SPECIAL REPAIR TO BLDG NO P-95 AT AF STN KASAULI UNDER GE (AF) CHANDIGARH

Amount

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed by Engineer-in-Charge.

Taking down wooden shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm from steel frame/wooden frame and refixing after easing and adjusting and refixing builders harware in the same opening complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge.

M&L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in C.M 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid joint free ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and directed by Engineer-in-Charge.

M&L for Joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and directed by Engineer-in-Charge.

M&L for Joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,in skirting etc set and jointed in neat cement slurry over 10 mm thick screed bed in cement mortar 1:3 and pointed in white/coloured cement to match the shade complete all as specified and directed by Engineer-in-Charge..

M&L glazed ceramic coloured/printed tiles 450mm x 350mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:3) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards(fibre pulp,insulation,etc)or insulation boards/slabs/blankets any thickness, including cover fillets and snap grid complete all as specified and directed by Engineer-in-Charge.

S&F, Metal suspended ceiling system OREO GI laid in plain 600X600X0.50 mm (tegular) edge tiles in global white colour to be laid on strong 24mm T-section flanges colour white having rotary stitching on the main runner with web height of 38mm. Note:(i) To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit at 1200mm maximum centre.The first/last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200x600 mm mould.Cut cross tees longer than 600mm require independent support. 600X600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm,secured to walls at 450mm maximum centres. (ii) Suspension system accessories consisting of HLC sleeve anchor fasterners of thread size 6.50 mmx25/5 with soffit cleat made of galvanised steel of size 27x37x25x1.60mm & level clip in dimensions of 85x30x0.80 mm with 4mm GI wire complete all as specified & directed. Make : High steel,Armstrong & Dexune.

Dismantling plain or corrugated steel sheeting of any thickness as in roof coverings complete all as specified and directed by Engineer-in-Charge.

S&F pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified as in rain water gutter.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L, Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

S&F Rolled mild steel sections as in posts, main and cross beams, hip and jack rafters; purlins, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. Conforming to Fe-290(GdeE-165) complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F, 110mm PVC (SWR) reducers complete all as specified and directed by Engineer-in-Charge.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for., removal of exccavated materila n exc 50 mtr and deposited where direcd at a level n exc 1.5 m above the starting point complete all as specified and directed by Engr -in-Charge.

M&L for Form work to chullah hoods, chajjas, troughs and similar items including edges flat and rough finished complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed by Engineer-in-Charge.

Material and labour RCC 1:1.5:3 type A-1 using 20 mm graded stone aggregate as chajja, fins, louvers, roof projection ,beam and lintel after removing of loose concrete and preparation of surface by application of derusting chemical such as Dr fixit rust remover or equivalent and welding additional main bars/distribution bars by inserting to adequate depth in beam by drilling , priming reinforcement bar old/new with a coat of anti corrosion Nitozinc primer of M/s FOSROC, including necessary scafolding as required height upto 3.5 Mtr, complete all as specified and directed. Note: 1. Rates include for necessary scafolding etc. 2. Reinforcement will measured and pid separately. 3. Notozince primer will be paid separately

Material and labour RCC 1:1.5:3 type A-1 using 20 mm graded stone aggregate as chajja, fins, louvers, roof projection ,beam and lintel after removing of loose concrete and preparation of surface by application of derusting chenicla such as Dr fixit rust remover or equivalent and welding additional main bars/distribution bars by inserting to adequate depth in beam by drilling , priming reinforcement bar old/new with a coat of anti corrosion Nitozinc primer of M/s FOSROC, including necessary scafolding as required height of 3.50Metre and upto heigth 8.00 Metre, complete all as specified and directed. Note: 1. Rates include for necessary scafolding etc. 2. Reinforcement will measured and pid separately. 3. Notozince primer will be paid separately

Material and labour for anti corrosive primer, Nitozinc of M/s FOSROC or equivalent Make/Brand as approved by GE, complete to old de-rusted reinforcement bars in chajjas all as specified and directed.

M& L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as in chajja, ceiling etc including two coats of Cement base paint on new surfaces complete all as specified and directed by Engineer-in-Charge. Note: Height upto 8.0 Mtr

Demolition of cement concrete (unreinforced) of any description in any position complete all as specified and directed by Engineer-in-Charge.

Material and Labour, Water Proofing Treatment to sunken portion of WCs, bathroom etc, complete all as specified and directed, comprising as under:- (a) Applying neat cement slurry @ 1.3 Kg/Sqm of surface, including wire brushing, cleaning, washihg and preparing roof surface & sides of walls. (b) 15mm thick plaster in Cement Sand Mortar (1:3) mixed with integral water proofing compound @ 2% by weight of cement on floor and wall, finishing the surfaces even and smooth without using extra cement. The surface shall then be cured and allowed to dry. Note : Supply only water proofing compound shall be measured and paid separately. (c) First layer of slurry of Cement @0.488 Kg/Sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer will be allowed to air cure for 4 hrs. (d) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with Acrylic based polymer modified cementitious composite compount @ 0.126 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hrs.

M&L, PCC, 1:5:10 , type E-2 , using 40 mm brick coarse aggregate as in sunken portion,complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound .

M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in floorings, as in sub base of floor tiles in ground floor complete all as specified and directed by Engineer-in-Charge.

supply and fixing 40 mm dia GI pipe , medium grade as in spout for sunken floor,fixed as in wall inside end fixed with wire netting and external bevelled edge at 45 degree, complete all as specified and directed.

Demolition of cement concrete (unreinforced), of any description in ground floor and paving (below or above ground level), not exceeding 15cm thickness, including removal of rubbish/ debris outside MoD land, complete all as specified and directed.

Material and labour, plain cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection, 75mm thick, (laid to slope of 1:20), finished even and smooth without using extra cement, laid with 10mm wide joints to full depth @ 3m c/c and at corners, filled with mastic mortar, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces of ceiling/ soffits, etc, any description including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish outside MoD land, complete all as specified and directed.

Material and labour, rendering 15mm thick plaster in cement mortar (1:6), on brick or concrete surfaces of walls, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour, rendering 10mm thick plaster in CM (1:3), as on ceiling of slabs, soffits and sides of beams, chajjas, etc, finished even and smooth without using extra cement, complete all as specified and directed.

Material and Labour 5mm thick plaster in CM (1:3) on brick or concrete surface using WPC @ 3% by weight of cement and finishing the surface even and smooth without using extra Cement over and including 10mm thick backing coat in CM (1:4), complete all as specified and directed. Note(s) : (i) WPC will measured and paid separately as supply only.

Dismantling of cast iron pipes 100mm / 75mm dia, jointed in cement mortar/run lead and taking out of trenches/from walls, as required, complete all as specified and directed.

Supply and fix, Cast iron (sand cast) soil, waste and vent pipes, 75mm bore, in any length with or without ears, with cement joints, laid in trenches or under floors as required, complete all as specified and directed.

Supply and fix, Cast iron (sand cast) soil, waste and vent pipes, 75mm bore, in any length with or without ears, with cement joints, fixed to wall with MS holder bats/clamps including nut and bolts as required, complete all as specified and directed.

Supply and fix, Cast iron (sand cast) soil, waste and vent pipes, 100mm bore, in any length with or without ears, with cement joints, laid in trenches or under floors as required, complete all as specified and directed.

Supply and fix, Cast iron (sand cast) soil, waste and vent pipes, 100mm bore, in any length with or without ears, with cement joints, fixed to wall with MS holder bats/clamps including nut and bolts as required, complete all as specified and directed.

Material and labour, Cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, suitable for 100mm pipe, complete all as specified and directed.

Material and labour, cast iron bend (any radius), diminishing pieces or tapers suitable for 100mm bore pipes, ISI marked, with cement joints, complete all as specified and directed.

Material and labour, cast iron bend (any radius), diminishing pieces or tapers suitable for 75mm bore pipes, ISI marked, with cement joints, complete all as specified and directed.

Material and labour, Cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, suitable for 75mm pipe, complete all as specified and directed.

S&F PVC (SWR) floor trap, 75mm dia outlet, plain with grating incl jointing with solvent cement., complete all as specified and directed.

Disconnecting of geyser carefully and re fixing the same including all necessary fittings, complete all as specified and directed.

Disconnecting/ dismantling & taking down of old u/s water storage tanks with inlet, outlet with plug, ball valve, over flow pipe, capacity exc 250 litre but not exc 500 litre and removal from site to store for reuse or credit, complete all as specified and directed.

Supply and fixing/hoisting, rotational moulded polyethylene (HDPE) water storage tanks (cylindrical vertical with closed top), 500 litres capacity, triple layered’, hoisted and fixed in position including inlet, outlet and drain pipe with plug, brass ball valve with float suitable for 20mm bore dia pipe, complete all as specified and directed.

Taking up or down existing steel water tubing with standard fittings, and connections, 15mm bore, for re-fixing or removing from site to store for reuse or credit, including dismantling standard fittings, complete all as specified and directed.

Supply and fix, galvanized steel water tubes, 15mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Fixing only, old steel water tubing, 15mm bore, with all standard fittings, in new or old position (walls, ceiling, floors etc), complete all as specified and directed. Note(s) : (i) Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc.,

Taking up or down existing steel water tubing with standard fittings, and connections, 20mm bore, for re-fixing or removing from site to store for reuse or credit, including dismantling standard fittings, complete all as specified and directed.

Supply and fix, galvanized steel water tubes, 20mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Fixing only, old steel water tubing, 20mm bore, with all standard fittings, in new or old position (walls, ceiling, floors etc), complete all as specified and directed. Note(s) : (i) Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc.,

Supply and fixing, Vitreous china wash hand basin, white, flat back, size 550mm x 400mm including brackets and cutting for and pinning in ends of brackets, complete including CP brass waste coupling, PVC waste pipe, including taking down old WHB and removal from site to store for reuse or credit, complete all as specified.

Supply and fixing, pillar taps, cast copper alloy, chromium plated, fancy type, with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shank and fly nuts, screwed for iron pipe 15mm bore dia and fixed to WHB and connections to iron pipe, fixed as in repairs, complete all as specified and directed.

Taking down and re-fixing only after repairs, old servicable pillar taps, cast copper alloy, chromium plated, fancy type, with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shank and fly nuts, screwed for iron pipe 15mm bore dia and fixed to WHB and connections to iron pipe, including cleaning, bleaching and washing the serviceable pillar taps & changing washers, complete all as specified and directed.

Supply and fix, Vitreous China wash down water closet EWC Pan (pedestal pattern), white, including fixing bolts, plastic seat closed pattern with flat bottom and cover (White/black), PVC/VC trap & 32mm bore PVC flush pipe, and with mild steel chromium plated or anodised hinging devices, connected to drain outlet, & anti syphonage pipe including taking down old EWC and removal from site for credit or disposal out of MoD Land, complete all as specified and directed.

Supply and fix, chromium plated steel jet pressure unit alongwith suitable size and of appropriate length PVC pressure pipe, fixed to EWC/ IWC, fixed as in repairs, complete all as specified and directed.

Taking down and re-fixing after necessary cleaning, bleaching, washing & changing minor parts as washers etc., 10 litre capacity low level flushing cistern, complete including PVC bend/ flush pipe, making all connection, fixed as in, complete all as specified and directed.

Supply and fixing, Stop valves/angle cock valves, cast copper alloy, screwed down high pressure, fancy type, chromium plated, screwed both ends for iron pipe or for unions of 15mm bore dia, fixed as in repairs, complete all as specified and directed.

Supply and fixing, bib taps, cast copper alloy, screwed down high pressure, screwed for iron pipe or for brass ferrule of 15mm bore dia, fixed as in repair including removal of old bib tap to store for reuse or for credit, complete all as specified and directed.

Taking down and re-fixing only, Bib taps, Cast copper alloy, fancy type or ordinary, screwed for iron pipe or for unions of 15mm bore dia, fixed as in repairs after proper cleaning, bleaching and washing & changing the washers, complete all as specified and directed.

Supply and fix, PVC connection 15mm size with PTMT nuts, of length 450mm, fixed as in repairs, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), of any description, exceeding 1.50Sqm but not exc 4.0Sqm each, and removal to store for reuse or credit, including cutting hole for taking out hold fast and making good disturbed portion in CM (1:3) or in PCC (1:3:6) type C-1, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), of any description, not exc 1.50Sqm each, and removal to store for reuse or credit, including cutting hole for taking out hold fast and making good disturbed portion in CM (1:3) or in PCC (1:3:6) type C-1, complete all as specified and directed.

Supply and fixing in opening, Solid PVC Door Frame of size 50mmx47mm, made out of 5mm thick plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawing in SSR Part-II, complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat mouleded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rain, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supling & fixing in the frame at site as per specification & drawing.

Supply and fixing, pressed steel frames for doors with one or more rebate, size of frame 125mm x 60mm, made out of 1.25mm thick MS Sheet, including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed. Note(s) :- (i) The size dimension and type (profile) of frames shall be as per relevant IS. (ii) PCC filling in frame shall be measured and paid separately.

Supply and fixing, factory made 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, chemically treated against termite infestation, complete all as specified and directed

Material and labour, cutting holes in brick walls built in cement mortar for inserting holdfasts, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exceeding half brick but not exceeding one brick, and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required, complete all as specified and directed.

Supply and fix, steel window box type, primer coated, comprising ERW Hollow `P’ section of size 60mmx25mm of 1.25mm wall thickness frame, single rebated, skeleton shutter (suitable for wire gauge), made of ERW section 50mmx20mm of 1mm wall thickness, and operated leaf side hung, without glazing bars but including Flat iron 12mmx03mm for securing wire mesh, dove tailed or welded/revitted welded to frame of shutter, and openable shutter prepared to receive wire gauge, complete , including cutting holes four Nos for each window and making good disturbed portion in PCC (1:3:6) type C-1, including following fittings welded to frame/shutter :- (a) Hold fast 150mm long out of 25x6mm flat iron made to shape - 04 Nos each window (02 Nos on each side). (b) Handle of `Z’ section 20x25mm, 100mm long - 01 No (each leaf). (c) MS tower bolt 150mm long - 02 Nos (each leaf). (d) `Z’ section 20x25mm, 100mm long stopper - 01 No (each leaf). (e) Cleat 55mm long of hollow square section 15mmx15mm of 24 gauge wall thickness, welded to hinge of 55 mm size - 01 No (per leaf). (f) MS box type hinges of 75mm size - 03 Nos (per leaf). (g) Fabrication and fixing compete as per approval & drawing. Note(s) : (i) Wire gauge and painting shall be measured and paid separately under respective items. (ii) Design shall be approved from the Engineer-in-Charge as per Drg No CEAF/STD-185/2012 sheet 1/2 to 2/2 before fabrication and bulk order to the manufacturer.

Supply and fix, steel window box type, primer coated, comprising ERW Hollow `P’ section of size 60mmx25mm of 1.25mm wall thickness CRCA sheet frame, single rebated, skeleton shutter (suitable for glazing), made of ERW section 50mmx20mm of 1mm wall thickness, and operated leaf side hung, with two Nos glazing/sash bars of `T’ section 20x3mm welded to frame of shutter, prepared to receive glass, complete with one shop coat of zinc chorme or red oxide primer, including cutting holes four Nos for each window and making good disturbed portion in PCC (1:3:6) type C-1, including following fittings welded to frame/shutter:- (a) Hold fast 150mm long out of 25x6mm flat iron made to shape - 04 Nos each window (02 Nos on each side). (b) Handle of `Z’ section 20x25mm, 100mm long - 01 No (each leaf). (c) MS tower bolt 150mm long - 02 Nos (each leaf). (d) `Z’ section 20x25mm, 100mm long stopper - 01 No (each leaf). (e) Cleat 55mm long of hollow square section 15mmx15mm of 24 gauge wall thickness, welded to hinge of 55 mm size - 01 No (per leaf). (f) MS box type hinges of 75mm size - 03 Nos (per leaf). (g) Fabrication and fixing compete as per approval and drawing. Note(s) : (i) Glazing and painting shall be measured and paid separately under respective items. (ii) Design shall be approved from the Engineer-in-Charge before fabrication and bulk order to the manufacturer(s) as per Drg No CEAF/STD-184 of 2012, sheet 1/3 to 3/3.

Supply and fix, factory made box type steel section ventilator, with box type section double leaf shutter for glazing and wire gauze with pintol hinges, 01 No 150mm long Mild Steel tower bolt, steel handle to each shutter (steel handle dovetailed or welded), and with one shop coat of red oxide / zinc chromate primer, complete all as specified and shown in drawing duly fitted with all fittings , welded to frame/shutter including cutting holes for hold fasts & making good in PCC 1:3:6 Type C-1. Note(s) : (i) Wire mesh & glazing shall be measured and paid separately. (ii) Design shall be approved from the Engineer-in-Charge before fabrication and bulk order to the manufacturer(s) as per Drg No CEAF/STD-186/2012, sheet 1/1.

Supply and fixing, stainless steel wire cloth, with 0.36mm nominal dia of wire and average width of aperture 1.40mm, and fixed with stainless steel wire staples, complete all specified and directed.

Material and Labour, mild steel Fe-290 Gde, E-165 'A' quality as in bands, clamps, holdfasts, wall ties and similar articles including fixing bolts as required, complete all as specified and directed.

Supply and fix, stainless steel butt hinges, medium weight, 100mm size, ISI marked, fixed with stainless steel screws to aluminium frame work or PVC doors/frames etc, complete all as specified and directed.

Supply and Fixing, Aluminium anodised, barrel tower bolts 200mm long, powder coated, of extruded section, and fixed to door shutters & frames etc., complete all as specified and directed.

Supply and fixing, 125 mm long, extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and directed.

S&F, Steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia, 100mm size complete all as specified and directed.

Supply and Fixing, Aluminium alloy anodised sliding door bolts 300mm long, with hasp & staple and fixing clips, of sheet cast or fabricated section and plate type, bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all specified and directed.

Supply and Fixing, Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 140mm, complete with vulcanised rubber piece including making sinking in floor, fixed in floor as in repairs, complete all as specified and directed.

Material and Labour, mild steel Fe-290 Gde, E-165 'A' quality, as in guard bars, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; including taking down old rusted guards with frame and removal to store for credit, complete all as specified and directed.

Supply and fixing, stainless steel wire cloth, with 0.36mm nominal dia of wire and avg width of aperature 1.40mm, and fixed to wooden frame/steel frame, including necessary putty, glazing pins, spring clips etc as required, fixed as in repairs and removal of old wire cloth to store yard for reuse or credit, complete all as specified and directed.

Material and labour, applying two coats of synthetic enamel paint over and including a coat of pink primer, on new wooden surfaces over 10cm width or girth, including preparation of wooden surfaces, complete all as specified and directed.

Material and labour, applying one coat of synthetic enamel paint on old painted wooden surfaces over 10cm width or girth, including preparation of wooden surface, complete all as specified and directed.

Material and labour, applying two coats of synthetic enamel paint over and including a coat of red oxide primer, on new steel surfaces over 10cm width or girth, including preparation of steel surfaces, complete all as specified and directed.

Material and labour, applying one coat of synthetic enamel paint on old painted steel surfaces over 10cm width or girth, including preparation of steel surfaces, complete all as specified and directed.

Material and labour, preparation of newly plastered surfaces of walls by stopping of surfaces, levelling/edging the disturbed places using white cement based wall care putty (JK/Birla) and applying two coats of 1st quality oil bound distemper (oil emulsion) over and including a coat of 1.0mm thick white cement based wall care putty(JK/Birla), smoothening with sand paper to obtain regular and smooth surface, and including one coat of alkali resistant primer, complete all as specified and directed. Note:- The rate quoted by the contractor shall be deemed to include use and waste cost of ladder/ wooden platform etc., as may require.

Material and Labour, complete removal of existing treatment/painting on old plastered surfaces of wall using wire brushes & scrappers etc., preparation of surfaces by stopping, levelling/edging the distrubed places using white cement based wall care putty (JK/Birla) and applying two coats of 1st quality oil bound distemper (oil emulsion) over and including a coat of 1.0mm thick white cement based wall care putty (JK/Birla), smoothening with sand paper to obtain regular and smooth surface, and including one coat of alkali resistant primer, complete all as specified and directed. Note : The rate quoted by the contractor shall be deemed to include use and waste cost of ladder/ wooden platform etc., as may require.

Material and labour, preparation of old decorated plaster ceiling surfaces and applying two coats of white wash, complete all as specified and directed. Note : The rate quoted by the contractor shall deemed to include use and waste cost of ladder/ wooden platform etc.,

M & L for preparation of old plastered or unplastered surfaces of walls including cornices and applying two coat of white wash on old decorated surfaces, Complete all as specified and directed by Engineer-in-Charge. Note : The rate quoted by the contractor shall deemed to include use and waste cost of ladder/ wooden platform etc.

Material and Labour, preparation of new plastered surface of ceiling and applying three coats of white wash, complete all specified and directed. Note : The rate quoted by the contractor shall be deemed to include use and waste cost of ladder/ wooden platform etc.,

Material & labour, complete removal of existing / old decoration i.e paint from unplastered/ plastered surfaces of walls using steel wire brushes, scraping down to remove efflorescent salts, grease spots, moulds, moss, etc., including brooming down, washing, rubbing down using sand paper, including stopping of distrubed surfaces, planes/edges with white cement putty & rubbing with sand paper to obtain regular and smooth surfaces, and applying two coats of exterior acrylic emulsion anti weather & anti algae paint (1st quality paint), in disruptive pattern (camouflage) using number of colours as approved, over and including a coat of alkali resistant primer complete all as specified and directed. Note (s): (i) Pattern of camouflage shall be as approved by GE. (ii) Rate quoted by contractor shall be deemed to include the cost of use and waste of necessary ladder, wooden platform etc., as may require to execute work at any height upto 8.00 metre. (iii) Painting work shall stand guaranted against fadding/Peeling off for 05 years & the cost agaist this aspect shall be deemed included in the unit rate quoted for this item.

Material and Labour, 15mm thick Granite (of any type) work (table rubbed and polished) in treads/steps, window-cills, cooking platform and like, set in neat cement slurry @ 3 Kg/Sqm including pointing in white cement mortar (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and ditected.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

S&F 5.5 mm thick, Figured glass, pin head fixed in aluminium frame as in windows/ventilators, complete all as specified.

Demolition of Brickwork or stone/ boulders masonry built in cement or cement lime mortar incl all quions, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed.

Excavation in trenches in hard dense soil n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or shafts, wells, cesspits, manholes, pier holes etc and getting out complete all as specified.

Returning , filling in, including spreading, leveling, watering and well ramming in layer n.exc 25cm depth in layer complete all as specified and directed.

Removal excavated materials to distance n.exc 50 metre and depositing where directed at a level n.exc 1.5metre above the starting pointing in soil,complete all as specified and directed.

Demolition of SGSW drain pipe of any bore with PCC bedding/hunching cradle jointed in cement mortar and taking out of trenches if required with fittings complete all as specified and directed.

M&L cement concrete (1:4:8) type D-2 using 40mm stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipe complete all as specified and directed.

M&L Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointed in cement mortor complete all as specified and directed.

S&F, Door seal wih PVC body & fitted with rubber seal complete all as specified and directed.

S&F in repairs Fibre glass reinforced translucent corrugated sheeting 2mm thick in thickness with two corrugation side lap fixe with L type or J type hooks bolts complete all as specified and directed.

S&F in repair PVC valve less, symphonic action type flushing cistern, low level white including inlet, ball valve, float handle including brackets of 10 ltrs capacity including flush pipe complete all specified and directed by Engineer-in-Charge.

S&F in repars, Prelaminated particle board, interior grade, prelaminated both side (18 to 19mm thick) with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F Extruded Aluminium alloy handles, fabricated type anodised of 75mm long size complete all as specified and directed.

Supply and Fixing in repairs, Harrison rails, mild steel chromium plated, 25mm dia, in short lengths 1.0 to 2.0 metre, including fixing bracket, steps roller etc, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including GI earth wire on batten or in PVC conduit or in MS Conduct including fixture and fittings such as switches, ceiling roses, pendants, fan regulators, bell/buzzers, sockets etc, removing materials to store for keeping in safe custody for reuse or for taking credit (credit for above items shall be made as per conditions separately) and making good disturbed surface of walls, roof/ceiling, etc (to match the existing), complete all as specified and directed.

Taking down carefully existing wooden board/ main switch board, MCB DB boxes with MCBs, MCCB sheet metal boxes, light fittings, ceiling fans, exhaust fans etc., of any size & any capacity, and removal to store for re-use or credit, complete all as specified and directed.

Taking down carefully, sub main wiring from wall/ceiling, of any size of copper or aluminum, on wooden batten and or through rigid conduit including GI wire and making good the distrubed surfaces of walls, roofs/ceiling, floors etc to matching the existing, complete all as specified and directed. Note : For item No 117 to 119: All the materials obtained from taking down against these items shall be recorded in MB duly signed by Engineer-in-Charge and contractor as actually obtained at site by giving details of each item.

Material and labour, point wiring with two single core multi stranded copper conductor 1.5Sqmm (nominal area) PVC insulated unsheathed FRLS colour code cable of 1100volts grade drawn through and including non metalic rigid PVC conduit medium duty of suitable size with all standard fittings such as Tee junction, bends etc, conduit concealed in wall & fixed on ceiling including M.S. sunken boxes of suitable size made out of 1.6mm thick sheet duly painted with anticorrosive paint, for housing switches, fan regulators etc. with PVC cover sheet 3mm thick including one 1.5Sqmm (nominal area) multi stranded copper conductor PVC insulated unsheathed FRLS colour code cable of 1100volts grade for earth continuity, as for one light/exhaust fan/bell point or fan point (through regulator), controlled by one switch, complete all as specified and directed. Note(s) : (i) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required. (ii) Switches and fan regulator etc., shall be measured and paid separately. Circuit wiring from distribution board to switch board shall be deemed included in the quoted rate of point wiring.

Supply and fix, switch piano, flush type, single pole, one way, 5Amps, 230volts, complete all as specified and directed.

Material and labour, sub main wiring with two single core 4Sqmm (nominal area) stranded copper conductor FRLS PVC insulated and unsheathed 1100 volts grade cables, drawn through and including non metalic PVC rigid conduit medium grade of suitable size with all standard fittings such as tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, concealed, including one run of continuous PVC insulated stranded copper conductor FRLS 1100 volts grade cable 2.5Sqmm (nominal area) for earth continuity, complete all as specified and directed. Note :- (i) Two runs of 4Sqmm main cable + one run of 2.5Sqmm cable for earth continuity & conduit shall be measured as one unit/one Running Metre.

Supply and fix in repairs, Lamp Holder, insulated body, bakelite/ PVC/Polycarbonate type, with back plate suitable for batten fittings/ conduit (as required), complete all as specified and directed.

Supply and fixin repairs,LED mirror light fitting upto 10 Watt, wall mounted type with LED Lamp & all accessories, complete all as specified and directed.

Supply and fixing, company made sheet metal enclosure single pole & neutral with a two pin & earth plug and socket complete with one single pole 'B' series MCB 20 Amps 240 Volts, 10 KA, complete all as specified and directed.

Note:- Amount of credit of Rs. 87681 for retrieved materials is mentioned in Schedule of Credit Page No 128 & 129 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Vinod Kumar Aggarwal

M/S Punia Constructions