SPL REPAIRS TO LT OH LINE INTO UG CABLE AT OL BARODA

Amount

Dismantling of cross arms/bracing supposts/clamps/back plates or any structural sections including removing nuts, bolts, washers etc complete.

Dismantling of old deterioted ACSR conductor, of any size, any type etc. complete.

Excavation in trenches nexc 1.5 mtr wide and nexc 1.5 mtr in depth for taking out cable / pipe line n.exc 10 sq mtr on plan and n.exc 1.5 mtr depth and getting out in soft/loose soil complete.

Returning filling in trenches excavated soil including spreading levelling watering and well ramming in layers n.exc 25 cm. Complete

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point complete.

M&L for sand cushioning to PVC cable with using clean dry and natural river sand gently punning below/around cable complete.

M&L well burnt bricks sub class 'B' as in protection of cable laid dry, flat abutting each other width wise complete

Supply, Laying, jointing and testing electric 120sqmm 3.5 core under ground LT cable PVC/XLPE insulated armoured aluminium conductor cable 1100 volts grade in trenches ducts, pipe on walls, poles of following sizes

All as per Item No : 08 above but for 95 Sqmm 3.5 core

All as per Item No : 08 above but for 50 sq mm 3.5 core

All as per Item No : 08 above but for 16 sq mm 4 core

All as per Item No : 08 above but for 25 sq mm 3.5 core

M&L for GI tubing light grade 80 mm dia bore fixed on wall / pole laid in trenches / under road complete.

M&L for GI tubing light grade 50 mm dia bore fixed on wall / pole laid in trenches / under road complete.

M&L in replacement earthing with galvanised steel earth plate electrode 60 cm X 60 cm X 6.0 mm burried directly in ground level with top edge of earth plate at a depth not less than 1.5 m below ground level connected to and including galvanised iron strip 32 X 6 mm as earthing lead by means of bolts, nuts, check nuts and washers etc made of GI and connected to earthing test point all as shown in electric plate No. 3 of SSR indicated and testing on completion including excavation and earth work in any type of soil/rock, PCC (1:3:6) type C-1 earthing chamber, cast iron cover with lifting handle, funnel with GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 40 mm bore light grade 7.5 m long test point etc complete.

S&F in replacement bracket with clamp for fixing street light fitting made out of GI pipe light grade including bending to shape of length 1.5 m and 40 mm dia fixed with suitable clamp of FI 25 x 6mm with bolt nut etc. Complete

M&L in replacement, erecting & fixing in true vertical position steel tubular swaged pole type 410S P-31 ( 9.0 metre long ) confirming to IS 2713 with cast iron base plate, finial taper plug, bolts, nuts and screws welded & reduced section & longitudinal weld through out entire length of pole including 2 coat of black bituminous paint upto GL level of pole & remaining exterior portion of the pole & two coat of aluminium paint over a coat of red oxide primer including excavation & earth work & PCC work as shown on TD drawings complete.

Taking down old defective Street Light and S&F 72 Watt LED Street Light fitting New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device including GI bend 40mm dia pipe of 1.2 mtr length with FI 25 x 6mm clamp to fitt the security Light fitting etc. complete.

M&L in replacement flat aluminium, twin core, PVC insulated, overall PVC sheathed solid aluminium conductor service cable of 2.5 sqmm sizes.

S&F in replacement PVC Jnction Box of Size 20 cm x20 cm x 15 cm with hinged door inculding locking arrangment with MCB SP 6 Amps 1 No including necessary clamp, Nuts, bolt etc complete.

S&F Cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material (Epoxy Based) and accessories suitable for 3 ½ core XLPE armoured AL conductor cable of size 25 to 50 Sqmm complete.

S&F Cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material (Epoxy Based) and accessories suitable for 3 ½ core XLPE armoured AL conductor cable of size 70 to 95 Sqmm complete.

S&F Cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material (Epoxy Based) and accessories suitable for 3 ½ core XLPE armoured Aluminium conductor cable of size 120 to 150 Sqmm complete.

M&L in replacement fabrication of bus bar chamber suitable for 415 volts 3 phase 4 wire system with MCCB 125A 16 KA 4 pole, outdoor type, double door, with pedestal mounted, weather and vermin proof fabricated out of 3.15 mm thick MS CRCA sheet with anti corrosive coating & finally epoxy polyster powder coating of flint grey shade including 3 nos. phase indicating lamps, insertion of suitable cable glands for all incoming and out going cable including grouting of panel board 60 cm above & 30 cm below ground level duly supported on 50x50x6mm angle iron frame & welding 1.2 mtr long angle iron legs of size 50 x 50 x 6mm on all the four corners embedded in PCC 1:2:4 using 20 mm stone aggregate upto 30 cm depth comprising of 4 nos. Aluminium bus bar 200 Amp for phases & 100 Amp for neutral mounted on DMC/ porcelain insulator support complete.

Supply, installing, testing and commissioning in replacement factory made and tested LT feeder pillar box (KIOSK) outdoor type CPRI approved platform mounted, suitable for 415 volts 3 phase 4 wire , 50 Hz AC supply system having copper bus bar installed on DMC/Epoxy insulators, dust and vermin proof, IP-65 class protection and made of 3.15mm CRCA MS sheet with front opening type with double door shutter and locking arrangement, powder coated finish (over a coat of red oxide), primer on outside and two coats of red oxide primer on inside surface & including platform with PCC 1:4:8 type D2 with 40mm crushed stone aggregate 20cm thick in foundation and of height 1.2 mtr above the nearest road level & the TPN copper bus bar of rating not less than the 1.5 times (260 Amps capacity) the rated capacity of the incomer MCCB with accessories are:-(i) Incoming MCCB 4P 250 Amp, 35 KA -01 No(ii) Outgoing MCCB 4P 100 Amp, 25 KA -04 Nos(iv) Digital voltmeter & Ammeter with necessary CTs(v) Internal wiring with PVC insulated, multi stranded copper conductor cable, 1100 V grade, IS 694 marked of approriate size but not less than 2.5 sqmm(vi) Phase indicating LED lamps (R-Y-B) -01 set (vii) Spare chamber for MCCBs - 01 Nos

Supply, installing, testing and commissioning factory made and tested LT feeder pillar box (KIOSK) outdoor type CPRI approved platform mounted, suitable for 415 volts 3 phase 4 wire , 50 Hz AC supply system all as specified and directed having copper bus bar installed on DMC/Epoxy insulators. The panel shall be dust and vermin proof, IP-65 class protection and made of 3.15mm CRCA MS sheet with front opening type with double door shutter and locking arrangement, powder coated finish (over a coat of red oxide), primer on outside and two coats of red oxide primer on inside surface. The panel is including platform with PCC 1:4:8 type D2 with 40mm crushed stone aggregate 20cm thick in foundation and of height 1.2 mtr above the nearest road level. The TPN copper bus bar of rating not less than the 1.5 times(260 Amps capacity) the rated capacity of the incomer MCCB with following accessories :- (i) Incoming MCCB 4P 200 Amp, 35 KA -01 No (ii) Outgoing MCCB 4P 63 Amps 36 Amp, 25 KA -04 Nos (iv) Digital voltmeter & Ammeter with necessary CTs(v) Internal wiring with PVC insulated, multi stranded copper conductor cable, 1100 V grade, IS 694 marked of approriate size but not less than 2.5 sqmm (vi) Phase indicating LED lamps (R-Y-B) -01 set (vii) Spare chamber for MCCBs - 01 Nos

Supply, installing, testing and commissioning in replacement factory made LT feeder pillar box (KIOSK) outdoor type platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system having bus bar installed on DMC/Epoxy insulators, dust and vermin proof, IP-65 class protection and made of 2.0 mm Stainless steel SS-316 grade sheet with double door shutter and locking arrangement, front and back opening, using stainless steel hinges, bolts and nuts & washer etc. including platform with PCC 1:4:8 type D-2 with 40mm crushed stone aggregate 20cm in thick in foundation and of height 0.9 mtr above the nearest road level & the TPN aluminium bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB (a) MCCB 4 pole 16 kA 63 Amps with tinned copper link 01 No (Incommer) (b) MCB 4 pole 10 kA 32 Amp - 03 Nos (c) Phase indicator lamps(R-Y-B) -01 set of three (d) Automatic street light switch of rating 8 KW in three phase using nature sensor for automatic switching "ON/OFF" of steel lighting based on lux level of natural light along with 40 Amps Four pole contactor, MCB 40 Amps four pole with support terminals prewired with PVC insulated 25 sqmm multi strand copper wire enclosed/housed in pole wall mounted enclosure made of rust proof, shock proof, termite proof & dust proof FR grade moulded compound Junction Box Circuit wiring - 02 Nos (Timers two Nos for each panel for different ciruits) complete

City Light

Shree Vaishno Enterprises

DARSHAN CONSTRUCTION Co.

Gayatri Associates