DEVELOPMENT OF RURAL CIRCUIT MALANAD MALABAR CRUISE TOURISM PROJECT PHASE II UNDER SWADESH DARSHAN SCHEME-Venice Floating Market at Valapattanam and Parassinikkadavu

Amount

Venice Floating Market at Valapattanam and Parassinikkadavu (2 Nos)

Supplying and Fixing HDPE floating platform by enveloping Single layer HDPE Universal cubesconfirm of ISO 9001 - 2008 including the cost of Galvanised Dipped structural frame and 3 mm tk Aluminium checker plate etc to complete as per the direction of Engineer in charge. Size of single Deck = 50 x 50 x 40 cm, Weight per Cube = 7 Kg, Load = 360 Kg/Sqm, Color = Grey, Blue, Black , Red or Green

Providing and Laying 3 mm tk Poly corbonate roofing sheet including the cost of Fiting Accessories etc to complete But Excluding the Frame Work. As per the direction of Engineer in charge

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. G.I. pipes ( Roof and Column Fabrication Work )

Providing and fixing Stainless Steel hand rail (Grade 316) railing made of hollow tubes, plates etc. Including welding, grinding, buffing with all accessories etc to complete as per the approval of Engineer in Charge

Installation of Vertical pole piling of 6 inch diameter, hot dipped galvanized M.S Poles at water bed with crane and help of Khalasi, where end of poles are prepared for piling and roller guide system of nylon rollers of adequate diameter mounted on SS angle sections are used etc to complete

6" Heavy duty 316 Stainless Steel Boat mooring bollards with Cleats

Mild Steel Hinged ramps for barrier free access to walkway (Size of Ramp is 6.00 x 3.00 m This is an approximate dimension. During the time of execution, size should vary as per actual site conditions.)

Outdoor curtains with scratch resistant PVC with margin grade SS runner to avoid wind lift of Curtains etc to complete

25.7 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Finishing with Marine Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Supplying and Fixing Pollord Garden Light including the cost of fitting Accessories but excluding the cost of Wiring,Electricity connection etc to complete as per the direction of Engineer in Charge

Disposal of Waste water, Internal Plumbing, Wash Basin etc to complete as per the direction of Engineer in Charge

Supplying and Erection of 7.5 KV DG Set including the cost of conveyance etc to complete as per the direction of engineer in charge

Electrification Work

Suplying and Fixing 100 litres capacity waste bin (Eco friendly)

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply and Fixing 9 litres Fire Bucket

Supply and Fixing 6 Kg Fire Extinguisher

Extra Fenders for Aviod crushing between boat and platform

EXCLUDING GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of installation, testing and commissioning cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD/Irrigation Dept. specification and direction of Engineer at site.

5.The Technical Specifications for the floating restaurant is enclosed herewith , reffered document No. KMPS/241/1003/508/2022 dated 11-05-2022

6.CEMENT: Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

7.RCC: (Assessment of strength of concrete by Cube testing at Approved Govt labs as per IS) Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

8.STEEL REINFORCEMENT: Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference

9.CENTERING & SHUTTERING: (Centering and shuttering for different category of work may be considered separately.)

10. STEEL WORK G.I.PIPE: Make: JINDAL, Tata or eq. primary make in the order of preference.

11.ALUMINIUM WORK: Make: INDAL, JINDAL or eq. in the order of preference and prior sample approval from KEL, Client

12.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

12.1 Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

13.PLUMBING & SANITARY FITTINGS: Note: Make of Water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

14. VETRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

15. STEEL WORK G.I.PIPE: Make: JINDAL, Tata or eq. primary make in the order of preference.

CUBIX INFRASTRUCTURES

AAYKAYCONSTRUCTIONS