CONSTRUCTION OF GOVERNMENT MEDICAL COLLEGE RUDRAPUR (DISTRICT-UDHAM SINGH NAGAR)

Amount

CIVIL WORKS Fertile topsoil to be stockpiled and reused Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, griders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, pillars, piers, abutments, posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings), except spiral staircase

Edges of slabs and breaks in floors and walls i) Under 20 cm wide

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). i) All works upto plinth level.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). ii) All works above plinth level upto floor V level.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC. Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases.: All works up to Plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC. Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases.: All works above plinth & up to floor V level.

Extra for R.C.C/ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Extra for providing richer mixes at all floor levels.: Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). Floor Joint of 200 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). Wall Joint of 200 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of 200 mm gap

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand)

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. i) Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory window s & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non tox ic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter jo ints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum f rame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge) , minimum compressive strength of 58 N/mm2, modulus of elast icity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fa steners of required dia and length complete as per direction of Engineer-In - Charge . (M.S hold fast/lugs or SS dash fasteners shall be paid for separate ly). Note: For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable . Variation in profile dimensions on plus side shall be acceptab le but no extra payment on this account shall be made Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium ca rbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/bore r proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S sc rews, all as per direction of Engineer-In­ Charge. (Not e : stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). i) Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete i) 100X58X1.90 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete i) 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete i) 300x10 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete. i)Twin rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.. Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Float glass panes 4 mm thick glass pane (weight not less than 10 kg per sqm)

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching beading

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-incharge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position andapplying a priming coat of approved steel primer using structural steel, etc. as required. In gratings, frames, guard bar, ladders, railings, brackts. Gates & similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. i)80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. i) Exceeding 10.00 sqm and upto 16.80 sqm in the area

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx3.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 3.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work).

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for pre finished nosing to treads of steps of marble/granite stone.

Extra for marble/granite stone flooring in treads of steps and risers using single length up to 2.00 metre.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified double charged floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Thickness of tile minimum 09mm. Size of Tile 600x600 mm

Providing and laying Vitrified double charged tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Thickness of tile minimum 09mm. Size of Tile 600x600 mm

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber join t tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

12 mm cement plaster : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

20 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

6 mm cement plaster : 1:3 (1 cement: 3 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying cement putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete.

White washing with lime to give an even shade : New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade i) New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with textured exterior paint of required shade i) New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade i) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. i) Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : a) For fixed portion i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. i) Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): i) With float glass panes of 5.50 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. i) With brass cover plate minimum 1.25 mm thickness.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. "(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. " "Note:-1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025." "1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr. 2. Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml"

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin-Charge.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Anti static flooring Providing & Fixing flexible PVC sheet flooring with having a total thickness of2mm and weight of 3kg/m².Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. PASTELL ESD shall conform to Group P of Wear Resistance as per EN 649, Flammability of class Bfl-s1 as per EN 13501-1, Slip resistance as per DIN 51130 group of R9 , having REACH Registration No, 1907/2006 contains no substance mentioned in SVHC list. Impact sound reduction of 3 dB as per ISO 140-8, Residual indentation of 0.05 mm as per EN 433, Color fastness rating ≥6 as per ISO 105-B02, Vertical resistance(R1) less than 1 x 10⁶- 1x 10⁸Ω as per EN 1081, and surface resistance less than 1 x 10⁶- 1x 10⁸ Electrical insulation to ground greater than 50 kΩ as per VDE 0100, Static electrical charge of ≤2.0kV as per EN 1815, Thermal resistance of 0.04m²K/W as per EN 12667, Thermal conductivity of 0.25 W/mKa Equivalent Installation: It is important to ensure the sub floor on which the sheet is being laid is smooth, flat & hard & free from moisture, grease, etc. In case of uneven sub floor the same should be leveled by self leveling compound. IPS/Vitrified/ceramic/mosaic tiles do not provide zero leveled sub floor.The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid each row of tiles/strip of floor covering must be linked crosswise with a continuous copper strip. Individual rows/strips must be at least 3 m² in size and linked to the rest of the area with a copper tape. In rooms of up to 40 m², connection points for equipotential bonding should be provided in at least one point in the room. In larger rooms, several connection points must be used. The installation shall be undertaken as per the manufacturer’s installation instructions complete to the entire satisfaction of Engineer-in-charge.

Providing and fixing Brand S.S. 316 Grade Mortice Handle Ø22mm with euro profile escutcheons [Finish : Satin] [Mechanically BSEN 1906 : 2010 Certified] AND Brand Lock Body - 9'' [With Stainless Steel main and strike plate] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Key & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Slot & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S. (Normal Grade) Tower Bolt [Flate] 300 mm [Finish : Satin] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S.316 Grade Door Stop [Finish : Satin] complete as direction of Engineer-in-charge.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 m Excavation for roadwork in soil with hydraulic excavator of 0.9 Cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3

Granular Sub-base with Well Graded Material (Table 400.1) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading I Material

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge. (CC 1:4:8)

Cement Concrete (PCC M-30) Pavement:- Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications.

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade ‘A’ sealing compound.

Providing and laying of hot applied thermoplastic compound of ISI Mark Approved Quality of 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes

kerb stone Plain/reinforced cement concrete in substructure complete as per drawings and technical Specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m) R.C.C. grade M 25

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge. Mandatory/ Reg`ulatory sign boards of 900 mm diametre with support length of 3750 mm

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge.: Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Supplying and filling of good earth at site including royalty, carriage and watering, rolling complete.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge.

Providing and Displaying plants Chrysenthemum single named variety in different colour well developed, having 45 to 60 cm ht., minimum 150 and above half bloom flowers well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 30 cm Earthen Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Salvia ht. 45 to 60 cm multi branches stacking with bamboo stick specimen plants type with full bloom well developed in 30 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Cockscomb well developed fresh & healthy 20 to 25 cm ht. attractive colours fully bloomed in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Sunflower single well developed 8 to 10 half bloom buds multi branched in fresh & healthy full stacked with green painted bamboo stick stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Topiary plant of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120- 130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Foxtail palm plant of ht. 240-270 cm bottom girth 35-40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Mangifera indica (Mango-grafted ) plant of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-incharge.

Supply and stacking of Plumeria alba plant of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Plumeria rubra plant of height 120-150 cm. with 3- 4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Polyalthia longifolia (Ashok) plant of height 150- 165 cm. in earthen pots of size 25 cm as per direction of the officer incharge.

Supply and stacking of plant Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge.

INTERNAL & EXTERNAL PLUMBING & SANITARY WORKS Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth White Agaria Marble Stone

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510X1040mm bowl depth 200mm.

Sink without drain board 610X510 mm bowl depth 200mm.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm

Providing and fixing toilet paper holder: C.P. brass

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in-charge

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge..(sink & urinal)

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore

Providing and fixing wash bashin with C.I. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required - a) White vitreous china wash basin size 550x400 mm with a 15 mm cp brass singal hole basin mixer.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge..

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete Flexible Pipe, 32mm Dia

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge . a) 15 mm nominal dia.

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet 100 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Supply, installation, testing and commissioning of AUTOMATIC soap dispenser holder with stainles steel lid and brackets fixed to wooden cleats with C.P. brass screws.

Supply, installation, testing and commissioning of ABS fully automatic "No Touch" hand drier suitable to operate on 220 volts, single phase 50 hz., A.C. power supply

Supply, installation, testing and commissioning of ABS fully automatic "No Touch" AUTOMATIC HAND SANITIZER suitable to operate on 220 volts, single phase 50 hz., A.C. power supply

Supply, installation, testing and commissioning of wall mounted 1 nos Stainless Steel Handicap DISABLED GRAB BAR (U SHAPE) - (SET OF 2)including cutting & making good the walls.

Supply, Installation, Testing and commissioning of wall hanging drinking online water cooler With cooling capacity of 60 LPH, with one drinking station and one swan neck tap for bottle filler , with MDCU29 Antimicrobial touch pad amd made by stainless steel top and heavy duty galvanized steel frame. With cooling capacity, ADA Compliant, size 472 mm Depth X 447mm width, flexible bubbler guard , Model- PG8AC ,operated between 50 to 120 PSI, Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply Complete with all accessories which include MD-CU29, which is an EPA registered antimicrobial copper that fights off microorganisms which include MRSA and e-coli. The water Fountain shall possess NSF-USA, Green building, energy star saving certification, and to be placed at different location of buidling. for proper functioning and aesthetic view as directed by the engineer-in-charge without any extra cost. Certified By NSF, GRIHA, TUV, UL, WATER QUALITY Asso.,UL, Stare rating Energy saver. Mechanical operation .

INTERNAL DRAINAGE INSTALLATIONS Providing and fixing cast iron trap of self cleansing design with cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 100 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing cast iron trap of self cleansing design with cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 75 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing soil, waste, vent and rain water pipes Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. 100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing plain bend of required degree. 100mm dia Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing single equal plain junction of required degree : 100X100X100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing single unequal plain junction of required degree 100x 100x75 mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing Hubless cast iron offsets epoxy coated inside & outside as per IS : 15905 130 mm offsets With 100 mm dia

Providing and fixing terminal guard: 100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100mm SS 304 grade coupling with EPDM rubber gasket

Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround CI HUBLESS including bed concrete as per standard design Note: This work shall be done all-round PIPE AT ground floor's toilet. 100mm diameter

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) 40 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) 50 mm dia, nominal bore

Providing and fixing of MS cap 100mm dia

Providing & fixing on wall face unplasticised -Rigid PVC rain water pipes conforming to IS:13592 Tyape A included jointing with seal ring conforning to IS:5382 leaving 10 mm gap for thermal expansion. (i)Single socketed pipes. 110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion. Coupler -110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion. Bend -87.5 deg -110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion. Shoe -110mm shoe

Providing & fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia

INTERNAL DRAINAGE WORK Providing and fixing Hubless centrifugally cast iron pipe (IS 15905) soil and waste water including all fittings (plain or door) e.g. bends, junctions, cowls, offsets, access pieces jointing with SS 304 grade coupling with EPDM rubber gasket including fixing the pipe on the wall/ceiling with suitable clamps ,holder bat clamps and anchor fastener of approved design to sand cast iron (spun) pipe embedded, cement concrete block 10x10x 10 cm of 1:2:4 ( 1 cement: 4 coarse sand: 4 graded stone aggregate 20 mm nominal size), cutting holes in wall and floors, excavation, refilling and disposal of surplus earth where required and marked good complete etc. and as per direction of Engineer in Charge. 150mm dia Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I. Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen complete in all respect. 100 mm diameter pipe (Hopper )

Providing and fixing F.R.P. Grating. With "L" angal 377 x 1006x30 mm ( Load Bearing capable 5.0 T, suitable for External drain Area ) Drain Cover

Providing and fixing F.R.P. Grating. With "L" angal 636 x 1006 x 30 mm ( Load Bearing capable 5.0 T, suitable for External drain Area ) - Drain Cover

WATER SUPPLY INSTALLATIONS Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 15 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 20 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 25 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 32 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 40 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 50 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge concealed work including cutting chases and making good the wall etc. 15 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge concealed work including cutting chases and making good the wall etc. 20 mm nominal outer dia pipes

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 25 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 32 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 40 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 50 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 65 mm dia, nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 80 mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 25mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 32 mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 40 mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 50 mm dia, nominal bore

Providing and fixing gun metal non- return valve of approved quality (PN 1.6) 40 nominal bore

Providing and fixing gun metal non- return valve of approved quality (PN 1.6) 50 nominal bore

Providing and fixing gun metal non- return valve of approved quality (PN 1.6) 80 nominal bore

Providing and fixing brass stop cock of approved quality 15mm nominal bore

Providing and fixing brass stop cock of approved quality 20mm nominal bore

Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 65 nominal bore

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 80 nominal bore

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 100 nominal bore

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on gyeser and solar water pipe suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm

Providing and fixing GI pipes medium class conferming to IS 1239 with GI fittings including cutting hole chase painted with primer, two coats of enamel paints etc 100 mm dia, NB

WATER SUPPLY- INTERNAL WORK Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). 15 mm dia nominal bore

Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). 20 mm dia nominal bore

Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). 25 mm dia nominal bore

Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in iverhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc. 50 mm dia NB Float Valve

HOT WATER AND RO WATER SUPPLY PIPE Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 15 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 22 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 28 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 35 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 42 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 54 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 76.1 mm nominal outer dia pipes

Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 88.9 mm nominal outer dia pipes

EXTERNAL SEWERAGE SYSTEM Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil up to 1.50 m depth Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. 150 mm diameter

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 250 mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 300 mm dia RCC pipe

Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level 1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size)

Constructing brick masonry manhole with F.P.S. bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole with F.P.S. bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manhole with F.P.S. bricks size 90 X 80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Size 120x90 cm

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG ) 180x150 mm size P type With FPS bricks

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 230mm dia.

EXTERNAL STORM DRAINAGE SYSTEM Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 150 mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 250 mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 300 mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 450 mm dia RCC pipe

Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level 1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:5 (1 cement : 5 fine sand) including 500 x 450 mm (heavy duty) precast RCC horizontal grating with frame complete as per standard design: with FPS bricks

Providing and laying in position cement concrete of specied grade excluding the cost of centering and shuttering (for filling of drain haunches) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

12 mm cement plaster of mix 1:6 (1 cement : 6 coarse sand).

Reinforced cement concrete work in RCC culvert slab with 1:1.5:3 (1 cement : 1.5 coarse sand and 3 gradded stone aggregate of 20 mm nominal size) excluding centering and shuttering and reinforcement.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand)

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450mm internal dimensions

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800(Part I ), including collecting sample from different strata , preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90m depth below ground level. All types of Soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. 150mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen(RMS) pipes with ribs, conforming to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5mm to 2mm, in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 100 mm dia

DISTRIBUTION NETWORK FOR FRESH WATER SUPPLY Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 25mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 40mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 50mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 65mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 80mm nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 25 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 50 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 65 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 80mm nominal bore

external works Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works 25mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works 50mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works 65mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works 80mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. 25mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. 50mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. 65mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. 80mm nominal bore

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 80 mm dia

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 100 mm dia

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 100 mm dia.pipe

Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: With F.P.S. bricks

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : iv) 32 mm nominal bore

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 M including getting out the excavated soil (HARD OR SOFT) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [hard/Dense soil] All kind of soil Pipes,cables etc.exceeding 80mm dia.but not exceeding 300mm dia.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m,but not exceeding 3 m.(Rate is over corresponding basic item for depth up to 1.5 metre).

Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing & fixing of Garden hydrant outlet consisting 1 No. 20mm dia. Ball valve, Bib cock (Brass) for connecting rubber hose, pipes & fittings including brick masonary chamber 300x300x500mm. Bib Cock - 20mm

Providing & fixing of Garden hydrant outlet consisting 1 No. 20mm dia. Ball valve, Bib cock (Brass) for connecting rubber hose, pipes & fittings including brick masonary chamber 300x300x500mm. Ball Valve - 20mm

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 65 nominal bore

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 80 nominal bore

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 100 nominal bore

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified. 100 nominal bore

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified. 80 nominal bore

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing GI pipes medium class conferming to IS 1239 with GI fittings including cutting hole chase painted with primer, two coats of enamel paints etc 100 mm dia, NB

(Pumps, ETP, STP, Electromechanical) WORKS Raw Water Treatment Feed Pump set Providing, fixing, commissioing and testing package vertical raw water pumps, comprising of Electrical Driven inline pumping with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure guage bourden type, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pumps shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C supply & shall be having the following requirement complete with foundation and associated civil works. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve Suction & delivery header including all pipes, suction & delivery sides valves, NRV, Pressure gauges & accessories complete. Flow Rate : 5.0 LPS (1 working + 1 stand by) Head : 35 M Min. Motor HP : 5.0 H.P. (Each)

Water Booster Pumpset (Treated Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 9.0 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps. Ball valve on suction & delivery

Sump Pumps Supply & Installation, testing and commissioning of centrifugal non clogging submersible sump pumps for plant room drainage. Pump capable capable of handling 25 mm dia soft solids. Motor suitable for 415 + 10% volts, 3 phase, 50 Hz AC Power supply. Pumps shall be suitable for automatic/manual operation (Overall depth of sump – 1.5 M). Submersible sump pump shall be provided with dry running protection. Inclusive of supporting arrangement for stationary type. Two nos. of pump installed in one sump pit 1 working & 1 standby with automatic/manual opration as requireds. Waste Water Drainage Sump Pump (PLANT ROOM ) Flow rate : 4.0 LPS Head : 10 Mtrs. Min. Motor HP : 1.5 (Each)

Supplying, storing, handling, installation, testing & commissioning of Vertical Dual Media Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole, initial filling of Graded sand and gravels, pressure gauges, sampling cock, air vent, frontal MS/UPVC Piping, diaphragam valves for inlet, outlet, backwash inlet, backwash outlet drain etc. Capacity : 5.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of Vertical Activated Carbon Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole initial filling of Activated Carbon, pressure gauges, sampling cock, air vent, frontal MS/UPVC piping, diapharagam valves for intlet, outlet, backwash inlet, backwash outlet drain etc. Capacity : 5.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of water softening system having MSEP/FRP pressure vessel suitable for test pressure of 7 Kg/cm2 including dished end, ion- exchange resin, Frontal piping, C.I. diaphragm type valve, brine injection assembly for regeneration of softener, brine measuring cum salt water tank, inter connected flexible polypropylene MS Rubber lined (MSRL) piping, valves including provision of bye-pass arrangement complete with inside and outside painting etc. as required. Receiving, storing, handling and fixing of PVC/HDPE/FRP tank for Brine solution along with Hydraulic Injector with control valve and piping for brine injection. Capacity : 5.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying and fixing of PVC/HDPE/FRP tank including electrical operated metering/dosing pump for dosing of alum/sodium hypo-chlorite solutions in pipeline (all contacting parts shall be of stainless steel). Capacity - 0-12 LPH

Supplying & fixing of float based visual flow meter (Rotameter) suitable for water flow rate of 18000 litres per hour in the input line of water softener including matching flanges, nuts, bolts and 3 mm thick rubber insertions/gaskets complete. to assess the water flow rate in water softener.

RO PLANT - For Academic Block Lab Area Supplying, installing, testing & commissioning of R.O. Plant including filters, pumps, dosing units, control panel, piping and valves and 1,000 litres SS 304 stainless steel tank complete as per specifcation and drawings. For Drinking Feed Flow - 1000 LPH Product Flow - 500 LPH Reject Flow - 500 LPH Recovery - 50% Mode of operation - Manual Operating Pressure - 10 to 12 Kg/cm2

POWER & CONTROL CABLING Supplying and Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with coke and salt ) as required.

Providing & fixing 25mm x 5mm G.I. strip on surface or in recess for connections etc. as required.

Providing and Fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, fabricating and installing following size of perforated M.S. cable trays, including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including paint 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying, fabricating and installing following size of perforated M.S. cable trays, including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including paint 300 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size not exceeding 25 sqmm on surface as required.

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size exceeding 25 sqmm but not exceeding 120 sqmm on surface as required.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 120 sq. mm. Armoured Aluminium cable.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 35 sq. mm. Armoured Aluminium cable.

Control Cabling ( PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays). 5C x 1.5 Sq. mm

SBR Based Plant Semi-Automatic System Supplying, installation, testing & commissioning of Sewage Treatment Plant for the following duty: Nature of waste water - Sewage + effluent Daily average flow - 75 + 10 cum/day Influent Characteristics pH - 8 BOD5 - 250- 300 mg/liter S. Solids - 250 mg/liter COD - 400-600 mg/liter Oil & Grease ` - <50 mg/liter Effluent discharge standard : pH - 6.5-8.0 BOD5 - Less than 10 mg/liter & < 5 after GRA-UOT S. Solids - Less than 10 mg/liter COD - Less than 50 mg/liter Oil & Grease - < 5 mg/lt Reuse of STP treated water after treatment. Horticulture, Landscaping, irrigation, flushing etc. NOTE (1) All Civil works finished with water proofing, plaster, snowcem, structure duly tested for leak-proofing, plant room flooring etc and related S.S/MS/CI works such as supply and fixing of handrails, manholes, gratings, grills, doors, vents, footrests etc shall be in the scope of the STP Client. Supply and fixing of puddle flanges will in the scope of Civil Contractor/ Client. (2) Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete automatic working of the STP and have it approved by the Owner / Consultants. Part (A) ETP Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Raw sewage Transfer pumps with suitable solid handling capacity with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty: Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 4.5 m³/hr Head = 8-10 m

Dosing System for Physico-chemical treatment Alum dosing system Lime dosing system Poly dosing system

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1 m³/hr Head = 8-10 m STP .

Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Submersible pumps with solid handling capacity upto 30 - 40 mm with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty:Pumps = 02 Nos.(1w +1s) Flow rate (each) = 8.5 m³/hr Head = 8-10 m

Providing and fixing all interconnecting exposed plant piping of required MOC as MS/GI/PVC/CPVC/UPVC and isolation control valves for making the piping arrangement complete within the battery limits.

Supply, installation, testing & commissioning of SBR Based Biological system comprising of the following equipments:Air Blowers For SBR tanks Capacity : 50-150 m3/hr @ 5000-5500 mmwg Type Twin Lobe Qty -2 Nos. (1 w+1s) Disc type Fine Bubble Diffusers Size: 300 mm Dia Decanter system Qty -1 Nos. Type : Moving/Floating MOC : SS-304 Pipes and fittings for Air piping and Air Grid Qty-1 Lot Level transmitter/controller and accessories Qty-1 Lot PLC for SBR system Qty -1 Set

Supplying, installing, testing, commissioning of Centrifugal Horizontal Filter Feed pumps Complete in CI body& CI impeller with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 7.5 m³/hr Head = 25 - 30 m

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1-2 m³/hr Head = 8-10 m

Supply, installation, testing & commissioning of Sludge feed pumps for sludge Feeding to sludge bag system complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 0.5-1 m³/hr Head = 25-30 m

Supplying, Installation, testing and commissioning of Chemical dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump for dosing.

Supplying, installing, testing, commissioning of Filter Press of suitable size for the dewatering of sludge generated per day.

Mode of operation: Manual Supplying, installation, testing & commissioning of MSEP/FRP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain.Multigrade Sand Filter Dia : 1100 mm HOS: 1800 mm

Filter media: Fine and coarse sand, pebbles and gravels Activated Carbon Filter Dia : 1100 mm HOS: 1800 mm Filter media: Activated Carbon, fine and coarse sand, pebbles and gravels

Water Booster Pumpset (Flushing / Soft Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below.Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 6.0 LPS to a head to 70 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Providing, fixing, testing and commissioning of horizontal centrifugal Irrigation water transfer pumps. The pumps shall be made of C.I. casing, CI impeller, SS shaft & sleeve. Mechanical seal connected by to a TEFC induction motor mounted on a common channel base-plate with efficiency class IE3 or EFF-1 whichever is more efficient with coupling guard 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator, pads of approved design. Motor to be suitable for 400/440V, 3 phase 50 cycles AC power supply, including all necessary piping, suction and delivery header, individual suction and delivery of pump, valves, NRV, pressure gauge and other accessories and concrete foundation complete as required. Irrigation pumps: Capacity : 5 LPS Head : 50 Mtrs Type of Pump : Horizonal Centrifugal pump No. of Pumps (2 Nos. – 1 W + 1 S)

FIRE-FIGHTING WORKS FIRE PUMPS - ELECTRICAL Supply, installation, testing and commissioning of horizontal single stage centrifugal type factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP-55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles AC. Capacity 2280 LPM at 7.0 Kg/cm2 delivery pressure for Fire Hydrant Network.

FIRE-FIGHTING WORKS FIRE PUMPS - ELECTRICAL Supply, installation, testing and commissioning of horizontal single stage centrifugal type factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP-55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles ACCapacity 180 LPM at 7.0 Kg/cm2 (Jockey Pump).

"FIRE PUMPS - DIESEL Supply, installation, testing and commissioning of horizontal single stage centrifugal pumping set with CI volute and bronze impeller with mechanical seals directly coupled to automatic Diesel Engine complete with all accessories like self starting by means of Battery powered electric starter motor, Paper Filter type air cleaner, exhaust silencer etc. complete in all respects. The engine & the pump will be mounted on common base plate on anti-vibration mountings." Capacity 2280 LPM at 7.0 Kg/cm2 delivery pressure for Fire Hydrant & Sprinkler Network.

Electric Motor Driven Hose Reel Pump (Location - Roof )Supplying, installing, testing and commissioning of Fire authority approved Electrical driven fire pump suitable for automatic/ manual operation consisting of the following: Horizontal mounted split casing type fire pump having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 900 LPM against a total head of 35 M while running at 1400 RPM complete with mechanical seal pressure gauge with GM cock on the delivery side of pump and including 50 mm by pass arrangement (with 50 mm valve and up to 5 meter GI class 'B' pipe) for periodical testing of working of pumping test. Squirrel cage, induction motor TEFC type suitable for 415 + 10%V, 1 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of 1400 RPM with flexible coupling and coupling guard . Common bed plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with heavy duty Anti Vibration pads (4 Nos., heavy duty). Coupling and coupling guard for direct coupling of pump and motor. Drain Pipe with Valve (50 mm dia) Hose Reel Pump Discharge : 900 LPM App. Head : 35 m App. HP : 15.0

PANELS: Supply, installation, testing and commissioning of followingintegrated, cubicle type,dead front, extensible, sheet steel control panel. The panel shall be suitable for 440 volts, 50 cycles, 4 wire supply The following components and accessories shall be mounted with ineach control panel. One no 100 amps TP incoming MCCB with the following: 0-500 volts 96 x96 square mm voltmeter with slector switch and control fuses- 1 SET 0-100 amps 96 x96 square mm ammeter with CT's and slector switch- 1 SET Phase indicating lamp with toggle switches. Indication lamps for ON/OFF/TRIP status Outgoing Feeders / Starters as below: 100 ATP MCCB with star / delta as starter suitable for 30 HP motor for Downcomer Pump - 1 Set Provision in control panel to connect flow switch for autmatic operation of roof fire pumps. Discharge : 450 LPM App. Head : 35 m App. HP : 15.0 PANELS: Supply, installation, testing and commissioning of followingintegrated, cubicle type,dead front, extensible, sheet steel control panel. The panel shall be suitable for 440 volts, 50 cycles, 4 wire supply The following components and accessories shall be mounted with ineach control panel. One no 100 amps TP incoming MCCB with the following: 0-500 volts 96 x96 square mm voltmeter with slector switch and control fuses- 1 SET 0-100 amps 96 x96 square mm ammeter with CT's and slector switch- 1 SET Phase indicating lamp with toggle switches. Indication lamps for ON/OFF/TRIP status Outgoing Feeders / Starters as below: 100 ATP MCCB with star / delta as starter suitable for 30 HP motor for Downcomer Pump - 1 Set Provision in control panel to connect flow switch for autmatic operation of roof fire pumps.

Exhaust piping Providing & fixing 150 mm diameter M.S. Class 'C' diesel pump exhaust pipe includings all fittings, like bends, tees etc. clamps / structural steel supports. The pipe shall be provided with 75mm thick fiberglass insulation & covering the insulation with 500 g polythene sheet giving proper overlaps & sealing the joints with suitable adhesive compound. The pipe shall be provided with 24 gauge aluminium sheet cladding

PRESSURE SWITCH Supplying, installing, testing and commissioning 0 to 12 Kg/ cm2 ON/OFF pressure switch in delivery line of pump along with control wiring for auto starting and auto stopping of hydrant and jockey pumps.

Supply, fabrication (as per code), installation, testing and commissioning of Air vessels 250mm diameter and 1200mm high fabricated from 8mm M.S. plate with accessories inside painting with epoxy paint and outside with enamel.

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.8 Kg/cm2 and test pressure 14 Kg/cm2 for :- 150 mm dia

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.8 Kg/cm2 and test pressure 14 Kg/cm2 for :- 100 mm dia

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.8 Kg/cm2 and test pressure 14 Kg/cm2 for :- 80 mm dia

Supply, installation, testing, trial run and commissioning of hydrants all complete as required and as approved Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 900x600x2100 Recessed type mansoary box (by civil contractor).

Providing and fixing of TAC approved 1.6mm thick M.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant.

Providing and fixing of 63mm dia single outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

Providing and fixing of 63mm dia twin outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

Providing and fixing of First aid hose reel with 25 mm dia, 30 m long rubber hose, ball valve, piping and GM nozzle

Providing and fixing of 63mm reinforced rubber hoses (RRL) with male and female GM coupling, IS marked- 15 m long

Providing and fixing of standard short size GM branch pipe with nozzle of 20mm nomnal bor outlet with instaneous type 63 mm dia coupling complete IS marked & TAC approved.

Providing and fixing Fire Axe

Providing and fixing of ss orifice plates in pipelines to reduce pressure from 8 kg. to 3.5 kg/sq.cm.

Providing, installing, testing & commisioning of fire brigade inlet connection (fire department connection) consisting of 4 Nos. 63 mm dia instantaneous inlet arranged on a 50 mm dia header, 1 No. 150 mm diameter Butterfly valve, 1 No. 150mm dia. Non-return valve and wall mounted box of M.S. construction with glass door to house the above mentioned components.

Providing, installing, testing & commisioning of fire brigade draw out connection (fire department connection) with suction pipe MS class 'C' 100 mm dia. & 100 mm dia. foot valve & steel chain including wall mounted box M.S. construction with glass door to house the above mentioned componenets.

PIPING FOR FIRE FIGHTING SYSTEM Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Constructing masonary chamber 90 x 90 x100 cm. inside with 75 class designation brickwork in cement mortar 1:5 ( 1 cement : 5 fine sand) for sluice valve with CI surface box 100 mm top dia. 180 mm bottom dia. And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and inside plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with FPS bricks

Providing and fixing C.I. double acting air valves of approved quality with bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if reqd. will be paid separately) 50 mm dia.

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 150 mm dia.pipe Class II

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 150 mm dia.

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as 80 mm dia

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as 100 mm dia

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 80 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 100 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 200 mm dia

Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required

Providing laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 1239/3589 (all pipes shall be ISI marked and of makes specified in the specifications) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including excavation & providing cement concrete blocks as supports and anti-corrosive treatment to burried pipes by wrapping & coating with 4 mm thk. (OR 2 COATS of 4.0mm thick tape) anticorrosion tape along with two coat of black japan primer for under-ground pipe . 150 nominal bore (class C)

Providing laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 1239/3589 (all pipes shall be ISI marked and of makes specified in the specifications) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including excavation & providing cement concrete blocks as supports and anti-corrosive treatment to burried pipes by wrapping & coating with 4 mm thk. (OR 2 COATS of 4.0mm thick tape) anticorrosion tape along with two coat of black japan primer for under-ground pipe . 100 nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 250 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 200 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 150 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 100 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 80 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 65 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 50 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 40 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 32 mm nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Note: Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 25 mm nominal bore (class C)

Supply, installation, testing and commissioning of 150 mm dia Installation Control Valve inclusive of 2 nos 150 mm dia Butterfly Valve, strainer, Alarm Valve with Water Motor Gong, Pressure Gauges, Test Lines with Ball Valves with necessary GI (H) piping with threaded fittings of required sizes complete

Supply, installation, testing and commissioning of 150 mm dia Zonal Control Valve inclusive of 1 nos 150 mm dia butterfly valve, 150mm diam. non return valve, Flow Switch, water pressure gauges & 25 mm dia. Auxillary Drain valve with sight glass with necessary GI (H) piping with threaded fittings of required sizes complete 150 mm dia butterfly valve 150mm diam. non return valve Flow switches in 150 mm. dia M.S. Pipe pressure gauges Pressure gauges in the M.S. Pipe Line including connection etc. as required. 25 mm dia. Auxillary Drain valve Sight glass

Providing, fixing, testing and commissioning of quick response 15 mm dia. gunmetal quartz bulb type sprinkler head to operate at 68 degree centigrade Pendent /Upright type

Supply, installation testing & commissioning Foot Valve lift type as per specifications to the satisfaction of Project-in-charge

FIRE EXTINGUSHER Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. Capacity 4.5 kg

Providing and fixing (ABC Dry Chemical Powder ) type Fire Extinguisher of Capacity 6 kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket complete with internal charges. Capacity 6 Kg.

Providing and fixing mechanical foam type Trolley Mounted Fire Extinguisher of bearing to IS:10568/IS13385/IS13386 with dis Capacity 45 Lit.

Providing and fixing Carbon Dioxide Type Trolley Mounted Fire Extinguisher of as per IS: 2878 with discharge time of 10 to 20 sec/15 to 36sec/20 to 60sec respectively. 22.5 Kg. CO2 Fire Extinguisher

FIRE WORKS Supplying and Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with charcoal/ coke and salt as required.

Supplying and laying 25 mm x 5 mm. G.I. strip in 40 mm dia. G.I. Pipe from earth electrode, including connection with GI nut, bolt, spring, washer excavation and re-filling etc as required.

Supplying, fabricating and installing following size of perforated painted with powder coating M.S. cable trays,with perforation not more than 17.5%, in covenient section, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying, fabricating and installing following size of perforated painted with powder coating M.S. cable trays,with perforation not more than 17.5%, in covenient section, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size not exceeding 35 sqmm on surface as required.

Aboved 35 sq mm and upto 95 sq mm (clamed with 25x3mm MS flat clam)

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 120 sq. mm. Armoured Aluminium cable.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 35 sq. mm. Armoured Aluminium cable.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 16 sq. mm. Armoured Aluminium cable.

Control Cabling (PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays). 5C x 1.5 Sq. mm

"FIRE ALARM & PUBLIC ADDRESS SYSTEMFire Panel & Annunciators Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be complete with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. Designed to meet UL864, 10th Edition" 10-loop - With Digital Voice Command Center

Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be complete with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. Designed to meet UL864, 10th Edition 2-loop - With Digital Voice Command Center

Network Repeater Panel with minimum 8" Color Touch Screen display with onboard Keypad for programming, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network, shall display the information of all the panels connected with the NRP and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation.

Digital Audio Amplifier shall be dual channel capable of processing Two of 8 audio channels and total of 100 W at 70.7 VRMS output along with necessary enclosures. The Digital Audio Amplifier shall be fully monitored for fault and alarm reporting. The proposed Digital Audio Amplifiers shall (be Wall/Panel Mounted) not be rail mounted / dependant on Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of Amplifier operation.

Addressable Rate of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing.

Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing. Designed to meet UL268, 7th Edition

Addressable Fixed high temperature Heat Detector rated at 88 deg C. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing.

Addressable Duct Smoke Detector. The duct detector shall have an air velocity rating from 100 to 4000 ft/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing.

Addressable High Sensitivity Photo Detector with sensitivity level of 0.02% to 2% Obs/Feet. The detector shall have the optic block to amplify signals from smoke, but diminish stray internal reflections that can cause false alarms. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing. Designed to meet UL268, 7th Edition

Addressable Beam Detector with transmitter & reciver, Addressing shall be inbuilt within detectoralong with all accessories.

Modules Addressable Manual Call Point ( Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device.

Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be inbuilt within each detector & wuld not require another propriatory machine for addressing. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Notification Devices Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

2W Multi-Tap (0.25W; 0.5W; 1W; 2W), Ceiling Mount Speakers. The speakers shall be of same make as that of the Control Panel & Amplifiers. They shall be compatible with supplied Amplifiers and shall work on 70.7Vrms. UL Listed

Addressable Power Supply Unit: 24V DC for Notification Appliances. The PSU shall be UL Listed, supervised by Fire Panel & of the same make as Fire Alarm System

Telephone Talkback Addressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center. UL Listed

Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center

Cables & Conduits Supply and Fixing of 25 mm dia MS Conduit

Supply and drawing of 2 C X 1.5 Sq mm multi stranded twisted unshielded FRLS Copper cable in the existing surface / recessed steel/ pvc conduit

Supply and drawing of 2 C X 1.5 Sq mm multi stranded twisted unshielded FRLS Copper cable in the existing surface / recessed steel/ pvc conduit

Software & Gateways Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

MODbus Interface Gateway for communication with BMS / Other Utilities. MODbus shall support minimum 12000 data points. MODbus Gateway shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of MODbus Gateway.

MGPS (MEDICAL GAS PIPELINE SYSTEM) OXYGEN SYSTEM Manifold : 08 + 08 size Oxygen manifold complete with NRV, Tail pipe

Fully Automatic Oxygen Contral Panel with Audio- Visual Alarm (MICROPROCESSOR Based)

02 + 02 cylinder Emergency Oxygen manifold complete with NRV, Tail pipe

High Pressure Regulator (14 No.) for Emergency Maniflod

Medical BS/Amico/Parkodex type oxygen gas outlet point with Probe

Oxygen flow meters with humidifier bottle

NITROUS OXIDE SYSTEM Manifold : 01 + 01 size Nitrous Oxide manifold complete with, NRV and tailpipe

Medical Nitrous regulator single stage and double gauge

Manifold : 01 size Nitrous Oxide manifold complete with, NRV and tailpipe

Medical BS/Amico/Parkodex type Nitrous gas outlet point with Probe

VACUUM SYSTEM Duplex Vacuum System (Vacuum Pump 5-HP with Electric Motor

Vacuum Reciver Tank 1000 Ltr with Vacuum Gauge and NRV with Brass fitting, Interconnecting brass fitting

Vacuum Bacteria Filter

Medical BS/Amico/Parkodex type Vacuum gas outlet point with Probe

Ward Vacuum Unit with Regulator, Collection Jar of 600 ml with Bracket

Suction Trolly With Regulator & 2000 Ml 2 Jar

COMPRESSED AIR SYSTEM Duplex Oil free Compressed with 7.5 HP Electrical Motor

Air Receiver Tank 1000Ltr. With all accessories

3- stage filtration system (P,Qand Y)

Air Dryer 45 CFM

Air Reducing Station

Medical BS/Amico/Parkodex type Air 4 Bar gas outlet point with Probe

Medical BS/Amico/Parkodex type Air 7 Bar gas outlet point with Probe

MISCELLANEOUS ITEMS Combined Electrical Control Panel for Vacuum and Compressed Air System with single phase preventer ans time totaliser

"Copper Pipe Lloyed certified as per BSEN 13348 Medical Grade"42 mm OD x 1.2 mm thick

"Copper Pipe Lloyed certified as per BSEN 13348 Medical Grade" 28 mm OD x 0.9 mm thick

"Copper Pipe Lloyed certified as per BSEN 13348 Medical Grade" 22 mm OD x 0.9 mm thick

"Copper Pipe Lloyed certified as per BSEN 13348 Medical Grade" 15 mm OD x 0.9 mm thick

"Copper Pipe Lloyed certified as per BSEN 13348 Medical Grade" 12 mm OD x 0.7 mm thick

"Medical Gas Alarm System (Digital) ( With NIST inlet connection)" 1 Gases + 1 vacuum

"Medical Gas Alarm System (Digital) ( With NIST inlet connection)" 2 Gases + 1 vacuum

"Medical Gas Alarm System (Digital) ( With NIST inlet connection)" 4 Gases + 1 vacuum

Zonnal Valve Box with Valves 5 Services

Zonnal Valve Box with Valves 3 Services

Zonnal Valve Box with Valves 2 Services

"ISOLATION VALVE ( Certified as Medical Oxygen Use)" 42 mm

"ISOLATION VALVE ( Certified as Medical Oxygen Use)" 28mm

"ISOLATION VALVE ( Certified as Medical Oxygen Use)" 22mm

"ISOLATION VALVE ( Certified as Medical Oxygen Use)"15mm

"ISOLATION VALVE ( Certified as Medical Oxygen Use)" 12mm

Bed Head Panel (Horizontal ) 3 Feet with Provision of gas outlet and Electrical point

Bed Head Panel (Horizontal ) 4 Feet with Provision of gas outlet and Electrical point

Bed Head Panel (Horizontal ) 6 Feet with Provision of gas outlet and Electrical point

MOT (MODULAR OPERATION THEATER) Walls and Ceiling puff panel:- Supply, Installation, Testing and Commissioning of Pre Fabricated Modular Operation Theatre. The free standing structure with insulated steel wall & ceiling puff panels. These panels are produced in a double band laminator, in which two continuously moving belts that is G.I. sheets of 0.80 mm are firmly bonded together by the sprayed-in insulating foam, which harden during this process. The density of puff is 40kg/m3 .The total thickness of panel is 50 mm.

Epoxy Filler& Anti-Bacterial Paint:- Filling all joints and cavities with epoxy filler and sanded flush to provide a seamless finish with antibacterial putty and paint.

Antistatic Vinyl Flooring:- Supply and Installation of seamless conductive flooring System, 2mm thick, having ESD / EMI (conductive) protection characteristics with perfectly cureved flush covings, all joints welded properly.

Self Leveling Compound:-Supply and Installation of Cement-based self levelling with Primer in average thickness of 3mm as per Endura/Indiana Specification

Planair Ceiling system / Laminar Flow :- Supply, Installation , Testing and Commissioning of Planair Ceiling system with unidirectional airflow. Plenum unit, holding structure & Top plenum are made of Aluminum Sheet 1.6mm thick with aluminum extrusion frame & sealed gasket conforming to DIN 4799 standards for the air distribution system with hepa filter having efficiency 99.97% down to 0.3 micron. The laminar flow system shall have such design that it provides "S" class Hepa filter. The filters will be placed terminally. The filter housing terminals are made of a one piece frame and plenum with perfect tightness features. SS-304 Diffuser: 2 layers of sufficient resistance to create laminar air flow from diffuser. Size-2400X2400X350 mm

Peripheral LED lights (285*585 mm):- Supply, Installation, Testing & Commissioning of Recess mounted IP54 protocol, non-hygroscopic Peripheral Lights for clean room application each set having compact fluorescent lamps and digital dimmable ballast.

Electric Wiring in Side OT (FRLS Wire) :- Supply, Installation , Testing and Commissioning of FRLS standard electrical wiring inside of operation theater including with switch/socket.

Pressure Relief Dampers:- Supply, Installation , Testing and Commissioning of proper Pressure Relief Dampers having multi 304 graded stainless steel blades for maintaining the positive pressure inside the operation theatre.

Membrane Type Control Panel:- Supply, Installation, Testing and Commissioning of membrane type Operation Theatre Control Panel (6 service Tiles) mounted flush in the theatre wall with all accessories etc. The control panel comprising of the following:- - 1 no Day Time Digital Clock - 1 no Elapsed Time Digital Clock - 1 no Hands Free Telephone - Medical Gas Alarm (5 gas) - Temperature & Humidity display - Peripheral Light Control

Electrical Distribution Panel Board

X-Ray Viewing Screen Twin plated:- CE compliance under the Directive of Operation Theater X-ray View Panel, Class 1 Medical Devices. The operation theater is equipped with twin plate X-ray viewer screens, which is designed to provide a high degree of control without flicker.

List Board :- Providing, Fixing, Supply & Installation Operating writing List Board of size 948mm x 648mm complete with all accessories.

Single Arm Anesthesia Pendant: Supply & Installation of Single Arm Pendant with following features: • 2 Equipment / Monitor shelves, • 6 nos. of 3pin universal electrical sockets-220V, 16A, • Provision of 6 nos. medical gas outlets, • 1 no. poles for infusion pumps and infusion sets, Arm Specification: • Ceiling Mounted, • 1000 mm, • Aluminum Alloy Powder Coated Construction, • Loading Capability ≥ 90 Kgs., • Rotation on every Joint ≥340 Degrees.

Double Arm Pendant: Supply & Installation of Double Arm Pendant with following features: • 2 Equipment shelves, • 6 nos. of 3pin universal electrical sockets-220V, 16A, • Provision of 6 nos. medical gas outlets, • 1 no. poles for infusion pumps and infusion sets, Arm Specification: • Ceiling Mounted, • 800 + 800 mm, • Aluminum Alloy Powder Coated Construction, • Loading Capability ≥ 90 Kgs., • Rotation on every Joint ≥340 Degrees.

Hermetically sealed Manual Sliding Door : Single leaf manual hermetic sealed sliding door 60 mm thick door blade with 52 mm PUF & HPL Sheet size W= 1800,H= 2100, Vision Glass (300mm x 300mm)

Hatch/Pass Box: Supply, Installation , Testing and Commissioning of Hatch Box. Made out of SS-304, for passing of linen/material. Each Hatch will be operated electronically. The Hatch will be design in such a way that only one door will be opened at one time.(Automatic)

Storage Units :- Providing, Fixing, Supply & Installation of storage unit size (1665mm x 865mm x 350mm) made of 1.5mm EGP 120 GSM Zinc coated complete with all accessories.

Air Handling Unit & Aluminium Ducting & Condencing Unit : Supply, Installation , Testing and Commissioning of floor mounted double skin air handling unit constructed out of 24 gauge GI pre-coated sheet as outer skin and plain 24 gauge GI sheet as inner skin with 40mm thick PUFF section in between and comprising of following sections. 1. Pre-filter section with 10 micron filters. 2. Cooling/ Heading section with dual circuit 6 row DX cooling coil 3. Blower section with backward DIDW blower, Drive set & pulleys 4. Fine filter section 5 micron filters at discharge side Other accessories like mixing box with fresh air moddle and return air damper, humidity controller, Common base frame with vibration isolation pads, suitable inspection doors for filters, coil & blower sections are provide. Capacity 3000CFM@ 125mm WG SP 5.5TR x2 =11TR minimum 30 air changes. ((Make-{AHU: Zeco ,wave aircon or Equivalent } {Condensing Unit:Carrier,Hitachi,Voltas or equivalent}) Note :- complete package with 22 gauge aluminum ducting and all accessories e.g L&T Schnider and minilec make electrical components used in distribution panel and as directed by the engineer in charge including carriage of materials in all leads and lifts.

RENOVATION WORK FOR EXISTING HOSPITAL BUILDING Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory window s & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non tox ic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter jo ints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum f rame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge) , minimum compressive strength of 58 N/mm2, modulus of elast icity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fa steners of required dia and length complete as per direction of Engineer-In - Charge . (M.S hold fast/lugs or SS dash fasteners shall be paid for separate ly). Note: For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable . Variation in profile dimensions on plus side shall be acceptab le but no extra payment on this account shall be made" Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium ca rbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/bore r proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S sc rews, all as per direction of Engineer-In­ Charge. (Not e : stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Providing and fixing Brand S.S. 316 Grade Mortice Handle Ø22mm with euro profile escutcheons [Finish : Satin] [Mechanically BSEN 1906 : 2010 Certified] AND Brand Lock Body - 9'' [With Stainless Steel main and strike plate] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Key & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Slot & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S. (Normal Grade) Tower Bolt [Flate] 300 mm [Finish : Satin] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S.316 Grade Door Stop [Finish : Satin] complete as direction of Engineer-in-charge.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm

Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge.

Dismantling of road gully chamber of various sizes including C.I. grating with frame including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead including refilling the excavated gap.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

2 cm premix carpet surfacing with 1.8 cum and 0.90 cum of stone chippings of 13.2 mm size and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). With paving Asphalt grade VG - 30 with no solvent

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. On bituminous surface @ 0.25kg/sqm

Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete.

Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern

TUBEWELL (2nos) & RAIN WATER HARVESTING PIT (10 nos) Construction of modular type rain water harvesting pit 32 cum. (For Recharge purpose) including following items. Drilling of bore well: (90 metre) Injection well insertion Upvc pipe 6'' diameter having a load capacity of 6kg/sqm Injection well insertion slotted pipes for clog resistent of rain water and reducing possibility of carrying soild. Solvent & screws for joing pipes with each other also for joinig end caps and bell plugs for bore. Clamps for keeping the pipe safe and holding the pipe while to ground level. Bell plug - supplying and fixing of bell plug with each bore well. End caps - supplying and fixing of end caps at the top of each bore well. Supply of bentonite fore bore wells drilling in order to give support and prevent from collapsing. Gravel filling for packing of empty space in the bore and to provide stability to the inserted pipes. Compressor/Boki cleaning- Earth work excavation with JCB/excavators in all types of soil/Ordinary rock/Hard rock and with a lift up to 5 meter. Material for base work (gravel/ston chips and double washed river sand) Dressing Compaction - of base soil Soil disposal - disposal of extracted soil from the site to inside the boundary walls of the building up to a maximumdistance of 0.5km Geo textile - to avoid invasion of soil provide stability to the tank and improve quality of water within the tank with tensile strength. Modular RWH modules material (685x410x408 mm) Backfilling of the area constructed in and around after compacting them properly. FRP Micro filter capable of removing soilds. Riser for filter extension.

Construction of brick masonry Desilting chamber of size 200x150x20cm Effective depth before rainy well with precast concrete block in cement mortar 1:4 (1 cement : 4 coarse sand) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand; 8 graded stone aggregate 40mm nominal size), inside and outside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement inside and rough plaster on outside, including fixing of grating , neatly finished with 2 nos.manhole cover complete in all respects including necessary excavation, refilling and disposal of surplus earth, complete as per approved drawing. .

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C.pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete (For Road Crossing) 450mm dia RCC Pipe

BOREWELL (2 NOS.) Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, up to 90 metre depth below ground level. All Types of Soil 350mm dia

Providing & fixing 200 mm dia. uPVC housing pipe 8Kg/Cm sq confirming to IS 12818 complete as per direction of engineers charges.

Providing & fixing 200 mm dia. uPVC Slotted pipe 8Kg/Cm sq confirming to IS 12818omplete as per direction of engineers charges.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing 200 mm dia. screw cap made out of PVC plate of sound construction locking arrangement. 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Supplying and fixing 80 mm dia. pipe class B ISI marked ncluding all accessories and fittings required for installation of pump.

Supplying & installation submersible pumping motor pumpsets ISI marked of approved make Kirloskar, KSB, etc., equivalent, making connection suitable for tube-well/D.C.B. The job includes screwing and welding of flanges on G.I. riser pipes (65 mm dia minimum) installation, complete fittings accessories with riser pipes jointing of electrical cables other connections making switch board electrical connections, all labour for testing of submersible pump and supply of water to water mains complete in all respects, 7.5 H.P app. motor having discharging capacity 12 to 15 cum/hour against a head of 120 metres.

"SIGNAGES WORK Building Branding Signage is made of 3D channel Latter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using L&T/Havells/schneider timer of required capacity. BRAND/MAKE- 247SIGN/ ASB Ads/ Vista (ENGLIS AND HINDI), Size- 30096 x 1200mm

SIGNAGES WORK Building Branding Signage is made of 3D channel Latter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using L&T/Havells/schneider timer of required capacity. BRAND/MAKE- 247SIGN/ ASB Ads/ Vista BLOCK NAME, size- 9120 x 900mm

" Totem A) INTERNAL Frame – Fabricated out of 100mm ISMC with Cross Supports and frame for Alloy made of 50 x 50 x 2 mm MS SHS . Structure shall be duly surface treated with primer & 2 coats of enamel Paint. B)Corner Profiles - Made of 75 x 19 mm Extruded 6063 alloy of minimum 2mm wall thickness with anodising in Dark color of brand 247Sign/ Vista/ Cosign C) Front and Back - ACP of approved color 4 mm thick having .5mm aluminium foil on boths sides , duly housed in the corner profiles. Text & pictographs CNC cut in the ACP D) Logo + Text : 3d Letters with translucent vinyl of MAKE 3M/LG/AVERY on 10 mm acrylic, 5mm inside and 5 mm ourside of ACP. E) Sides:- Sides of the totem 300 mm width to have white / approved colour illumination flowing. F) Illumination : The Lighting for totem shall be achieved through OSRAM make LEDS and IP 67 Grade powersupply. (G) Base Plate : Base Plate of size 400x400 mm twin plates of thickness 10 mm is to be used. BRAND /MAKE- 247SIGN/ COSIGN / VISTA System." Directional Totem, size- 900 x 2400mm

"Traffic regulatory A)POST :- Signage is to be made oF 100x100 mm 1800 mm High MS pole, Base Plate of size 250x250mm of thickness 10mm is to be used. Duly powder coated 50 microns in the desired colour. B) Panel-1 :- Panel size 400X110X1200 mm is to be made of 50x50x2 mm internal MS frame duly powder coated to 40-50 microns with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY Prismatic Retro reflective sheet and approved color Overlay film on top having desired text and pictographs on both side post. C) Panel-2 :- Panel size 600X600 Sq/round with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY Prismatic Retro reflective sheet and approved color Overlay film on top having desired text and pictographs. BRAND /MAKE of modular alloy:- 247SIGN/ COSIGN/ VISTA " Drop off/ Speed Limit / No Horn/ BASEMENT Entry/Exit, size- 450 x 1500mm

Entry/ Exit Signage Signage is to be made of Acrylic 4mm thick Box with translucent vinyl pasting on it. Illuminated with led Light (Four Sided) Mounted on S.S. 304 grade POST 100 x 100 x 150mm Base plate 200 x 200 mm + SS Post 150mm HT in, size- 450 x 300

Entry/ Exit Signage Signage is to be made of Acrylic 4mm thick Box with translucent vinyl pasting on it. Illuminated with led Light (Four Sided) Mounted on S.S. 304 grade POST 100 x 100 x 150mm Base plate 200 x 200 mm + SS Post 150mm HT out, size- 450 x 300

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Stair Direction at landing, size- 300 x 125mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Stair No, size- 400 x 125mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Stair Floor Level Indicator, size- 382 x 382mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Fire Safety Disclaimer, size- 300 x 300mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" FHC, size- 150 x 200mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Fire alarm, size- 150 x 200mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Fire Exit , size- 600 x 175mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Evacuation Plan A2, size- 420 x 514mm

"Photoluminicent Signages Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with premium photoluminicent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge BRAND/MAKE- 247SIGN/ ASB Ads/ Glo-Lite" Evacuation Plan A3, size- 297 x 420mm

"Emergency Evacuation signage ( Battery backup ) ITEM Name:-Edge Lit Emergency Signage MODEL - EMEX3726- Premium Casing:-Anodised Aluminium with Plastic / Metal Side Caps. Signages Over all size :-375 x 260 mm Text Panel:-8 mm Acrylic Back Up Duration :- 180 Minutes Primary Power Source:-AC - 150-240 Volt Luminarre:-LED Battery Disconection Swith Battery Capacity:- 2000 AMH Battery Type:- Lithium ION AC to DC Built in Adaptor Fuse for Circuit protection AC, Charging, EMERGENCY Indicators Emergency Test Switch Battery Minimum Discharge Protection Battery Maximum Charge Protection Installation:- In client scope through certified electrical contractor. MAKE- 247 sign/ Glo-Lite/ Prolite" BB Directional, size- 375 x 260mm

"Emergency Evacuation signage ( Battery backup ) ITEM Name:-Edge Lit Emergency Signage MODEL - EMEX3726- Premium Casing:-Anodised Aluminium with Plastic / Metal Side Caps. Signages Over all size :-375 x 260 mm Text Panel:-8 mm Acrylic Back Up Duration :- 180 Minutes Primary Power Source:-AC - 150-240 Volt Luminarre:-LED Battery Disconection Swith Battery Capacity:- 2000 AMH Battery Type:- Lithium ION AC to DC Built in Adaptor Fuse for Circuit protection AC, Charging, EMERGENCY Indicators Emergency Test Switch Battery Minimum Discharge Protection Battery Maximum Charge Protection Installation:- In client scope through certified electrical contractor. MAKE- 247 sign/ Glo-Lite/ Prolite" BB Exit, size- 375 x 260mm

Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. Lift No , size- 200 x 85mm

Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. No smoking / No littering, size- 300 x 400mm

Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. Floor level indicator lift, size- 250 x 250mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." Room indentification, size- 450 x 156mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." Department indentification, size- 650 x 200mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." Wash room ( Wall mounted ), size- 156 x 156mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." Floor directory, size- 600 x 1500mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." Service directoru, size- 900 x 1800mm

"ROOM INDETIFICATION Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." ROOM NO, size- 156 x 156mm

"Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front inside. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. This is double sided signages having twim plates. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." WAY FINDING 2 WAY, size- 1200 x 500mm

"Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/bronze finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 1mm protective sheet in front inside. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 3 mm Thickness in molded PVC of matching color as that of anodising without paint, side caps to be fixed to main plate using SS L key screws or same color coated L key screws as anodising. signages to be bilingual/trilingual language with pictograph as required. This is double sided signages having twim plates. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System." WAY FINDING 1 WAY, size- 1200 x 250mm

Double sided signage will be fabricated using 12+12 mm twin thick ultra slim edge modular aluminium extruded profile with approved ACP as base daily fixed over on both side and reflective vinyl duly digitally cut and pasted on ACP panels on both side. Signage will be hanged using SS csble/ SS chain with fastners. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. DOUBLE TEXT, size- 1200 x 300mm

Double sided signage will be fabricated using 12+12 mm twin thick ultra slim edge modular aluminium extruded profile with approved ACP as base daily fixed over on both side and reflective vinyl duly digitally cut and pasted on ACP panels on both side. Signage will be hanged using SS csble/ SS chain with fastners. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Tripple Text, size- 1500 x 300mm

"Poster frame made of alloy 6063 having copper/bronze anodizing, clip on arrangement for easy change of insert. Use 2mm clear acrylic as a protection layer in the front. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA" A3, size- 297 x 420mm

"Poster frame made of alloy 6063 having copper/bronze anodizing, clip on arrangement for easy change of insert. Use 2mm clear acrylic as a protection layer in the front. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA" A2, size- 420 x 514mm

Single side signage will be fabricated using 12mm thick ultra slim edge modular aluminium extruded profile with approved ACP as base daily fixed over on both side and reflective vinyl duly digitally cut and pasted on ACP panels on both side. Signage will be hanged using SS csble/ SS chain with fastners. BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System. Car parking, size- 600 x 900mm

ELECTRICAL- EXTERNAL WORKS TRANSFORMER Supply, installation, testing and commissioning of 1600 KVA, 33 kV/0.433 kV, 3 Phase, 4 wire, 50 Hz., ON-AN Transformer, Dyn11 Vector group, copper bound Class A insulation with outdoor duty type, On load tap changer on HV Side range -15%, 0, +5% in the steps of 1.25% per step, type transformer with RTCC+AVR inclusive of all control cable. Cable box connection including cable adapter box at primary and secondary end (LT side) shall be connected through busduct/ cable, complete with all accessories including first filling of oil, double float buchholz relay protection, high winding temperature, oil temperture sensors and gauges etc. as per to IS 1180 ammended upto date, interconnection of control cables and accessories etc complete including Foundation . All instruments Contact wiring to be done up to Marshalling box. Installation & testing shall be done by the electrical contractor in the presence of engineer in charge. The supplier shall certify that the Transformer has installed as per norms.

DG SETS Supply & installation of 1250 KVA OPEN DG Set comprising of Cummins make engine model KTA 50 G3 developing 1470 BHP Coupled to 415 V STAMFORD make alternator mounted on a common base frame, complete with:(a) Fuel tank 990 Ltrs. ( Outside Enclosure) (b) Batteries & Leads. (c) AVM Pads (d) Silencer. (e) First fill of lube oil. (f) Radiator

Acoustic enclouser

EXHAUST SYSTEM Supply of exhaust piping of following sizes MS B Class exhaust pipes conforming to IS:3589 with welding joint including bends, clamps, dash fastener, flanges, nuts, bolts etc. complete as required and as per specifications detailed below. 10" dia. (250 mm NB), MS, 4.85 mm thick plate, Exhaust pipe

EXHAUST SYSTEM Supply of exhaust piping of following sizes MS B Class exhaust pipes conforming to IS:3589 with welding joint including bends, clamps, dash fastener, flanges, nuts, bolts etc. complete as required and as per specifications detailed below. 14" dia. (350 mm NB), MS, 4.85 mm thick plate, Exhaust pipe

Supply of 50mm thick glasswool /mineral wool, wire chicken mesh over insulation and 24 gauge aluminium sheet cladding over the following sizes exhaust pipes from silencer to atmosphere. 10" dia. (250 mm NB), MS, 4.85 mm thick plate, Exhaust pipe

Supply of 50mm thick glasswool /mineral wool, wire chicken mesh over insulation and 24 gauge aluminium sheet cladding over the following sizes exhaust pipes from silencer to atmosphere. 14" dia. (350 mm NB), MS, 4.85 mm thick plate, Exhaust pipe

y bend

Supply and installation of Aluminium cladding for residencial silencers with Mineral Wool 50mm Thick, density 64 Kg/cu.mtr., wire mesh and 24 gauge aluminium cladding.

Supply and installation of SS Flexible Bellows, 14" dia. (350 mm NB), complete with counter flanges, heat resitant gaskets, nuts-bolts-washers etc., complete as required.

Supply and installation of MS Support structure The MS Structure. will be duly coated with two coats of red-oxide primer and two coats of enamel paint. The colour shade of final paint will be as decided by the client.(Combined structure for 2 DG set)

Supply and installation of Lightening Arrestors Non Seamer Type with GI Strip upto Earth Pit

Supply and installation of Aviation light with UPS and Cable upto light

POWER CABLING 3.5Cx300sqmm, 8 runs, PVC Insulated XLPE, 1.1kV grade Aluminium armoured type cable (considering panel placed at a distance of 20mtrs)

Cable termination kit for 3.5Cx 300sqmm power cable

CONTROL CABLES Supply & laying of Power & Control Cables 24C x 2.5 Sqmm CU armoured Control Cable.

CONTROL CABLES Supply & laying of Power & Control Cables 4C x 2.5 Sqmm CU armoured Control Cable.

CONTROL CABLES Supply & laying of Power & Control Cables 2C x 2.5 Sqmm CU armoured Control Cable.

CONTROL CABLES Supply & laying of Power & Control Cables 2C x 4 Sqmm CU armoured Control Cable.

CONTROL CABLES Supply & laying of Power & Control Cables 3C x 6 sqmm

Providing & Fixing of Cables End Termination for following size of cables. 24C x 2.5 Sqmm CU armoured Control Cable.

Providing & Fixing of Cables End Termination for following size of cables. 4C x 2.5 Sqmm CU armoured Control Cable.

Providing & Fixing of Cables End Termination for following size of cables. 2C x 2.5 Sqmm CU armoured Control Cable.

Providing & Fixing of Cables End Termination for following size of cables. 2C x 4 Sqmm CU armoured Control Cable.

Providing & Fixing of Cables End Termination for following size of cables. 3C x 6 sqmm

FUEL PIPING Supply and Installation of MS Class C Pipe 25 mm (Considering DG set to be placed at a distance of 5-6 mtr)

Supply and fixing of set of Fuel Pipe fittings like bends, flanges, valves, tee, elbows etc.

EARTHING Earthing with Copper earth plate 600mm x 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.

Earthing with GI earth plate 600mm x 600mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.

Supply, Installation, of following bare strips including all necessary fixing accessories and effecting connections as per specifications. Cu flat size 50 x 6mm

Supply, Installation, of following bare strips including all necessary fixing accessories and effecting connections as per specifications. GI MS flat size 50 x 6 mm

UPS SYSTEM 2 Nos. of Modular 100 kVA/kW UPS in parallel Conf. Supply, unloading, shifting, installation, testing & commissioning of micro processor controlled 2 Nos. of 100 kVA/kW UPS (Module Rating 25 - 50 kW) operating in parallel configuration for 100% load, IGBT based rectifier to achieve input THDI < 3% and input power factor of greater than 0.99 at 100% loading. AC - AC Effieicny: Greater than equal to i.e. ≥ 97 % in Online Double Conversion Greater than equal to i.e. ≥ 98 % in Static Bypass Mode along with PF Correction to Unity at Input & Harmonic Correction (THDI) to < 5% at Input at 100 % Load. Makes -Schneider / vertia / Tmiec Fully rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in UPS module. 110% rated Inbuilt static switch at the static bypass line integrated in UPS module. Web-enabled Monitoring and Management through SNMP protocols for multi-OS environments with below features.

Giving notifications like e-mail, paging notification, broadcast notification, battery replacement notification, run event-based scripts. Event logging, data logging and action logging Automated unattended shutdown of computers. Local notification through audible alarm. RS-485 port with BUS/MODBUS card, communication protocol to integrate the UPS with building management system and for field analysis. Inbuilt / External Phase Sequence corrector at Input Inbuilt Backfeed protection at Mains & Bypass Rodent Mesh & User replaceable Dust Filters Top & Bottom Cable entry shall be provided with aluminium cable termination. IP 21 AC/DC Capacitors - 10 years Operating Life. One time replacement cost shall be considered in the offer incase of devation (To be a part of PO) Energy Meters for Recording Input kWh & Output kWh required. Waveform capturing meters for recording the waveforem during an event/failure for Input voltage, Bypass voltage, Output voltage, Output current, Battery voltage, Ground voltage, DC bus voltage Mobile App Based Software for monitoring UPS parameters on Smart Phone itself shall be provided. "UPS shall be capable to operate in Normal Online Operation even during the Mains Input Neutral Failure and shall support Single Phase loads also at the Output. Incase Vendor does not comply, a Input K13 Copper Wound, 165 KVA (110% of Frame Capacity as UPS is Scalble to 150 kVA) Transformer shall be provided to meet the same."

LIB Battery (Samung/LG/Panasonic): 30 Minutes of backup at Unity Power factor i.e. 100 kW. Design Margin of 15% dhall be considered while sizing the battery. Shall be UL 9450A Certified, Test Method for Evaluating Thermal Runaway Fire Propagation in Battery Energy Storage Systems. Certificate shall be provided by the Vendor/OEM

Installation & Commissioning Charges

Supplying, installation, connecting, testing & Commissioning of followings: SOLAR SYSTEM WORKS (100kW Plant) 10 kW grid tied Inverter. (Make: Omnik)

315-325W, PV Modules. (Make: Waaree / Rhine)

4 sqmm DC Cu wire for solar system cennectivity.

MC4 Cnnector (Pair)

Cable clips, tise, thimbles, nuts & bolts

Galvanised Iron Mounting Structure

Foundation / Ballast

Lightning protection system.

Earthing Kit with strips.

Polyamide conduit with connector & Brackets.

Installation, connecting, testing & Commissioning of entire system including all related supplies complete as required.

SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required. 2C x 6 Sq.mm Al. XLPE arm.

SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required. 4C x 10 Sq.mm Al. XLPE arm.

SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required. 4C x 16 Sq.mm Al. XLPE arm.

SUPPLY OF EXTERNAL LIGHTING SYSTEM Supply of Pole mounted 60W LED Street Light, luminous efficiency of luminaire ≥ 100 lm/W & total Lumen Output of 6000Lm, colour rendering index Ra > 70. Service life L70(tq 25 °C) = 50,000 h. Pressure die cast aluminium painted mounting spigot suitable for horizontal mounting with tilt flexibility of +/- 10 degrees & wide photometry, Ingress Protection rating IP66 & impact resistance of IK08. Power Factor ≥ 0.95, THD should be ≤ 10%. Surge protection should be ≥ 10kV. All luminaires shall be with associated driver, lamp and other connecting or mounting accessories to make it complete in all respect for operational purpose.

Supply, installation, testing and commission of The pole shaft shall be made single piece MS structure continuously tapered having polygonal (8/12 sides) cross section and a single longitudinal welding.Top dia 70mm and bottom dia 130 mm, thickness 3mm , height 6m. The welding will be done as per BS 5135 / IS 9595. No circumferential welding shall be allowed in the pole shaft. The MS shall conform to BSEN 100025/100027. The structure shall be single hot dip galvanized as per BS 729 / IS 2629. A suitably designed door shall be provided at approximate 700mm height from the pole base. The door opening will be suitably reinforced for structural strength. The door shall be flushed with pole external surface and shall provide easy access for electrical connections at a maintainable height. A Suitable base flange will be welded and plate reinforcements will be provided between base flange & pole. Base Plate 220x 220 x 16mm Foundation accessories will be as per IS 1367

Supply, Installation, testing and commissioning of Decorative post-top luminaire with connected load 39W with required lamps complete with, control gears, ballast, capacitor etc. including connection with 3x1.5 sqmm flexible fire retardant copper connecting wire of required length complete as required.

Supply, installation, testing and commissiong of LED bollard luminaire, 660 mm. Installation of bollard luminaire in firm underground via baseplate. Mounting in the substrate is via suitable underground support (accessory). 6 LEDs behind semi-specular plastic cover, direct distribution. With rotationally symmetrical wide light distribution. Further beam characteristics are available for flexible adaptation to customer-specific lighting tasks. Retrofitting a rear shielding is possible, available as accessory to be ordered separately. Luminaire luminous flux 800 lm, connected load 11W, luminous efficiency of luminaire 73 lm/W. Light colour warm white, colour temperature 3000 K, colour rendering index Ra > 70. Service life L80(tq 25 °C) = 80,000 h. Supporting column of extruded aluminium section, Round section Ø 170 mm. Anthracite colour, similar to DB703 with metal effect, highly weather resistant, powder-coated. Cylindrical cover of impact-resistant PMMA, clear. Safety class II, protection rating IP65. With electronic transformer, switchable.

Supply of Mast/Surface mounted LED Flood Light Fixtures with luminous efficiency of luminaire ≥ 120 lm/W colour rendering index Ra > 70. Service life L70(tq 25 °C) = 50,000 h. LED Flood Light luminaire luminous flux ≥ 6000 lm, connected load ≤ 50 W Pressure die cast aluminium body heat sink with mounting accessories to tilt the fixtrue horizontally & vertically to mount the fixtrue as per requirement. Ingress Protection rating IP66 & impact resistance of IK08. Power Factor ≥ 0.95, THD should be ≤ 10%. Surge protection should be ≥ 15kV (10kV internal & 5kV) . All luminaires shall be with associated driver, lamp and other connecting or mounting accessories to make it complete in all respect for operational purpose.

Erection of 6 meter high street light GI pole including providing and casting in position 'M20' grade reinforced cement concrete pole foundation i/c excavation of earth in all kind of soils including foundation.

Supplying, drawing, connecting and testing of following size of PVC insulated FRLS copper conductor (as per IS : 694) flexible multicore wire in the existing poles and bracket from cable termination connector / MCB to the fitting i/c providing suitable connectors. 3 core 2.5 sq.mm (for 6 Mtr Poles)

Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia GI wire in surface or in recess for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 2 x 6 sq. mm (19mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 x 10 sq. mm (25mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 x 16 sq. mm (28mm)

Supply and fixing of following sizes of medium class PVC conduit alongwith accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm.

Supply and fixing of following sizes of medium class PVC conduit alongwith accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm.

Supply and fixing of following sizes of medium class PVC conduit alongwith accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm.

Providing, Laying and fixing following dia RCC pipe NP2 class below road crossing (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75cm deep) and refiling etc. as required. Supply and fixing of following sizes of medium class PVC conduit alongwith accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 100 mm dia.

Supply of following 33 kV (E) grade multicore Aluminium conductor XLPE insulated cable, insulation screening with extruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required. 3 C x 240 Sq. mm 33 kV (E)

UPS I/P Panel (ACADEMIC BLOCK ) INCOMER: 1 Nos. 200A TP+N MCCB's with microprocessor based releases with isolable neutral, ON indication in an enclosure complete with wiring as required. (+) Packing & Forwarding @ 2% (+) Installation @ 10%

UPS O/P Panel (ACADEMIC BLOCK ) INCOMER: 1 Nos. 200A TP+N MCCB's with microprocessor based releases with isolable neutral, ON indication in an enclosure complete with wiring as required. Indication/metering for each incoming 3 set of RYB phase Indication lamps with suitable rating MCB 3 set of ON/OFF indicating lamps along with 2A SP MCB backup protection. BUS BAR Electrolytic high conductivity Copper Three phase and 200% neutral busbars rated at 300 amps, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. The current density of Bus-Bars shall not be more than 1.4 Amps/ sq. mm. The busbar sizing calculations shall be sumitted for approval, considering all derating factors. OUTGOING 3 Nos. 160A/35kA 3P+2N MCCB with 200% solid neutral link & Ics breaking capacity with ON/OFF indications & back-up MCB. 1 Lot of control wiring 1 Set of designation plates (+) Packing & Forwarding @ 2% (+) Installation @ 10%

UPS I/P Panel (EMERGENCY BLOCK ) INCOMER: 1 Nos. 160A TP+N MCCB's with microprocessor based releases with isolable neutral, ON indication in an enclosure complete with wiring as required. (+) Packing & Forwarding @ 2% (+) Installation @ 10%

UPS O/P Panel (EMERGENCY BLOCK ) INCOMER: 1 Nos. 160A TP+N MCCB's with microprocessor based releases with isolable neutral, ON indication in an enclosure complete with wiring as required. Indication/metering for each incoming 3 set of RYB phase Indication lamps with suitable rating MCB 3 set of ON/OFF indicating lamps along with 2A SP MCB backup protection. BUS BAR Electrolytic high conductivity Copper Three phase and 200% neutral busbars rated at 300 amps, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. The current density of Bus-Bars shall not be more than 1.4 Amps/ sq. mm. The busbar sizing calculations shall be sumitted for approval, considering all derating factors. OUTGOING 4 Nos. 63A/35kA 3P+2N MCCB with 200% solid neutral link & Ics breaking capacity with ON/OFF indications & back-up MCB. 1 Lot of control wiring 1 Set of designation plates (+) Packing & Forwarding @ 2% (+) Installation @ 10%

TVSS Supply, installation, testing & commissioning of 50 kA surge handling capacity TVSS with 10 mode protection including EMI & RFI filters in a wall mounted sheet steel powder coated enclosure with locable door and with 4P MCB/ 4P MCCB of 50kA fault with stand capacity and complete with wiring as required. (+) Packing & Forwarding @ 2% (+) Installation @ 10%

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 4 C x 25 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 35 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 50 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 70 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 95 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 120 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 150 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 185 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 240 Sq.mm Al. XLPE arm.

LT CABLE AND ACCESSRIES SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 3.5 C x 300 Sq.mm Al. XLPE arm.

"SAFETY EQUIPMENT Supply, installation and fixing of the following equipment at suitable place in the sub-station building as required:-" M.S bucket of 9 liters capacity painted with red oxide paint & lettered as 'Fire' with White and red mounted on freestanding stand, as required including filling with dry sand.

"SAFETY EQUIPMENT Supply, installation and fixing of the following equipment at suitable place in the sub-station building as required:-" First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963.

"SAFETY EQUIPMENT Supply, installation and fixing of the following equipment at suitable place in the sub-station building as required:-" Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English).

"SAFETY EQUIPMENT Supply, installation and fixing of the following equipment at suitable place in the sub-station building as required:-" Rubber Mat 914.4 mm wide and 12 mm thick checkered rubber mat to withstand 33 KV dielectric strength confirming to IS : 5424 -1969 complete as required.

"SAFETY EQUIPMENT Supply, installation and fixing of the following equipment at suitable place in the sub-station building as required:-" Supply and fixing of Carbon Dioxide fire extinguishers of 4.5 Kg each mounted on wall hooks as per IS 2878-1976.

TELEPHONE SYSTEM Providing, fixing, connecting & testing of External type (IP 65) Telephone Tag Block krone type in a suitable size 1.6 mm thick dust and vermin proof Sheet steel enclosure duly painted by synthetic enamel over anti corrosive primer, lockable and hinged cover with provision for cable through glands complete in all respects. 500 pair krone

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 100 pair

"H V CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 33 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required." Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 33 KV grade of following size direct in existing RCC / HUME / METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm

H.T Termination Supply and making Indoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 33kV ( UE )grade as required." 3 C x 240 Sq.mm ( 33kV UE )

Supply and making Outdoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 33kV ( UE )grade as required.3 C x 240 Sq.mm (33kV UE )

E A R T H I N G Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 50 mm x 10 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 35 sq. mm (32mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 95 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 120 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 150 sq. mm (50mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 185 sq. mm (57mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 240 sq. mm (62mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ x 300 sq. mm (70mm)

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width x 50 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 750 mm width x 62.5 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 900 mm width x 62.5 mm depth x 2.0 mm thickness

Providing and fixing MV danger notice plate of 200 mm x 150 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required.

Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required.

"ELECTRICAL- LIGHTING PROTECTION LIGHTNING PROTECTION AS PER IEC 62305 / IS IEC 62305 AT LVL -III (15X15 MTR )" Supply of Vertical Electrolytic Copper Lighting Arrester of 16 mm dia, 1000 mm long with Gun Metal base plate . Model : APSAT116CB+APSTB16-253 Make : APS /Hakel

Supply 8 mm round aluminium conductor for horizontal lightning protection - run in roof. Model : AL8. Make : Hakel / APS

Supply of roof conductor holder for 8 mm round aluminium conductor made of Gun Metal for horizontal installation. The distance between each holder should be min of 1 mtr. Model : APSRCS50. Make : Hakel / APS

Supply of T connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSTCRC50 , Make : Hakel /APS

Supply of Cross connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of Expansion piece along with connector to compensate the expansion of round 8 mm Al conductor when temperature variation . Connection should be in every 20 mtr. Model : APSEXP50 , Make : Hakel/APS

DOWN CONDUCTOR & RING CONDUCTOR AS PER IEC 62305 Supply of 8 mm round aluminium conductor as a down conductor mounted in the surface of wall which will carry the lightning current to earth pit. Model : AL8. Make : APS

Supply of Down conductor holder for 8 mm round aluminium conductor of min distance between the wall to the conductor will be of 85 mm. The distance between each holder should be min of 1 mtr. Model : APSRCS50 Make : APS

Supply of straight connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSPCRC50, Make : APS

Supply of 6 digit lightning strike counter. Model - LEC06 Make - NEXUS

Supply of Test Joint Point for 8 mm round aluminium conductor , the size should be of 25 x 3 x 150 mm copper in ABS boxes. Model : APSTLBCU. Make : APS

EARTHING AS PER IEC 62561- 2 & 7 Supply of UL LISTED low carbon high tensile steel rod with copper coating of min 254 micron JK Chemrode -JK0110 CBR the dia should be 25.4 mm with length of 10 feet ( 3000 mm) . The rod shall be as per IEC 62561-2 and approved by UL 467. The rod shall be tested fromCPRI lab for current discharge 50kA peak. The Chemrode shall be surrounded with 25 kg (2 bag) of Earth enhance materiel JK Reslow according to IEC 62561-7 and the Chemical resistance value shall not increase more then 0.067 Ωm along with earth pit chamber made up polyplastic. Size of -254x330x260 MM earth pit chamber cover should be tested and certified for 9tonne load bearing capacity from any central government lab (national test house Gaziabad uttar pradesh )(Model- PPC01) Make :APS/JK Chemrode

Installation of above Lighting Protection items

"""ELECTRICAL - INTERNAL WORKS SUB HEAD - I : POINT WIRING & ACCESSORIES WIRING IN PVC CONDUIT ""Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required." Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit ,2way modular switch,modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc.as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required. (For light plugsto be used in non residential buildings).

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 2X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 2X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 2X 10 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 4X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 4X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 4X 16 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor ,single core cable in surface /recessed medium class PVC conduit as required. 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.32 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.40 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.50 mm

Supplying and fixing following modular switch/socket on the existing modular plate switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/socket on the existing modular plate switch box including connections but excluding modular plate etc. as required. TV socket outlet

Data outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Providing and fixing circular/hexagonal G.I.box for ceiling fan clamp of internal dia 140mm,73mm height,top lid of 1.5 mm thick G.I.sheet with its top surface hacked for proper bonding ,top lid shall be screwed into the G.I.box by means of 3.3mm dia round headed screws,one lock at the corners.Clamp shall be made of 12mm dia M.S.bar bent to shape as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100 mmX75 mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required..

Supplying and fixing call bell/buzzer suitable single phase ,230V, complete as required

Wiring with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 5Light light point controlled by MCB from DB(Cost of MCB is not included)

Wiring with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 6Light light point controlled by MCB from DB(Cost of MCB is not included)

Wiring with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 7Light light point controlled by MCB from DB(Cost of MCB is not included)

INVERTER SYSTEM Supplying including installation of Inverter (Su-Kam/ Microtech/ V-Guard/ Luminous) with Battery and its case as per direction and specified by the Deptt. Sine wave Inverter 1400 VA/240 V

LIGHTING FIXTURES & FANS Supply, Installation,testing & commisioning of Sleek surface LED Batten. Suspended / Surface Mounted with length of 1150 mm available. With diffused polycarbonate cover, integrated flush into the luminaire body. Best in class LEDs, with Luminaire luminous flux 3960lm, connected load 36W, luminous efficiency of luminaire 110 lm/W. Light Colour temperature- 3000 K/ 4000 K/ 5700 K, Colour rendering index Ra > 80. Operating Temperature range: -10degC to 45degC, IP 20. Extruded Aluminium Housing with 28X43X1150mm(WxHxL) (Make- Trilux Make TSmart Linea F OTA 4000-857 ET or equivalent in Disano/ LT )

Supply, Installation,testing & commisioning of LED surface mounted downlight of 10 watt using COB Technology. Deep front frame cut for enhanced visual comfort and glare cut off offering UGR < 19 and CRI > 80. Tool less installation with spring mounting. Luminaire body made of Die -cast aluminium. With aluminium reflector offering option of beam angles 24°, 40° & 60°. Trim with RAL shades of Black & White. (Make- Trilux Orion 10 watt or equivalent in Disano/ LT )

Supply, Installation,testing & commisioning of Sleek surface LED Batten. Suspended / Surface Mounted with length of 384mm available. With diffused polycarbonate cover, integrated flush into the luminaire body. Best in class LEDs, with Luminaire luminous flux 1100lm, connected load 10 W, luminous efficiency of luminaire 110 lm/W. Light Colour temperature- 5700 K, Colour rendering index Ra > 80. Operating Temperature range: -10degC to 45degC, IP 20. Extruded Aluminium Housing with 28X43X384mm(WxHxL) (Make- Trilux TSmart Linea T OTA 1200-857 ET or equivalent in Disano/ LT)

Supply, Installation,testing & commisioning of translucent PMMA Cover. for system ceiling with exposed grids, false ceiling. Dimension ( L x w x H) 595mm x 595 mm x 90mm, cut out dimension (L x W) 570mm x 570 mm Harmonious light effect due to homogeneously illuminated light emmisions.Cover of translucent PMMA. with Luminaire luminous flux 3600lm, connected load 36W, luminous efficiency of luminaire 100 lm/W. Light Colour temperature- 5700 K, Colour rendering index Ra > 80 Service life 50000 operating hours. Power coated CRCA, white (Make- Philips/ Trilux /Osram or equivalent )

Supply, Installation, Testing & Commissioning of 10W LED Bulkhead made of Pressure Die cast aluminium With white Powder Coating Finish.Fixture should have minimum efficacy at System level (Not Chip Level) >=90lumens/watt, 900 Lumen, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT - 6500 (SDCM<5), CRI >80 ; IP65 (Make:- Trilux Bulkhead optima or equivalent. )

Supply, Installation, Testing & Commissioning of Self contained emergency light units 1x9 watt double sided for wall / ceiling mounting with suspension / mounting kit, lamps, inbuilt standby battery (for 2 hours backup) and battery charger etc. in suitable enclosure. Make - Prolite or equivalent.

Supply of pre-wired, decorative type mirror light with 10W LED lamps of all types, complete with all accessories etc. directly on wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying including fitting and fixing of following star rated A.C. ceiling fan complete with all accessories like down rod, canopy etc of following sweeps with making necessary connection cable as approved by Deptt.s etc as required complete and as directed by the department as required complete etc. (Without regulator). (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.) Energy efficient 5-star 1200 mm sweep. (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.)

Supply of the following sizes exhaust fans. 300 mm sweep

Supply of the following sizes exhaust fans. 450 mm sweep

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

SupplTELECOMMUNICATION SYSTEM (DATA, TELEPHONE & TV) (CONDUITING & CABLING/WIRING ONLY.) ying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

SupplTELECOMMUNICATION SYSTEM (DATA, TELEPHONE & TV) (CONDUITING & CABLING/WIRING ONLY.) ying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

SupplTELECOMMUNICATION SYSTEM (DATA, TELEPHONE & TV) (CONDUITING & CABLING/WIRING ONLY.) ying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

SupplTELECOMMUNICATION SYSTEM (DATA, TELEPHONE & TV) (CONDUITING & CABLING/WIRING ONLY.) ying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 40 mm

SupplTELECOMMUNICATION SYSTEM (DATA, TELEPHONE & TV) (CONDUITING & CABLING/WIRING ONLY.) ying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 50 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1 Pair

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 10Pair armoured cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 5Pair Krone type telephone tag block

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 40Pair armoured cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 50Pair armoured cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 10Pair Krone type telephone tag block

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 40Pair Krone type telephone tag block

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 100Pair armoured cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 100Pair Krone type telephone tag block

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 400Pair Krone type telephone tag block

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

MCB DISTRIBTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)" 8 way, Double door

MCB DISTRIBTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)" 12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting,vertical type, 415 V, TPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required.(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole .

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required. 40 A .

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing Cable End Box (Loose wire box)(IP 43)suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. For 8 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose wire box)(IP 43)suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. For 10 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required. For 4 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required. For 8 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose wire box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

"CABLE TRAY //DWC HDPE PIPE/RACEWAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required." 100 mm width X 50 mm depth X 1.6 mm thickness

"CABLE TRAY //DWC HDPE PIPE/RACEWAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required." 150 mm width X 50 mm depth X 1.6 mm thickness

"CABLE TRAY //DWC HDPE PIPE/RACEWAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required." 200 mm width X 50 mm depth X 1.6 mm thickness

"CABLE TRAY //DWC HDPE PIPE/RACEWAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required." 300 mm width X 50 mm depth X 1.6 mm thickness

"CABLE TRAY //DWC HDPE PIPE/RACEWAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required." 450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level)including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)

Fabricating supplying to site of installation, in floor including chase cutting of floor,leveling, refilling and making good the same from 1.6 mm thick and 2 mm thick cover pregalvanised GI raceways, totally enclosed, height 40 mm . The two lengths of raceways shall be fitted with Collars , 50 mm wide, 3 mm thick , press fit type. The raceways shall be clamped to the floor slab with GI clamps , 3mm thick and shall be screwed to the floor slab. The joint between raceway and junction box will be made with GI flexible strip( 3 nos), 3 mm thick, 4 inches long ,15 mm wide which will be nut bolted to the Junction box complete as required etc. 100MM X38MM (1COMPARTMENT)

Fabricating supplying to site of installation, in floor including chase cutting of floor,leveling, refilling and making good the same from 1.6 mm thick and 2 mm thick cover pregalvanised GI raceways, totally enclosed, height 40 mm . The two lengths of raceways shall be fitted with Collars , 50 mm wide, 3 mm thick , press fit type. The raceways shall be clamped to the floor slab with GI clamps , 3mm thick and shall be screwed to the floor slab. The joint between raceway and junction box will be made with GI flexible strip( 3 nos), 3 mm thick, 4 inches long ,15 mm wide which will be nut bolted to the Junction box complete as required etc. 150MM X38MM (1COMPARTMENT)

Fabricating supplying to site of installation, in floor including chase cutting of floor,leveling, refilling and making good the same from 1.6 mm thick and 2 mm thick cover pregalvanised GI raceways, totally enclosed, height 40 mm . The two lengths of raceways shall be fitted with Collars , 50 mm wide, 3 mm thick , press fit type. The raceways shall be clamped to the floor slab with GI clamps , 3mm thick and shall be screwed to the floor slab. The joint between raceway and junction box will be made with GI flexible strip( 3 nos), 3 mm thick, 4 inches long ,15 mm wide which will be nut bolted to the Junction box complete as required etc. 300MM X38MM (3COMPARTMENT)

FLOOR JUNCTION BOX 150MM X 150MM X50MM DEEP JB

FLOOR JUNCTION BOX 225MM X 225MM X50MM DEEP JB

FLOOR JUNCTION BOX 400MM X 400MM X50MM DEEP JB

"1 Nos. of Modular 50 kVA/kW UPS in N+1 redundancy where N is 50 kVA Supply, unloading, shifting, installation, testing & commissioning of micro processor controlled 1 Nos. of 50 kVA/kW UPS (Module Rating 25 - 50 kW) operating for 100% load, IGBT based rectifier to achieve input THDI < 3% and input power factor of greater than 0.99 at 100% loading. AC - AC Effieicny: Greater than equal to i.e. ≥ 97 % in Online Double Conversion Greater than equal to i.e. ≥ 98 % in Static Bypass Mode along with PF Correction to Unity at Input & Harmonic Correction (THDI) to < 5% at Input at 100 % Load. Active Harmonic Filter shall be provided of rated capacity in a seperate cabinet at Static Bypass Circuit if this feature is not builtin along with Battery Charger to chanrge the batteries in Static bypass mode of operation. This arrangament shall be Certifed by the Third Party (UL / TUV / NABL Accrediated Lab)" 120% rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in UPS module. 110% rated Inbuilt static switch at the static bypass line integrated in UPS module. Web-enabled Monitoring and Management through SNMP protocols for multi-OS environments with below features. Giving notifications like e-mail, paging notification, broadcast notification, battery replacement notification, run event-based scripts. Event logging, data logging and action logging Automated unattended shutdown of computers. Local notification through audible alarm. RS-485 port with BUS/MODBUS card, communication protocol to integrate the UPS with building management system and for field analysis.

Inbuilt / External Phase Sequence corrector at Input Inbuilt Backfeed protection at Mains & Bypass Rodent Mesh & User replaceable Dust Filters Top & Bottom Cable entry shall be provided with aluminium cable termination. IP 21 Harmonic Filters at Static Bypass path for < 5% at 100% load Input Power Factor correction to unity at Static Bypass path at 100% load AC/DC Capacitors - 10 years Operating Life. One time replacement cost shall be considered in the offer incase of devation (To be a part of PO) Energy Meters for Recording Input kWh & Output kWh required. Waveform capturing meters for recording the waveforemtrend during an event/failure for Input voltage, Bypass voltage, Output voltage, Output current, Battery voltage, Ground voltage, DC bus voltage Mobile App Based Software for monitoring UPS parameters on Smart Phone itself shall be provided. Overloading: 125% for 10 minutes and 150% for 1 Minute "UPS shall be capable to operate in Normal Online Operation even during the Mains Input Neutral Failure and shall support Single Phase loads also at the Output. Incase Vendor does not comply, a Input K13 Copper Wound, 55 KVA Transformer shall be provided to meet the same."

LIB Battery (Samung/LG/Panasonic): 30 Minutes of backup at Unity Power factor i.e. 50 kW. Design Margin of 15% shall be considered while sizing the battery. Shall be UL 9450A Certified, Test Method for Evaluating Thermal Runaway Fire Propagation in Battery Energy Storage Systems. Certificate shall be provided by the Vendor/OEM Installation & Commissioning Charges

Supply Installation, Testing, comm of CCTV Survillance Dome Fixed lens camera 2 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Dome Camera, 1/2.8" CMOS, 2 MP @ 60fps, Min. Illumination required 0.01 lux @ F1.4 (color), 120dB True WDR, Min. Pixels 1920 × 1080, 2.8 mm lens, BLC, HLC, 3DNR, Privacy Mask, 3 IR LEDs Smart IR with upto 15m IR distance, inbuilt mic , Audio support, 128GB SD card support, IP66, IK10, PoE, H.265, PoE Class 3 and 12V DC, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S & Profile G compliant, UL, CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant.

Bullet Camera 2 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/2.8" CMOS, 2 MP @ 60fps , triple stream, Min. Illumination required 0.01 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 1920 × 1080, triple stream, 2.7–13.5 mm motorized focus & zoom lens, S/N ratio - 50 dB min, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265,H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, Profile G & profile Q compliant, UL, CYber Security certified,CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant.

Supply Installation Testing & Commissioning of Network Storage Manager(NSM) supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec, 3D PTZ control, 360° Fisheye camera and multi-imager/lens camera support, and intelligence events. System proposed shall have scalability of upto 128 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF, Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity.

Supply, Installation, Testing & Commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec, multi-imager/lens cameras and 360° fisheye cameras. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's from a multiple location licenced for 250 cameras & 2 users clients, licenses should expandable upto 500 cameras & 10 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, General Data Protection Regulation (GDPR) compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall have support for iLIDS certified Analytics like intrusion/LoiteTrace.

Server for NVR software - NSM shall have Intel® Core™ 2xIntel® E5-2620 v4, 2.1 GHz or better, Mnimum 32GB RAM, 1+1 1200W hot plug redundant power supply, OS drive: x 2.5" Hot Swappable SATA HDD Protected by RAID 1; 12 field upgrade 4 TB or 8 TB or 10 TB or 12 TB SATA/SAS hard drive options for Video Recording, Data RAID Level: 0, 1, 5, 6, 10. NIC card 4 x 1GbE supporting network throughput of 800 MBPS, Graphics Adapter - Intel® HD Graphics 1GPBS, Windows Server 2016 R2 64-bit/Windows 10 64-Bit Operating System, Microsoft SQL Server/Express 2016. Recording to be concidered for 30 days at 2MP, 25 FPS in RAID 5.

Server for VMS software - Server PC with minimum Intel® Six Core Xeon E5 2530V2 2.6 GHz S1150, Dual NIC 1GBPS, OS in RAID-1, Microsoft Windows® 2012/2014/2016 Server STD 64-bit, Dual power supply, 16 GB RAM, DVD +/- RW, Two separate hard drives 1TB Each 10K RPM SATA.

Client Workstation - Supply, installation, testing & commissioning of Client Workstation as per following specifications:Intel Core i7-7700K, 4.2GHz, OS - Genuine Microsoft Microsoft® Windows 10 Enterprise 64 Bit, RAM - 16GB, Memory - 500 GB HDD Graphic Card - In-built Processor Graphics (GPU):Intel® HD Graphics 630 and NVIDIA Quadro NVS 315 1 GB PCIE x 16 LP supporting 2/4 Monitors., Two(2) PCI-Express Expansion Slots 2/4 USB, 2 serial, and 2 HDMI/VGA Adaptor, CD/DVD ROM.; USB Keyboard and Mouse, UPS, associated cables etc complete As per tender document.

"Supply, installation, testing & commissioning with proper connection & termination of following size equipment rack made out of CRCA sheet to house all the control equipment complete as required in accordance with laid specification or upto the satisfaction of engineer in charge. " 19" equipment rack -6 U

"Supply, installation, testing & commissioning with proper connection & termination of following size equipment rack made out of CRCA sheet to house all the control equipment complete as required in accordance with laid specification or upto the satisfaction of engineer in charge. " 19" equipment rack -42U

Supply, installation, testing and commissioning of Layer-3 Distribution Switch 24 Gigabit Ports, Rack Mountable, 4 Port SFP+ 10GpE, including Fibre module for LAN base feature set with support to integration with CCTV, with all related hardware complete as required and as per specifications

Supply, installation, testing and commissioning of Layer-2 PoE Distribution Switch 24 Gigabit Ports, Rack Mountable, 4 Port SFP+ 10GpE, POE+ Switch including Fibre module for LAN base feature set with support to integration with CCTV, with all related hardware complete as required and as per specifications

Supply installation, testing and commissioning of Desktop Computer comprising CPU, Keyboard and a mouse complete with operating system (OS) and other required software to control NVR in control room including Centralized Video Management Software as per the requirement of the successful operation of the surveillance system complete as required in accordance with laid specification or upto the satisfaction of engineer in charge.

Supply & laying of following Cables for CCTV's signal/power including cable gland and other required accessories shall be laid in existing conduit/cable tray etc. complete as required in accordance with laid specification or upto the satisfaction of engineer in charge. Cat 6 , 4 pair UTP cable (1 BOX= 305 Mtr)

Supply, installation, testing & commissioning of Information outlet Cat 6 Blue

Supply, installation, testing & commissioning of Mounting Cord Cat6( 1) Mtr- Blue

Supply, installation, testing & commissioning of 20 MM Faxibale Conduit

Supply, installation, testing & commissioning of 20MM PVC Conduit

Junction BOX

Camera Mounting Accessories (11 feet to 25 feet)

2U wire manager with cover

6 Core multimode fiber cable along with LIU, Patch panel, etc complete with all accessories

"EPBAX WORKS Passive Cabling System" Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable 305 mtr per Box. Blue in colour conforming to the following standards like ANSI/TIA 568 C.2, EN50173, IEC 11801 2nd ED, 700Mhz etc. in Cat 6 U/UTP LCS2 cable with 23AWG.

Supplying, installing, testing and commissioning of Cat 6 , Tool less Information outlet for Data,Voice,CCTV,Wi-Fi, & Access Control. Cat6 U/UTP built in crimping hands-free, minimum 5 times reconnection possibilities. LCS2 Toolless RJ45 Information outlet where insertion test (in & out) must be 2500 times (I/O) along with front side Label holded and transparent shutter for projection Arteor category white in colour, including front plate and anodised GI box in concealed manner of adequate sizes,including all fixing accessories.

Supplying, installing, testing and commissioning of following length of Cat - 6 patch cord. 4 Feet : CAT6 UTP 23 AWG Patch Cord - 1 mtr - Rack End. Factory crimped LCS2 Patch cord in Blue colour.

Supplying, installing, testing and commissioning of following length of Cat - 6 patch cord. 7 Feet : CAT6 UTP 23 AWG Patch Cord - 2 mtr - User End.Factory crimped LCS2 Patch cord in Blue colour.

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block.

Supplying and fixing following cover plate on existing modular metal boxes etc. as required,1 or 2 Module Face Plate

Supplying, laying and fixing of 6 core Corrugated Steel Tape OM3 Multimode Optical Fiber of size 50/125μm LSZH. Indoor/Outdoor Universal loose tube Black Jacket through existing GI/HDPE/ Hume pipe or on cable trays inside the cable duct including all necessary fixing accessories e.g. cable ties, hardware etc. Standard & Approval : EN 50173-1 : 2002, IEC 60794-1, ISO 11801 2nd ED

Supplying, installing, testing and commissioning of 10 GB - 50/125μm OM3 LC Pigtails MM 50/125mn.

Supplying, installing, testing and commissioning of 6 port LCS2 Adapter plate, loaded with 3 nos. of duplex LC unit for 6 multi mode fibers of size 50/125 μm .Adapters to be compatible to fit in 19" U/UTP 24 port modular patch panel or 24 port LIU.

Supplying, installing, testing and commissioning of LIU 24 port LC type LCS2. Rack Mount 19" modular type unloaded to be compatible for 4nos of 6 X RJ 45 UTP unit in a block or 6 port SC/LC/ST adapter unit. Material of LIU is Galvanised Steel and Weight is approx 2.605 kg.

Supplying, installing, testing and commissioning of MM Patch Cord -LC/LC Duplex Cords - 2 mtrs.

Supplying, installing, testing and commissioning of 42U Cabinet. Size 2026 X 800 X 800 mm (HXWXD) following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt (kg) 150, CRCA 'D' Grade thickness (mm) 1.2, RAL 9017(Matt Black), Glass: 4mm Toughened Tinted Glass Door, Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C 90 CFM) - 4 Nos, Cable Manager Metal- 4 Nos, PDU 230VAC - 1 No (12 nos. 6A/16A sockets with plugs 6A/16A - 1/1pc & MCB 16A/32A - 0/1 Pc), Cable Channel 100mm wide 42U- 2 Nos, Heavy Duty Stationary Shelf 600mmW x 475mmD - 1 No., Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 3 Nos., Earthling Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor Wheels (without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP foam. In the rack there must be maintained 1 U = 1.75 inches space. Nos. 1

Supplying, installing, testing and commissioning of 15U Wall-mounting cabinets. size 771.35X600X500mm (HXWXD)) with all standard accessories. Width (mm) 600, Depth (mm) - 500, Approx.Net Wt (kg) - 32, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal - 3 Nos, Earthling Strips 150mm H - 1 No, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space. Nos. 20

Supply, Installation, testing and commissioning of 1 U Horizontal Wire Manager 60mm depth (Front Side)

ACTIVE COMPONENTS Supplying Installation testing and Commissioning of Switch with at least 48 X SFP+ 10G Ports and additional 6 X QSFP+ 40G Ports, with non-blocking architecture, 250K+ MAC table , Switch should support ACL, QOS, OSPF, 802.1x, VXLAN, ONIE / OpenFlow v1.3, Data Center Bridging Exchange (DCBX) 802.1Qau, 802.1Qbb and 802.1Qaz, Certification: CE, FCC, BSMI, CB and UL. Should support two AC/DC hot-swappable internal power modules for 1+1 redundancy and load sharing. OEM should available in Gartner Magic Quadrant for Wired and Wireless LAN Access Infrastructure Report from latest last three consecutive year.

Supplying Installation testing and Commissioning of Direct Attached Cable Pluggable 10 Gigabit Ethernet (SFP+) SR Optics.

Supplying Installation testing and Commissioning of 10GBASE-LR SFP+ Transceiver, Fiber Module should be Hot Pluggable, MSA Compliant and RoHS Compliant, Module should support 10KM Distance, Fiber module should be same of Switch OEM,

Supply, Installation, Testing & Commissioning of Switch with at least 24 X 10/100/1000BASE-T Ports and 2 x 10G Base-T and 4 X SFP+ Ports, Switching capacity should be 168 Gbps, Switch should support 16 L3 IP interfaces, ACL, QOS, VRRPv3, Equal-Cost Multi-Path (ECMP) , UDP helper, Policy-based Route (PBR), 802.1x, Embedded 6 kV surge protection on ethernet ports, Switch should have console port, RJ45 Management Port and USB port, Should support internal/external redudent power supply for 1+1 redundancy and load sharing. Certification: CE, FCC, BSMI, CB and UL. OEM should available in Gartner Magic Quadrant for Wired and Wireless LAN Access Infrastructure Report from latest last three consecutive year.

Supply, Installation, Testing & Commissioning of Switch with at least 24 X 10/100/1000BASE-T POE+ Ports and 2 x 10G Base-T and 4 X SFP+ Ports, Switching capacity should be 168 Gbps, Switch should support 16 L3 IP interfaces, ACL, QOS, VRRPv3, Equal-Cost Multi-Path (ECMP) , UDP helper, Policy-based Route (PBR), 802.1x, Embedded 6 kV surge protection on ethernet ports, Switch should have console port, RJ45 Management Port and USB port, Should support internal/external redudent power supply for 1+1 redundancy and load sharing. Certification: CE, FCC, BSMI, CB and UL. OEM should available in Gartner Magic Quadrant for Wired and Wireless LAN Access Infrastructure Report from latest last three consecutive year.

Supply, installation, testing & commissioning of Dual-band 802.11abgn/ac Wireless Access Point, 3x3:3 streams, dual ports, 802.3af PoE support. Does not include power adapter or PoE injector.should Includes Warranty and Mounting Kit complet in all respect.

EPABX System Supply Installation, Testing and Commissioning of Server Based EPABX Fully Computerized IP System, SIP Compliant. 2U Rack Mountable,Expandable upto 2000Ports.and configured as for below Ports P & T(CO Trunk) Line 08 Nos. PRI(30 Channel) 1 Nos. IPExtension Circuit 08 Nos. Digital Extension Circuit 16 Nos Analog Extension Circuit 50 Nos

Supply Installation and Commissioning of centralized Operator Console with all dignostic Software of IP EPABX System

Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level IVR software with 6 different languages and 4 time schedule(As per OEM).

Supply Installation Testing and Commissioning of Digital Phone 32Key Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface .

Supply Installation Testing and Commissioning of 24Key Digital Phone Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface.

Supply Installation Testing and Commissioning of Digital Phone (12Key)Backlit keypad Hands-free, full duplex Headset support Easy to use soft keys/LCD prompts Directory dialling Navigation wheel Call history , Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface.

Supply Installation Testing and Commissioning of Digital Phone (6Key)Backlit keypad Hands-free, full duplex Headset support Easy to use soft keys/LCD prompts Directory dialling Navigation wheel Call history , Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface.

Supply Installation Testing and Commissioning of IP Phone (12Key)Backlit keypad Hands-free, full duplex Headset support Easy to use soft keys/LCD prompts Directory dialling Navigation wheel Call history , Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface.

Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight.

"LAN (LOCAL AREA NETWORK) WORKS LAN/ UTP based data cum voice points/Fibre for back bone and related accessories " CAT6 U/UTP: Supplying and drawing CAT6 U/UTP Cable,Performance Characters - Category 6 EIA/TIA 568.C.2 (23AWG), (LSZH) Low smoke zero halogen and Product should UL listed / ETL Verified in the existing surface/ recessed Steel/ PVC conduit as required. With an industry standard assumption of 35 Meter per node (total nodes 2500), (Make: Molex, Panduit, RiT) Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

12F Single mode Fiber: Supplying of Outdoor Unitube Single Sheathed Armoured with Steel Wire for network backbone across various buildings and periphery of the campus, underground in the open areas or inside PVC conduit as required. (Make: Molex, Panduit, RiT)

Installation/Laying of fiber Fiber Trunching & Laying With HDPE 32 mm Dia ,Chamber ,Route Marker & HDD wherever applicable

Information Outlet: SITC of CAT6 UTP Information Outlets with SMB/ Face Plate including Gang Box,RJ45 Jack should be supplied with Shutter/Cap to avoid Dust and Product should UL listed / ETL Verified (Make: Molex, Panduit, RiT)

Patch Panel: SITC of CAT6 UTP 24 Ports Jack Panel Loaded, Height 1 U, Material of Patch Panel: Cold rolled steel, Modular plug fitting (RJ 45): Individual ports should be supplied with Shutter/Cap to avoid Dust and Information Outlets should UL listed / ETL Verified (Make: Molex, Panduit, RiT)

Cable Manager, Dynamic/Dlink

1 Mt Patch Cord (Rack end SITC of CAT6 U/UTP Mounting Cord 1 Mtr., Patch cord Sheath:: LSZH,Conductor size:24 AWG stranded copper wire and Product should UL listed / ETL Verified (Make: Molex, Panduit, RiT)

3 Mt Patch Cord (User end) SITC of CAT6 U/UTP Mounting Cord 3 Mtr., Patch cord Sheath:: LSZH,Conductor size:24 AWG stranded copper wire and Product should UL listed / ETL Verified (Make: Molex, Panduit, RiT)

LIU 12 Port SM Fully Loaded: SITC of Lockable 19" rack mounted with 1U height,LIU 12 Port SM fibre Sliding enclosure with Splice Tray,Adapter plate SC Type,The enclosure/LIU should have locks to secure all the fiber terminations.Material type-Powder coated Mild Steel (Make: Molex, Panduit, RiT)

LIU 96 Coret SM: SITC of 96 Core Fully Loaded Lockable 19" rack mounted with 1U height,LIU 12 Port SM fibre Sliding enclosure with Splice Tray,Adapter plate SC Type,The enclosure/LIU should have locks to secure all the fiber terminations.Material type-Powder coated Mild Steel (Make: Molex, Panduit, RiT)

SFP Patch Cord SM:SITC of SC-SC 9/125, SM, 3 Mtr Patchcord,Cable Sheath-LSZH, Polishing-100% Factory polished, tested and Guaranteed Performance Standartds-ROHS Compliant (Make: Molex, Panduit, RiT)

RACK 9U: Supply and Fixing 9U Rack ,Network Cabinet High Quality Wall Mount Rack ,Steel Body with Glass door ,Lock &key with fitting and Installation. (Make:Comrack/Dynamic)

RACK 12U: Supply and Fixing 12U Rack ,Network Cabinet High Quality Wall Mount Rack ,Steel Body with Glass door ,Lock &key with fitting and Installation. (Make: Comerack/Dynamic)

RACK 42U: Supplying and istallation and commissioning of 42 U 800*1000 closed Network rack Supports/hanging arrangement (Make -Comerack/Dynamic)

Supply of 1 KVA Online UPS with 30 Minute Battery backup 1kVA/0.8kW 1-Phase Input / 1-Phase Output a) True Online configuration with double conversion UPS & Zero transfer time. b) Wide Input voltage range from (110 ~ 300VAC) d) Auto restart & capability with the Independent battery bank operation of the UPS. e) UPS should be designed at Rated PF of 0.8 i.e. 1kVA/0.8kW UPS rating. f) Generator compatibility with cold start and AC start features. g) Automatic bypass to transfer the load on mains due to overload & internal fault. h) ECO mode should be available in the UPS. Single-Phase / 2-Wire & Gnd (1Phase & Neutral + Ground) 110-300VAC Range (Full Load) 160~300VAC Range (60 ~ 100% load is required) 110~160VAC 50 or 60Hz 40 to 70 Hz > 0.99(@ full load)Compatibility to genset supply required Should be provided at the input of the UPS suitable for the full rated capacity of the UPS. 200/208/220/230/240 VAC ± 1% for static load 50 or 60Hz ±3Hz ± 0.1Hz < 1Hz/sec Pure sine wave < 3% for linear load & < 6% for non-linear load. ( Make-Numeric/Delta)

Access Switch: With 24 port with 1G uplinks 56Gbps/ 83 Mpps, 2 GB RAM and 4 GB Flash, 16K MAC Addresses and 1024 active Vlans Switch should have slot/ports(excluding uplinks) for minimum 80 Gbps of stacking bandwidth with dedicated stacking ports and cables with minimum 8 switch in stack Switch should be able to support 3000 IPV4 & 1500 IPV6 routing entries (Make: Cisco/Extreme/Juniper)

L3 Switch: Switch should be 1RU with minimum 24 no. of 10/100/1000 POE+ ports with additional 4 nos. of 10 Gig, Switch should have minimum 320 Gbps of stacking bandwidth with dedicated stacking ports and cables with minimum 4 switches in a single stack from Day 1.Should have 8 GB RAM and 16 GB Flash (Make: Cisco/Extreme/Juniper)

Core Switch: The Switch should have minimum 24x 1/10/25G Ports for the downlink connectivity and at least 4x 40/100G Uplink ports for uplink connections and future use, Should have internal Redundant Power supply from Day 1 Should have at least 16 GB DRAM & 12GB Flash memory (Make: Cisco/Extreme/Juniper)

Supplying Installation testing and Commissioning of 10GBASE SFP+ Transceiver, Fiber Module should be Hot Pluggable, MSA Compliant and RoHS Compliant, Module should support 10KM Distance, Fiber module should be same of Switch OEM,

Access Point: Access Points proposed must include radios for 2.4 GHz and 5 GHz with 802.11ac Wave 2. Access Point shall support Console port that uses Standard Port (RJ-45) type connection, Should have one RJ-45 auto-sensing 10/100/1000 Mbps LAN port.Must support 3x3 MIMO for both 802.11ac and 802.11n client, Must support minimum of 22dbm of transmit power in both 2.4Ghz and 5Ghz radios. And should follow the local regulatory Norms.Make: Cisco / Brocade /HP

Wireless Controller: Must be compliant with IEEE CAPWAPor equivalent for controller-based WLANs. Should have atleast 1 x MultiGigabit/ 10 gigabit Ethernet interface aloong with 4x100/1000 RJ45 Baste-T ports.Should support both centralized as well as distributed traffic forwarding architecture with L3 roaming support from day 1. Should have IPv6 ready from day one. (Make: Cisco/Brocade/HP)

NGFW (next generation Firewall): The appliance based security platform should provide firewall, AVC and IPS functionality in a single appliance from day one, The appliance should support atleast 6 * 10G Gigabit ports and should be scalable to additional 8 * 40G in future Proposed Firewall should not be proprietary ASIC based in nature & should be open architecture based on multi-core cpu's to protect & scale against dynamic latest security threats.

A/VC (Audio Video Conference): The solution should be a web based tool allowing users to connect with other users over Internet/ Secure Intranet. The tool should enhance individual and team productivity and collaboration with high-quality audio, video, and web conferencing, The tool should enable mobile users to be more productive and be engaged with the ability to participate in meetings using a variety of mobile devices such as smartphones, tablets, iphone

End Points (VC Devices): Must support IPv4 and IPv6 from day one. Must have the following physical buttons for ease of use1. Mute/ Unmute 2. Volume Increase/ decrease, Should be an integrated system with at least 22 to 24 inch LCD/TFT screen,1080P resolution (16:9), HD camera and with speakers for wide band audio output. The Codec should be a part of the unit. No separate Codec's are preferred. The LCD/TFT screen should be a touch screen to provide a touch interface to the user.

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 400-450 CFM / 0.80-0.82 TR

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 400-450 CFM / 1.0-1.02 TR

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 500-512 CFM / 1.28-1.30 TR

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 750-777 CFM / 1.55-1.60 TR

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 820-830 CFM / 2.0-2.02 TR

"INDOOR UNITS Supply, installation, testing and commissioning of following Wall Mounted /Cassette type units with panel and inbuilt drain pump/slim Ceiling Mounted duct type/Ceiling Mounted Built in type/Ceiling Mounted Ductable type units VRF Air Conditioners with cordless/corded remote controller.Fully Factory assembled,wired and tested Indoor Units as per specifications ans as required to make the system complete. Aluminum fins within the IDU (evaporator unit) shall be coated with polysiloxane based coating Ceiling Mounted Cassette Unit " 1150-1175 CFM / 3.0-3.2 TR

Wall Mounted 660-671 CFM/1.98-2.01 TR (With Sequencing Controler 4+4)

Ceiling Mounted Ductable Unit 850-890 CFM / 2.5-2.55 TR

Floor Mounted AHU 3000 CFM , 6.0 TR, 6- Row Deep 2 nos. cooling coil (DX Cooling Coils), 125 mm Static Pressure, with pre & Fine ,ESP filter (Hepa on Terminal) ,Mixing Box and with three phase motor with weather proof canopy.

Accessories SITC of Control cum Expansion Kit Required for the above AHU to make the system complete

REMOTE CONTROLLERS Supply, installation, tesing and commissioning of Imported Remote controllers (Corded) for operation of ductable indoor units and AHU's.

Touch screen controller for indoor units controller - VRV Supply, installation, testing and commissioning of touch screen controller (Which is controlled 45 nos. indoor units in terms of ON/Off Status, temp. Status, Fan Speed, ODU On/Off Status etc.) with all accessories and controls.

REFNUTS / Y-JOINTS Supply, installation, tesing and commissioning of Imported fittings Y-joints insulated, distributer and headers for all Indoor units at both the ends floors layout as per layout drawings.

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 06.35 mm with 13 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 09.52 mm with 13 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 12.70 mm with 13 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 15.88 mm with 13 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 19.05 mm with 13 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 22.22 mm with 19 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 28.58 mm with 19 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 34.92 mm with 19 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"REFRIGERANT PIPING Supply, installation, testing and commissioning of Interconnecting refrigerant pipe work with (13/ 19mm thick) Nitrile Rubber/cross linked closed cell Oxide Acetate Foam tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with hangers and  All interconnecting Copper piping, joints, U bends with polysiloxane based coating shall run in cable tray. (Note: Ref. Piping Length may be review as per site routing)" 41.30 mm with 19 mm thick nitrile rubber/cross linked closed cell Oxide Acetate Foam insulation

"TRANSMISSION & CONTROL WIRING Supply, installation, testing, termination and commissioning of control cum transimission wiring (should be shielded cable in PVC Pipe) of 2C x 1.5 Sqmm Cu between indoor unit and out door unit and indoor units and its remote controller." 2C x 1.5 Sqmm Cu Cable or as per Manufacturer OEM

Perforated GI Tray with hangers & supports for copper piping (250 mm wide)

Refrigerant-410a Supply , charging & Leackage testing of refrigerant -410a in additional copper piping circuit.

"Air Cooled Hi-Wall Split units Providing and fixing of Air Cooled Split airconditioners each comprising an outdoor unit consisting of hermetic Invertor scroll compressor, air cooled condensing unit, Condenser fan etc. with outer casing and indoor fan coil unit(s) consisting of centrifugal fans, fan motor, DX cooling coil, outer casing, filter, control and power panel with corded/cordless remote control, stablizer etc. both inter connected with copper refrigerant pipe (Compressor capable Approx. 30-40 mtr. copper piping) and drain pipe of required length as given, cabling and wiring, insulation with cross linked polyethelene foam, full charge of refrigerant gas and oil, M.S. base frame, supports etc. complete as per specifications and drawings. The cost shall also include angle iron stands for outdoor units . If A common Servo oil type stablizer than not required stablizer. "2.0 TR Hi-wall Unit with ref.circuit and approx 30-40 meter of ref.and drain piping & Cabling with sequencing controller (1 Working + 1 Standby) as per specifications & Drawing, For Server/UPS & Battery Room

SITC of Automatic Voltage stabilizer complete with HI-LOW voltage cut out , TDR and Power wiring from Stabilizer to Unit as per the design & specifications and approval / instruction of the consultant - 5KVA

Supply, Installation, Testing and Commissioning of Control cum Transmission wiring(4C x1.5sqmm.) in suitable conduits between indoor & outdoor units including supply of screened wires, supports, installation , saddles, ties, tags, ferrules, lugs, nuts/bolts/hardware etc. complete in all respects as per specifications and any other item required to make the system complete.

SITC of Interconnected Copper Piping (Soft/Hard both) (1/2", 1 1/8",5/8",7/8",9/8")For Cassette/Split Air conditioners, the piping duly insulated with Nitrile insulation tubes of respective sizes and control cabling from Indoor to Outdoor units.

SITC of Power Cabling / Wiring of Condensing Units of Split Air-conditioners- from Isolators to Condensing Units, including supply of all materials complete in all respects as per specifications and any other item required to make the system complete. 3Cx2.5 Sqmm.

"Air Purifier (PHI Cell) (Optional) Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on advanced oxidation technology with broad spectrum UV lamp (100-380 NM) enhanced on the quad metallic compound target/ hydrated catalytic matrix cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial, viral and spores contamination and VoC’ and odors. The UV lamp must be enclosed in a poly casing to prevent mercury at all cost.Refer technical specififcations for more details and complinace." 300 CFM to1200 CFM AHU/Indoor

"Air Purifier (PHI Cell) (Optional) Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on advanced oxidation technology with broad spectrum UV lamp (100-380 NM) enhanced on the quad metallic compound target/ hydrated catalytic matrix cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial, viral and spores contamination and VoC’ and odors. The UV lamp must be enclosed in a poly casing to prevent mercury at all cost.Refer technical specififcations for more details and complinace." 1250 CFM to 3000 CFM AHU/Indoor

"Air Purifier (PHI Cell) (Optional) Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on advanced oxidation technology with broad spectrum UV lamp (100-380 NM) enhanced on the quad metallic compound target/ hydrated catalytic matrix cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial, viral and spores contamination and VoC’ and odors. The UV lamp must be enclosed in a poly casing to prevent mercury at all cost.Refer technical specififcations for more details and complinace." 3500 CFM to 5000 CFM AHU/Indoor

"Air Purifier (PHI Cell) (Optional) Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on advanced oxidation technology with broad spectrum UV lamp (100-380 NM) enhanced on the quad metallic compound target/ hydrated catalytic matrix cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial, viral and spores contamination and VoC’ and odors. The UV lamp must be enclosed in a poly casing to prevent mercury at all cost.Refer technical specififcations for more details and complinace." 5100 CFM to 10000 CFM AHU/Indoor

"Air Purifier (PHI Cell) (Optional) Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on advanced oxidation technology with broad spectrum UV lamp (100-380 NM) enhanced on the quad metallic compound target/ hydrated catalytic matrix cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial, viral and spores contamination and VoC’ and odors. The UV lamp must be enclosed in a poly casing to prevent mercury at all cost.Refer technical specififcations for more details and complinace." 10001 CFM to 17000 CFM AHU/Indoor

"Air Purifier (ESP Filters) (Optional) Supply, installation, testing and commissioning of Electronic air cleaner system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technology which consists filteration -firstly a washable aluminium prefilter which filters upto 10 microns, followed by a washable Electrostatic precipitation section (consisting of tungsten wires for ionizing and aluminium collector plates) Other forms of air filtration systems such as charged media filters, dielectric media filters, or ionizers (which do not have second stage collector plates) shall not be acceptable. The average capacity of the EAC shall be at least 1,700 CMH for the single cell unit and 3,400 CMH for the double cells unit. It should be a monobloc structured unit specifically designed for integration in Return Air path of the AHU, to centrally capture the pollutants. It should be equivalent to MERV14 efficiency @ 1708 cfm with low pressure drop of not more than 75Pa @ 492fpm (as per ASHRAE 52.2-2012). It should be UL Listed with in built provision to connect to BMS. The product has to be certified as a green product by IGBC . Ozone level of units provided must be within the acceptable limit of 0.05ppm. The units shall have local LEDs at each individual unit to indicate when the units are up for wash/malfunctioning. Efficiency in reducing micro - organisms to be above 85% and needs to be supported by a test report from a reputed lab., AHU mounted air purification system with ESP Filters" 1000 CFM to3000 CFM AHU/Indoor

"Air Purifier (ESP Filters) (Optional) Supply, installation, testing and commissioning of Electronic air cleaner system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technology which consists filteration -firstly a washable aluminium prefilter which filters upto 10 microns, followed by a washable Electrostatic precipitation section (consisting of tungsten wires for ionizing and aluminium collector plates) Other forms of air filtration systems such as charged media filters, dielectric media filters, or ionizers (which do not have second stage collector plates) shall not be acceptable. The average capacity of the EAC shall be at least 1,700 CMH for the single cell unit and 3,400 CMH for the double cells unit. It should be a monobloc structured unit specifically designed for integration in Return Air path of the AHU, to centrally capture the pollutants. It should be equivalent to MERV14 efficiency @ 1708 cfm with low pressure drop of not more than 75Pa @ 492fpm (as per ASHRAE 52.2-2012). It should be UL Listed with in built provision to connect to BMS. The product has to be certified as a green product by IGBC . Ozone level of units provided must be within the acceptable limit of 0.05ppm. The units shall have local LEDs at each individual unit to indicate when the units are up for wash/malfunctioning. Efficiency in reducing micro - organisms to be above 85% and needs to be supported by a test report from a reputed lab., AHU mounted air purification system with ESP Filters" 3500 CFM to5000 CFM AHU/Indoor

"Air Purifier (ESP Filters) (Optional) Supply, installation, testing and commissioning of Electronic air cleaner system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technology which consists filteration -firstly a washable aluminium prefilter which filters upto 10 microns, followed by a washable Electrostatic precipitation section (consisting of tungsten wires for ionizing and aluminium collector plates) Other forms of air filtration systems such as charged media filters, dielectric media filters, or ionizers (which do not have second stage collector plates) shall not be acceptable. The average capacity of the EAC shall be at least 1,700 CMH for the single cell unit and 3,400 CMH for the double cells unit. It should be a monobloc structured unit specifically designed for integration in Return Air path of the AHU, to centrally capture the pollutants. It should be equivalent to MERV14 efficiency @ 1708 cfm with low pressure drop of not more than 75Pa @ 492fpm (as per ASHRAE 52.2-2012). It should be UL Listed with in built provision to connect to BMS. The product has to be certified as a green product by IGBC . Ozone level of units provided must be within the acceptable limit of 0.05ppm. The units shall have local LEDs at each individual unit to indicate when the units are up for wash/malfunctioning. Efficiency in reducing micro - organisms to be above 85% and needs to be supported by a test report from a reputed lab., AHU mounted air purification system with ESP Filters" 5500 CFM to 8500 CFM AHU/Indoor

"Air Purifier (ESP Filters) (Optional) Supply, installation, testing and commissioning of Electronic air cleaner system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technology which consists filteration -firstly a washable aluminium prefilter which filters upto 10 microns, followed by a washable Electrostatic precipitation section (consisting of tungsten wires for ionizing and aluminium collector plates) Other forms of air filtration systems such as charged media filters, dielectric media filters, or ionizers (which do not have second stage collector plates) shall not be acceptable. The average capacity of the EAC shall be at least 1,700 CMH for the single cell unit and 3,400 CMH for the double cells unit. It should be a monobloc structured unit specifically designed for integration in Return Air path of the AHU, to centrally capture the pollutants. It should be equivalent to MERV14 efficiency @ 1708 cfm with low pressure drop of not more than 75Pa @ 492fpm (as per ASHRAE 52.2-2012). It should be UL Listed with in built provision to connect to BMS. The product has to be certified as a green product by IGBC . Ozone level of units provided must be within the acceptable limit of 0.05ppm. The units shall have local LEDs at each individual unit to indicate when the units are up for wash/malfunctioning. Efficiency in reducing micro - organisms to be above 85% and needs to be supported by a test report from a reputed lab., AHU mounted air purification system with ESP Filters" 9000 CFM to 12500 CFM AHU/Indoor

"Air Purifier (ESP Filters) (Optional) Supply, installation, testing and commissioning of Electronic air cleaner system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technology which consists filteration -firstly a washable aluminium prefilter which filters upto 10 microns, followed by a washable Electrostatic precipitation section (consisting of tungsten wires for ionizing and aluminium collector plates) Other forms of air filtration systems such as charged media filters, dielectric media filters, or ionizers (which do not have second stage collector plates) shall not be acceptable. The average capacity of the EAC shall be at least 1,700 CMH for the single cell unit and 3,400 CMH for the double cells unit. It should be a monobloc structured unit specifically designed for integration in Return Air path of the AHU, to centrally capture the pollutants. It should be equivalent to MERV14 efficiency @ 1708 cfm with low pressure drop of not more than 75Pa @ 492fpm (as per ASHRAE 52.2-2012). It should be UL Listed with in built provision to connect to BMS. The product has to be certified as a green product by IGBC . Ozone level of units provided must be within the acceptable limit of 0.05ppm. The units shall have local LEDs at each individual unit to indicate when the units are up for wash/malfunctioning. Efficiency in reducing micro - organisms to be above 85% and needs to be supported by a test report from a reputed lab., AHU mounted air purification system with ESP Filters" 13000 CFM to 17000 CFM AHU/Indoor

"DRAIN PIPING Providing & fixing rigid PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation." 25 mm dia

"DRAIN PIPING Providing & fixing rigid PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation." 32 mm dia

"DRAIN PIPING Providing & fixing rigid PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation." 40 mm dia

"DRAIN PIPING Providing & fixing rigid PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation." 50 mm dia

"AIR DIFFERENTIAL PRESSURE SWITCH Supply,install,test and commission Air Differential pressure switches complete with sensor probe , etc. integrated with Light and visual alarm signal, as per general details and specifications and approved make.To be installed across HEPA filter bank sections and Operating rooms.The necessary control and power wiring shall be in the scope of the contractor." Air Differential Pressure Switch. ( ACROSS OT rooms.)

CANVASS CONNECTION Supply,Installation,Testing and commissioning of doble layer canvas connection with fire rating.

"Ventilation System Ventilation Equipments: Propeller fan Supply,installation,testing and commissioning of Propeller fan of the following capacity of approved make and specification. Fan shall be supplied with aluminum gravity louver & bird screen." 150 mm dia propeller fan, with single phase motor

"Ventilation System Ventilation Equipments: Propeller fan Supply,installation,testing and commissioning of Propeller fan of the following capacity of approved make and specification. Fan shall be supplied with aluminum gravity louver & bird screen." 300 mm dia propeller fan, with single phase motor

"Ventilation System Ventilation Equipments: Propeller fan Supply,installation,testing and commissioning of Propeller fan of the following capacity of approved make and specification. Fan shall be supplied with aluminum gravity louver & bird screen." 450 mm dia propeller fan , with single phase motor

"Inline fan Supply, installation, testing and commissioning of AMCA Certified circular type Inline fan of the following capacity of approved make and specification. (Cost to be inclusive of Speed Regulator) Fan shall be supplied with aluminum gravity louver & bird screen." 100 to 300 CFM, 5-7mm SP WG with Single phase motor with three speed

"Inline fan Supply, installation, testing and commissioning of AMCA Certified circular type Inline fan of the following capacity of approved make and specification. (Cost to be inclusive of Speed Regulator) Fan shall be supplied with aluminum gravity louver & bird screen." 450 to 800 CFM, 7-10 mm SP WG with Single phase motor with three speed

"Inline fan Supply, installation, testing and commissioning of AMCA Certified circular type Inline fan of the following capacity of approved make and specification. (Cost to be inclusive of Speed Regulator) Fan shall be supplied with aluminum gravity louver & bird screen." 850 to 1100 CFM, 12-15mm SP WG with Single phase motor with three speed

"Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 3500-5500 CFM smoke extract

"Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 6500-10500 CFM smoke extract

"Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 13000-16000 CFM smoke extract

"Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 24000 CFM smoke extract

"Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 1000-3000 CFM smoke extract

"SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `F' insulation. Fan efficiency should not be less than 70 %, noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions. Fans should be as per specification and drawings. (As per Vent. Fan Schedule ) (Makeup Air & Pressurization Fans with St. Press. of 40 mmWG/Make Up Air Fan at 30mm WG)Tube Axial Flow fans SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet and fire retardent flexible connections at inlet/outlet. The electric motor coupler shall be squirrel cage induction motor (IE-2 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance ""Class H Smoke Spill"" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). Normal/Smoke Exhaust fans at St. Press. of 30 mmWG" 6500-7500 CFM for Liftwell pressurization, 40 mm S.P.

"Evaporative air cooler(Air Washer) Supply , Install, test and commission double skin Evaporative air washer as per specifications , suitable for the following capacity given below at 90% efficiency of evaporative medium. The fan shall be of DIDW centrifugal construction. Packaged Type" 2500 CFM, 40 mm (WG) static pressure,Floor/ ceiling mounted (For Kitchen ),Cost to be inclusive of unit isolator

Air Scrubber (DRY Type) DIDW FAN :Kitchen Exhaust "" Supply, installation, testing and commissioning of DIDW Backword curved horizontal floor mounted fan unit comprising of accurately cut scroll & side plates, heavy gauge with all welded construction, sheet steel fabricated impeller, drive with blower pulley, motor pulley, V-belts, squirrel cage motor complete as per specification (fan-motor efficiency exceeding ASHRAE 90.1-2007 Criteria). (The bidder shall submit fan performance curves for all fans)." The item should be all complete in line with relevant standards, technical specifications of the standards and direction of engineer incharge.3000 CFM / 75 mm WG SP (For Kitchen ),Cost to be inclusive of unit isolator

DRY SCRUBBER : Kitchen Exhaust Supply, Installation, Testing and Commissioning of Dry Scrubber comprising of extract air intake section, electrostatic precipitation technology, dry type air cleaner to remove odour, smoke and fumes from exhaust air. "" Electrostatic section shall be made of 16 gauge galvanised sheet,high bake epoxy powder coated, washable type aluminium mesh filters, stainless steel spiked ionizers to create high voltage DC field, Stainless Steel 316 collector plates which should be alternatively charged positive and negative with large collecting area with 14"" deep cell, to work as magnet for charged smoke and oil particles. Average efficiency of 95% and more in single pass as per DOP test method. Electrostatic Precipitator should be able to charge particles from 0.01 micron to 10 microns through solid state power supply. The system should be fitted with interlock switch for safety. The system should allow connection to a fan section to achieve 500 FPM velocity across the air cleaner. 3000 CFM / 75 mm WG SP (For Kitchen ),Cost to be inclusive of unit isolator

"AIR CURTAIN Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make and with Door limit switch/sensor with multi speed regulator .(At ground entrance)" 2100 mm long (High flow type)

"AIR CURTAIN Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make and with Door limit switch/sensor with multi speed regulator .(At ground entrance)" 1500 mm long (High flow type)

AIR DISTRIBUTION SYSTEM Site Fabricated Duct - GI Sheet Metal duct"" Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 0.63mm (24 gauge) GSS

AIR DISTRIBUTION SYSTEM Site Fabricated Duct - GI Sheet Metal duct"" Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 0.8 mm (22 gauge) GSS

AIR DISTRIBUTION SYSTEM Site Fabricated Duct - GI Sheet Metal duct"" Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 1.0mm (20 gauge) GSS

AIR DISTRIBUTION SYSTEM Site Fabricated Duct - GI Sheet Metal duct"" Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 1.25mm (18 gauge) GSS

"Factory Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of factory fabricated GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 0.63mm (24 gauge) GSS

"Factory Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of factory fabricated GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 0.8 mm (22 gauge) GSS

"Factory Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of factory fabricated GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, Gripple supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces." 1.0mm (20 gauge) GSS

"Site Fabricated Duct - AL duct 'Supply,Installation,balancing and commissioning of fabricated at site Al. sheet metal ducts in accordance with the approved shop floor drawings and specifications , and shall also confirm to the BIS specifications. The hardware shall be chrome plated or of stainless steel.All lateral and transverse joints shall be sealed with silicon based mastic sealant." Aluminum Sheet thickness - 1.00 mm

Supply, Fabrication, Installation and testing of Insulated Al. Flexible ducts in accordance with the approved shop floor drawings and specifications and shall also confirm to the BIS specifications. 200 mm Dia.

Supply, Fabrication, Installation and testing of Insulated Al. Flexible ducts in accordance with the approved shop floor drawings and specifications and shall also confirm to the BIS specifications. 150 mm Dia.

"Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings." Aluminium supply air grilles with damper.

"Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings." Aluminium return air grilles without damper.

"Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings." Aluminium supply air square diffuser with damper

"Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings." Aluminium return/exhaust air square diffuser without damper.

Aluminium return/exhaust air Valve circular/squirell diffuser without damper.

Linear air grilles (150 MM wide)

Aluminium supply air collar damper

AI Volume control dampers for ducts

"Fresh Air/Exhaust Air Louvers Supplying and fixing of extruded aluminium louvres with frame bird screeen , mounting arrangement etc. as per specifications and drawings." Fresh Air/Exhaust Louvers

Supply,installation,testing and commissioning of factory fabricated and insulated (with self adhesive XLPE / Nitrile rubber foam) square (595 mm x 595 mm) laminar air flow plenum with diffusion plates , volume control device and openable perforated sheet with 50% free area,suitable to be mounted in the standard grid ceiling all duly fabricated in aluminum and powder coated, as per specifications, If at site no Moduler OT Than its used.

Supply,installation,testing and commissioning of HEPA filters of 610x610mm x 155 thick as per specifications and drawings duly sealed with Epoxy and DOP tested. HEPA filters as mentioned above for Up to 550 CFM handling capacity for Terminals in OT's

"MOTORIZED FIRE AND SMOKE DAMPERS Supplying, fixing, Testing and commissioning of fire dampers in suppy air duct/main branch and return air path as and where required of required size i/c control wiring ,the damper shall be motorized combination fire and smoke damper (spring return type) of approved make of atleast 120 minute fire rating and as per the specifications as detailed earlier in the relevant sections.The fire damper shall be complete with electronic temperature sensor and electrically operated actuator .The fire dampers shall be located in the supply/return air ducts, at all fire rated crossovers (shafts/walls etc.) The control panel will be such located that the reset can be easily done These combination smoke and fire dampers shall be interlocked with the building management system for fire detection / HVAC and shall trip/close in the event of fire / smoke in the respective zone ." Bare Fire Dampers with 400 mm sleeve

Control panel actuator , including Electrical,spring type actuator,remote indication of the fire damper position.

Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers.

Sealing the openings around the sleeve of the fire dampers with approved fire sealant, as per the recommendations of the manufacturer and specifications.

Supply,Installation,Testing and commissioning of doble layer canvas connection with 1/2 hr. fire rating as per specification.

NSULATION WORKS THERMAL INSULATION:"" SITC of Thermal insulation material for Duct insulation shall be closed cell cross linked polyethylene foam. Thermal conductivity of the insulation material shall not exceed 0.032 W/moK at an average temperature of 25oC. Density of the material shall be 25-30 Kg/m3. The product shall have temperature range of –40 oC to 105oC. The insulation material shall be fire rated for Class 1 as per BS 476 Part 6: 1989 for fire propagation test and as per BS 476 Part 7, 1987 for surface spread of flame test. Water vapour permeability as per DIN 52615 shall not exceed 0.15ng/Pa.Sec.m. " 32 mm thick insulation with 2 layesr coat 7 mile cloth insulation or starbond insulation(for exposed duct)

INSULATION WORKS THERMAL INSULATION:"" SITC of Thermal insulation material for Duct insulation shall be closed cell cross linked polyethylene foam. Thermal conductivity of the insulation material shall not exceed 0.032 W/moK at an average temperature of 25oC. Density of the material shall be 25-30 Kg/m3. The product shall have temperature range of –40 oC to 105oC. The insulation material shall be fire rated for Class 1 as per BS 476 Part 6: 1989 for fire propagation test and as per BS 476 Part 7, 1987 for surface spread of flame test. Water vapour permeability as per DIN 52615 shall not exceed 0.15ng/Pa.Sec.m. " 13 mm thick insulation(Supply Air Ducts in NON AC Area)

INSULATION WORKS THERMAL INSULATION:"" SITC of Thermal insulation material for Duct insulation shall be closed cell cross linked polyethylene foam. Thermal conductivity of the insulation material shall not exceed 0.032 W/moK at an average temperature of 25oC. Density of the material shall be 25-30 Kg/m3. The product shall have temperature range of –40 oC to 105oC. The insulation material shall be fire rated for Class 1 as per BS 476 Part 6: 1989 for fire propagation test and as per BS 476 Part 7, 1987 for surface spread of flame test. Water vapour permeability as per DIN 52615 shall not exceed 0.15ng/Pa.Sec.m. " 9 mm thick insulation(Supply Air Duct)

ACOUSTIC LINING IN THE SUPPLY/RETURN DUCTSSupply and Application of acoustic lining within the supply air duct Nitrile Rubber/Insusound material as per specifications and drawings.15mm thick (For Duct)

ACOUSTIC LINING IN THE SUPPLY/RETURN DUCTSSupply and Application of acoustic lining within the supply air duct Nitrile Rubber/Insusound material as per specifications and drawings.25mm thick (For AHU)

"Exposed Roof Insulation Supply,application of under deck insulation of roof exposed to direct sun , with Thermal insulation material for Under-deck insulation shall be closed cell cross linked polyethylene foam. Thermal conductivity of the insulation material shall not exceed 0.032 W/moK at an average temperature of 25°C. Density of the material shall be 25-30 Kg/m3. The product shall have temperature range of –40 °C to 105°C. The insulation material shall be fire rated for Class 1 as per BS 476 Part 6: 1989 for fire propagation test and as per BS 476 Part 7, 1987 for surface spread of flame test. Water vapour permeability as per DIN 52615 shall not exceed 0.15ng/Pa.Sec.m. "13 mm thick Under deck insulation as per the specifications detailed above in the section

ASSOCIATED ELECTRICAL WORKS The rates for the distribution boards from the Breakers and instruments shall also include the following :Wiring for light / Fan points with 1.5 sq. mm PVC insulated copper conductor 1100 Volt grade stranded flexible FRLS wires of approved make in 1.6 mm thick 25 mm dia MS conduit including cost of providing & fixing saddles, hangers, supports, cutting chases and filling chases for recessed conduiting, and including the cost of providing and fixing a 6 amp 240 Volt Modular Plate type switches of approved quality, colour, make and design with moulded cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sq. mm PVC insulated copper earth wire for loop earthing etc. complete "TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link." All MCB’s shall be of minimum 10 KA breaking capacity and MCCB 's shall be not lessthan 25KA "The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic microprocessor releases as per BOQ and following :" i. MCCB rating upto 250 Amps with thermal magnetic releases. ii. MCCB above 250 Amps with microprocessor releases. "All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic." "Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993." i. IP 42 for indoor panels. ii. IP 55 for ODU panel. "All MCCB’s shall be provided with operating mechanism for door interlock." "All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire." "Providing cable clamps / supports within distribution boards cable alley."

"Current density of aluminium shall be 1sq mm for 1.0 Amps for rated current of bus bars." "Model, current capacity location and frame size of switchgear shall be written inside of the panel doors with paint / permanent marker as approved shop drawings / site requirment." All meter shall be digital type and all starter shall be as per Type-2 Coordination chart Current Transfomer shall be resin cast. All Panel Shall be BMS Compitable AHU/Fan Panel Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of following LT panels fabricated out of 14 guage CRCA sheet steel in cubical formationwith reinforecment of suitable size angle iron and channel T iron flats. All steel material used in the construction of panels shall be powder coated. A solid busbar shall be provided at the bottom of the panel with two connecting eyes for termination. The boards shall be suitable for 415 volts, 50 Hz, 3 phase , 4 wire supply system. All the hardware used in the fabrication of the panel shall be galvanized with zinc passivation. The panel shall be compartmentalized to accommodate one feeder in each compartment. A vertcal cable alley of suitable width shall be provided to serve on or two vertical feeder sections. Also the opening between the busbar chamber and the feeder section shall be shrouded with bakelite / hylam sheet with min.3 mm thickness. The panel drawing shall be approved before taking up the fabrication and compitable BMS if in future required. In All panel Each starter should have remote control and interlocking facilities including auto manual switch, NO/NC contacts for control and must have auto manual operation suitable to take signal from fire alarm panel for automatic operation of fan in case of fire. All smoke /vent. fan panel the starters shall have suitable facility to operate with fire sensing control modules. HVAC AHU Panel MCC-I,II,VIIIaType (0 +1 Nos.) Incoming/Outgoing 1 no. 2.5-4 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC AHU Panel MCC-III Type (2 Nos.) Incoming/Outgoing 1 no. 4-6.3 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC AHU Panel MCC-IV Type (4 Nos.) Incoming/Outgoing 1 no. 6-10 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC AHU Panel MCC-V Type (1 Nos.) Incoming/Outgoing 1 no. 13-18 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC AHU Panel MCC-VI Type (2 Nos.) Incoming/Outgoing 1 no. 9-14 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC AHU Panel MCC-VIa Incoming 1 no. 50 amp MCB Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. Bus Bars 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. Outgoings 1 no. 6-10 A, TP MPCB (with VFD) 1 no. 9-14 A, TP MPCB (with VFD) 1 no. 6 A TP MCB The base frame shall be 75 mm x 5 mm. Panel as described above and in drawings.

HVAC AHU Panel MCC-VIb Incoming 1 no. 32 amp MCB Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. Bus Bars 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. Outgoings 1 no. 4-6.3 A, TP MPCB (with VFD) 1 no. 20 A TP MCB 1 no. 6 A TP MCB The base frame shall be 75 mm x 5 mm. Panel as described above and in drawings.

HVAC Fan Panel MCC-VII Type (4 Nos.) Incoming/Outgoing 1 no. 6-10 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC Fan Panel MCC-VIII Type (1 Nos.) Incoming/Outgoing 1 no. 4-6.3 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC Fan Panel MCC-IX Type (5 Nos.) Incoming/Outgoing 1 no. 9-14 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC Fan Panel MCC-X Type (1 Nos.) Incoming/Outgoing 1 no. 13-18 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

HVAC Fan Panel MCC-XI Type (1 Nos.) Incoming 1 no. 20 amp MCB Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. Bus Bars 32 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. Outgoings 1 nos. 2.5-4 A,TP MPCB (with DOL starter ) 1 nos. 4-6.3 A,TP MPCB (with DOL starter ) The base frame shall be 75 mm x 5 mm. Panel as described above and in drawings.

HVAC Pressurization Fan Panel MCC-XII (3Nos.) Incoming 1 no. 50 amp MCB Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. Bus Bars 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. Outgoings 2 nos. 6-10 A,TP MPCB (with DOL starter ) The base frame shall be 75 mm x 5 mm. Panel as described above and in drawings.

HVAC AHU Panel MCC-VI c Incoming 1 no. 32 amp MCB Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. Bus Bars 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. Outgoings 1 no. 6-10 A, TP MPCB (with VFD) 1 no. 20 A TP MCB 1 no. 6 A TP MCB The base frame shall be 75 mm x 5 mm. Panel as described above and in drawings.

HVAC Fan Panel MCC-VIIIb Type (2 Nos.) Incoming/Outgoing 1 no. 1.6-2.5 A, TP MPCB (with DOL starter ) Phase indicating lights with control fuses. Breaker ON/OFF/TRIP indicating lights. The base frame shall be 75 mm x 5 mm. (Optional) Panel as described above and in drawings.

CABLING (POWER )Power Cabling and Earthing:vSupply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed/XLPE Insulation, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc. 3Cx04 Sqmm

CABLING (POWER )Power Cabling and Earthing:vSupply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed/XLPE Insulation, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc. 3Cx06 Sqmm

CABLING (POWER )Power Cabling and Earthing:vSupply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed/XLPE Insulation, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc. 4Cx06 Sqmm Cu

CABLING (POWER )Power Cabling and Earthing:vSupply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed/XLPE Insulation, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc. 4Cx04 Sqmm Cu

CABLING (POWER )Power Cabling and Earthing:vSupply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed/XLPE Insulation, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc. 2Cx04 Sqmm Cu

Control Cabling Supply, installation, testing & commisioning of Copper conductor , PVC insulated, PVC sheathed /XLPE armoured cable of 1.1 KV grade (Which is Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers & Touch screen controller ). 8C x 1.5 Sqmm

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required. 3Cx04 Sqmm

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required. 3Cx06 Sqmm

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required. 4Cx06 Sqmm

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required. 4Cx04 Sqmm

Supplying and installing following size of perforated G.I. cable trays, G.I. bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with suitable suspenders including G.I. bolts & nuts, painting of suspenders etc. complete as required. 100 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supplying and installing following size of perforated G.I. cable trays, G.I. bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with suitable suspenders including G.I. bolts & nuts, painting of suspenders etc. complete as required. 150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supplying and installing following size of perforated G.I. cable trays, G.I. bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with suitable suspenders including G.I. bolts & nuts, painting of suspenders etc. complete as required. 225 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Providing and fixing following size of G.I. wire on surface or in recess for loop earthing alongwith the existing surface/ recessed conduit/ submain wiring / on cable tray/ on surface including G.I. clamps etc. complete as required. 6 SWG G.I. wire

NCS (NURSE CALLING SYSTEM) "Medi Alert" NURSE CALL SYSTEM "MAKE M-LINE" :- Providing & Supply of Nurse Call System display window with Soft Touch Keypad, Voice Module, Power Supply, Nursing Supervisory Controller. The Nurse Call System cover is made using high quality. CE & ISO Mark Central Module

Bed Side Module (Wired Communication)

Door Indicator (Wired Communication)

Toilet Switch (Wired Communication)

AUDIO-VIDEO SYSTEM FOR LECTURE THEATERS A - Smart Classroom Supply, Installation, Testing and Commissioning of true diversity Wireless Microphone with Frequency response: 50 to 16,000 Hz, THD: ≤ 0.9%, Pick- up pattern: Omni-directional, Signal-to-noise ratio: ≥ 103 dBA, RF output power: 10 mW, Switching bandwidth: up to 24 MHz, Modulation: Wideband FM, 12 compatible channels.

Supply, Installation, testing and commissioning of Goosneck Microphone of 12" to 16" with Polar Pattern : Cardioid, Frequency Response : 50 - 20,000 Hz complete with shock mount.

Supply, Installation, testing and commissioning of Modular DSP with 4 x mic/line input, 2 x line outpt, AEC for future expansion, Processor: 40-bit floating point, Sampling Rate: 48kHz, A/D-D/A Converters: 32-bit, THD+N: 0.002%, Dynamic Range: 110dB, Crosstalk: <110 dB alongwith built-in 4x4 Dante/AES67 audio.

Supply, Installation, testing and commissioning of Two way Wall mount Loudspeaker with Frequency Response: 75 Hz - 18 kHz, Frequency Range: 60 Hz - 20 kHz: Nominal Dispersion: 180° H x 75° V, Overload Protection Lamp, Long-Term Power Handling: 100 W, Sensitivity: 85 dB SPL, Maximum SPL: 111 dB SPL, LF: 1 x 5", 2 x 2.5" HF driver.

Supply, Installation, testing and commissioning of Dual Channel power share amplifier with Power: 2 x 300 W @ 4-8 Ω, 70/100V, THD+N: <0.04%, Frequency response: 20 Hz – 20 kHz, Channel Separation (Crosstalk): > 85 dB, Signal to Noise Ratio: 100 dB, A/D and D/A Converters: 24-bit / 48 kHz.

Supply, Installation, testing and commissioning of 2 core 1.5 sqmm PVC insulated Cu conduction loudspeaker Cable. (Approved Makes: Krystal, Klotz, Sommer)

Supply, Installation, testing and commissioning of 2 core shielded PVC insulated microphone Cable.

Supply, Installation, Testing and Commissioning of minimum 6000 ANSI Lumens, WUXGA, Single Chip Laser DLP Projector, Native 16:10, Display: 1 x 0.67” DMD, Contrast ratio: 300,000:1, Resolution :Up to 1,920 x 1,200, inputs: 2 x HDMI, 1x DVI-D, 1 x HDBaseT, 1 x VGA, Signal outputs: 1 x VGA, Pixel clock: 162MHz, Control port: RS232, HDBaseT, Ethernet, IR, 20,000 hours life along with 24 /7 operation, complete as required.

Supply, Installation, Testing and Commissioning of 137" motorized tab tensioned projection screen with Aspect ratio: 16:10, IR & RF remote control.

Supply, Installation, Testing and Commissioning of Mettalic Podium with Interactive 21" or higher Tablet Monitor, Desktop PC with i5 processor, 4GB RAM, 1TB hard disk with Presentation Plate, document camera and provision to place Switcher, Amplifier, PC, etc complete with standard accessories, complete as required.

Supply, Installation, Testing and Commissioning of Presentation Switcher/Scaler with HDBaseT & HDMI Simultaneous Outputs, 4 x HDMI, 2 x VGA input, 1 x HDMi and 1 x HDBaseT output.

Supply, Installation, Testing and Commissioning of 4K60 Twisted Pair receiver with 1x HDBaseT input, Output: 1 x HDMI, Should support resolution of 4K or more, Bidirection RS-232 and IR control, HDMI 2.0 and HDCP 2.2 Support, complete as required.

Supply, Installation, Testing and Commissioning of 8 Button Panel with Controller with 2 x RS-232 port, 1 x RS-485, 2 x Relay, IR and ethernet port.

Supply, Installation, Testing and Commissioning of 2mtr. HDMI-HDMI Cable.

Supply, Installation, Testing and Commissioning of 4 pair Shielded Cat5/6 Cable.

ONLINE TEACHING STUDIOS Supply, Installation, testing and commissioning of Goosneck Microphone of 12" to 16" with Polar Pattern : Cardioid, Frequency Response : 50 - 20,000 Hz complete with shock mount.

Supply, Installation, testing and commissioning of Modular DSP with 4 x mic/line input, 2 x line outpt, AEC on each input, 2x2 USB for soft VC application, Processor: 40-bit floating point, Sampling Rate: 48kHz, A/D- D/A Converters: 32-bit, THD+N: 0.002%, Dynamic Range: 110dB, Crosstalk: <110 dB alongwith built-in 4x4 Dante/AES67 audio.

Supply, installation, testing and commissining of 75" interactive board with UHD resolution, Multi writing up to 10 on any background for optimized classroom engagement, 20 pages of writing space per roll, allowing users to seamlessly scroll through pages, gives users the capability to open Microsoft Word, PowerPoint, Excel and Adobe PDF files directly with a built in document viewer, secure content protection by 6 digit lock, IR Touch, 2 x 10 watt built in speaker, Input: 2 x HDMI, 1 x DP, 3 x USB, 1 x HDMI output, 2 x Touch out.

Supply, Installation, Testing and Commissioning of 21.5" interactive monitor with Resolution: Full HD, 1,920 x 1,080 pixels, Viewing angles: 178 x 178 degree, Brightness: 210 cd/m2, Contrast ratio 800:1, Colors: 16.7M colors, Video connection: VGA / DVI, 2 x USB interfaces.

Supply, Installation, Testing and Commissioning of Desktop PC with i5 intel processor, 4 GB RAM, 1 TB Hard disk, antivirus along with wireless keyboard and mouse. (Approved Makes: HP, Dell, Lenovo )

Supply, Installation, Testing and Commissioning of Video Soundbar USB conferencing device with array microphone having Static and adaptive dynamic beam-forming, 3 exclusion zones, Stereo acoustic echo cancellation, Noise suppression, Supported resolutions: UHD 2160p (4K); 1080p, 720p, 960x480, 848x480, 640x480, 640x360, 432x240 (30 fps), 2 x 20 Watt Stereo loudspeakers, Input/Output ports: 1 x USB-C 3.0, 1 x USB-A 3.0, 1 x HDMI 1.4 out, 1 x Analog audio input (stereo, 3.5 mm), 1 x Gbps Ethernet, RJ-45, Built-in camera with 120° FOV diagonal, 109° FOV horizontal, 67° FOV vertical, 8 megapixel sensor, 4K resolution, Auto white balance, Auto brightness, Digital noise reduction, Easily connect a smartphone via Bluetooth connectivity to use as a standalone speakerphone or stream music.

Supplying, installation, testing and commissioning of Recording & streaming Switcher with 4 SDI, 2 x HDMI video input, 1 x HD-SDI, 2 x HDMI digital video output, Chroma key, PinP (Picture in Picture), nsert and overlay titles, Overlay Logo, Stream content live over the internet, Record direct to SD memory card.

Supply, Installation, Testing and Commissioning of 8 Button Panel with Controller with 2 x RS-232 port, 1 x RS-485, 2 x Relay, IR and ethernet port.

Supply, Installation, Testing and Commissioning of Cables and connectors.

LIFTS 20 PASSENGER LIFT, SPEED- 1 MPS (No. of floors / Stops/ opening 4/4/4) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

LIFTS 20 PASSENGER LIFT, SPEED- 1.5 MPS (No. of floors / Stops/ opening 4/4/4) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

LIFTS 13 PASSENGER LIFT, SPEED- 1.5 MPS (No. of floors / Stops/ opening 7/7/7) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

LIFTS 10 PASSENGER LIFT, SPEED- 1.5 MPS (No. of floors / Stops/ opening 3/3/3) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

LIFTS 10 PASSENGER LIFT, SPEED- 1.5 MPS (No. of floors / Stops/ opening 7/7/7) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

LIFTS 10 PASSENGER LIFT, SPEED- 1.5 MPS (No. of floors / Stops/ opening 6/6/6) 1- Battery Operated Emergency Light and Alarm Bell. 2-Call Register Signal and Vf door operator. 3- False Ceiling in Car. 4-Automatic Rescue Device. 5- Overload Warning Indicator. 6- Firemans Switch. 7- Floor Annunciator. 8- Free Service for one Year. 9- Infra Red Door Screen. 10- Ss Handrail. 11- Full Car Operation Panel. 12- 3 Way Intercom / Press and Speak Phone. 13- Push Button Orange LED Illumination. 14- Dot matrix Led D & P indicators in Car & landings orange colour. 15- Pit ladder. 16-Landing push button in landing door frames. 17- Stainless steel braille button with S.S. cover. 18- Minor builders work. 19- Scaffolding. 20-Sill Support. 21- Lift License. 22- Fire rating of landing doors one hour.

NKG Infrastructure Limited