PROVISION OF 40 ORs SINGLE ACCN FOR FIELD HOSPITAL AT JOSHIMATH.

Amount

SCHEDULE 'A' PART-I (BUILDING WORK)

Construction Block of single accomodation (triple storey) for 37 ORs & 03 HAVs and common/ study room complete all as shown in drawings and specified.(Group-II Building)

Total amount of SCHEDULE 'A' PART-II (INTERNAL WATER SUPPLY) (For details see Schedule 'A' Part-II in PDF folder)

Total amount of SCHEDULE 'A' PART-III(A) (INTERNAL ELECTRIFICATION) (For details see of Schedule 'A' Part-III-A in PDF folder)

SCH 'A' PART-III(B) (INTERNAL ELECTRIFICATION)

M&L for point wiring (concealed) complete using approved colour coding as per IS (Red, Black, Green for single phase circuit) with multi-stranded copper conductor 1.5 Sqmm nominal cross section area, single core PVC insulated unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including PVC conduit medium grade conduit accessories such as bend, tee, junction boxes elbows etc, ISI marked with valid CML No. (IS :9537 -1983 for conduit and IS :9537 -1976 for conduit accessories) including pressed steel terminal sunken boxes 1.6 mm thickness, 65mm deep with earth dolly, duly painted with two coats of black bitumenous paint over a coat of red oxide primer externally, covered with 3mm thick plastic laminated sheet ISI marked top cover fixed with Brass screws, cup washers and PVC unsheathed copper conductor 1.5 Sqmm cross sectional area, single core FRLS cable as earth continuity wire connetctd to DBs/sunken boxes/fittings conductor and all other metal parts with earth dolly complete all as specified and directed for the following:-

One light point controlled by one switch 5/6 Amp

One fan/exhaust fan point controlled by one switch 5/6 Amp

One light point controlled by two Nos two way switches 5/6 Amp

One 5/6 Amp socket point controlled by one switch on the same board.

One 5/6 Amp socket point controlled by one switch independent board.

M&L for point wiring (concealed) complete using approved colour coding as per IS (Red, Black, Green for single phase circuit) with multi-stranded copper conductor 2.5 Sqmm nominal cross section area, single core PVC insulated unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including PVC conduit medium grade conduit accessories such as bend, tee, junction boxes elbows etc, ISI marked with valid CML No. (IS :9537 -1983 for conduit and IS :9537 -1976 for conduit accessories) including pressed steel terminal sunken boxes 1.6 mm thickness, 65mm deep with earth dolly, duly painted with two coats of black bitumenous paint over a coat of red oxide primer externally, covered with 3mm thick plastic laminated sheet ISI marked top cover fixed with Brass screws, cup washers and PVC unsheathed copper conductor 2.5 Sqmm cross sectional area, single core FRLS cable as earth continuity wire connetctd to DBs/sunken boxes/fittings conductor and all other metal parts with earth dolly for one three pin 15/16 Amp, socket out let point on independent board complete all as specified and directed.

M&L for Distribution board SPN 8 way, double door for mounting MCBs/Isolator, ELCBs etc factory made conforming to IS:13032 fabricated with CRCA sheet dust and vermin proof not less than 1.2mm thick fitted with DIN channel, neutral link and 200 Amps rated copper bus bars, IP-42 protection class, DB glossy finished with epoxy polyster based powder coated paint through seven tank process fixed flush to wall, connecting with cable, complete all as specified and directed. (Note:- DB, MCBs/MCCB/Isolator shall be provided of same make)

M&L for Distribution board SPN 4 way, double door for mounting MCBs/Isolator, ELCBs etc factory made conforming to IS:13032 fabricated with CRCA sheet dust and vermin proof not less than 1.2mm thick fitted with DIN channel, neutral link and 200 Amps rated copper bus bars, IP-42 protection class, DB glossy finished with epoxy polyster based powder coated paint through seven tank process fixed flush to wall, connecting with cable, complete all as specified and directed. (Note:- DB, MCBs/MCCB/Isolator shall be provided of same make)

Supply and fixing Vertical loadline type TPN DB 4 way, as per IS-8623, IP-43 protection, universal mounting with suitable capacity copper bus bar with nuetral bus bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for MCCB TPN 63-100 Amps as incomer and MCB TPN/TP 32 to 63 Amps as outgoing and outgoing cables with copper lugs, crimpped with crimping tool complete all as specified and directed.

S&F MCB, single pole & neutral, 240 volts, 32 Amps current rating, breaking capacity 10 KA complete all as specifed and directed.

S&F MCB, single pole & neutral, 240 volts, 40 Amps current rating, breaking capacity 10 KA complete all as specifed and directed.

S&F MCB triple pole & neutral, 415 volts, 40 Amps current rating, breaking capacity 10 KA complete all as specifed and directed.

S&F MCB triple pole & neutral, 415 volts, 63 Amps current rating, breaking capacity 10 KA complete all as specifed and directed.

S&F MCB 10 Amps, single pole, 240 volts, breaking capacity 10 KA with 'B' characteristic complete all as specified and directed.

S&F MCB 20 Amps, single pole, 240 volts, breaking capacity 10 KA with 'B' characteristic complete all as specified and directed.

S&F MCCB four pole, 415 volts, fixed type, 100 Amps breaking capacity 25 KA complete all as specified and directed.

Sub main wiring with 2 single core 6 sqmm, PVC insulated PVC unsheathed stranded copper conductor cable in and including PVC concealed/surface conduit, 25 mm or higher dia. ISI marked, medium grade complete with all conduit accessories/ fittings including extension earth wire with 6 Sqmm single core PVC insulated, unsheathed copper cable fixed along with sub main in PVC conduit and connecting to earth dolly with all fixing material complete all as specified and directed. Note :- Three run of 6 sqmm copper cable shall be measured as one unit.

Sub main wiring with 2 single core 6 sqmm, PVC insulated PVC unsheathed stranded copper conductor cable in and including PVC concealed/surface conduit, 25 mm or higher dia. ISI marked, medium grade complete with all conduit accessories/ fittings including extension earth wire with 4 Sqmm single core PVC insulated, unsheathed copper cable fixed along with sub main in PVC conduit and connecting to earth dolly with all fixing material complete all as specified and directed. Note :- Two run of 6 sqmm copper cable and one run of 4 sqmm copper cable shall be measured as one unit.

S&F LED linear mirror light asthetically designed, provided with high output PMMA diffuser for glare free light 10 watt, dimension 600 mm including lamp and all accessories, connection with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make-Havells Cat Part No.ENDURALINEARNEOBS10WLED865SPCWH/ Make-Wipro Cat Part No. MAGMA LED 10 Watt/Crompton Cat Part No.LLL-10-CDL

S&F LED surface and wall mounted fitting LED batten (tube light fitting including LED), extruded aluminium housing provided for dissipation with polycorbonate diffuser and integrated electronic driver with industrial grade heavy duty having THD<10% suitable for 20 watt high lumen output PF>0.98, neutral white 20 watt 4 ft long light fitting with lamp etc complete with all light accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make-Havells Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH & CRYSTAL 1213TBDSTL20WLED865SGLASS/C&S Cat Part No.TATRA-Ei/20W/Crompton Cat Part No.LCTL-18CDL+LLT8-20

Supply, fixing, connecting and testing building security light fitting LED 45 watt with pressure die cast aluminium housing heat resistant toughened glass, IP-66 protection and impact resistance of IK07 with 10 KV buit in surge protection device, better optics for uniform distribution complete with electronic driver etc, including connecting up with three core copper conductor cable with 1.5 Sqmm size copper wire from ceiling rose to connector of light fitting complete all as specified and directed. Make-Havells Cat No.ENDURAPEARLNEOSL45WLED757PASYTOPC/C&S Cat Part No.LTESSI45WLED/LS/Crompton Cat Part No.LSTP-45CDL

M&L for fabrication of GI pipe, light grade, bracket of size 40 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer, complete all as specified and directed.

S&F Exhaust fan 300 mm sweep, energy saving 3 star, 230 volts, single phase, metalic body with louver shutter, bracket etc complete, including cutting the round hole of required size in wall finishing the same supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 23/0.0076 copper cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed. Make-Havells Model-Turbo force SP/Bajaj Model- 70046(MAXX AIR)/Crompton Model-TRANS AIR

S&F blanking plate complete all as specified and directed.

S&F LED bulb 9/10 watt suitable for lamp holder blanking plate complete all as specified and directed.

M&L for earthing complete with galvanized mild steel earth plate (electrode)600 x600x6.00 mm thik burried directly in ground earth pit not less than 2.25 mtr deep below ground level surrounded with adequate quantity of charcole dust mixed with salt ot a packed thickness of 15 cm all round the plate, using 4 mm dia GI wire as earth wire moulded and riveted to earth plate at one end and connected to main switch/control switch of the building at another end, GI earth wire incased in and including 15 mm dia GI "light grade' pipe from upper end of earth plate upto main switch/control of the building including 20 mm dia gi pipe light grade as water pipe from earth chamber to upper edge of earth plate, CI funnel with wire mesh fixed on water pipe and provision of PCC chamber and RCC pit cover with lifting handle, excavation earthwork including laying of GI pipe concealed in floor/ walls all as described in electrical plate No 5 of SSR Part-I complete all as specified and directed. Note:- The unit quoted rate deemed to be included for protection pipe and GI earth wire 4 mm dia from top of earth plate to 7.5 mtr above ground level.

Total amount of Sch 'A' Sec - IV (SITE CLEARANCE AND EARTHWORK) (For details see Schedule 'A' Part-IV in PDF folder)

Total amount of SCHEDULE 'A' PART-V (RETAINING WALL/PROTECTIVE WORK) (For details see Schedule 'A' Part-V in PDF folder)

Total amount of SCHEDULE 'A' PART-VI (ROAD, PATH, CULVERT & HARD-STANDING) (For details see Schedule 'A' Part-VI in PDF folder)

Total amount of SCHEDULE 'A' PART-VII (SEWAGE DISPOSAL) (For details see Schedule 'A' Part-VII in PDF folder)

Total amount of SCHEDULE 'A' PART-VIII (AREA DRAINAGE) (For details see Schedule 'A' Part-VIII in PDF folder)

Total amount of SCHEDULE 'A' PART-IX (HOT WATER SUPPLY) (For details see Schedule 'A' Part-IX in PDF folder)

Total amount of SCHEDULE 'A' PART-X(A) (EXTERNAL ELECTRIFICATION) (For details see Schedule 'A' Part-XA in PDF folder)

SCHEDULE 'A' PART-X(B) (EXTERNAL ELECTRIFICATION)

(b) ACCESSORIES :- (i) Aluminium Bus bar 300 Amp capacity for phases- 03 Nos and 250 Amp for neutral - 01 No. (ii) Digital multi function panel mounted meter for energy metering, monitoring and management system suitable for LT 3 phase 4 wire applications, using micro controllersand non voltage memory and providing anti tamper features and communication facility at high accuracy with accuracy for active energy as per IS:13779-99/IEC 61036, CL 1.0, operating temperature - 10 to +55 degree C, relative humidity 95% non condensing, 96x96x86 mm or nearer size, 3 line backlit display of 6 digit each to display voltage , current active power, reactive power, apparent power, power factor frequency and other parameters, digit height 8x4.8 mm, protection index IP-54 with all necessary CTs & PTs and instrument fuses, wiring complete - 01 Set (iii) Panel indicator lamp for three phase R, Y & B for each incoming and outgoing feeder - 01 Set (iv) Complete control panel internal wiring including making connection all incoming and out going MCB/MCCBs with suitable size of stranded copper conductor 2.5 Sqmm -01 job

(c) OUTGOING:- (i) MCB DP, rupturing capacity 10 KA, 32 Amp - 04 Nos (ii) MCCB 63 Amp 4 pole, 415 Volts,50 Hz, breaking capacity 16 KA(Ics=100% Icu) - 02 Nos (iii) Timer switches 250V single phase of 20 Amp rating with Contactor & Relay

Material and labour for earthing wth galvanised cast earth plateof size 600x600x6mm thick burried vertically in ground to a depth not less than 2.25mtr below GL with top edge of earth plate not less than 1.5mtr below GL the earth plate surrounded by adequate quantity of charcoal dust and salt all around earth plate 15 cm and earth plate connected with GI strip 32X6 mm as earth continuity lead with nut, bolts or rivetted to earth plate one end, protection with GI pipe light grade 40 mm bore, GI pipe medium grade 15 mm bore watering pipe from earth chamber to earth plate, CI funnel with wiremesh fixed on water pipe and PCC 1:2:4 type B-1 using 20mm graded stone aggregate in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1 duly reinforced with MS bar 6mm dia @150cc both ways with 10mm dia MS bar in lifting handle, including necessary excavation & earthwork etc all as shown in electirical plate No 3 of SSR Part-I and complete all as specified and directed. (Note:-On testing after completion if desired earth resistance does not obtain, the earthing shall be redone by contractor without any extra cost to Govt).

Supply, laying and jointing LT XLPE Insulated, galvanized steel strip or wire armoured power electric cable (heavy duty) 1100 volt grade with aluminium stranded conductor of size 70 Sqmm x 3.5 core confirming to IS 7098 (Part-I) of 1988 passing through pipes, in duct, on poles, in trenches, under road etc complete all as specified and directed.

Supply, laying and jointing LT XLPE Insulated, galvanized steel strip or wire armoured power electric cable (heavy duty) 1100 volt grade with aluminium stranded conductor of size 25 Sqmm x 3.5 core confirming to IS 7098 (Part-I) of 1988 passing through pipes, in duct, on poles, in trenches, under road etc complete all as specified and directed.

S&F cable route indicator made out of mild steel size 100 mm dia, 4mm thickness sheet welded with angle iron 40x40x6 mm for stand and two coat of synthetic enameled paint over a coat of red oxide primer and writing HT/LT cable route mark for suitable letter size, including embedded in PCC block of size 200x200x150mm in 1:3:6 type C1 using 20mm graded stone aggregate, complete all as specified and directed.

S&F earth continuity conductor or main earthing lead 32X6mm strip galvnised iron fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to pole or any other indicate situation for loop earthing etc as required complete all as specified and directed.

Total amount of SCHEDULE 'A' PART-XI (EXTERNAL WATER SUPPLY) (For details see Schedule 'A' Part-XI in PDF folder)

Total amount of Sch 'A' Part - XII (DEMOLITION/DISMANTLING) (For details see Schedule 'A' Part-XII PDF folder)

Note: Tenderers may be noted that amount of credit Rs. 325325.00 will be deducted from the total amount arrived, at the time of acceptance of contract. (For details please refer Schedule of credit).

M/s DS Enterprises

Prem singh kuwarbi and co

Epicon Constructions Private Limited

PIONEER REFRIGERATION AND ELECTRICALS

DEVKI NANDAN ASSOCIATES

OM TRADERS