Annual Plan-2022-23 Kesavapuram CHC-Kilimanoor BP - Maintenance of Kesavapuram CHC-General Civil Work

Amount

Building Maintenance

21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

21.1.2.1:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

OD97138/2022-2023: Providing and fixing 8 mm thick Laminated Compost Panel board in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge. Pre- laminated particle board with decorative lamination on both sides.

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

OD103162/2022-2023: Full Partitions - Supplying and fixing partitions with 18mm thick ply wood grid and covering with 10mm thick ply and fixing with heatex fevicol and again covering with 1 mm thick mica and fixing with heatex fevicol complete as per the directions of EnC

OD103727/2022-2023: Half Partitions - Supplying and fixing partitions with 18 mm thick ply wood grid and covering with 10 mm thick ply and fixing with heatex fevicol and again covering with 1 mm thick mica and fixing with heatex fevicol complete as per the directions of EnC

OD103728/2022-2023:od209907/2019_2020 : Providing and fixing 12 mm frame less thick toughened glass door shutters of approved makes(size of door 2.1 x1.1m)

OD103174/2022-2023: Type II- Supplying and fixing 18 mm MDF using Hard Wood prelaminated an approved brand and manufacturer placed vertically and horizontal at external faces and as per specification.Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade-I MDF Board 18mm thick confirming to IS:14587 of size 1500x750x750mm. The table shall have a height of 750 mm. as directed by the engineer in charge.

OD103165/2022-2023: Type I- Supplying and fixing 18 mm MDF using Hard Wood prelaminated an approved brand and manufacturer placed vertically and horizontal at external faces and as per specification.Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade-I MDF Board 18mm thick confirming to IS:14587 of size 1210x600x750mm. The table shall have a height of 750 mm. as directed by the engineer in charge.

OD103160/2022-2023:od209907/2019_2020 : Providing and fixing 12 mm frame less thick toughened glass for partition of approved makes(0.5x0.45m)

OD103170/2022-2023:Supplying and fixing cup boards using 18 mm thick prelaminated boards with size 1.04x1.65x.53 with double door and 2 nos locks and handles

OD103161/2022-2023:Supplying and fixing cup boards using 18 mm thick prelaminated boards with size 0.75x 0.60 x 0.50m with double door and 2 nos locks and handles

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

60.7.1:DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.2.2:Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.25.2:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

11.20.4:Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Ordinary cement without any pigment

18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

50.18.9.14.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

2.28.1:Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

16.68:Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

ADHILKAHAN

NANDU

NAZARUDEEN

laldinga

Bidder Name

GURUDAS.S

NAZARUDEEN

laldinga

ADHILKAHAN

NANDU