PROVN OF DEFFI MD ACCN AT GANDHINAGAR MIL STN

Lump sum price worked out by the contractor for "BUILDING WORKS" as listed in Schedule ‘A’ Part-I representing percentage (+ or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES .

Lump sum price worked out by the contractor for "SITE CLEARANCE, EXCAVATION & EARTH WORK" as listed in Schedule ‘A’ Part-II representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "INTERNAL WATER SUPPLY WORKS " as listed in Schedule ‘A’ Part-III representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "INTERNAL ELECTRIFICATION WORKS" as listed in Schedule ‘A’ Part-IV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for " ROAD/FOOT PATH/ CULVERT WORKS " as listed in Schedule ‘A’ Part-V representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "AREA DRAINAGE WORKS" as listed in Schedule ‘A’ Part-VI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "SEWAGE DISPOSAL WORKS" as listed in Schedule ‘A’ Part-VII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES

Lump sum price worked out by the contractor for " COMPOUND WALL , FENCING AND STEEL GATE WORKS" as listed in Schedule ‘A’ Part-VIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "EXTERNAL WATER SUPPLY WORKS" as listed in Schedule ‘A’ Part-IX representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "EXTERNAL ELECTRIFICATION WORKS" as listed in Schedule ‘A’ Part-X representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Sch 'A' PART-XI (MISCELLANEOUS ITEMS) Notes: (i) This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only. (ii) Excavation and earth work except for the items which categorically includes for same shall be measured and paid separately under respective schedule.

SITE CLEARANCE, EXCAVATION & EARTH WORK Supply only approved earth obtained from outside the proposed land including transportation and cost of earth and deposited as directed.

INTERNAL WATER SUPPLY S&F of 15 mm bore fancy type chromium plated bib cock with wall flange, screwed for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make- Jaquar cat part no VGP-81037 or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of 15 mm bore fancy type chromium plated central hole basin mixer with popup waste system with 450 mm long braided hoses for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make- Jaquar cat part no CON169KNB or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of 15 mm bore fancy type chromium plated angular stop cock screwed for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make- Jaquar Queen series cat part no QQT-7053 or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of of CP wall mixer 3 in 1 with provision for hand shower and overhead shower including 1.5 mtr long tale shower screwed for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make- Jaquar Queen series cat part no QQT-7281 or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of 15 mm bore fancy type chromium plated single lever sink mixer with swinging spout on upper side (wall mounted model) with connecting legs and wall flanges and fixed complete all as specified and directed. Make- Jaquar cat part noFON-40165 or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of overhead shower 150x150mm of square shape single flow with rubit cleansing system ABS body cromted plated with grey face plate with arm having swivel joint chromium plated complete all as specified and directed. Make- Jaquar cat part no OHS-35495 or equivalent as makes given at Appx 'C' (For Officers Accn)

S&F of health faucit with 1200 mm long flexible mild steel tube 15 mm dia with wall hook and complete all as specified and directed. Make- Jaquar cat part no ALD-573 or equivalent as makes given at Appx 'C' (For Officers Accn)

Supply and fixing of 15 mm dia two way chromium plated bib cock complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.

S&F of 15 mm bore fancy type chromium plated bib cock with wall flange, screwed for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(SERVANT MD ACCN )

S&F of 15 mm bore fancy type chromium plated sink cock with swinging spout (wall mounted model) with wall flange and fixed complete all as specified and directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(SERVANT MD ACCN )

S&F of 15 mm bore fancy type chromium plated angular stop cock with wall flanged screwed for iron pipe or CPVC pipes or for brass ferrules and fixed complete all as specified and directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(SERVANT MD ACCN )

Supply and fixing of 15 mm bore Overhead shower of 114 x 114 mm of square shape single flow with rubit cleaning system ABS body crome plated with grey face plate with arm having swivel joint chromium plated complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(SERVANT MD ACCN )

S&F of health faucit with 1000 mm long flexible mild steel tube 15 mm dia with wall hook and complete all as specified and directed Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For JCO Md Accn)

Supply and fixing of 15 mm bore fancy type chromium plated bib taps with wall flange,screwed for iron pipe or CPVC pipes or for brass ferrule and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

Supply and fixing of 15 mm bore fancy type chromium plated pillar cock swan neck tap with right hand operating knob and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

Supply and fixing of 15 mm bore fancy type chromium plated pillar cock swan neck tap with right hand operating knob and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

S&F of 15 mm bore fancy type chromium plated sink cock with swinging spout (wall mounted model) with wall flange and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

S&F of 15 mm bore fancy type chromium plated angular stop cock screwed for iron pipe or CPVC pipes or for brass ferrules and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

Supply and fixing central hole bas

Supply and fixing of 15 mm dia fancy type chromium plated angular stop cock screwed for iron pipe or CPVC pipes or for brass ferrule and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For OR Md Accn)

in mixer with regular spout with popup waste system wiyh 450 mm long braided hoses and fixed complete all as specified and as directed. Make: Jaquar Queen series cat part no QQT-7167B or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

S&F of of CP wall mixer 2 in 1 with provision with central spout and connection for overhead shower with diverter liver ISI marked complete all as specified and directed. Make- Jaquar Queen series cat part no QQT-7281 or equivalent as makes given at Appx 'C' (For JCO Md Accn)

Supply and fixing of Overhead shower of 114 x 114 mm of square shape single flow with rubit cleaning system ABS body crome plated with grey face plate with arm having swivel joint chromium plated complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For JCO Md Accn)

S&F of 15 mm bore fancy type chromium plated bib cock with wall flange, screwed for iron pipe or cpvc pipes or for brass ferrule and fixed complete all as specified and directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For OR Md Accn)

Supply and fixing of 15 mm bore fancy type chromium plated pillar cock swan neck tap with right hand operating knob and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For OR Md Accn)

Supply and fixing of 15 mm bore fancy type chromium plated concealed stop cock, reduced body with adjustable wall flanged and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C'.(For JCO Md Accn )

Supply and fixing of 15 mm bore fancy type chromium plated concealed stop cock, reduced body with adjustable wall flanged and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For OR Md Accn)

S&F of 15 mm bore fancy type chromium plated sink cock with swinging spout (wall mounted model) with wall flange and fixed complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For OR Md Accn)

Supply and fixing of 15 mm bore two way chromium plated bib cock complete all as specified and as directed. Make - Jaquar/Essco Series or equivalent of any make specified in Appx 'C' (For JCO Md Accn)

S&F of of CP wall mixer 2 in 1 with provision with central spout and connection for overhead shower with diverter liver ISI marked complete all as specified and directed Make - Jaquar Queen Series cat part no- QQT-7281 or equivalent of any make specified in Appx 'C' (For OR Md Accn)

Supply and fixing 15 mm bore fancy type chromium plated central hole basin mixer with popup waste system wiyh 450 mm long braided hoses for iron pipe or CPVC pipes or for brass ferrule and fixed complete all as specified and as directed Make - Jaquar Queen Series cat part no- QQT-7176B or equivalent of any make specified in Appx 'C' (For OR Md Accn)

INTERNAL ELECTRIC SUPPLY Supply and fixing of MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, load line distribution board TPN vertical, 4 way with 200 Amps rated bus bar , 415 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof including MCCB 125 Amps, 4P, 16 kA as incomer etc complete all as specified and as directed.

Supply and fixing TV sockets complete with all accessories all as specified and as directed by Engineer-in-Charge.

Supply and fixing RJ 11 Gang with shutter (Telephone Jack) complete with all accessories all as specified and directed by Engineer-in-Charge

Supply & fix PVC metal braided connection pipes for geyser for hot/cold water supply with brass adopters 15 mm dia and 450mm long complete all as specified and as directed.

Supply & fix LED bulb B22 base 9 W, min lumen output 950 lumens at 6500 K CCT for batten holders complete all as specified and as directed.

Supply & fix LED wall light with bulb of PVC Shade Contemporaty decorative lighting indoor wall lamp fixture for bedroom, Living room B22 base 10 W, min lumen output 950 lumens at 6500 K CCT for batten holders complete all as specified and as directed.

M & L for inverter point wiring for one light, ceiling fan and 5 Amp socket for each room with 2.5 sqmm,PVC insulated, unsheathed, single core multistandard copper conductor cable ( FRLS), 1100 volts grade including 2.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories upto the main DB and 15 A switch socket combination with gang box flushed in wall for inverter power supply complete all as specified and as directed.

S & F LED security light fitting 60 W made out of pressure die cast aluminium powder coated housing high impact resistant 4mm thick toughened glass cover and matrix of power LEDs inbuilt electronic driver up to 4KV surge protection fitted with adjustable pole adapter to enable on site tilt angle setting depending on road geometry CCT5500-6500 CRI greater than 70 , input power 24W system with 85W/ lumens output operating voltage 140-280V with connection by three core PVC insulated multistranded copper conductor sheathed cable of size 2.5 sq mm fixed with & including bracket made of GI pipe 40mm bore light grade, 1.6 mtr long bent to shape required with 2 no MS clamps of suitable size and length, nuts & bolts complete all as specified and as directed.

M & L for drawing 12 pair /multi core 22 AWG,foil shilded , copper coated telephone cable including PVC conduit of size 20mm complete all as specified & directed .

S&F Wall mounted fan 250mm sweep, 5 star rated with speed regulater,180 degree rotated , 900 rpm, double ball bearing ,all including connection with single core PVC insulated but unsheathed, FRLS cable with multistranded copper conductors IS 694 marked, from ceiling rose to fan complete all as specified and directed.

COMPOUND WALL , FENCING AND STEEL GATE WORKS S & F of CI wheel as rollers of 75mm dia for gates.

M & L pre stressed pre cast RCC (M-25 grade) column cross section 150 mm x 150 x 2400 mm with contineous vertical grooves of size 60 mm x 35 mm at two sides of column to receive the precast panels including reinforced with 7 nos wires of 3 mm dia high tensile corbonized steel surfaces finished even and smooth including errecting in position all as specified and as directed.

M & L pre stressed pre cast RCC (M-25 grade) panels of cross section of panel (300X45 mm) reinforced with 4 nos wires of 3 mm dia high tensile corbonized steel, including fixing in position in between column grooves and jointing and flush pointing of all horizontal and vertical joints of panels with cement mortar 1:3 complete all as specified and as directed.

EXTERNAL ELECTRIFICATION WORKS Supply, install, testing and commissioning including transportation at site 12 KV , 630 Amp 21 KA- 3 Sec, 3 way non-extenble outdoor type SF6 gas insulated ring main unit with one direct cable module and two LBS ( Load Break Switch ) Configuration DCC Active load - 630 Amp, Closed Loop - 630 Amp, Off Load Cable Charging 135 Amp, Earth fault 200 Amp, Earth fault Cable Charging 115 Amp short circuit making capacity 52 Amp equipped with external bushings which comply with DIN47636T1 & T2/EDF HN 525-61 for termination of cables,All bushings are situated in the same height from the floor and are protected by the cable cover, Installing current transformers. The cable shielding is led back through the centre hole and earthed ,Voltage presence indication system (VPIS) including all accessories and mountings provided by manufacturer with mounting base frame / plateforn complete in all respect techinical approcval is required with all technical data and control drawings from accepting officer before incorporation in work of Make ABB/ Siemens// Schnieder

Supply and fixing HT Junction Box 3 way ,11000 Volts grade with 3 mm CRCA outdoor F with busbar enclosure7- tank pre-coat process powder coated hardware gasket locking arrangements of sixze 1200(H)x900(W)x500(D) in mm with stand complete all as specified and directed

M&L for boring of holes under road, pavement, hard standing by trenchless technology using HDD augaring technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed

Supply, installation, commissioning and testing of Main LT panel , size suitable to accomdate mentioned accessories , factory made (CPRI approved) indoor cubical compartmental type double door both side openable with hinged doors & locking arrangement made out of not less than 3.15 mm thick mild steel CRCA sheet outerbody and 2m thick for ineterior chambers etc duly powder coated supported and fixed on structural frame of angle iron of size 50 x50 x6mm angle iron frame including earthing stud lebeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 stage process), duly fixed in ground with PCC foundation (1:2:4) type B1 with danger notice plate of 1.6mm thick mild steel sheet, vitrious enamelled (white) with letters figures and conventional skull and bones in signal red colour suitable for 3 phase 4 wire system 500Volts grade with necessary wiring with PVC sheathed strander al conductor of appropriate length size with and including fixing lugs bolts, screws etc complete all as specified and directed. For safety , panel shall be finger touch proof and it should have IP-20 Protection in module door open condition.Busbars shall be made of high conductivity, and high strength Aluminum E91 grade as per IS 5082-1981, of rectangular cross sections better suitable for full load current for phase bus bars and half/ full rated current for neutral bus bar or as per requirement . The busbars shall be supported on non-breakable, non-hygroscopic epoxy resin or glass fiber reinforced polymer insulated supports.The material and the spacing of the Busbar supports should be same as per the type tested assembly (TTA). All bus bars shall be provided in a separate chamber and all connections shall be done by bolting. Panel comprising of the following accessories :- Incoming (a) Incoming MCCB of capacity 400 A, 4 P, 36 KA (b) Aluminium busbar of rated capacity 630 Amps cover with PVC insulated sleeves including insulator, nuts, bolts etc incl connection complete - 01 set (c) Neon indicator lamp with holder (Yellow, Blue,Red)- 01 set (Set of three) (d) Digital VAF meter with suitable CTs - 01 No. Out Going: (i) MCCB 4 pole 415 Volts of breaking capacity of 36 KA of 200 Amps with Microprocessor based over load Protection -06 No (ii) MCCB 4P 415 V ,36 kA of 160 A with thermal overload protection - 01 No (iii) Street light timer with MCB 20 Amp along with necessary relays and power contactor etc.

Supply, installation, commissioning and testing, feeder pillar board, LT (415 Volts, 50 Hz , 3-phase, 4 wire supply),CPRI approved, plinth mounted, factory made, outdoor type, weather and vermin proof (Protection Class IP-54) made out of 50mm x 50mm x 5mm angle iron frame and 3.15 mm thick mild steel CRCA sheet outerbody and 2m thick for ineterior chambers etc powder coated with front & back hinged opening, rubber lining, locking arrangement, painted externally and internally with two coats of synthetic enamel gray paint (First Quality) over a coat of red oxide primer, grouting panel through angle iron, 0.2 mtr in gro

und and 0.5 mtr over the ground including excavation & earth work in any type of soil and PCC (1:3:6) type C-2 using 40mm graded stone aggregate complete comprising of the followings:- (a) Incoming supply:- (i) Aluminium bus bar chamber 200 amps rating of 04 strip - 01 No (ii) MCCB, thermal and magnetic setting, 4 pole, AC, 415volts,200 Amp rating, 36 KA rupturing capacity - 01 No (iii) Multifunction meter showing PF, V, I, Hz, Etc (iv) Indicating lamp Neon type for R-Y-B - 3 Nos (b) Outgoing supply:- (i) MCCB, thermal and magnetic setting, 3 pole, AC, 415volts,100 Amp rating, 25KA rupturing capacity - 05 Nos Complete all as specified and directed by Engr-in-Charge

M&L for HT cable route indicator duly painted with grey colour synthetic enamel paint two coats over one coat of red oxide primer, oval shape of size 200mmx150mmx6mm thick cast iron disc with letters embossed and fixed on 25mmx25mmx5mm thick MS angle iron for 50mm long including necessary PCC in 1:3:6 type C1 cement concrete 20mm aggregate and 15mm thick plastering all around below ground level of size 650mmx300mmx250mm embedded in PCC block all as specified.

S&F metal junction box, factory made, with one No SP MCB of 20 Amp rating, class-B and 3 Nos connector fixed on pole with necessary clamps and bolts etc including connecting with street light cable complete all as specified and directed. nd length, nuts & bolts complete all as specified and as directed.

S&F PVC insulated and PVC sheathed ,ISI marked copper conductor cable of size 1.5 Sqmm, 3 core, 1100 volts grade,conferming to IS:694, multistranded, passing throuth pipe, on pole/wall from juntion box to street light fitting complete all as specified and directed.

EXTERNAL WATER SUPPLY WORKS Supply, laying, connecting, jointing and testing of DI pipe with spigot and socket ends, class K-7 conforming to IS: 8329/2000 suitable for (push-on) rubber gasket jointing with centrifugally applied inside cement mortar lining with sulpher resistant with a finishing layer of black bitumen coating on external surfaces in any length, laid in trenches complete all as specified and as directed of the sizes 150 mm. including EPDM gasket complete of make kejriwal, tata, electrosteel shreekalahashti .

Supply, laying, connecting, jointing and testing of DI pipe with spigot and socket ends, class K-7 conforming to IS: 8329/2000 suitable for (push-on) rubber gasket jointing with centrifugally applied inside cement mortar lining with sulpher resistant with a finishing layer of black bitumen coating on external surfaces in any length, laid in trenches complete all as specified and as directed of the sizes 100 mm. including EPDM gasket complete of make kejriwal, tata, electrosteel shreekalahashti .

S&F DI sluice valve 150 mm dia with flanged ends class PN-1.6 with iron wheel, stainless steel spindle and check nut confirming to IS :14846 including all jointing materials such as nuts, bolts, washers and gaskets etc. complete all as specified & directed .

S&F, DI sluice valve 100 mm dia with flanged ends class PN-1.6 with iron wheel, stainless steel spindle and check nut confirming to IS :14846 including all jointing materials such as nuts, bolts, washers and gaskets etc. complete all as specified & directed .

S&F DI sluice valve 80 mm dia with flanged ends class PN-1.6 with iron wheel, stainless steel spindle and check nut confirming to IS :14846 including all jointing materials such as nuts, bolts, washers and gaskets etc. complete all as specified & directed .

M&L for construction of valve pit chamber of size 1350 mm x1000 mm x1200 mm consisisting of 230mm thick, old size brick masonry wall in cement mortar (1:6), PCC (1:4:8) type D2, using 40mm graded stone aggregete as in fondation, PCC (1:2:4) type B1, using 20mm graded stone aggregete in coping/bed, finished even and smooth, rendering 15mm thick in cement mortar (1:6) internally and 10mm thick in cement mortar (1:4) externally, finished even and smooth without using extra cement incuding three coats of white wash and earth work in any type of soil and including 16 gauge thick MS sheet cover fixed on 40mmx40mmx6mm thick angle iron frame ambeded in PCC coping with locking arrangement and mild steel hold fast & handle and duly painted with two coats of synthetic enamel paint over one coat of primer etc. and as specified and directed

M&L for construction of valve pit chamber of size 450 mm x450 mm x750 mm consisisting of 230mm thick, old size brick masonry wall in cement mortar (1:6), PCC (1:4:8) type D2, using 40mm graded stone aggregete as in fondation, PCC (1:2:4) type B1, using 20mm graded stone aggregete in coping/bed, finished even and smooth, rendering 15mm thick in cement mortar (1:6) internally and 10mm thick in cement mortar (1:4) externally, finished even and smooth without using extra cement incuding three coats of white wash and earth work in any type of soil and including 16 gauge thick MS sheet cover fixed on 40mmx40mmx6mm thick angle iron frame ambeded in PCC coping with locking arrangement and mild steel hold fast & handle and duly painted with two coats of synthetic enamel paint over one coat of primer etc. and as specified and directed

Supply, installation, testing and commissioning of submersible pump electrical driven 415 Volt TP Horizontal type, suitable for Sump of Capacity 100000 ltr 15-20HP, with min head 36 mtr maxximum head 65 mtr, Discharge pipe 100-150 mm with discharge capacity 70000 Ltr/ hour complete with motor and pump wit all accessories and mounting.

Supply, installation, and testing of submersible flat copper cable 10 Sqmm 3 Core Size,PVC insulated & PVC sheathed suitable for submersible pump motor 1100 volt grade ,ISI marked conferming to IS 694 complete all as specified and directed

S&F cast iron air release valves with single air outlets conforming to IS 14845 of size 50 mm dia bore , ISI marked and fixing in DI water supply pipe of size 150 mm dia complete all as specified and directed

Supply, install, testting and commisioning of LT MCC panel box company fabricated, outdoor type made out of MS CRCA sheet 3.15mm thick with angle iron frame 50x50x6mm floor mounted support suitable for 3 phase 4 wire 50 HZ, 500V system weather and vermin proof double door including front and back opening, all internal connections incoming to outgoing with BUS BAR, chromium plated brass cable glands painting with a coat of redoxide primer and powder coated paint of approved colour and make complete with structure, insulators, nuts and bolts, washers etc includng PCC for fixing and consisting of the following :- (a) MCCB incoming , 160 Amps, 415 volts (for incoming) 35 KA-01 No (b) Bus bar with copper strip of capacity 200 Amps for 3 phase and neutral system with CTs - 01 Set (c) Digital panel meter for volt, Amp, KWH, PF and other parameter flush mounting of size 96 x 96mm Make : Secure/AE/Conzerv (d) MPCB, 4 pole TPN, 100 Amps, 415 Volts (for outgoing) 35 KA - 03 Nos with Soft Starter-03 Nos (e) MCB SPN 20 Amps, 415 Volts (for outgoing) 10 KA - 01 No (f) Internal fine wiring with suitable size and rating of wire

M&L for cutting of existing steel tubing at two place of Size 150 mm for insertion of tee for extension of water supply pipe line for Md Accn including tee 150x50x150 two end socketed and one end of 50 mm flanged complete all as specified and as directed.

M&L for cutting of existing steel tubing at two place of Size 150 mm for insertio

n of tee for extension of water supply pipe line for Md Accn including tee 150x80x150 two end socketed and one end of 80 mm flanged complete all as specified and as directed.

ARBORICULTURE Digging of pit n.exc 0.25 cum in any type of soil incl removal and filling back to pit with suitable growing media like red earth by treating with farm yead manure in the ratio (3:1) fertilizers and pesticides (i.e Bevation and neem cake BHC 10% linson dust. Thimment or phorate, manures super and vermicompost) and making up the trenh area to proper level including supply and planting tree plants of species of height not less than 4 ft for following trees :- (a) Polyantha long folia (Ashoka) = 10.00 Nos (b) Polyantha long folia Guava, Jamun, Mango = 20.00 Nos (c) Phoenix dactyliferous (Palm) = 10.00 Nos Total = 40.00 Nos

Prvn of M.S Tree Guard 1.50 Mtrs high above with MS wiremesh of size 78 x 37 mm and 2 mm dia of wire and MS angle iron 20 x 20 x 3 mm verticals (3 Nos) & MS flats 14 x 3 mm around the tree guard (3 Nos top , middle and bottom) equally spaced and embedded vertical angles in PCC 1: 3:6 Type B-I including excavation in post holes and removal of excavated material to a n.exc 5 mtr and applying two coats of synthetic enamel paint including one coat of red oxide primer to tree guard and all as specified and directed.

Services for maintenance of planted trees covered under Phase-I (i) including watering the plant thrice a week having each irrigation of 10Litres (ii) hoeing or loosening of soil after every 30 days (iii) weeding, pruning, removal of garden rubbish (iv) spraying of insecticides, pesticides (like Monocrotophus, Miticide, Rogor etc) after every 60 days using 25ml in 15 litres of water or using Methyl parathion or Furadan mixed in powder form with earth using 50gm per tree (v) applying manure vermin-compost, neem cake & micro nutrients mixed with the earth in the ratio of 1:4 etc as per standard procedure and as directed by Engr-in- charge/GE, protecting the trees and shrubs, keeping good health of the plants so as to keep the plants live in entire period of 24 months and replacing the dead trees and shrubs with the size as per time grown new live trees & shrubs (with in 48 hours) etc.