CONSTRUCTION OF MULTIPURPOSE HALL AT RUDRAPUR, U.S.NAGAR

Amount

DSR Item- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil.

DSR Item- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR Item- 2.35.3.1 Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor,apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of building shall be measurd for payment.)

DSR Item- 2.27 Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete.

SOR Item- 3-4 Construction of embankment with approved material obtained from borrow pits cu.m (including cost of compensation for earth taken from private land) with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause

DSR Item- 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DSR Item- 4.1 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

DSR Item- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

DSR Item- 5.37.1 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete,improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works upto plinth level

DSR Item- 5.37.2 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete,improve workability without impairing strength and durability as per direction of the Engineer-in-charge.All works above plinth level upto floor V level

DSR Item- 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

DSR Item- 5.9 Centring and shuttering including strutting,ropping etc. and removal of form for

DSR Item- 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

DSR Item- 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts.

DSR Item- 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

DSR Item- 5.9.3 Suspended floors, roofs, landings, balconies and access platform.

DSR Item- 5.3 Add or deduct for plaster drip course/ groove in plastered surface metre or moulding to R.C.C . projections.

DSR Item- 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item- 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand

DSR Item- 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

DSR Item- 9.21.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

DSR Item- 9.100.1 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

DSR Item- 9.96.1 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

DSR Item- 9.96.1 300x16 mm

DSR Item- 9.96.2 250x16 mm

DSR Item- 9.97 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete

DSR Item- 9.97.2 250x10 mm

DSR Item- 9.97.4 150X10 MM

DSR Item- 9.101.1 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

DSR Item- 9.51.2 Providing and fixing fly proof galvanised M.S wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

DSR Item- 10.14.1 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile 'B' (Single Pattam) Fixing with adjustable lugs with split end tail to each jamb

DSR Item- 10.11.1 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR Item- 10.25.2 Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

DSR Item- 10.25.1 Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete

DSR Item- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube

DSR Item- 10.30.2 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes

DSR Item- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

DSR Item- 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm

NSI Item- Providing and installing 20mm maple wooden flooring providing & laying Accredited American Hard Maple of 20mmx57/83mm widthxrandom Length 300mm onwards tongue & grooved for concealed fastening with cleats at every uncture with the pine runner (moistuure contents<14) of 68x38x900/1200mm cushion pad fixed at every joint of the runner & at 330 centre to centre. the full build up will be of 94/95 wich will laid on 6 mil thick plastic sheet (HDPE)as moisture barrier.(make Action, Robbins, Connors)

DSR Item- 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness sq.m to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

DSR Item- 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to sq.m IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per including pointing in white cement mixed with pigment of matching shade complete.

DSR Item- 13.1.2 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

DSR Item- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

DSR Item- 13.9.2 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

DSR Item- 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

DSR Item- 13.41.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

DSR Item- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

DSR Item- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR Item- 12.54.2 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier uspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

DSR Item- 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

DSR Item- 21.12.3 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

DSR Item- 5.26 Providing and filling in position, blown bitumen in expansion joints.

DSR Item- 5.28 Providing and fixing in position 12mm thick bitumen impregnated fiber per cm board conforming to IS: 1838, including cost of primer, sealing compound depth per Grade-A in expansion joints

DSR Item- 5.29.1 Providing and fixing sheet covering over expansion joints with iron screws as per design.

DSR Item- 21.1.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

DSR Item- 21.3.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

DSR Item- 7.40.1 Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Red sand stone - 30mm thick gang saw cut stone

DSR Item- 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

DSR Item- 22.14.1 Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

DSR Item- 12.55 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

DSR Item- 10.2 Structrural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting fixing in position and applying a priming coat of approved steel primer all complete.

DSR Item- 10.1 Structural steel works in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete for purlins work

DSR Item- 12.4.1 Providing ridges or hips of width 60 cm over all width plain G.S sheet fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia. G.I limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275gm/sqm.

DSR Item- 12.50.1 Supply & installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

DSR Item- 12.51.2 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : Ridges plain (500 - 600mm).

DSR Item- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR Item- 5.1.2 Providing and laying in position specified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR Item- 5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR Item- 6.4.2 Brick work with F.P.S. bricks of class designation 75 in superstructure Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item- 13.1.1 12 mm thick cement plaster in 1:4 ( 1 cement and 4 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

DSR Item- 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

DSR Item- 18.32.1 Constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1cement :4 coarse sand ) with C.c 1:2:4 floor over C.C 1:5:10 Finished with a floating coat of neat cement complete .Rectangular shape 600x450mm internal dimensions

DSR Item- 9.5 Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

DSR Item- 19.2 Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg

DSR Item- 16.3.2 Supplying and stacking at site. Over burnt (Jhama) brick aggregate 90 mm to 45 mm

DSR Item- 19.6.3 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

DSR Item- 7754 Gravel 5 mm to 10 mm

DSR Item- 7756 Gravel 3 mm to 6 mm

DSR Item- 7772 PEA Gravel

DSR Item- 18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

DSR Item- 18.10.1 15 mm dia nominal bore

DSR Item- 18.10.2 20 mm dia nominal bore

DSR Item- 18.12.3 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work. 25 mm dia nominal bore

DSR Item- 18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

DSR Item- 18.46.1 15 mm nominal bore

DSR Item- 18.46.2 20 mm nominal bore

DSR Item- 18.46.3 25 mm nominal bore

DSR Item- 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bor

DSR Item- 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approvedquality . 15 mm nominal bore

DSR Item- 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore

DSR Item- 18.19.1.1 Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore (Horizontal)

DSR Item- 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

NSI Item- Providing and fixing Bras Shower with complete all fitting and fixing in best quality

DSR Item- 18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

DSR Item- 18.51.1 Providing and fixing C.P. brass long body bib cock of approve quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

DSR Item- 17.1.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

DSR Item- 17.5.1 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

DSR Item- 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

DSR Item- 17.35 Providing and fixing soil , waste and vent pipes: S.C.I S&S pipe as per IS:1729

DSR Item- 17.35.1 100 mm dia

DSR Item- 17.35.2 75 mm dia

DSR Item- 17.37 Providind and fixing M.S.holder bat clamps of approved design to sand cast iron/cast iron (squn) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1cement :2coarse sand :4graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc:

DSR Item- 17.37.1 for 100 mm dia pipe

DSR Item- 17.37.2 for 75 mm dia pipe

DSR Item- 17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Sand cast iron S&S as per IS - 1729

DSR Item- 17.38.1 100 mm dia

DSR Item- 17.38.2 75 mm dia

DSR Item- 17.39 Providing and fixing plain bend of required degree. Sand cast iron S&S as per IS - 1729

DSR Item- 17.39.1 100 mm dia

DSR Item- 17.39.2 75 mm dia

DSR Item- 17.60.1 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

DSR Item- 17.56.1.1 Providing and fixing terminal guard 100 mm Sand cast iron S&S as per IS - 1729

DSR Item- 17.57 Providing and fixing collar : Sand cast iron S&S as per IS - 1729

DSR Item- 17.57.1.1 100mm

DSR Item- 17.57.2.1 75 mm

DSR Item- 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

DSR Item- 2.10.1.1 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

DSR Item- 19.1.2 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter

DSR Item- 19.3.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe

DSR Item- 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type.With common burnt clay F.P.S. (non modular) bricks of class designation 7.

DSR Item- 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR Item- 19.8.1.1 Extra depth for manholes. Size 90x80 cm. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR Item- 5.9.1 Centering and shuttering including strutting, propping etc. and removal of form for :

DSR Item- 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

DSR Item- 11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

DSR Item- 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

SOR Item- 3-3 Construction of Embankment with Material Obtained from Roadway Cutting Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

DSR Item- 2.1(h) Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

DSR Item- 2.11(h) Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure(the good earth shall be paid for separately)

DSR Item- 2.3(h) Supplying and stacking sludge at site including royalty and carriage up to 1 km(sludge measured in stacks will be reduced by 8% for payment)

DSR Item- 2.4.3(h) Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) screened through sieve of I.S. designation 4.75 mm

DSR Item- 2.26(h) Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level. The vertical members shall consist of four nos angle iron of size 25x25x3 mm, 1.8 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical mambers shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect.

SOR Item- 4-7-1B WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 404. By Mechanical Means

SOR Item- 4-7-2B WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. By Mechanical Means

SOR Item- 2-2 Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion cu.m 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work.(Based on PWD specifications)

SOR Item- 2-3 Cement Concrete Pavment:- Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30 (Cement@404 kg/cum), coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications.

NSI Item- Providing Trimix flooring including all labour, T&P Reqired for proper completeioin of the work

SOR Item- 11-4-3-1 Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

SOR Item- 11-1-1-1 Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Upto 3 m depth

SOR Item- 2-2 Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203

SOR Item- 12-1-2 Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Claus es 602, 603, 604, 1202 & 1204 In 1:4 Cement mortar

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

NSI Item- Acoustic Treatment Underdeck Ceiling: Providing and fixing of 12mm thick Acoustic Treatment (Ceiling Insulation) on existing Frame will be fixed and Chicken Wire Mesh or GI Wires as per site requirement. As per directions of site engineer incharge.

NSI Item- Acoustic Treatment on Walls: Providing & Fixing of approved color on 19mm Thick acoustic board of approved NRC of 0.92 NRC with a density of 400 KG/m3 with the spread frame at termination /10 Min with a FR report on basis of Class -1 & Also the spread frame at 1.5 min should be nil as per FR Test Reports. The Acoustic Board will be fixed to the Frame of 45mm x 45mm x 0.4mm with Stud at 600mm x 600mm Center to Center or as per site requirement. The Center to be filled with 50mm Thick Polyester Fiber Insulation With Anti-Vibration Pads (Wherever Require).

NSI Item- Supply installation testing and commissioning of single skin FDV unit with non thremal break profile 24 G GI outside sheet with precoating and with flowing section.Complete with fan section with DIDW forward curved centrifugal fan,drive motors and accessories.frame work shall be of Anodized Aluminum construction with Non thermal break profile.Pre filter section with 98% Efficiency filter rating. Floor Mounted Units 20000 CFM @ 55 MM WC

NSI Item- Complete with celdek section- 150 mm thick Cellulose based Evaporative Pad,, water recirculation monobloc pump, with necessary piping, valves, SS-304 water tank, water distribution piping, nozzles suitable for FDV unit.

NSI Item- CONSTRUCTION FEATURES OF MOTORISED BLOWER, FANS OR EXHAUSTER. A) CASING . B) Casing made from mild steel plates and sheets reinforced with angle Iron.Its design is involute scroll for giving maximum efficiency . Suction is done with round flanged with supported fins to the cover and outlet is generally rectangular with extra support of angle on the casing . Minimum thickness of sheet is used in the casing 2.5 mm with maximum thickness goes to 3 mm MS sheet. The fourth quarter of casing is much larger as compaired to the other fans to get the maximum efficiency and free flow of air to be dragged from the outlet . C) Impeller is of enclosed design made from mild steel sheets . It is designed for giving maximum efficiency for the designed head and volume . Impeller curve is of BACKWARD/FORWORD CURVED and the blade angle is of 56 degree to 48 degree . The Hub which is connected the impeller to the motor shaft is of Ms casting and the designed of the hub is beak type to get the maximum air flow at the center of the impeller . D) MOTOR PEDESTAL is of mild steel reinforced with heavy angles . Its box section is welded to the casing so that all the center of mass will on the same base . IMPELLER is 100% dynamically as well as statically balanced thru ABRO BALANCING MACHINE with upto 0.001 gms in polar coordinates weight . STANDARD blowers, fans and exhausters are very ruggedly built , so that they withstand rough handling and can be used in duty atmospheres. Each blower , fans or exhauster is properly tested in our works Prior to dispatch . Exhaust air unit 18000 cfm/ 1400 rpm

NSI Item- SHEET METAL WORKS ( DUCTING , GRILLS DAMPERS ETC) Fabrication, supply, installation, testing & commissioning of Galvanised Iron ( GI ) GI Sheet ducting complete with nut bolt, gaskit, silicon sealent duct supports etc. as per drawings and specifications. .

NSI Item- 20 Gauge (Thickness 1.0mm)

NSI Item- 22 Gauge (Thickness 0.8mm)

NSI Item- 24 Gauge ( Thickness 0.63mm)

NSI Item- Supply, fixing and commissioning of Double deflection , powder coated extruded aluminum grilles complete with black anodized extruded aluminum VCD, nuts, bolts, screws etc. as per approved drawings and specifications. (1200 MM X 250 MM) Supply air grilles with Collar Box type damper.

NSI Item- Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

NSI Item- Supply, installation, testing and commissioning of Gravity louvers

NSI Item- Supply, installation, testing and commissioning of Flexible double Canvass Connections for FDV units

NSI Item- S.I.T.C. of Duct insulation with following type fixed with adhesive as per manufacturers specs or using 9 mm thick closed cell cross-linked polyethylene FR XPE ( External of Supply DUCT)

NSI Item- Supply of Acoustic lining of duct work with following type 15 mm thick open cell nitrile rubber Internal of DUCT)

NSI Item- Supply of electrical Starter suitable for following: Floor Mounted FDV unit

NSI Item- 20,000 CFM at 35 MM WC

NSI Item- 18,000 CFM /1400 rpm

DSR Item- 1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group C

DSR Item- 1.11 Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

DSR Item- 1.12 Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

DSR Item- 1.14 Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

DSR Item- 1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

DSR Item- 1.14.2 2x2.5 sq. mm + 1x2.5 sq.mm earth wire

DSR Item- 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

DSR Item- 1.14.10 4x10 sq. mm + 2x 6 sq.mm earth wire

DSR Item- 1.18.2 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

DSR Item- 1.21.2 Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required. 25mm

DSR Item- 1.22.1 Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.75 mm X 75 mm X 60 mm deep

DSR Item- 1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

DSR Item- 1.24.1 5/6 amps switch

DSR Item- 1.24.4 3 pin 5/6 amp socket outlet

DSR Item- 1.24.6 Telephone socket outlet

DSR Item- 1.25 Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

DSR Item- 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

DSR Item- 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

DSR Item- 1.33 Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

DSR Item- 1.34 Supplying and flxing brass batten/angle holder including connection etc. as required.

DSR Item- 1.41 Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

DSR Item- 1.45 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

DSR Item- 1.50 Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

DSR Item- 1.51 Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

DSR Item- 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

DSR Item- 2.4.3 8 way (4 + 24), Double door

DSR Item- 2.4.2 6 way (4 + 18), Double door

DSR Item- 2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

DSR Item- 2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.63 amps

DSR Item- 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

DSR Item- 5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

DSR Item- 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.( For D.G Set & CSS)

DSR Item- 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

DSR Item- 4.1 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

DSR Item- 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.1.3 225 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.1.5 375 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.1.6 450 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.1.7 600 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.1.16 900 mm width X 75 mm depth X 2.0 mm thickness

DSR Item- 4.2 Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

DSR Item- 4.2.1 100 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.2.2 150 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.2.3 225 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.2.4 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.2.5 375 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.2.6 450 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.2.7 600 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.2.16 900 mm width X 75 mm depth X 2.0 mm thickness

DSR Item- 4.3 Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

DSR Item- 4.3.1 100 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.3.2 150 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.3.3 225 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.3.4 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.3.5 375 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.3.6 450 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.3.7 600 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.3.16 900 mm width X 75 mm depth X 2.0 mm thickness

DSR Item- 4.4 Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

DSR Item- 4.4.1 100 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.4.2 150 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.4.3 225 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.4.4 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.4.5 375 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.4.6 450 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.4.7 600 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.4.16 900 mm width X 75 mm depth X 2.0 mm thickness

DSR Item- 4.5 Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

DSR Item- 4.5.1 100 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.5.2 150 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.5.3 225 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.5.4 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item- 4.5.5 375 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.5.6 450 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.5.7 600 mm width X 50 mm depth X 2.0 mm thickness

DSR Item- 4.5.16 900 mm width X 75 mm depth X 2.0 mm thickness

DSR Item- 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

DSR Item- 7.1.1 Upto 35 sq. mm

DSR Item- 7.1.2 Above 35 sq. mm and upto 95 sq. mm

DSR Item- 7.1.3 Above 95 sq. mm and upto 185 sq. mm

DSR Item- 9.4 Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

DSR Item- 9.4.17 3½ X 25 sq. mm

DSR Item- 9.4.18 3½ X 35 sq. mm

DSR Item- 9.4.19 3½ X 50 sq. mm

DSR Item- 9.4.20 3½ X 70 sq. mm

DSR Item- 9.4.21 3½ X 95 sq. mm

DSR Item- 9.4.27 3½ X 300 sq. mm

DSR Item- 14.13 Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc. as required

DSR Item- 14.13.2 80 mm dia

DSR Item- 14.13.3 100 mm dia

DSR Item- 15.30 Supplying,installation,testing andcommissioning of Microwave technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10 A, for mounting height up to 2.6 meter and for 5m X 20m coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

DSR Item- 3.3 Supplying, installing, testing and commissioning of following capacity TPN distribution tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, interconnections, earthing etc. as required.

DSR Item- 3.3.3 16 A, TPN, 6 way

DSR Item- 3.3.6 32 A, TPN, 4 way

DSR Item- 3.3.10 63 A, TPN, 4 way

DSR Item- 14.7 Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.(For CSS, D.G Set)

DSR Item- 14.12 Providing 15 mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels.

NSI Item- Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-Captiva 50 (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge. 1200 mm sweep

NSI Item- Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS (Make : Finolex) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. 300 mm sweep 900 rpm

NSI Item- Supply of heavy duty wall mounted fan - 400 mm dia Model - (Finspeed Wall) complete in all aspects etc. as per direction of Engineer in Charge. (Make : Havells)

NSI Item- SUPPLY OF LED Glass Bulb B22, 12 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

NSI Item- Supply and fixing of T5 LEDTube Light -Wall mounted LED batten , extruded aluminium Heat sink provided for efficient heat dissipation & integrated electronic driver. (1X22W LED )complete in all aspects as per direction of Engineer in Charge

NSI Item- Supply & fixing of Ceiling concealed Light Recess mounting luminiare suitable for Armstrong / Grid/ Ceiling Concealed Light 12W LED Concealed Round shaped Panel Light with adopter of standard make (Havell's / Bajaj) complete in all aspects like Ballast , housing connecting wire etc. as per direction of Engineer in Charge.

NSI Item- Supply & fixing of Ceiling Light - RC380B LED34S-6500 G3 PSU OD Recess mounting luminiare suitable for Armstrong / Grid/ Ceiling (600X600mm) with electronic driver & high Brightness SMD LED's. Lamp Type 32 Watt LED 4000 ,6500 K . High efficiency diffuser IP 20 of standard make (Philips) complete in all aspects like Ballast , housing connecting wire etc. as per direction of Engineer in Charge

NSI Item- Supply & fixing of LED Mirror Light -Providing & Installation of Factory packed ready to installed LED mirror light with LED Lamp not less than 4 Watt diffused optics complete in all aspects including base plate (for recess in wall ) connecting wire etc.of as per direction of Engineer in Charge. .

NSI Item- Supply & fixing of main panel with 1 no. incomer of 400 amp.TPN MCCB (25 KA)& outgoings of 03 no. 100 amp. FP MCB (25 KA) & 04 no. outgong of 63 amp. FP MCB with suitable busbar, change over switch,ammeter, voltmeter,indicating lamps etc. complete in all respect.

NSI Item- Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.

NSI Item- 3.5c x 185 sq. mm cable

NSI Item- 4c x 95 sq. mm cable

NSI Item- 3.5 c x 70 sq.mm cable

NSI Item- 3.5 c x 35 sq.mm cable

NSI Item- 3.5 c x 25 sq.mm cable

NSI Item- 4c x 10 sq. mm cable

NSI Item- 4c x 6 sq. mm cable

NSI Item- Supply &Installation of Decorative pole 3.5 Mtr. Long( DLP-2-35-201) having following diamension, approved by Engineer in charge with making connection complete in all respect.

NSI Item- Supply & fixing of LED Street light luminaire(1x70W) BRP 409 LED 065 CW HE MR FG S1 PSU GR IP66 , Lumen Output-3500-7000, 5700 k LM6 high pressure die cast aluminium , cover Polycarbonate/ Glass, 140V-270 V AC 50Hz in including Housing , Ballast , Lamps, Connecting Wire etc. of standard make (Philips) complete in all aspects as per direction of Engineer in Charge.

NSI Item- Supply of 250 kVA F. G. cummins Silent DG Set comprising of Engine coupled with Three Phase Alternator mounted on a common base frame along with other accessories; Manual Control Panel, Fuel Tank, Leads; 415V, 3000 RPM complete in all aspects as per direction of Engineer In-charge

NSI Item- Supply and installation of 10 KVA 180 V Solar Inverter with Solar Priority- 4 hours backup- Fully Automatic with 10200 watt pannel including 10 kVA Sine wave invt with digital display 180 V with Tubular Batteries , 10200 Watt Solar Pannel in poly crystalline silicon, solar charge controller complete in all aspects as per directions of engineer- in-charge

NSI Item- SITC of compact substation having 320 KVA, 11KV/433V, copper wound, oil cooled outdoor type transformer with off load tap changing facility which is to be as per the specification and the data sheet provided incoming HT RMU with SF6 circuit breaker of 630A capacity outgoing moulded case circuit breaker of 400A 36KA 4P MCCB manual fixed type with overcurrent short circuit releases. The rate included the cost of frame work for the compact substation to the internal arc tested as per standard norms.

NSI Item- Supply and installation of Mounting Arrangements for Sports Lighting with nuts, bolts and washers as per instructions of Engineer-in-charge.

NSI Item- Supply and laying of cabling of approved brand. 1. 2.5 sqmm 3 core for hall lighting 2. 6 sqmm, 4 core for Main Panel feeder cable as per instructions of Engineer-in- charge,

NSI Item- Supply, Installation, testing and commissioning of Control Panel. Control Panel Specifications as follows: 1. MCCB 160 A, TP, with Thermal Magnetic Release (Brand L&T) 2. Indicating Light 220 Vac RED, (Main R- Phase) 3. Indicating Light 220 Vac Yellow, (Main Y-Phase) 4. Indicating Light 220 Vac Blue, (Main B- Phase) 5. Digital VAF Meter size 96 × 96 6. CT 200/5, 5 VA, CL-1

NSI Item- Earthing of Panel as per instructions of Engineer-in-charge

NSI Item- Supply and fixing Sports Light which achive more than 2000 Lux Level as per design which must be vetted by IIT or equivalent institute including all fixtures, testing, commissioning etc. complete in all respect.(Sports lighting must be designed which achieve Lux Level for National Games HD Telecasting norms.) (No. of Light may be variable) make Osram, Philips, Ventura-USL