Re Construction of Govt Primary School Building GPS Sardhar Education Block Rewalsar Distt. Mandi Himachal Pardesh Sub Head Construction of remaining civil works W Sand SI in Ground Floor Septic tank and colomn of First Floor etc

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement : four sand : eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) in foundation and plinth including curing complete excluding the cost of form work but including carriage of material with in all leads, lift, and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level, excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm (twenty millimeter) nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforcement cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° (fifteen degree) up to all floor level excluding the cost of centring, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed vibrated and curing complete including carriage of materials with in all leads, lift and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in all height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:-

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, posts and struts square, rectangular or polygonal in plan as required.

Stairs, (excluding landings) except spiral stair cases.

Edges of slab and breaks in floor and walls under 20 cm wide as required.

Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including straightening, cutting ,bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge

Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in Cement mortar 1:4 (1 cement :4 coarse sand) including curing complete and carriage of material with in all leads, lifts and other incidentals

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in cement mortar 1:4 (one cement : four sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing Sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 35 mm thick, Second class teak wood glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 35 mm thick, Second class teak wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with ISI marked M.S. pressed butt hinges bright finished of required size including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing Float glass panes 5mm thick glass pans (weight not less then 12.5 kg/sqm), panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals.

Providing extra for lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)complete including carriage of materials with in all leads, lifts and other incidentals.

Providing extra for cutting rebate in flush door shutters (Total area of the shutter to be measured) complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Stainless Steel extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing 250x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

200 x 10 mm (two hundred X ten mili metres)

100 x 10 mm (one hundred fifty X ten mili metres)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

125 mm (one hundred twenty five milimeter)

100 mm (one hundred milimeter)

Providing and fixing Twin rubber stopper aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all omplete. Fixed to openings /wooden frames with rawl plugs screws etc including carriage of material with in all leads, lifts and other incidentals.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting steel work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying vitrified floor tiles size of 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to IS: 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours and shades, laid on 20 mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying Vitrified tiles 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement : three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

40 mm thick with 20 mm nominal size stone aggregate Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand:4 graded stone aggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete including curing and carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. including carriage of materials with in all leads, lifts and other incidentals.

Flamed finish Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing edge moulding to 18 mm thick granite stone, marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

25 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) including curing, carriage of material with in all leads, lifts and other incidentals.

Providing and fixing Single socketed pipes 110 mm dia (one hundred ten mili metre) with minimum pressure of 4.5 kg/sqm on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories of working pressure 4 Kgf/sq cm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads & lifts and other incidentals.

110 mm bend (one hundred ten mili metres)

110 mm shoe (one hundred ten mili metres)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty X fifty X fifty mili metres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete. including carriage of material with in all leads, lifts and other incidentals.

110 mm diameter (one hundred ten mili metres)

6 mm (six millimeter) thick cement plaster to ceiling in cement mortar 1:3 (one cement : three sand) including carriage of material with in all leads, lifts and other incidentals.

15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete / stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and / or rounded angles not exceeding 80 mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement : six sand ) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 15 mm wide and 15 mm deep groove. Outer face back side after deduction complete in all respect.

Providing and applying white cement based putty of average thickness 1 mm (one milimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with In all leads, lifts in all floors and other incidentals completes as per direction and to the entire satisfaction of Engineer-in-Charge.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: including carriage of material with in all leads, lifts and other incidentals as per the directon of engineer in charge.

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera/hindware/parryware make with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin cera/hindware/parryware make of 430 x 260 x 350 mm (four hundred thirty X two hundred sixty X three hundred fifty milimeters) and 340 x 410 x 265 mm (three hundred forty X four hundred ten X two hundred sixty five milimeters) sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 lt. white P.V.C automatic flushing cistern as required including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing White Vitreous China Wash basin cera/hindware/parryware make size 550 x 400 mm (five hundred fifty X four hundred mili meters) with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china pedestal for wash basin cera/hindware/parryware make completely recessed at the back for the reception of pipes and fittings as required including carriage of material with in all leads, lifts and other incidentals .

Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink 510 mm x 1040 mm bowl depth 225 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. The sample of heavy duty jet should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm stainless steel grating heavy duty for gully trap. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 450 mm beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 120 x 5 mm heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing CP brass heavy duty toilet paper holder complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete in all respect (cost of water meter and stop cock to be paid separately).

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing 15 mm nominal bore C.P. brass bib cock of jaquar/jal/ess ess make of approved quality conforming to IS:8931 : The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 690 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The sample quality & series should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Inside dimension 455 mm x 610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Inside dimensions 455 cm x 610 cm and 45 cm deep for single pipe line :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. Internal work - Exposed on wall. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge including carriage of material with in all leads, lifts and other incidentals.

15 mm nominal outer dia Pipes.

20 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge as required Concealed work, including cutting chases and making good the walls etc. including carriage of material with in all leads, lifts and other incidentals.

15 mm nominal outer dia Pipes.

20 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge for external work including carriage of material with in all leads, lifts and other incidentals.

15 mm nominal outer dia Pipes.

20 mm nominal outer dia Pipes.

Providing and fixing 20 mm PPR unions.

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x 1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.

Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe). complete including carriage of material with all leads ,lifts and other incidentals.

External work work for providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

15 mm dia nominal bore.

20 mm dia nominal bore.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete.

110 mm x 75 mm

Providing and fixing PVC Poly plast sewerage & drain pipe of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete including carriage of material with in all leads, lifts and other incidentals.

110 mm dia.

75 mm dia.

Single equal branch of required with oval access door insertion rubber washer 3mm thick bolts and nuts. "PVC Door Tee"

110 mm dia.

75 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Door Bend"

110 mm dia.

75 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Collar"

110 mm dia.

75 mm dia.

Providing and fixing PVC Poly plast sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme / centimeter metre square) fitting & accessories including filling the joints with approved adhesive complete. "PVC Plain Bend"

110 mm dia.

75 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Plain Tee"

110 mm dia.

75 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Cowel"

110 mm dia.

75 mm dia.

Supplying and fixing C.I. cover without frame for manholes :455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. including carriage of material with in all leads, lifts and other incidentals.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar including carriage of material with in all leads, lifts and other incidentals.

Making soak pit 2.5 m diameter 3.0 metre deep with 45x 45 cm drybrick honey combs haft with bricks and S.W. drain pipe 100 mm diameter,1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. including carriage of material with in all leads, lifts and other incidentals.

Please Enable Macros to View BoQ information