31/28976/2024_26_1_1

OD172277/2024-2025:1. Pumpset - Design, supply, erection, testing, trial run and commissioning of KWA prequalified reputed make open well type submersible pump set with bronze/SS impeller, SS shaft and CI pump complete. The duty condition is as follows: Tentative Discharge-. 50 lps against a total head-40 m, (The actual discharge and head are to be assessed after conducting necessary ETS/DGPS survey followed by hydraulic modelling using software like EPANET and the design is to be approved by the Engineer-in-Charge before procurement order is placed). The speed, efficiency etc. should be conforming to KWA norms and as directed by the officer in charge. 2. Motor - Supply, erection, testing and commissioning of KWA prequalified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump set working 3 phase, 40HP, 50 Hz , 415 V working in AC supply. The motor shall confirm to ELFI/IS 325 . 3. Starter - Supply erection, testing and commissioning of suitable rating Fully automatic starter for the above motor with over voltage and under voltage protection , single phase preventer , over load relay with motor protection relay complete . 4. Panel board ( suitable for operating two pump sets but one pump set at a time ) - Supply, erection and commissioning of cubical type MS fabricated dust and vermin proof common control panel board consisting of 1 no. suitable capacity MCCB as incomer and 2 nos of suitable capacity MCCB as out going , providing suitable size Aluminum bus bar , 3 nos of indicator lamps , 1 no Volt meter with selector switch , Ammeter with selector switch etc complete the panel shall be fitted on a common base frame on suitable foundation . 5. Cabling work-Supply, laying ,testing and commissioning of suitable size XLPE cable for the above pump set from panel board to starter and from starter to motor. 6. Capacitor- Supply ,erection testing and commissioning duty APP capacitor for the motor to get a power factor above 0.95 . The capacitor shall confirm to IS 2834. 7. Valves- Supply of suitable size best quality heavy duty ISI marked double flanged sluice and Non return valves with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valve. 8. Suction and delivery pipe connections-Supply and fitting of suitable size best quality GI/MS pipe of thickness not less than 8mm for the above pump set for connecting the delivery side of the pump with valves and suitable specials to connect with the existing pumping main. 9. M-power unit with Automation Module suitable for the above pump set. 10. Earthing with GI earth pipe 4.50 m long 40 mm dia including accessories. 11.Conditions : Including Maintenance for a period of Five years. (Rates as per CE (Projects) KWA Proceedings no. 10636/AE 15/2022/KWA dated 29.03.2023).

OD172390/2025-2026:1. Pumpset - Design, suply, erection, testing, trial run and commissioning of KWA pre qualified reputed make tube well submersssible pump set with Bronze/SS impeller, SS shaft and CI pump. The duty condition is as follows: Tentative Discharge-. 12 lps against a total head-111 m, (The actual discharge and head are to be assessed after conducting necessary ETS/DGPS survey followed by hydraulic modelling using software like EPANET and the design is to be approved by the Engineer-in-Charge before procurement order is placed). The speed, efficiency etc. should be conforming to KWA norms and as directed by the officer in charge. 2. Motor - Suply, erection, testing and commissioning of KWA prequalified reputed make horizondal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump set working 3 phase, 40HP, 50 Hz , 415 V working in AC supply. The motor shall confirm to ELFI/IS 325 . 3. Starter - Supply erction, testing and commissining of suitable rating ( Fully automatic FCMA) starter for the above motor with over voltage and under voltage protection , single phase priventer , over load relay with motor protection relay complete . 4. Panel board ( suitable for operating two pump sets bunt one pump set at a time ) - Suplly, erection and commissioning of cubicatype MS fabricated dust and vermin proof commen control pannel board cosisting of 1 no. suitable capacity MCCB as incommer and 2 nos of suitable capacity MCCB as out going , providing suitable size Aluminium bus bar , 3 nos of indicator lamps , 1 no Volt meter with selector switch , Ammeter with selector switch etc complete the panel shall be fitted on a commen base frame on suitable foundation . 5. Capacitor- Supply ,erection testing and commissioning duty APP capacitor for the motor get a power factor above0.95 . The capacitor shall confirm to IS 2834. 6 Cabling work-Suplly, laying ,testing and commissining of suitable size XLPE cable for the above pump set from panel board to starter and from starter to motor. 7. Valves- Supply of suitable size best quality heavy duty ISI marked double flanged sluice and Non return valves with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valve. 8. Delivery pipe connections-Supply and fitting of suitable size best quality GI/MS pipe of thickness not less than 8mm for a total length of 10 meter suitable for the above pump set and valves with suitable flanges, nut and bolts, IR sheet etc complete and connecting the delivery side of the pump with valves and suitable specials to connect with the pumping main. 9.Conditions : Including Maintanance for a period of Five years. Say 25 HP tube well submerssible pumpset ( rate included above motor, pump,starter, panel,cable,earthing, capacitor, valves suction and delivery line) (Rates as per CE (Projects) KWA Proceedings no. 10636/AE 15/2022/KWA dated 29.03.2023).

OD172421/2025-2026:Supply of additional 3 core flexible cable suitable size and capacity for working of the specified pump set

OD172215/2025-2026:1. Pumpset -Design, supply, erection, testing, trial run and commissioning of KWA pre qualified reputed make tube well submersible pump set with Bronze/SS impeller, SS shaft and CI pump. The duty condition is as follows: Tentative Discharge-. 10 lps against a total head-130 m, (The actual discharge and head are to be assessed after conducting necessary ETS/DGPS survey followed by hydraulic modelling using software like EPANET and the design is to be approved by the Engineer-in-Charge before procurement order is placed). The speed, efficiency etc. should be conforming to KWA norms and as directed by the officer in charge. 2. Motor - Supply, erection, testing and commissioning of KWA prequalified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump set working 3 phase, 40HP, 50 Hz , 415 V working in AC supply. The motor shall confirm to ELFI/IS 325 . 3. Starter - Supply erection, testing and commissioing of suitable rating ( Fully automatic FCMA) starter for the above motor with over voltage and under voltage protection , single phase preventer , over load relay with motor protection relay complete . 4. Panel board ( suitable for operating two pump sets bunt one pump set at a time ) - Supply, erection and commissioning of cubical type MS fabricated dust and vermin proof common control panel board consisting of 1 no. suitable capacity MCCB as incomer and 2 nos of suitable capacity MCCB as out going , providing suitable size Aluminum bus bar , 3 nos of indicator lamps , 1 no Volt meter with selector switch , Ammeter with selector switch etc complete the panel shall be fitted on a common base frame on suitable foundation . 5. Capacitor- Supply ,erection testing and commissioning duty APP capacitor for the motor get a power factor above0.95 . The capacitor shall confirm to IS 2834. 6 Cabling work-Supply, laying ,testing and commissioning of suitable size XLPE cable for the above pump set from panel board to starter and from starter to motor. 7. Valves- Supply of suitable size best quality heavy duty ISI marked double flanged sluice and Non return valves with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valve. 8. Delivery pipe connections-Supply and fitting of suitable size best quality GI/MS pipe of thickness not less than 8mm for a total length of 10 meter suitable for the above pump set and valves with suitable flanges, nut and bolts, IR sheet etc complete and connecting the delivery side of the pump with valves and suitable specials to connect with the pumping main. 9.Conditions : Including Maintenance for a period of Five years. Say 25 HP tube well submerssible pumpset ( rate included above motor, pump, starter, panel, cable, earthing, capacitor, valves suction and delivery line) (Rates as per CE (Projects) KWA Proceedings no. 10636/AE 15/2022/KWA dated 29.03.2023).

OD172420/2025-2026:Supply of additional 3 core flexible cable suitable size and capacity for working of the specified pump set

OD172423/2025-2026:suitable size uPVC vertical column pipe for submersible pump erection.