MP-LBC-Fabrication, painting and erection of SS C-groove, MS shutters and hoisting mechanism at CH 09 800 Kalmandapam 2nos shutters and CH14 400 Thassarak 1no shutter

Amount

Providing BUND and removal of bio wastes

od5576/2020_2021/MH : Providing BUND - 1m bottom width and 0.5 m height using empty gunny bar polythene bag filled with earth for an total length of 1 m includinglabour.Vol. of bund 1*0.5*1=0.5m3No. of bags 0.5/0.027 =19nos

od5578/2020_2021/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

od5577/2020_2021/MH : Removing BUND - 1m bottom width and 0.5 m height using empty gunny bar polythene bag filled with earth for an total length of 1 m.Vol. of bund 1*0.5*1=0.5m3No. of bags 0.5/0.027 =19nos

DISMANTLING existing shutter and hoisting bridge

od5579/2020_2021/MH : Dismantling of the Canal Shutter ( Less than 2 Tonne weight ) including . in correct alignment ; setting and aligning complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

DEMOLISHING cement concrete manually, FORM WORK and CONCRETING

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.2 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

85.107 : Supply of MS round bar including cost of conveyance charges

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Supply, fabrication and erection of MS and SS EMBEDDED PARTS.

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od5585/2020_2021/MH : Fabrication and supply of Embedded parts of CANAL GATE ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od5586/2020_2021/MH : ERECTION of the EMBEDDED PARTS of CANAL SHUTTER ( Less than 2 Tonne weight ) including . in correct alignment ; setting and aligning complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

od5587/2020_2021/MH : Fabrication, Supply, erection and assembling in correct position and alignment by welding SS EMBEDDED PARTS in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

Supply, fabrication and erection of MS SHUTTERS

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

od5611/2020_2021/MH : Fabrication and supply of Structural steel CANAL GATE ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od5612/2020_2021/MH : ERECTION of the CANAL SHUTTER ( Less than 2 Tonne weight ) including . in correct alignment ; setting and aligning complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Supply of SCREW ROD and WORM & PINION with MECHANICAL STOPPER

od5895/2020_2021/MH : Providing EN-8 SCREW ROD (dia. 63 mm) 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN -8 screw shaft,worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance.

od5897/2020_2021/MH : THREAD LESS portion of the screw rod (per metre rate)

od5898/2020_2021/MH : SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

od5899/2020_2021/MH : Providing of WORM & PINION having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance.

Supply, fabrication and erection of HOISTING BRIDGE and HANDRAILS.

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od6012/2020_2021/MH : SUPPLYING & STACKING of Dia 32 mm G.I. PIPE

od6007/2020_2021/MH : Supply of BOLT and NUT up to 300mm Length including cost of conveyance.

od6009/2020_2021/MH : SUPPLYING & FIXING of TOWER BOLT

od6010/2020_2021/MH : BUTT HINGE

od6011/2020_2021/MH : SUPPLYING and STACKING of PAD LOCK.

od6005/2020_2021/MH : Fabrication and supply of HOISTING BRIDGE and platform of CANAL GATE ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od6006/2020_2021/MH : ERECTION of the HOISTING BRIDGE and platform of canal shutter ( Less than 2 tonne weight ) including handrails , ladder and platform etc. in correct alignment and anchoring it ; setting and aligning complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

PAINTING all the surfaces of the EMBEDDED PARTS, SHUTTER and HOISTING BRIDGE with EPOXY coal tar black.

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

P.Damodaran, G.R.Industries

Bidder Name

ROLF ENGINEERING CO.

P.Damodaran, G.R.Industries