permanent shelter for SSD pilgrims, Tirumala

PART-A( Percentage tender items)

Demolishing and disposal of unserviceable materials with in 100 metres lead Unreinforced cement concrete up to 15cm thickness

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead-R.C.C.work

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-Mechanical means up to 3m depth

Earthwork excavation in hard rock (blasting prohibited) with rock breakers including breaking rock, loading in tippers and disposal with intial lift of 3 m and lead up to 1000 mt, including trimming bottom and side slopes in accordance with requirements of lines grades and cross sections as per technical specifications clause 302.3.5 MORD/301 MORTH - Mechanical means.

Note: 1 1. The quality, quantity and availability of rock shall be checked before affording credit. 2. In case some rock is issued to the contractor, rate as arrived per cum to that issued extent shall be deducted. 3. In case some rock is issued to the contractor at site , the item carriage shall be restricted / reduced to that extent. 4.Being small quantity, manual loading will be economical in this case and has been provided accordingly.

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work. Note: Cost of transportation of good quality earth has not been included. Only labour for carrying carted earth with a lead of 50m to the foundation pits has been taken in the rate. The cost of carted earth / sand may be worked out separately if the same is not available from adjoining area.

Conveyance of excavated surplus earth/debris to a distance 2 kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete (1:4:8) using 40 mm ( 0.54 Cum), 20 mm (0.27Cum) and 12 mm (0.09Cum)nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, machine mixing cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5)-Grade M15 using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kg),. 10 mm HBG crushed metal, 0.362 cu.m (471 kg) , sand 0.407 cu.m (616 kg.) and cement 380 kg with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC) etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department , including cost of centering, shuttering charges but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402).

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kg/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

-do- For footings

-do- Columns up to Basement

-do for Plinth Beams

-do- Columns in First Floor

-do - Lintels in First Floor

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars of specified grade (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). -do- below 36 mm Fe 500/Fe-500D/Fe550 Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Construction of Brick Masonry in CM(1:6) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick masony in C.M (1:5) for super-structure using second class traditional size bricks (23X11X7CM) including cost of all materials, seigniorage charges, labour and all operations for constructing half brick masonry, mixing cement motar, curing etc., complete - for finished item of work, First floor

Plastering in Cement mortar (1:5) 20 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

Plastering in Cement mortar (1:5) 12 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

Flooring with Cherry Red granite 18-20mm thick up to 2.43 m set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the slabs against supply)

Flooring with telephone Black Granite 18-20 mm thick upto 2.43 M set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the slabs against supply)

Flooring with Antiskid floor tiles 1st quality of all series & shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including white cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

- do - Supply of Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Finishing the sides of walls with Ist quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg /10 sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Supply of glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Finishing the side of walls with high polished Galaxy granite 18-20 mm thick up to 8'-00 (2.43m) (premium quality) set over base coat including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M (1:3) 12mm thick & cement slurry of 33 kgs/ 10 Sqm shall be used for fixing wall granite inlcuding cost and conveyance of all materials, curing, incidental charges etc., complete ( No separate plastering shall be paid to the walls ). in all floors.(Note: Unless otherwise finishing side walls completed, no pre-payment shall be made for the granite against supply).

Supply of telephone Black Granite 18-20 mm thick upto 2.43 M

Half Rounding the edges of Marble/ Granite stone slabs of all thicknesses including polishing the same

Full Rounding the edges of Marble/ Granite stone slabs of all thicknesses including polishing the same

Supplying , fixing and fabrication in position M.S tubes & pipes of all diameters as per ISI 1161 of approved size design including Labour charges for fabricating all heavy steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges, etc., including labour charges for fixing iron doors, iron windows and window grills in positionn including painting the same with Two coats with Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply, Fabrication and fixing of Mild steel base Plates of diffrent sizes including cost and conveyance etc complete as directed during the execution of the work including Labour charges for fabricating all heavy steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges, etc including cost of fixing in position including painting the grills with two coats of with synthetic enamel paint over a red oxide metal primer paint (total three coats) grade -1 of approved make and colour etc., complete as directed during the execution of the work.

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness (Total Coated Thickness-TCT), Coating: Alu-Zinc coating AZ150 GSM. Tensile strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Supply of roof accessories medium size ridge, barge cap corner trim, L-Flashing, down pipes, gutter etc., with 0.47mm thick, width:0.585, Length maximum 2.50 mts.

Painting two coats with Acrylic Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade over cement primer exterior grade-2, (total three coats) after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911for new external walls.

Painting two coats with Acrylic Emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand over primary coat (total three coats) using ready mixed cement primer (water thinnable) for interior grade-1 (total three coats) and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls New work

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply and fixing of stainless steel SS-304 grade tubes, sections, plates , sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing , polishing , lacquer finishing , to present seamless finishing etc., complete as directed during execution

Providing and applying wall putty of white cement or polymer or cement based putty of approved make with average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2-3 hrs. sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work, excluding scaffolding charges - for internal and external walls.-do- for new work

Supply of glow sign vinyl stickered name plate / sign (or) instruction boards using 4mm ACP (Aluminum composite panel )sheet as back ground and glow sign vinyl sticker one layer for letters of different sizes as directed during execution including cost of ACP sheet, vinyl sticker and all labour charges for computer design and cutting, pasting and fixing the boards as directed during execution .

Supply and fixing of 10 mm wide PVC edge beading including cost and conveyance of all materials and incidental charges, etc., complete.

Flooring with cement concrete floor tiles of 25mm thick of following sizes set over base coat of cement mortar (1:6) 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & jointed with neat cement to full depth mixed with pigment of matching shade including cost & conveyance of all materials, etc., complete for finished item of work.

Plain cement concrete general purpose tiles conforming to IS:1237 using aggregates, cement, pigments of size 300 X 300 x 25 mm of any shades.

Flooring with cement concrete floor tiles of 25 mm thick confirming to IS 1380-12013/IS 1237-2012 of following sizes set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & jointed with neat cement to full depth mixed with pigment of matching shade including cost & conveyance of all materials, etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Chequered cement concrete heavy duty tiles confirming to IS:13801 using aggregates, cement, pigments of size 400 X 400 x 25mm of any shades.

Supplying & Fixing Orissa Pan white glazed W.C 1st quality ISI marked conforming to IS:2556-Part-3-1981 with "P" or "S" trap 580x440 mm ISI Mark or equivalent brand approved by the department.

Supplying and Fixing European Water Closet of 1st quality confirming to IS:2556-Part-2-1973 of white glazed with 'P' trap with ISI mark or equivalent brand approved by the department.

Supply & fixing of PVC low level cistern with internal components & short bend: 10 Litres capacity Single Flush

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supplying & Fixing white glazed flat back half stall urinals 590 x 375 x 390 mm 1st quality confirming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm confirming to IS:2556 - Part 6, Sec-6-1974 fixed with screws complete Indian make with ISI mark or equivalent approved by the department.

Supplying & fixing oval shape basin white (520x410mm)parry or equivalent

Supply & Fixing of Bibcock cum Health Faucet with 1m long tube and wall hook of Jaquar Continental series, Chrome Finish with 7 years warranty.

Supply & Fixing of Angular stopcock with wall flange Jaquar Continental series, Chrome finish with 7 years warranty

supply and fixing 12.7mm heavy duty dia high neck pillar cock 1st quality Indian make 400 grams

Supply & fixing of Waste coupling Jaquar make, Chrome finish with 7 years warranty

SYMET BIB COCK (CAT.NO:125) (20mm) 3/4'' size with flange deluxe handles, 98mm long and 114mm high and 48mm breadth 18mm seat dia and replaceble washers, having approx. weight of 125gms.

Supply & fixing of N.P coat hook

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007).

54.00 mm OD pipe SDR - 13.50

28.60 mm OD pipe SDR - 13.50

22.20 mm OD pipe SDR - 13.50

Supplying and fixing Gunmetal Gate (GM peet) valve as per IS - 778 Class-I, Indian make heavy type 50 mm NB size.

Supplying and fixing Gunmetal Gate (GM peet) valve as per IS - 778 Class-I, Indian make heavy type 25 mm NB size.

Supply of round jalli

4" (101.6mm) Nahany Trap [without jali with inlet ]

Supplying, laying and jointing in position the following dia metre of PVC/ SWR pipes & fittings ( as per ISI standards) 6Kg/sqcm (Type -B) including labour charges for laying, fixing and commissioning the PVC pipes including couplers/ bends/ tees etc.,any dia including fixing necessary fiittings like bends, plugs, couplers, junctions, tees, etc., with solvent jointing as per standard practice.

160mm dia pipe double Socket

110mm dia pipe Single socket

75mm dia pip Single socket

Supplying and fixing in position 600 x 450 mm size wall mirror with 5 mm thick glass (Saint Gobion) with 6 mm plywood IS 303 bwr (both sides commercial) back in position with 12 mm Aluminium 'U' channel (Jindal make) including cost and conveyance of all materials etc., complete

Manufacture as per BIS:12592 (Part 1&2) Supply & Delivery of Pre-cast concrete manhole covers and frames with ISI marking anywhere in A.P.,F.O.R. destination including, loading, unloading & stacking at site but excluding all taxes.Heavy Duty.-10 with 560mmdia clear opening

Supply of the following Anodized Aluminum Fixtures for Doors and windows

Anodized Aluminum Tower Bolts 10mm dia X 150 mm Long with ISI Mark IS:204

Anodized Alluminium Aldrops sliding door bolts 16 mm x 200 mm (3T-Pieces)

Anodized Aluminium Door Handles (IS:208) 150 mm long

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.

Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at allcorners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But no extra payment on this account shall be made.

Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

electrical items

Supply and Fixing of ISI Mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe with all accessories fixing on chromium plated metallic base saddles for surface wiring on Brick / stone walls, RCC roofings, Trusses, channels including all labour charges etc., complete. (If PVC Pipes are fixed on Trusses / Channels with MS Clamps, the rate for MS Clamps will be paid Separately) Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal

Supply and Fixing of ISI mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in new / existing brick building, walls, columns, beams duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and masonry work for light, fan and separate plug point including all labour charges etc., complete. Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal

Supply and wiring with 3 run of 14/0.3mm (1.0 sq.mm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping with 3 plate Jumbo ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Wire Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: Legrand Arteor / Schneider Zen cello / Gold Medal / GIFA / L&T englaze / Crabtree - Murano / Amare / Ducor / GM Four-Five

Supply and run of 3 wire of 14/0.3mm (1.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and run of 3 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and run of 3 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and fixing of fabricated M.S clamps made out of various sizes of (25mm x 3mm, 25mm x 6mm etc.) MS flat with necessary holes on either side with suitable MS bolts and nuts and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of PVC pipes, Conduit pipes etc., on Trusses / Channels etc. including all labour charges etc., complete.

Supply and fixing of 6 /10 Amps 1 way 1 module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree -Murano - Amare - Ducor/GM Four-Five

Supply and fixing of 6 /10 Amps 3 / 2 pin 2 module Modular Socket with shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare -Ducor/GM Four-Five

Supply and fixing of 16 /20 Amps 1 Way 1 Module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree -Murano - Amare - Ducor/GM Four-Five

Supply and fixing of 20 Amps 2 Module Modular Socket with Shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare -Ducor/GM Four-Five

Supply and fixing of 6A, 3-Plate Jumbo Ceiling Rose on the existing junction boxes, T.W Board etc., and giving necessary connections. Makes: Anchor / Gold medal (Olive) / GM (G Home) / Havells ( Reo)

Supply and fixing of 100 W Fan Step Regulator of 2 Module on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA)/ L&T englaze /Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and erecting of fan hook ( 'S' hook) of 12/15mm dia M.S. rod / bar grouted in MS channel / RCC slab with making the slab as original (repacking) with cement mortar etc

Supply and Fixing 19/20mm dia MS tubular fan down rod of one meter length with bolts & nuts duly painted with matching colour of fan complete

Supply and Fixing 19/20mm dia MS tubular fan down rod of Two meters length with bolts & nuts duly painted with matching colour of fan complete

Fixing of Ceiling fan including transportation and giving connections with twin core wire etc., complete.

Fixing of given (9" to 24") Exhaust fan on to the existing hole and giving necessary connections complete.

Fixing of CFL luminaire (Down lights / Mirror optic / Ornamental type fitting)/ Well glass fixtures with all necessary accessories in false ceiling / on wall including giving connections and all labour charges etc., complete.

Fixing of given T5 / T8 batten light luminaire on wall / Ceiling / Trusses / Channels, on PVC/ TW round blocks / Epoxy insulator / 3"x2"x1" TW reaper with all accessories, labour charges and giving necessary connections.

Supply and fixing of 12 Modular Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor/GM Four-Five

Supply and fixing of 12 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells/ ABB /Indo Asian /Siemen / Fortune Art.

Supply of 2 Module Plastic surface box

Supply and fixing of 12way SP & N Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly on the surface of the wall etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of 6 to 32 Amps DP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 6 to 32 Amps range S.P MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of RCCB Up to 40A Double Pole, 30mA for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of RCCB Up to 40A Double Pole, 100mA for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing universal mounting metal plug board and socket suitable for D.P. RCCBs including labour charges for concealed mounting. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and transportation of 35 Sq.mm 3 1/2 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Supply and transportation of 16 Sq.mm 4 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Laying of U.G cables upto 50 Sq.mm and back filling of trench including labour charges etc., complete.

Laying of U.G cables up to 50 Sq.mm through existing G.I.Pipe/HDPE pipe and back filling of trench including labour charges etc., complete.(Excluding the cost of G.I Pipe/ HDPE pipe)

Supply Laying and Transportation of Outer dia 78mm and inner dia 63mm, 6Kg/Sq.Cm (PE- 100 grade) double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II. Make: DURA LINE (Dura Guard) or its equivalent make.

Supply and fixing of fabricated M.S clamps made out of 25mm x 3mm MS flat with necessary holes on either side with suitable 1 1/2" coach screws and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of UG Cables of size 25 Sq.mm to 50 Sq.mm on walls etc., including all labour charges etc, complete.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) for 35 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) upto 16 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making one end termination with heavy duty single compression brass gland as per BS 6121:2005, IP 66 complete, SIBG type, heavy duty Alluminium lugs duly crimped with crimping tool, PVC tape etc for 35 Sq.mm with brass washers of Armoured PVC insulated & PVC sheathed / XLPE aluminium conductor cable of 1100 volt grade as required of size. Make: Dowels / Comet / SMI

Earth Work excavation for trench for laying of U.G. Cable in ordinary Soils, manual means to the required width and depth and depositing the same on bank as directed during execution etc., complete

Cutting open cement concrete road

Cement concrete using 20mm HBG metal in CC (1:3:6) laid in Layers of not more than 15cms thick well compacted including curing cost and conveyance of materials etc., complete

Plastering in CM (1:6) with 12mm thick using river sand including curing, conveyance of materials etc.

Supply of 225 X 295 X 122 Sizes thermo-plastic cable junction boxes with IP66/67 weather proof, for outdoor installation with knockouts for cable entry including terminals etc., complete (sizes in mm). Make : Hensel/Sadhrish

Providing earthing as per IS 3043/ 1987 with 100mm (ID), 13mm thick C.I. Pipe of 3.0 mtr. length after excavating an earth pit of size1.5 m X 0.9 M X 3.00M(Top 1.50 m X 1.20 m X 0.9m & bottom 1.20 M X 1.20 M X 1.65 M) and filling with a homogenous layer of 40 Kgs. of Coke / Char Coal, 20 Kgs. of Salt and the required quantity of sand around 100mm pipe from the bottom of the pipe to a height of 2.7mtr. and filling the remaining excavated portion with earth and consolidation / Settlement of the trench should be done by filling with sufficient quantity of water

A concrete bed of size 0.8 M X 0.8 M X 0.1 M thick and an inspection chamber having inside measurements of 0.4 M X0.4 M X 0.4 M with wall thickness of 100 mm with cement concrete CC (1:2.5:5) using 20 mm HBG Metal is to be constructed with side wall 100 mm above ground level and plastering the exposed walls neatly with CM (1:3) with 12 mm thick. The Top of the Inspection Chamber is to be provided with reinforced precasted RCC Slab with 40mm thick with lifting hook. The top of C.I. Pipe is to be fixed & welded with suitable G.I. Wire mesh funnel 50mm x 6mm G.I. Strip having length of 300mm is to be fixed to the top of C.I. Pipe with G.I. Clamps

fabricated with 50 x 3mm G.I. Flats with necessary bolts and nuts and necessary welding to be done to the clamps and C.I. Pipe. 2 Nos. of holes are to be drilled on either side of G.I. Flat for Extending earth connections. 65mm dia PVC Pipe is to be embedded at the pit entry for earth. After laying earth from earth conductor bus to Electrode trough PVC Pipe, the surface should be covered with bitumen and grease. The cost of GI/Copper flat to be run from CI Pipe electrode to the equipment is to be made separately on running meter basis. The work shall be executed strictly as per IS 3043 - 1987. The rate includes cost and conveyance of all materials, labour charges, incidental charges etc., complete

(Note:- Necessary meggaring testing is to be carried out in the presence of concerned Engineers and measurement of resistance shall be as per ISI standards)

Supply and run of ' 8 ' SWG G.I wire for earth electrode to required places by concealing in walls, flooring by cutting the grooves and replastering neatly and giving necessary connection with 3/8"x2" GI Bolts, Nuts and Washers Wherever joints has to be done. The strip has to be either riveted (or) bolted (or) gas welding neatly and all labour charges etc., complete.

Supply of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24V DC, power input not more than 30W, air delivery not less than 220 cubic meter/min and a minimum service value of 7.0, without Remote and without regulator. Makes: Atomberg/ Halonix/Havells/ Crompton

Supply of 56" (1400mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24V DC, power input not more than 32W, air delivery not less than 240 cubic meter/min and a minimum service value of 7.0, with remote and without Regulator. Makes: Atomberg(GV2 )/ Halonix(Plasma)/ Havells (Efficiencia Neo)

Supply of 36"(900mm) 5 star rated BLDC sweep ceiling fan with double ball bearings input voltage 230V AC convered to 24V DC, power input not more than 28W, air delivery 157 cubic meter/ min with remote / without regulator. Makes: Havells / Atomberg and TTD approved brands only)

Supply of 12" (300mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with mark Makes: Crompton / Almounard / Havells Ventil Air-DB

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=100 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty. a) LUMINAIRE MAKE : Phillips / GE- Venture / Crompton / Wipro / Bajaj / Havells / Halonix /Jaquar /HPL/GM / GreenLites / Gold Medal/ Eveready/ B57Rhino/ Panasonic/ Ecolink/Capart. b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG/ Everlight

Supply, Installation, Testing and Commissioning of high-quality integrated LED high bay luminaire with a minimum system lumen of 10K Lm and system wattage not exceeding 64W with an efficiency of minimum 160 lumen/watt. The luminaire should have 90 degree beam angle, CCT of 4000K with SDCM of <5 with IP65 protection and IK08. The housing should be of high-quality pressure die cast aluminium with Surge Protection of 6KV. It should have an operating temptation of -10D to 50D input voltage of 120-270V, Life time of 50K hours @L70, THD <10% and power factor of 0.95

It should have universal mounting arrangements ie., Suspensiono (eye bolt) with a lockable pin. And conformity to IEC62384, IEC 61347-2-13, IEC 61547, IEC 61000-3-2 @ CISPR 15/EN 55015 (9 KHz to 30MHz). All cables used in the product should be IS compliant.BIS approval for Both Driver and the luminaire needs to be submitted for records. Make & Model: Philips BY615P LED100S 4000 WP PSU CR / Equivalent model in ENDO / ERCO.

Supply of 39-40W LED Well glass fitting with the following specifications. Makes: Philips / Crompton/ Havells and TTD approved brands.

Optical Parameters: Wattage : 39-40W Lumen output : 4400 ±5%lm System Efficacy : 110 lm/W CRI :>=70 Colour Temperature(K) : 5500 - 6500

Electrical Parameters Surge protection upto 4 KV Power factor : >0.95 Operating voltage: 160-325V AC Operating Frequency: 50 ± 3Hz

Mechanical Parameters IP grade : IP66 Housing pressurte diecast aluminium THD: <10% Life: 50000 Hrs Warranty : 5 Years Wiring the fitting should be supplied with in built 3C x 1.5 Sq mm wire of length 0.5 mtr

Plywood BWR/ BWP Grades - IS:303 (BOILING WATER RESISTANTI)

9 Ply - 19 mm thick Plywood

Supply and transportation of 60W LED Street light Luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass/ temperature protective polycarbonate diffuser, supply input voltage 120 - 270V AC, P.F > 0.90, high power LEDs having System Efficacy >=120 lumens/watt and junction temperature < 70°C, with Ingress protection IP66, Luminaire performance complies to IS 10322 (Part 5/Sec-3), driver surge protection 4KV, in-house additional Surge protection 10 KV with optics distribution, THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty.

a) LUMINAIRE MAKE : Wipro(Skyline) / Philips (Green line) / GE-Venture / Crompton(Neo Series) / Bajaj (Edge) / Halonix (Lumos - Super) / Havells (Endura Series)/ Valmont (Supernova) /Capart (Premium) / Greenlites (Hi-Lux) /Polycab /Keselec/ HPL (City Vision)/ Jaquar (Premium) /Eveready/ Surya (Lexon) /FortuneArrt (Leaf) / Rhino (GPSL04)/ Orient(Fiest Plus) /Bee-lite (Gritty)/ Ecolink(Durastreet Gen II) b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG

Supply & fixing of 1 1/4" dia 'B' class GI pipe not exceeding 1.5Mtr long with necessary bending (120° to 135°) to the wall or to the pole as directed during execution duly grouting 2 Nos. of MS angles of 35x35x5mm having length 20Cm (grouted portion of MS angle into the wall 7.5cm) and fixing with 2 Nos. of MS clamps fabricated with 25mmx3mm MS flat with suitable holes and 4 Nos. of 3/8"x2" MS bolts, nuts & washers for fixing on the wall / 2 Nos. of suitable MS clamps with bolts, nuts for fixing to the pole etc., complete. A 16Amp fuse unit is to be fixed to the MS angle / clamp and giving necessary connections with 14/0.3mm PVC copper flexible wire from pole to the fuse unit and to the fitting or from Ceiling rose in the building to the fuse unit and to the fitting with link clips etc., and the GI pipe has to be painted with two coats of enamel grey paint over one coat of red oxide paint. Fixing charges including the cost of MS angle, MS clamps, bending of pipe, bolts, nuts, fuse units etc.

Fixing of M.V / S.V /LED / M.H luminaire / Halogen fitting on wall / pole cross arm / channel / stem pipe etc., including all labour charges and giving connections etc., complete.

Supply and fixing of 34W Post top / street light luminaire with the following specification

a) Wattage : ˂34W LED(Tolerance allowed as per IS 16103)

b) SDCM : ˂5 c) Lumen output : ˃4000lm d) CRI (Ra) : ˃70 e) CCT: 3000K

f) Driver integral: Constant current g) Surge protection: ˃6kV SPD

h) The luminaire shall have Ingress protection of IP65

i) Housing: Pressure die cast Al j) Beam Angle : 120º

Note: The integral driver and the luminaire shall comply with the IEC standards or their Indian equivalents. The BIS certificates for both the luminaire and the driver has to be provided.

Makes: Philips-BS461 LED40/ Equivalent of Osram/ K-Lite.

Supply of 4.27 meters height decorative street/ garden light pole with Single Arm with Mild steel pipe with Zinc rich primer & Pure polyster powder coating and finishing with polyurethane based paint with all accessories such as suitable base plates, bolts & nuts etc, complete. Warranty: 5 years Make: Klite-KP5137

Supply and fixing of the surface mounted Up and Down wall washer luminaire with following specification.

a) Wattage : ˂12W LED(Tolerance allowed as per IS 16103)

b) SDCM : ˂5 c) Lumen output : ˃646 Lumens d) CRI (Ra) : ˃80 e) CCT: 3000K

f) The housing shall be of die-cast Aluminium & Polycarbonate Optical Lens diffuser. The luminaire shall have Ingress protection of IP65

g) Surge protection : ˃2kV h) Beam Angle : Narrow (˂50º) i) Warranty : 5 Years

Note: The integral driver and the luminaire shall comply with the IEC standards or their Indian equivalents. The BIS certificates for both the luminaire and the driver has to be provided.

Makes: Philips Radiant / K-lite KL7898/ Equivalent of Osram.

Supply and fixing of Surface mounted flexible LED strip (Excluding driver) of system power 12W/m with the following specification.

a) Wattage: ˂12W/m (Tolerance allowed as per IS16103)

b) SDCM: ˂5 for better colour consistency c) Lumen output : ˃800 Lumens /m d) CRI : ˃80 e) CCT: 3000K

f) The LED strip shall have a clear silicon encapsulation with ingress protection of IP65. g) Beam Angle : ˃110º

h) The LED strip shall be supplied along with the 40-50mm x 40-50mm x 2mm thick aluminium profile

Note: The integral driver shall be provided at remote location. The luminaire shall comply with the IEC standards or their Indian equivalents. The IEC/BIS certificates for the luminaire has to be provided.

Makes: Osram VFP1000 / Philips BGC201/ K-lite KL-7289

Supply and fixing of 24V Constant Voltage Driver of 150W, 230V AC input Voltage & 24V DC output Voltage surge protection ˃4KV with IP67 rated. Makes: Meanwell / Philips / Osram.

Supply and fixing of the surface mounted linear grazeer (Excluding driver) with the following specification.

a) The luminaire shall have dimensions 1005mm(L), 25mm(W), 332mm(H) and complete with the following specification

b) Wattage :˂20W/m (Tolerance allowed as per IS16103)

c) SDCM: ˂5 d) Lumen output: ˃1200 Lumens/m e) CRI : ˃80

f) Beam Angle : 30º g) CCT : 3000K h) Surge Protection: ˃2.5kV

i) The housing shall be of Extruded Aluminium with translucent end caps and clear polyurethane encapsulation diffuser.

j) The luminaire shall have impact protection of IK07 and ingress protection of IP67 k) Warranty : 5 years

Note: The Non-integral driver shall be provided at remote location as directd by the department. The luminaire shall comply with the IEC standards or their Indian equivalents. The IEC / BIS certificates for the luminaire has to be provided.

Makes: K-lite KL3557 / Equivalent of Philips/ Osram

Supply of 18/20W Surface/ recessed mounted down lighter with pressure die cast aluminium body, polycarbonate diffuser and steel clip (spring) with the following specification

Wattage : ≤20W SDCM :˂5 for better colour consistency Lumen output : ≥2000 Lumens Lumen Efficacy: ≥110lm /W(Tolerance as per BIS) CRI : ˃80 CCT : 3000/4000/6500K

Driver : Non-Integral THD : ˂10% PF : ˃0.9 Surge protection : +4 KV Protection: IP-20

Working life : ˃50000 Hrs Warranty : 5 Years Makes: Philips DN296 LED20S-3000/ 4000/ 6500 PUS WH or its equivalent.

Supply of 3 Core, 2.5 Sq mm ISI marked, PVC insulated and sheathed FRLS/FRLS-H round copper cable for voltage up to 1100V as per IS 694/1990 Makes: Finolex / RR kabel / Havells/ Finecab/ KEI/ Polycab/ Gloster/ Goldmedal/ GM/ Fortune Arrt/ Anchor /Million

Rupees Five Crore Eighteen Lakh(s) Thirty Four Thousand Sixteen And Paise Thirty Five Only

PART-B(Open tender items)

For the supply & installation of 80mm puff panels . Specs : Top sheet & bottom sheet 0.50 mm TCT PPGL AZ 150 GSM ,Tensile strength:550 MPA .(As per your specifications)

Technical specifications of insulation: 1).CFC & HCFC FREE RIGID Polyurethane foam. 2).Foam thermal conductivity at (k-value) At 10°C mean temp = 0.023 W/m°k. 3)Compressive strength= 4.35kgper /sqcm. 4)Closed cell contents = 90% - Min 5)Horizontal burning characteristics = 125mm-max, Fire retardent, self existinguishing quality foam. 6) Fire properties As per DIN 4102 = B3 7) water absorption= 0.2volume at 100% RH -MAX 7) Vapour permeability = 0.24 ng/ pasm at 88% RH & 38° C MAX. 8) Dimensional stability at +70° C temp = + or - 2% . 9) -25° C temp= + or - 2% (excluding GST)

Fabrication and supply of stainless steel 3 seater Bench with back rest (conforming to SS-304 grade, satin finish) consisting of pipes 38mm dia,1.60mm thick,19 mm dia, 1.6 mm thick, frame box sections 60x40x2mm thick, frame stiffeners 3mm thick, base plate 6mm thick, chair sheets 1.60mm thick with fasteners (Canco / Boun / Equivalent make) with minimum weight of the Bench at 40 Kgs and as per the sample approved by the competent authority including cost and conveyance all taxes etc., but excluding cost of GST complete.