REPAIR TO TOILETS, BATHROOMS, SUNKEN TREATMENT AND SANITARY FITTINGS IN ZONE-A AT DEFENCE LAB JODHPUR

Amount

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type including cement mortar bedding ( but not backing ) complete all as specified & directed by Engineer-in-charge.

Demolition of un reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified & directed by Engineer-in-charge.

Glazed ceramic coloured (colour & shade as approved) tile 450x300x7 mm thick on vertical surface such as skirting / dado set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified & directed by Engineer-in-charge.

Glazed ceramic coloured (colour & shade as approved) tiles non skid of size 300x300x7mm thick as in flooring set and jointed in neat cement slurry over & including 20 mm thick screed in cement mortar (1:6) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified & directed by Engineer-in-charge.

M&L for Water proofing treatment to RCC sunken slab as specified below and as directed by Engineer-in-Charge. :- (a) 15 mm plaster in CM 1:3 with WPC on raised vertical surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust partucles, dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hr (g) Laying concrete 1:4:8 over the coating as per requirment (h) Refixing the sanitary pipes with the waterproofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and sanitary pipe with non shrink cementitious grout (k) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Make:- Dr. Fixit/Fosroc/STP Note:(i) The treatment shall be carried out as per the manufacturers instructions and as directed by the Engineer in charge. (ii) The Plan area of floor shall be considered for payment. (iii) WPC shall be measured and paid separately.

Supply only water proofing compound complete all as specified & directed by Engineer-in-charge.

Taking down cement plaster on stone walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed by Engineer-in-charge.

Rendering 15mm thick in cement mortar (1:4) on any face of stone masonary walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

Rendering 10 mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and even without using extra cement complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise as directed complete all as specified & directed by Engineer-in-charge.

Taking down Shutter exc 1 sqm and not exc 2 sqm each complete all as specified & directed by Engineer-in-charge.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube complete all as specified & directed by Engineer-in-charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain / coloured PVC "C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified & directed by Engineer-in-charge.

S&F 150mm long aluminium anodised handle cast type and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair aluminium anodized barrel tower bolts of extruded section length of bolt 150mm complete all as specified & directed by Engineer-in-charge.

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified & directed by Engineer-in-charge.

Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified & directed by Engineer-in-charge.

S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified & directed by Engineer-in-charge.

S&F 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified & directed by Engineer-in-charge.

Fixing only 15mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified & directed by Engineer-in-charge.

Fixing only 20mm bore steel water tubing any grade with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified & directed by Engineer-in-charge.

Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flush pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified & directed by Engineer-in-charge.

Vitreous china wash down water closet pan ( pedestal pattern ), white/ coloured including seat & cover, flush pipe, connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified & directed by Engineer-in-charge.

PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified & directed by Engineer-in-charge.

Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified & directed by Engineer-in-charge.

Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified & directed by Engineer-in-charge.

S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair stop valves, fancy type, CP with long shank and cup (concealed type), screwed both ends for 15mm bore of iron pipe or for union and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair of Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & directed by Engineer-in-charge.

S&F Stainless kitchen steel sink with dranage board 1mm thick sheet of over all size 915x460mm with boul size 410x330x160mm including CP waste coupling and PVC waste pipe up to chamber fixed on and including cantilivers angle iron brackets of 2nos 25x25x3mm complete all as specified & directed by Engineer-in-charge.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified & directed by Engineer-in-charge.

Dismantling of 110/100/75mm bore PVC/cast iron or reinforced concrete drain pipes, jointed in cement mortar/lead joint and taking out of trenches if required /walls including fittings, complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC SWR type 'B' socketed rain water pipes 110mm dia conforming to IS: 4985/ IS: 13592 complete all as specified & directed by Engineer-in-charge.

Dismantling Cast Iron work of any Description and in any position complete all as specified & directed by Engineer-in-charge.

S&F 100 bore cast iron P or S trap complete all as specified & directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore (SWR) PVC bends any radius complete as specified and directed by Engineer-in-Charge.

S&F 75 mm bore (SWR) PVC bends any radius complete all as specified & directed by Engineer-in-charge.

S&F 75 mm bore (SWR) PVC plain floor trap complete all as specified & directed by Engineer-in-charge.

S&F 125/110 mm bore (SWR) PVC gully trap complete all as specified & directed by Engineer-in-charge.

S&F in repair CP brass jet for EWC complete all as specified & directed by Engineer-in-charge.

S&F in repair, stainless steel toilet paper with cutting edge cover (As per sample kept in AGE B/R-I office) complete all as specified & directed by Engineer-in-charge.

S&F in repair, stainless steel soap dish of standard size (As per sample kept in AGE B/R-I office) fixed with chromium plated screws complete all as specified & directed by Engineer-in-charge.

S&F, in repair, white/ black plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified & directed by Engineer-in-charge.

Preparation of newly plastered surfaces of walls etc., and applying two coats of oil emulsion including chalk whiting preparatory to distempering complete all as specified & directed by Engineer-in-charge.

Preparation of new plastered surfaces of ceiling & applying two coats of white wash complete all as specified & directed by Engineer-in-charge.

vinayandsons

HOODA CONSTRUCTION COMPANY

MAA AISHA TRADERS SIWANCHI GATE