directed.

S&F for second class hardwood small fittings such as brackets of any type, latch and hinge blocks, shapes door and window stops and the like including all necessary articles not exceeding 200 Cucm each all as specified and as directed.

S&F for 100mm long aluminium anodised hasp & staple safety type including hinge pin, bolt to hinge plate etc complete all as specified and directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm & fixed with stainless steel wire staples in window and door as in new door/window complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36 mm normal dia of wire & average width of aperture 1.40mm & fixed with stainless steel with staple/ wooden beads in steel window/wooden door complete as in repair all as specified and as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden or steel frame, glazed with putty or fixed with beads etc all as specified and as directed.

S&F for 3.0mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane all as specified and as directed.

S&F for 3mm thick figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 sqm each pane all as specified and directed.

M&L for applying one coat of white wash of old surfaces of walls, cornices etc after preparation of old plastered surfaces complete all as specified and directed.

M&L for applying one coat of white wash of old surfaces of ceiling after preparation of old plastered surfaces complete all as specified and directed.

M&L for applying one coat of oil emulsion distemper over old decorated plastered surfaces of wall after preparation of old surfaces complete all as specified and directed.

M&L for applying one coat of cement based paint on old decorated surfaces of walls including preparation of old surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm in width or girth all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted steel surfaces of any description, exceeding 10cm in width or girth, not otherwise described all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified & directed.

M&L for apply two coats of synthetic enamel paint over a coat of pink primer after preparation of new wood surfaces of any description over 10 cm width or girth complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises all as specified and directed.

S&F for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8mm thick exceeding 0.18 Sqm but not exceeding 0.38 Sqm each (square /rectangular) as in floor, set over 15 mm screed bed in cement mortar (1:6) and jointed in neat cement slurry and pointed in colour cement with pigment to match the colour of tiles complete all as specified and directed.

S&F for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8mm thick exceeding 0.11 Sqm but not exceeding 0.18 Sqm each (square /rectangular) as in floor, set over 15 mm screed bed in cement mortar (1:6) and jointed in neat cement slurry and pointed in colour cement with pigment to match the colour of tiles complete all as specified and directed.

S&F for glazed ceramic coloured (colour & shade as approved by GE) wall tiles (vertical) 450mmX350mmX7mm set and jointed with neat cement slurry and pointed in colour cement to match over and including 10 mm thick screed bed of cement mortar (1:4) complete all as specified and directed.

M&L for 20 mm thick granite (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the of granite stone including grinding, polishing and rounding edges over and including 15 mm thick screed bed of cement mortar (1:6) including dismantling old granite, bedding complete all as specified and directed.

M&L for pre-polished coloured chequered cement concrete tiles 30cm x 30cm x 25mm thick (glossy type), set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 15 mm thick cement screed bed in cement mortar (1:6) including dismantling of old chequred cement concrete tiles complete all as specified and directed.

M&L for machine cut cudappah stone slab flooring 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and rounding edges over and including 15 mm thick cement screed bed in cement mortar (1:6) complete including dismantling old slab all as specified and directed.

M&L for 50 mm thick PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor finished, even & smooth with using extra cement complete all as specified and directed.

S&F for 25mm dia (heavy duty) mild steel, chromium plated, single curtain rod (wall thickness not less than 1mm) complete as in repair all as specified and as directed.

S&F for mild steel brackets powder coated suitable for curtain rod all as specified and directed.

S&F for 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete as in repair all as specified and directed.

S&F for 125/110mm dia PVC (SWR) gully trap , settings and jointing with solvent cement complete as in repair all as specified and directed.

Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) over fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement on plastered surface all as specified and directed.

All as per Item No.52.00 here-in-before but plastering in patches, not exceeding 3 Sqm each patch all as specified and directed.

M&L for rendering 15 mm thick in cement plaster, 1st coat 10mm thick in cement mortar (1:6) & 2nd coat 5mm thick in cement mortar (1:4) with water proofing compound @ 2% by weight of cement surface finished even and smooth without using extra cement all as specified and directed. (Note : WPC shall be measured and paid separately, WPC shall be used in second coat only)

M&L for rendering 10mm thick in cement mortar (1:4) on ceiling, chajja etc surface finished even and smooth without using extra cement on plastered surface all as specified and directed.

M&L for applying three coats of white wash on surface of wall including preparation of new plastered surface complete all as specified and directed.

M&L for applying three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of alkali resistant primer on wall as directed by GE after preparation of newly plastered surfaces of walls complete all as specified and as directed.

M&L for two coats of cement based paint over a coat of cement primer on newly plastered surface of walls including preparation of undecorated surface complete all as specified and as directed.

Demolition of brick work built in cement mortar etc complete all as specified and directed.

M&L for brick work with subclass 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings all as specified and directed.

M&L for 6mm thick fibre asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with 'L' or 'J' type hooks all as specified and directed.

M&L for 6mm thick fibre asbestos cement two pieces adjustable serrated ridge for corrugated or semi corrugated sheets fixed with 'L' or 'J' type hooks all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering etc all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Dismantling of wrought iron or mild steel work of any description etc all as directed.

Taking down existing steel sliding door shutter exceeding 4 Sqm but not exceeding 6 Sqm at any position and any description including necessary scaffolding as required on site and refixing at same position/location including where required cutting, drilling, fittings, riveting or welding connecting with fish plate, gusset plates etc for smooth sliding of steel gates/shutters complete all as specified and directed.

S&F for joist, channel, flat iron, angle or tee sections, fixed independently, without connecting plates etc (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 410-W (Gde E-250) quality A all as specified and directed.

S&F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including where required drilling, fittings, riveting or welding connecting with fish plate, gusset plates etc of Fe-410-W (Gde E-250) quality 'A' complete all as specified and directed.

S&F for ball bearing or rolling wheel minimum dia 65 mm to 75mm for steel sliding doors shutter including necessary fittings/spindle and welding complete as in repair all as specified and directed.

M&L for providing PCC (1:5:10) type E2 (using 40mm graded stone aggregate) as in filling sunken floor of bathroom/toilets etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:3) to sunken portion of slab with using water proofing compound finished even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately)

M&L for preparation of plastered surfaces and applying polymer modified bituminous elastomeric water proof coating as per manufacturer's instructions for sunken portion of toilet, bathroom and similar portions at any place/location and in any condition all as specified and directed by Engineer-in-Charge (Make: PIDILITE INDUSTRIES LTD (Dr FIXIT proof coat) or equivalent of IWL/TEXSA /TIKI TAR as approved). The work should be carried out by Authorised Applicator of Manufacturer. (NOTE: The rate includes for preparation of surfaces treatment and sealing of all joints, cracks, corner and junction of pipes etc. and ponding test complete all as directed by Engr-in-Charge)

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet all as specified and directed.

S&F for false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee gird false ceiling using “T” Gird System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 4mm thick non asbestos fibre cement board (oceanic) of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T gird Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Gird module to form all complete as per the drawing & directions of Engineer-in-Charge.

S&F for 32mm dia waste fittings, brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks & fly nuts, flanged end bedded in red lead cement & other end fixed complete as in repair all as specified and as directed.

S&F for 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB, urinal etc. as in repair all as specified and directed.

Supply only integral water proofing compound, ISI marked complete all as specified.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, floor, trenches etc after dismantling of old PVC pipe in any condition complete as in repair all as specified and directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, floor, trenches etc after dismantling of old PVC pipe in any conditon complete as in repair all as specified and directed.

S&F for 110mm bore PVC (SWR) bends any radius provided with access door complete as in repair all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 15mm bore pipes all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 20mm bore pipes all as specified and as directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 15mm bore pipes with new fittings etc all as specified and as directed. (Note : Pipe shall be obtained from Item No 85.00 above)

S&F for 15mm dia tubes (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) all as specified and directed.

M&L for cutting chase pinning in brick mass and making good facing where required and pointing in cement and making good in cement mortar (1:3) cutting not exceeding 10cm in girth complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 20 mm bore pipes with new fittings etc all as specified and as directed. (Note : Pipe shall be obtained from Item No 86.00 above)

S&F for 20mm dia tubes, (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors etc all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F for 25mm dia tubes, (medium grade) galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors etc all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 20 mm bore pipes with new fittings etc all as specified and as directed. (Note : Pipe shall be obtained from Item No 92.00 above)

S&F for 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with letter 'HOT' or 'COLD' with long screwed shanks &fly nuts, screwed for iron pipes complete as in repair all as specified and as directed.

S&F for 15 mm bore angular stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete as in repair all as specified and directed.

S&F for 15 mm stop valve, cast copper alloy, fancy type, CP screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe fixed complete as in repair all as specified and directed.

S&F for 20mm dia gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed complete as in repair all as specified and directed.

S&F for 15mm dia bib taps, cast copper alloy with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferule, chromium plated, fancy type with long screw type fixed as in repair all as specified and as directed.

S&F for 15mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15mm-90gms) complete as in repairs all as specified and as directed.

S&F for vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern & flush pipe) as in repairs including connection to trap & to flushing pipe, plastic seat cover, anti-syphonage pipe etc. complete including making good to floor complete as in repair all as specified and directed.

S&F for plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete as in repair all as specified and directed.

S&F for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests with P or S trap (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demolition of PCC / lime concrete bedding existing pan complete as in repairs all as specified.

S&F for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repair all as specified and directed.

S&F for vitreous china wash basin, white, flat back, size 580 X 450mm, excluding taps, chain and plug and porcelain stopper but including waste pipe, brackets and cutting for and pinning in ends of brackets or erecting stand complete as in repair all as specified and directed.

S&F for PVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete as in repair all as specified and as directed.

S&F for brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges as in repairs all as specified and as directed.

Disconnecting existing tanks of (exceeding 500 & not exceeding 1000 litres in capacity), setting aside (or lowering if required) and cleaning, removing all scale and dirt etc from tanks and mouth of pipe including hoisting (if required) reconnecting and refixing in positing all as specified and as directed. (NOTE: Date of cleaning must be written at side of water tank with white paints after cleaning of tank)

S&F for 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layers, white, hoisted and fixed in position with cover and locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I all as specified and directed

S&F for 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete as in repair all as specified and directed.

S&F for 125mm size brass chromium plated shower roses with arms, swivel joints, including fixing to steel pipe or union complete as in repair all as specified and as directed.

S&F for grating doom 125 mm dia PTMT (minimum weight 40 gms) complete as in repair all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for cutting holes into or through brick walls built in cement mortar and making good in cement mortar (1:3) or concrete (1:2:4) type B1 as required for superficial area exceeding 100 sqcm & not exceeding 150 sqcm complete all as specified and directed.

M&L for preparing surfaces of wood or wood based materials, steel and iron work, new or old treating end of the posts, backs of chowkats etc area tarred exceeding 0.1 sqm but not exceeding 0.5 Sqm each and treated with tar or coal tar black paint complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection/paving including finishing the cement concrete surface even and smooth without using extra cement in slope including making joints of every 2.5m and at corner filled with bitumen 85/25 and sand in ratio (1:2) by weight and complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channel and drains etc complete all as specified and directed.

M&L for forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete alla as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in subbase of floor complete all as specified and directed.

M&L for 25mm thick cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor/paving etc complete all as specified and directed.

M&L for PVC (SWR) 'P’ trap of 115/110mm bore compelte as in repair all as specified and directed.

M&L for PVC (SWR) 'S’ trap of 115/110mm bore compelte as in repair all as specified and directed.

M&L for cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required dia of pipe 150 mm complete all as specified and directed

S&F for 75mm dia PVC (SWR) multi-floor trap plain with grating including jointing with solvent cement complete as in repair all as specified and directed.

S&F for 75 mm bore PVC (SWR) bends any radius provided with access door complete as in repair all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete as in repair all as specified and directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete as in repair all as specified and directed.

S&F for 75mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal provided with access door complete as in repair all as specified and directed.

S&F for 110 mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal provided with access door complete as in repair all as specified and directed.

S&F for 75mm bore PVC(SWR) junction single, (single T) equal or unequal providing access door complete as in repair all as specified and directed.

S&F for 110mm bore PVC(SWR) junction single, (single T) equal or unequal providing access door complete as in repair all as specified and directed.

S&F for towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete as in repair all as specified and directed.

Demolition of cement concrete (reinforcement) in ground floor not exceeding 15 cm thickness (below or above ground level) , reinforcement cut as required to facilate demolition all as specified and directed.

M&L for formwork to the soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping ) and making flat, rough finished surfaces of concrete complete all as specified and directed

M&L for RCC (nominal mix) (1:2:4) type B1 (using 20mm crushed stone graded aggregate) used as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 8mm dia in stirrups, spacers and binders complete all as specified and directed

S&F for 125mm long CP health faucet (ABS) with rubbit cleaning system, one meter long PVC flexible tube for 15mm dia and ABS wall hook complete as in repair all as specified and directed.

Dismantling timber scantlings (un-framed work) 40 sq.cm and over in section, in any position complete all as specified and directed.

M&L for second class hard wood in scantling, clean swan as in un-frame work, fixed with nails complete all as specified and directed.

M&L for cutting out cracks to V-Section existing roofs or terracing cleaning out, wetting, grouting with cement & sand slurry (1:3) complete all as specified and directed.

Removing plant including roots by dismantling of brick work/PCC/RCC including necessary scaffolding any type in any location/position i.e. roof, parapet wall near pipes etc and applying concentrated hydrochloric or sulphuric acid after removing roots for preventing the regrowth and making good of disturbed portion using PCC (1:2:4) type B0 & 10mm thick plaster in cement mortar (1:3) size of disturbed portion 150mm X150mmX200mm complete all as specified and directed.

M&L for writing letters or figures (block, roman, italic or Indian) not exceeding 30cm high after cleaning the existing surfaces complete all as specified and directed.

M&L for writing stops, commas, short lines dashes, hyphens, bracket etc after cleaning the existing surface complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410 (Gde E-250) quality 'A' all as specified and directed.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm not exceeding 10cm long with shank 5 to 10mm dia complete all as specified and directed.

Taking down of existing un-serviceable tarfelt / bituminous membrane on roof and parapet of any roof height carefully by cutting chiseling, cleaning the surface by scraping, brooming, brushing etc and removing the rubbish from site complete all as specified and directed.

M&L for applying evenly a coat of bitumen primer on roof, canopy, chajja, parapet (vertical surface etc) @ 0.40 Litre / Per Sqm by the same membrane manufacturer of density 250C, 0.87 to 0.89 litre and viscosity 70-160 cps after proper cleaning the roof surfaces (horizontal/vertical) and providing APP based polymeric membrane minimum weighing 3.6 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (weight not less than 150 gms / sqm) laid on primed surface with side over lap of 80 mm and end overlap of 100 mm, using bitumen torch or by LP gas torching and sealing all joints etc and ensuring complete thermo fusing and applying one coat of aluminum paint over it complete all as per manufacturer instructions complete all as specified and directed.

M&L for 20 mm thick screed bed in roof surfaces with cement mortar (1:4) with WPC @ 2% by weight of cement finished complete all as specified and directed. (Note : WPC shall be measured and paid separately)

Taking down eaves gutters and rainwater pipe (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L for 0.63 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashing (legth & girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

PUNAM ENTERPRISE

S..S. ELECTRIC CO.

M/S. ARUP KUMAR DEY

DEYS ENTERPRISE

B N ENTERPRISE

DE CONSTRUCTION CO

M/S KARTICK CHANDRA CHAKRABORTY