PROVN OF POL STORE INCLUDING SERVICES AT RAMGARH AND PROVN

Amount

NOTE: Schedule ‘A’ Part I to III are under Ser No. 3.00 to 5.00 are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Schedule 'A' Part I to IV for Ramgarh

Lump sum price worked out for BUILDING WORK as listed in Sch 'A' Part I

Lump sum price worked out for Hard Standing as listed in Sch 'A' Part II

Lump sum price worked out for INTERNAL ELECTRIFICATION as listed in Sch 'A' Part III

SCH 'A' Part IV (MISC E/M ITEMS)

M&L for stone patti 40 to 50mm thick rough dressed jodhpur stone slab cover in trenches for protection of cable 25 to 30 cm wide and not less then 50cm in length laid dry abutting each other with gap between adjecent slab not excedding 10 mm over sand cushoing all as specified and directed by EIC.

supply & fix following type/rating MCB’s including necessary connection as under:- (a) S & F MCB, 6 to 32 Amp, SP, 240 Volt Make : Legrand /Schneider/Siemens/C&S

(b) S&F MCB, 40 to 63 Amp, SPN, 240 Volt Make :Legrand /Schneider/Siemens/C&S

S&F in replacement flameproof Fluorescent tube light fitting flameproof type FLP-WP of T5 1x36 w including integral reflector made of alluminium alloy LM6,with electronic ballast,bipin holders,connector block, etc and all accessorie pre-wired and incuding connecting up with twin core twisted flexible copper conductor with suitable size all as specified and as directed by Engineer-in-charge.

Supply & fix 380 (15')mm single phase Flameproof exhaust fan including making holes in to the wall as per fan size and making good the disturved surfaces all as directed by Engineer-In-Charge

SCH 'A' PART- V (MISC ITEM B/R & E/M) : FOR TECH AREA JAISALMER

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/Loose soil

Removing excavated material n exc. 250m but not exc 500m and depositing where directed at a level n exc. 1.5 m above the starting point in soil

Rolling and consolidating formation surfaces in cutting by power roller exc 8T and n exc 12T

M&L for soling or subbase 150mm thick (spread thickness) with broken boulders or quarried stone, interstices filled, surface formed, rolled and consolidated to required gradient and camber.

M&L for 150mm thick (compacted thickness) WBM in two layers, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required.

Preparing WBM surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc and M&L for applying evenly a priming/tack coat with bituminious primer of grade VG 30 at 10kg/Xsqm.

M&L for premix bituminious macadam with 4% binder content (consolidated thickness 75mm or less) using bitumen of grade VG 30, laid/rolled and compacted to gradient and camber required.

M&L for premix bituminous asphaltic semi dense concrete 25mm consolidated thickness using bitumen of grade VG 30 and 5.5% binder content by weight of total mix, rolled and compacted to required gradient and camber.

M&L for continious brick edging with width equal to the length of the brick, laid dry on edge vertically.

M&L for preparation of new bituminious surfaces and applying two coat of water based road marking paint all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Hard/dense soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Hard/dense soil

Description all as per Sl item No 18 above but in soft/disinetgrated rocl

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in soil

M&L for filling under floors with available approved soil spread and levelled in layers n exc 15cm thick watered and well rammed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point in soil

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point in rock

M&L for PCC (1:4:8) type D-2 ( 40mm graded stone aggregate) as in foundations, filling and mass concrete.

M&L for cement concrete cast-in-situ 1:2:4 type B-1 (20mm graded stone aggregate) as in lintels upto 1.5m clear span including use and waste of formwork as required. Note:- Reinforcement measured and paid in respective items

M&L for precast cement concrete 1:3:6 type C-1 (20mm graded stone aggregate) solid block masonry exc 10cm in width and setting in CM 1:6 etc complete.

M&L for reinforced cement concrete 1:11/2:3 type A1 (20mm graded stone aggregate) nominal mix as in beams, cantilevers, lintels over 1.5m span etc complete.

M&L for reinforced cement concrete 1:11/2:3 type A1 (20mm graded stone aggregate) nominal mix as in slabs supported on walls, beams and columns in floors or roof, canopies, shelves and the like etc complete.

M&L for reinforced cement concrete 1:11/2:3 type A1 (20mm graded stone aggregate) nominal mix as in Chajjas and the like etc complete.

M&L for squared rubble walling, Jodhpur type brought upto vourses, well bonded, bedded and solidly hearted, built in CM (1:6).

Extra over square rubble walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints etc complete.

External angles (for quoins and jambs) in facing for walling of squared rubble uncoursed or brought upto courses.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc 200mm thick (Horizontal or sloping)

Use and waste of formwork to chajjas and similar items including edges.

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F aluminium anodised barrel tower bolts of extruded section and of size 200mm

S&F 300mm size aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast- aluminium alloy.

S&F 100mm size butt hinges, extruded anodised aluminium alloy with galvanised mild steel hinge pin, and fixed

S&F 150mm size extruded anodised aluminium alloy handles, fabricated type

S&F anodised aluminium tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F Mild steel of grade Fe-290 Gde E-165 as in framed work for window grills with ends of bars shouldered and/ or rivetted or forged into spikes, framed guard bars, barred iron doors and similar work

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and mild steel wire (annealed) not less than 0.9mm dia.

Ditto all as in Sl Item No 50 above but 5mm dia and over upto and including 10mm dia in stirrups, spacer and binders

S&F anodised aluminium frame for ventillators with one or more rebates including joining cleat for fixing etc complete all as specified.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) laid on primed surface by torch application complete all as specified.

M&L for 75mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in subbase finished to receive floor treatment.

M&L for PCC 75mm thick PCC 1:3:6 type C-2 (40mm graded stone aggregate) as in plinth protection with 10mm wide and 30mm deep grooves at every 2.5mt interval filled with bitumastic and finished smooth even and smooth without using extra cement.

M&L for galzed ceramic coloured tiles in vertical surfcaes 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectanguliar) area of each tile exceeding 0.06sqm but not exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match

M&L for 5mm thick internal ceiling plaster in CM (1:3) on concrete surfaces finished even and smooth without using extra cement.

M&L for 10mm thick internal plaster in CM (1:6) on concrete surfaces finished even and smooth without using extra cement.

M&L for 15mm external plaster in CM (1:4) on concrete surfcaes finished even and smooth without using extra cement.

M&L for 10mm thick backing coat in CM (1:4) on concrete surfaces finished to receive tile treatment.

M&L for 15mm thick screed bed or bedding layer of Cement mortor (1:6) for laying floor finishes.

M&L for preparation of newly pastered surfcaes in ceiling and applying three coats of white wash.

M&L for preparation of newly plastered surfaces on walls and applying three coats of white wash.

M&L for prearation of newly plasted surfaces on walls, roof projections, chajjas etc and applying two coats of cement based paint over a coat of white cement primer.

S&F 3mm thick figured glass pin head type and glazing with oil putty in squares n exc 0.5m sqm in each pane.

S&F white coloured , three layered rotational moulded polythlene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position with and including GI tank nipples of appropriate dia for inlet and outlet etc all as specified in SSR Part I

S&F 20mm ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed.

S&F 32mm dia waste fttings, brass chromium plated for glazed ware basins with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed.

S&F grating square 150mm size of PTMT (minimum weight 100gms).

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms)

S&F liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms).

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F 75mm bore PVC (SWR) pipes single socketed in any lenghts with rubber vring joints, laid in trenches or in floors.

Description all as in Sl Item No 74 above but fixed to walls

S&F 110mm bore PVC (SWR) pipes single socketed in any lenghts with rubber vring joints, laid in trenches or in floors.

Description all as per Sl Item No 76 above but fixed to walls

S&F 75mm bore PVC (SWR) bends any radius

S&F 75mm bore PVC (SWR) bends any radius provided with access door

S&F110mm bore PVC (SWR) bends any radius

S&F110mm bore PVC (SWR) junction single(Single T) equal or unequal provided with access door.

S&F110mm bore PVC (SWR) vent cowl.

S&F 75mm diameter of outlet cast iron Nahani Trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete.

S&F white coloured vitreous china wash down water closet pan (pedestal pattern) etc complete all as specified and directed.

S&F white coloured plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device.

S&F 10litres capacity PVC valveless syphonic action type flushing cistern, low level, white with inlet, ball valve, float and handle including brackets.

S&F vireous china wash basin, white, flat back, size 550x400mm with and including brackets etc complete.

M&L for 20mm bore galvanised tubes medium grade with all fittings fixed to walls and ceilings or laid in floors.

M&L for 15mm bore galvanised tubes medium grade with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F 15mm bore dia fancy type chromium plated bib taps screwed down, screwed for iron pipe or brass ferrule and fixed.

S&F 15mm bore dia fancy type chromium plated pillar taps, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe etc complete.

S&F 15mm bore dia fancy tpe chromium plated stop valves, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed.

S&F brass chromium plated shower rose 125mm size.

S&F 20mm bore dia Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

M&L for 20mm bore galvanised tubes medium grade with all fittings laid in trenches

Cutting existing 20mm bore steel tubing for additions or alterations (each cut measured) necessarily done in position without taking down.

S&F 20mm bore dia Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

M&L for cement concrete (1:2:4) type B-0 (12.5mm graded stone aggregate) as in surface channels.

M&L for cement concrete cast-in-situ (1:3:6) type C-1 (20mm graded stone aggregate) as in copings including use and waste of formwork as required.

M&L for precast concrete (1:2:4) type B-1 (20mm graded stone aggregate) as in Manhole cover slabs including use and waste of formwork as required. Note:- Reinforcement shall be measured and paid under respective the items.

M&L for plain cement concrete (1:4:8) type D-2 (40mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia pipes

M&L for 10mm thick internal plaster in CM (1:4) on concrete surfaces finished even and smooth without using extra cement.

M&L for 15mm external plaster in CM (1:4) on concrete surfcaes finished even and smooth without using extra cement.

M&L for 150mm internal diameter of pipe salt-glazed stoneware drain pipes laid in trenches and jointed as specified.

M&L for construction of 10 Users capacity septic tank, excavation in any type of soil/rock, foundation in PCC (1:2:4) PCC solid block masonry in CM (1:4), RCC slab covers including RCC precast manhole cover, vent shaft and sludge chambers etc complete all as shown in Drg No CEAA/TD/116 sheet No 1/6 to 6/6.

M&L for construction of soakage wells exc in any type of sopil/rock, foundation in PCC 1:3:6 walls of honey combed solid PCC block masonry, RCC cover and filling with brick bats complete of size 1.20m dia x 3.00m deep all as shown in TD Drg No CEAA/TD/80 sheet No 1/2 to 2/2.

M&L for point wiring for controlled by one switch with PVC insulated but unsheathed single core FRLS multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) in and including non metallic rigid PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes(as per site reuirment) including providing new 3 mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated FRLS copper conductor cable of 1.5 Sqmm with green insulation as earth wire and connected to earth dolly complete all as specified and directed. (a) One light point controlled by one, one way switch

(b) Description all as per Srl item No 108 above but One fan point controlled by one, one way switch

(c) Description all as per Srl item No 108 above butOne socket outlet 3 Pin, 6 Amp on independent board

(d) Description all as per Srl item No 108 above but One socket outlet 3 Pin, 6 Amp on same board.

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 2.5 Sqmm (nominal area) in and including PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC cassing capping on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel terminal/wooden boxes(as per site requirment) including providing new 3 mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated FRLS copper conductor cable of 2.5 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board.

09. S&F switch piano flush type single pole one way 5 Amp (ISI Marked)

S&F switch piano flush type single pole one way 15 Amp (ISI Marked)

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked)

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked )

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked)

supply and fix 6 watt LED Bulk head fitting in engineering plastic housing with clear prismatic diffuser cat part No CG80IBWLED of make : C&S or equivalent in Syska/Philips/Bajaj including LED 6 watt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed by Engineer-in-Charge.

supply & fix following type/rating MCB’s including necessary connection as under:- (a) S & F MCB, 6 to 32 Amp, SP, 240 Volt Make : Legrand /Schneider/Siemens/C&S

Description all as per srl item No 115 above but S&F MCB, 40 to 63 Amp, SPN, 240 Volt Make :Legrand /Schneider/Siemens/C&S

Supply and fix LED decorative box type light fitting 20 watt cat part No DMLN1LT8-16 Make : Crompton Greaves or equivalent in Bajaj/Philips with LED Tube rod 20 watt cat Part No LTT8-20 of make - Crompton Greaves or equivalent in Bajaj/Philips along with all accessories, pre-wired fixed on wall/ceiling and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed by Engineer-in-charge.

Supply & fix Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 4 way (2 + 2 way) single pole and neutral link cat Part No DSDMSHMSIW06000 of Make - STANDARD equivalent in Legrand/Indoasian/Siemens/Schneider complete all as directed by Engineer-in-Charge.

Supply & fix 300mm exhaust fan including making holes in to the wall as per fan size and making good the disturved surfaces all as directed by Engineer-In-Charge

CHANDRAENTERPRISES