RequiredExperience with Government
RequiredAnnual Turnover
RequiredCertificate (Requested in ATC)
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled No Track Suits - Sports ( 600 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition Polyester Blended with Polyester Blended with 1/8 ) Cotton Cotton Percentage of Blending ( in case of Blended Fabric ) Polyester 65 % and Cotton 35 % Polyester 65 % and Cotton 35 % Mass ( gram per square mtrs ) 240 240.0 Fabric Construction Woven Woven Weave ( In case of Woven Fabric ) Box Weave Box Weave Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Interlock Knitted Interlock Knitted Ends per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric Yes Yes Upper Lining Yes Yes Lower Lining Yes Yes Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) 65 * Netting mesh No of holes on base & bias within 625 Square millimeter 155 * Technical Requirements of Slide Fastener for Upper Closing Medium special duty Open End as per IS 14181 Latest Medium special duty Open End as per IS 14181 Latest Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) Medium special duty Open End as per IS 14181 Latest Medium special duty Open End as per IS 14181 Latest Slide Fastners are BIS Marked Not Applicable Not Applicable Width of Tape Elastic at Waist of Trouser 4.0 cm * 2/8 Width of Tape Elastic at Bottom of Upper 4.0 cm * Technical Requirements of Waist Band Waist band as per IS 9686- 1980 latest Waist band as per IS 9686- 1980 latest Waist Draw Cord Polypropylene Cord of 6mm dia * Draw Cord Ends Bell Caps * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping Yes Yes Lower provided with Piping Yes Yes Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 110 110 Embroidery Thread Not Applicable Not Applicable SIZE Size Medium (M) Medium (M) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 52.5 cm ( Medium ) * Width Across Bottom Opening (relaxed) 46 cm ( Medium ) * Length at front from top of collar to bottom 66 cm ( Medium ) * Sleeve length (from center of back to bottom of sleeve 84.5 cm ( Medium ) * Sleeve opening relaxed ( Cuff ) Width 11.2 * Front Neck Drop 9.5 * Back Neck Drop 1.7 * Length of Slide Fastener 64 cm( Medium ) * DIMENSIONS OF LOWER Side Seam Length 104.5 cm ( Medium ) * Waist relaxed ( Width Across ) 43 cm ( Medium ) * 3/8 Waist stretched (Width Across ) 52.5 cm ( Medium ) * Seat/Hip ( 15 cm below waist band) 52.5 cm ( Medium ) * Thigh (at Crotch) ( Width Across ) 36 cm ( Medium ) * Bottom Opening ( Width Across ) 21 * Front rise including waist band 28 cm ( Medium ) * Back rise including waist band 38 cm ( Medium ) * Length of Waist Tying Cord 155 * Bottom Fold (Hem) with full turn in(cm) 2.0 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 17 cm X 18 cm * Size of Inside Pocket at Chest- Upper 11 cm X 15 cm * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper Not Applicable Not Applicable Number of Pockets (Lower) 2 Side Pockets and 1 Back Pocket 2 Side Pockets and 1 Back Pocket Size of Side Pockets - Lower ( Length X Width ) ( cm ) 17 cm X 18 cm * Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower Side Pockets with Slide Fastener Side Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement With Canvas Reinforcement * SLEEVE Sleeve Type Reglan Sleeve * PIPING Position and - * 4/8 Dimensions of Piping on Upper Position and Dimensions of Piping on Lower - * STITCHING Sewing Thread 125 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in two rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in two rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in two rows with chain stitch on the elastic * Lining seams Inverted * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Multicolour Contrasting Pannels Any other colour as per buyer's requirements * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * 5/8 Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Any other colour as per buyer's requirements Any other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to perspiration ( IS 971 )- Mesh Lining 4 * Colour of Piping Material Any other colour as per buyer's requirements * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 1 1 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Printed Number of Logos on Upper 1 1 Number of Logos on Lower Not Applicable Not Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the No Yes
RequiredNo 6/8 specification Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Not applicable * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
