GENERAL-DAM SAFETY-CHULLIYAR DAM-Urgent rectification work of River sluice shutters -General Mechanical Work

Amount

Repair and Maintenance of Water escape river shutters and Canal shutters

15.1:Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer - in- Charge.

4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

13.2.1:15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

OD14058/2025-2026:Dismantaling of the shutters (where there is road acess to the point ) from the grooves and stacking including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%).,

OD14059/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges.,

OD14060/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges.,

OD14061/2025-2026:Supply of MS round bar including cost of conveyance charges.,

OD29729/2025-2026:Supply of G.I. pipes 32 mm dia

OD29723/2025-2026:SUPPLYING & STACKING of Dia 25mm NB (1") G.I Pipe

OD14065/2025-2026:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied.,

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD14063/2025-2026:Providing EN-8 Screw Rod 7.50 Tonne Capacity 4.00 Mtr lift Screw Rod having one number of EN-8 Screw Shaft having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all material, labour, hire charges and conveyance. (63mm Dia Screw rod ).,

OD14064/2025-2026:Providing of WORM & PINION having a lifting speed of around 5.00 cm/min for hand operation. having gearbox wall thickness of 12mm for side, 16mm for top and 24mm base. Top plate fixed with minimum 8 nos of M12 bolt , including cost of Mechanical stoper, Locking arrangement, Operating handle and all other materials, labour, hire charges and conveyance.

OD14066/2025-2026:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , ladder etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied.,

OD14067/2025-2026:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE.,

OD14069/2025-2026:SUPPLYING and STACKING of PAD LOCK.,

OD32475/2025-2026:DRILLING (up to depth of 200mm for MS/SS/TMT rod dia. 8mm to 25mm) and FASTENING with MS/SS/TMT rod in concrete/Stone including conveyance and labor charges complete. [excluding cost of materials already supplied.](#)

OD29999/2025-2026:Anchoring the MS/SS rebars into the drilled hole using CHEMICAL ADHESIVES, including cost of hire charge of machine, cost of chemical adhesive and labour. (#)

OD30003/2025-2026:Supply of Bolt and Nut up to 300mm Length including cost of conveyance.

OD30038/2025-2026:SUPPLYING and FIXING of TOWER BOLT(#)

OD30039/2025-2026:SUPPLY of BUTT HINGE(#)

P.Damodaran, G.R.Industries (BID ID -2433657)

Bidder Name

Kinanath V P

P.Damodaran, G.R.Industries