Providing CAD works to LIS 5 No. Panchayat (Sandhole, Neri, Datwar and Ghanalla) in Tehsil Sandhole District Mandi (HP)

Amount

Civil Work :- Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work, blasting work, chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed in all leads including lifts and soring/strutting timbering and dewatering where ever required as per thr direction and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size ) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying cement concrete 1:3:6 (1 cement: 3 sand: 6 graded crushed stone agg. 40mm nominal size) and curing complete excluding cost of form work in:- Foundation and plinth upto all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge.

Providing & Laying cement concrete work 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation footing bases of columns etc and mass concrete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Column, pillar, posts and struts upto floor two level as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumers and cantilever upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Stair cases (Except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Walls any thickness but not less than 0.1m thickness including attached pillaster buttresses, plinth and string courses from top of foundation upto two level all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Arches upto floor two level in all leads and lifts as per direction and to the entiresatisfaction of Engineer-in-charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu- reinforcement concrete and plain concrete work in:-

Foundation footing bases of columns etc and mass concrete complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like, Floors etc. up to any thickness complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns, pillars, post and struts, Square, rectangular or polygonal in plan complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Stair cases with sloping or stepped soffits excluding landings.

Beam, cantilever, girders and lintels, Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Edges of slabs and breaks in floors and walls under 20cm wide complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Vertical surfaces such as wall (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work of ordinary timber plankings so as to give a rough finish including centring, shuttering, strutting & propping etc. height of propping & centring below supporting floor to ceilling not exceeding 4 mts. And removal of the same for insitu-reinforced concrete and plain concrete work in :

Arches beyond 6.00 mtrs span as per direction and to the entire satisfaction of Engineer-in-charge.

Providing RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement :3 sand) and curing complete in all lead and lifts as per direction and to the entire satisfaction of the Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40mm nominal size)curing complete excluding cost of form work in foundation and plinth as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work in

Foundation footing bases of columns etc and mass concrete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing mild steel / Tor steel reinforcement for RCC work including bending binding and placing in position complete upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Brick work using common burunt clay building bricks in foundation anf plinthl in cement mortor 1:6 (1 cement : 6 sand) (2nd class brick) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Half brick masonry in common burnt clay 2nd class building bricks in superstructure above plinth level upto floor two level in cement mortar1:4 (1 cement :4 sand) as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (2nd class deodar wood) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (2nd class deodar wood) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing wire gauge shutters using galvenised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors, windows & clearstory windows i/c bright finished black iron enamelled hinges with necessary screws 40 mm thick (2nd class deodar wood) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Provdiing and laying 20 cm thick composit stone masonry with stone masonry with stone facing of chisel dressed stone one line dressed in cement mortar 1:6 (1 cement :snnd) and concrete backing with cement concrete 1:3:6 (1cement :3and :6 graded stone aggregate 20 mm norinal size) on inner face of walls including cenrting shuttering and propping complte upto floor two level.

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement: 6 sand) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

20 mm thick cement plaster with cement mortar 1:4(1 cement; 4 sand) in single coat on rough side of brick/concrete/stone walls for interior plastering all heights including arises, internal rounded angles chamfers and/ or rounded angles in all girth and finished even and smooth i) Upto all floor levels

Cement concrets flooring 1:2:4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement (40 mm thick) as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lift.

Cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1:Cement 3:Sand) finished with a floating coat of neat cement including rounding of junction with floor 20mm thick complete as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lift.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete 40 mm Thick as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying spartic ceremic tiles 9mm.thick in flooring (600 x600mm. size)treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement:3 sand) finished with flush pointing in white cement including carriage of material in all leads & lifts.

White glazed tiles 9 mm thick in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3sand) finished with flush pointing in white cement complete in all respect including carriage of material in all leads & lifts. (size of tile=30x45cms)

Providing and Fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & Fixing with nails & screws etc. complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 19mm thick Commercial Board water proof shutters for up boards i/c Fixing with nickel plated piano hinges with screws etc. complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing 6mm thick burl ply of standard quality and of approved shade & design wall lining i/c fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately) complete in all respect including carriage of material in all leads & lifts

Providing and fixing stainless steel stands for base of cabinets 7x7cms and 10 cms high,fixed wioth screwswithin all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge

Providing and fixing square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete in all respect including carriage of material in all leads & lifts. 2nd class deodar wood within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing bright finished brass sliding door-bolts with nuts and screws etc. complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing bright finished brass handles for doors with screws etc. complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished hard down Hooks and Eyes 150 mm with screws etc. within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished brass Godrej make mortie lock with all acessories within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing Heavy duty hydraulic door closer Godrej makewithin all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth ( under Floor) complete in all respect including carriage of materials in all leads and lifts as per direction and to the entire satiafaction of the Engineer-in- charge in all lead and lifts.

Providing 40x3 mm iron hold fast 40 cm long including Fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Steel work welded in built up section, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paintin grating, framed guard bars ladders, railing brackets and similar works as per direction of Engineer-in-Charge upto all lead and lift.

Miscellanious for locking arrengements & other accessories as per direction of Engineer-in-Charge upto all lead and lift.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees including carriage of material in all leads and lifts as required as per the direction of Engineer-in-charge

Providing & fixing ridges or hips 60 cm overall with 0.60 mm Thick pre-painted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns primer coating i/c fixing with prepainted iron J or L-hooks bolts & nuts 6 mm dia with prepainted G.I. limpet and bitumen washer complete with all accessories as required as per direction and to the entire satisfaciton of Engineer-in-charge.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying cement concrete 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40mm nominal size) with 15% Plum and curing complete excluding cost of form work in retainin walls/breast walls, the size of plums shall usually by 150mm to 300mm as per HPPWD specification as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing bright finished brass handles for cup board with screws etc. complete. in all respect including carriage of material in all leads & lifts 150 mm as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing 15 cm. wide 45 cm. overall semi circular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design including carriage of material in all leads & lifts as required as per direction and to the entire satisfaciton of Engineer-in-charge. 0.63mm thick sheet.

Construction course rubble hammer dressed U shap open surface drain with side wall 15x22 cm in cement motor 1:6 (1 cement:6 sand) and in side plastering with cement plaster 1:3(1cement:3 sand) including earth work and laying 10 cm cement concrete 1:5:10 (1cement:5sand:10 graded stone agg. 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1cement:2sand:4 graded stone agg. 40 mm nominal size) and finished with a floating coat of neat cement complete as standred design.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete .

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete complete in all respect including carriage of material in all leads & liftss as per direction and to the entire satisfaction of the Engineer in Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Polishing two coats with PU(poly utherene) polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Applying one coat for wood preservetive on previously treated wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter,sand papering and knotting complete in all respect including carriage of material in all leads & lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge.

Painting two coats (excluding priming coat) over new steel and other metal surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing plaster of paris(POP) false ceiling 12 mm thickplaster, fixed over GI sections and wire mesh, L-connectors, rawl plugs, complete as per Arhitectural drawings complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge.

Providing and laying heavy duty precast cement concrete inter locking paver blocks 60mm thick with chamferred edge vibro completed up to M-50 grade of NTC or equivalent make i/c border or kurb block gray or coloured over sub-base of concrete with 25 mm thick average thickness of cement mortar 1:4 (1 cement, 4 Sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete in all leads and lift as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 6/8 mm thick window glasses, for fixed portion of windows, with teak wood beading/moulding 40x12mm, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing stainless steel railing for stairs using 304 grade,Jindel coil, top hand rail 50 mm diameter@ 1.85kg/mtr,50x40mm square balusters fixed at alternate step, 4 nos 20x20mm horizontal sq.pipes welded to balusters, balusters fixed to steps by drilling in tread and fixing of 16mm, bolt 50 mm long and washers complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Provisions for furniture for all floors/Rooms except kitchen items( Sofa 1 & 3 seater, MEETING CHAIRS,Centre table 3x3 & 4x2 feet, Side table 18"x18", Dining table 8 seater, Double bed 70"x75",Easy chairs with arms,centre table 42x21" Study chair, Balcony chairs, Matress 75x35x5.5"thk & 75x35x4" Pillow, Bed side runner mat,Centre carpet for vip 6x4feet, Foot mat small, Main ent. Foot mat 4x3feet,Quilt double bed & single bed, Blanket double bed & single bed, Dhortfor summer) d/bed,VIP bed cover set, Dining table mats, Bath towel, Hand towel,Curtains. 220cm-length, Room Piller heater Set of bath bucket, Patra,Soap dish,Mug And toilet brush,harpik etc,Dust bin padel type operation, Cup board hangers,LED TV 42" Drg+bed,Table lamp for VIP Wall paintings 3x2 feet, Flower pots, Portable Plastic chairs, for cleaning as per the entire satisfaction of Enginner in Charge within all leads & lifts. (Kindly refer data sheet No. I)

Provisions for crockery items for kitchen All items of crockery, utensils, of superior class including Refrigerator 350 Water purifier (UV), LPG Stove with 4 burner,LPG Connection, Pressure cooker 3,5 & 10 ltrs, Supply of Induction cooker (plate) Supply of Miser (MIX) and all other cooking items of approved make should be provided in kitchen. (Kindly refer data sheet No. II)

Provision for structural design and drawing (after acertaining the safe bearing capapcity of the soil at site) the architecture drawing of all the buildings and all other components. The structural design & drawing for all the structures duly vetted from PEC Chandigarh/NIT Hamirpur shall be submitted by the contractor for approval of the Department before start of work.

Laying, jointing & testing of G.I pipe of following dia (light class) for outlets pipe & scour pipes etc. in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge. (Labour rate)

100 mm dia

Laying, jointing and testing in trenches (to level or grade) of following dia Medium Class GMS pipes plain ended jointed with every fifth joint flanged & remaining butt weld joints with of below diametre conforming to IS 1239-1990 (Part - I ) with latest upto date amendments of grade and wall thickness as specified below, suitable to withstand required hydraulic test pressure in randum length 4m-6m with plain ends and jointed with butt welding with electrodes as per IS 814-1991. The welding of joint to be done to make the joints leak proof (Earth work to be mearsured and paid separately) and to entire satisfaction of the Engineer-in-Charge.The laying of pipes conform to IS 5822-1994 and as per CPHEEO manual and will include all operations such as cutting, welding and jointing including flushing, cleaning and hydraulic testing complete in all respect. (L.R.)

100mm dia Medium Class

80mm dia Medium Class

65mm dia Medium Class

Providing and fixing double flanged Cast Iron sluice valve of following dia of Kirloskar/Leader/RG/LP/Kartar/Suchdeva or any other approved make conforming to IS:14846/2000 with up to date amendment as per Class PN-1 to withstand in normal seat pressure including welding with M.S. flanges table as per IS 6392-1971 including carriage in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

100mm dia Medium Class

80mm dia Medium Class

65mm dia Medium Class

Providing and fixing Manhole cover of size 60x60 cm made of angle iron frame size 40x40x5mm thick covered with M.S. sheet 2.00mm thick and welded with angle iron frame 35x35x3mm thick including hings, handles, 8 Nos hold fast and locking arrangement along with lock and key of standred make primer two coat with redoxide paint complete and manhole cover fixed in storage tank/intake with cement concrete 1:1.5:3, nut & bolt and dismentalling of RCC work complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia. & 180 mm deep(inside) with chained lid RCC top 1:2:4 mix (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) 100 mm thick foundation concrete 1:5:10 mix (1 cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1 :3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside syze With 150 mm thick walls of RCC 1:2 :4 (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways.

Providing and fixing steel fibre reinforced concrete (SFRC) Manhole covers and frame confirming to IS : 12592 (part-I) 1988 with latest ammendments extra heavy should not be less than 100Kg, circular 560mm dia meter as per direction and to the entire satisfaction of Engineer-in-Charge.

Laying jointing and commissioning of HDPE (High Density Polyethlene pipe) of following diameter and class confirming to IS 4984-1995 with fusion welding process including all necessary fitting & bend leads and lifts to the entire satisfaction of Engineer-in-charge (earth work in ternches to be mesured and paid separately)

HDPE pipe 75 mm dia PN 6 PE- 80 (Labour Rate)

HDPE pipe 75 mm dia PN 8 PE- 80 (Labour Rate)

HDPE pipe 75 mm dia PN 10 PE- 80 (Labour Rate)

HDPE pipe 75 mm dia PN 12.50 PE- 80 (Labour Rate)

HDPE pipe 140 mm dia PN 6 PE- 80 (Labour Rate)

Fitting and accessories.

75 mm dia PN-4.0, 5.0, 6.0, 8.0 HDPE pipes. (Labour Rate)

75 mm dia PN-6 pipe end

75 mm dia PN-6 HDPE 90° bends with rotating clamp

75 mm dia PN-6 HDPE QC connector

WATER SUPPLY AND SANITARY:- Providing and fixing high pressure spigot and socket waste ventilating pipe of following daimeter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC plain bend of following diameter i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

75mm dia

100mm dia

Providing and fixing PVC door bend of following diameter i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

75mm dia

100mm dia

Providing and fixing PVC collar/ socket of following diameter i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach of following diameter i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach with eval access of following diameter i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

75mm dia

100mm dia

Providing and fixing PVC Floor traps 110x75mm i/c entire carriage of material within all leads and lifts of Finolex/Diplast Make.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral “P”or”S” trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement: 1 sand) including entire carriage of material within all leads and lifts.

Single piece WC i/c seat cover ,wall distance 300mm.

P/F 10 litres vitrous china with low level flushing cistern with a pair of CI or mild steel brackets, comp. with fitting such as lead valve less syphon 15mm normal size brass ball valve with polythene float CP brass handle union & couplings for connections with inlet, outlet & overflow pipe 40mm dia CP flush beng i/c cutting holes in walls & making good the same & connecting the flush bend with cistern & closet (over flow pipe to be measured & paid for separately).

Two piece WC .wall distance 300 mm

Providing and fixing Plastic seat cover i/c entire carriage of material within all leads and lifts.

Providing and fixing vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white i/c cutting holes & making good the same but excluding fitting i/c entire carriage of material within all leads and lifts. Cera make Concord, 630x450mm size.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for the reception of pipes and fitting i/c entire carriage of material within all leads and lifts.

Providing and fixing of MI union for wash basin 32mm dia i/c carriage of material within all leads and lifts.

Providing and fixing 32mm dia PVC waste pipes for wash basin i/c brass check nut i/c entire carriage of material within all leads and lifts.

Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts.

Providing and fixing C.P. brass towel rail complete with C.P.brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts 600 x 20mm.

Providing and fixing 600x120mm glass shelf i/c entire carriage of material within all leads and lifts.

Providing and fixing CP toilet paper holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass soap dish i/c entire carriage of material within all leads and lifts.

Providing and fixing Tooth brush and tumbler holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass shower 250mm dia,with 60 cms long rod, i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap long nose 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap short body 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.

Providing and fixing brass angle valve 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing CP concealed stop cock 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing single hole single lever wash basin mixture i/c entire carriage of material within all leads and lifts.

Providing and fixing PVC connection 15mm dia i/c entire carriage of material within all leads and lifts.

Providing and fixing 100mm dia, C.P. brass grating including carriage of material within all leads and lifts.

Providing and fixing Jet connection ,health facut ,fixed for WC seat i/c entire carriage of material within all leads and lifts.

Providing and fixing CP towel ring i/c entire carriage of material within all leads and lifts.

Providing and fixing CP towel rack 600x250mm for VIP toilet i/c entire carriage of material within all leads and lifts.

Providing and fixing wall to ceiling and floor galvanised mild steel tubes light grade), tube fittings and clamps i/c making good wall ceiling & floor of following diameter i/c entire carriage of material within all leads and lifts

15mm dia

20mm dia

32mm dia

Providing & fixing Brass full way wheel valve i/c entire carriage of material within all leads & lifts

20mm dia

32mm dia

Providing and fixing 115x50x25cms size double bowl of approved make stainless steel kitchen sink i/c entire carriage of material within all leads and lifts

Providing and fixing 2000 ltrs. Double layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lefts.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement :2 sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 ( 1cement:4sand :8graded stone aggregate 20 mm nominal size),inside plastering 15 mm thick with cement mortor 1:3 (1cement:3sand),finished with a floating coat of neat cement & making channels in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) finished smooth complete i/c curing &testing. (i) inside size 1200 x 900 x 1000 mm deep i/c c.i. cover with frame (m. duty) with single pattern 455 x 610 mm internal dimensions (total wt.of cover & frame to be not less than 38 kg) 23 cms. thick brick masonry walls using 2nd class brick in cm 1:3 (icement : 3 sand)

Providing & fixing stone ware gully trap grade 'A' complete with CI grating,B/Masonry chamber in cement mortor 1:5 & water tight CI cover with frame of 300 mm x 300 mm size (inside) .The wt.of cover to be not less than 4.53 Kg & frame to be not less 2.72 Kg. (Square mouth traps 100 x 100 mm size)

Electrical Items:- Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group "C"

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & Fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules (140mmx78mmx50mm)

6 modules (205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

2 x 4.00 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch.

6 pin,15/16 Amps Modular socket outlet.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

TV. Socket outlet, modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

Telephone socket outlet, Modular.

Supplying and Fixing ceiling rose on the existing junction box / wooden block including connections etc. as required.

Supplying and Fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-

Double door-12 way

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amps. Cat-A.

Supplying and Fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450 mm & cross-sectional area (25.4 mm x 4.75 mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530 mm x 450 mm x 150 mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and Fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.

100 Amp. Category-A

200 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required.

Single pole & neutral. Cat-B.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required.

Supplying and errection of 40/50/63 Amp rating, 10 KA breaking capacity 240 Volts, C-curves minituature circuit breaker of following poles in the existing MCB DB complete with connections as required.

Double pole Cat-B.

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps. Cat-B.

Supplying and Fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Supplying and Fixing of lightening conductor finial, made of 25 mm dia 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate incuding holes etc completeas required.

Supplying and fixing of copper tape 20mmx3mm thick on parapet or surface of wall for lightening conductor as required (for vertical run).

Supplying and fixing of copper tape 20mmx3mm thick on parapet or surface of wall for lightening conductor as required (for horizontall run).

Providing and Fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XPLE power cable, working voltage 1100 volts grade direct in ground to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the armoured cable 4 Sq.mm (twin core) for yard light.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and Fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required of make Recold/Bajaj/Jaquar.

25 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and Fixing phenolic laminated sheet cover on the fan box and earthing etc. as required of make USHA/Crompton.

Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required.

Exhaust Fan, Light duty, (Domestic) 225 mm sweep

Providing and fixing 2x36 watt-LED (Category-A) of surface mounting decorative mirror optics luminaire with powder coated CRCA sheet steel housing, low glare aluminium mirror reflector, prewired with 110 V starter & 36/40 w copper ballast for housing CLED (but excluding the cost of CFLED), complete with all accessories, connections, testing and commissioning etc. as required.

Supplying and fixing of fancy wall bracket containg thread type LED lamp holder (s) of sizes and shapes complete with all accessories but excluding CFL lamp including making connections, testing etc. as required fixed type wall bracket 150mm dia, single lamp (Category-A). complete in all respect in all leads and lifts.

Providing, installation, testing and commissioning of tube fitting 1x20W LED complete in all respect in all leads and lifts.

Supplying and Fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:-

Providing and fixing 11 watt LED bulbs complete in all respect in all leads and lifts.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and Fixing bakelite batten/angle holder including connections etc. as required.

Providing and fixing of integral LED boundary wall lights fixed over GI pipe polls 1.2 mtrs height 50 mm dia, 9 watt LED lamp with 200 mm dia globe made of acrylic sheet complete in all respect in all leads and lifts.

Supplying and fixing stepped type modular fan regulator on the existing modulat box including making connections etc. as required complete in all respect in all leads and lifts.

Supplying and fixing 10 unit intercome exchange with phone sets and wiring complete in all respect in all leads and lifts.

Supplying and fixing of three star hot & cold split type inverter air conditioner 1.5 Tonne capacity Blue Star/LG/Voltas/Whirlpool/Lloyd/Smasung make having three star features auto clean filter four way swing all copper pipes including making provision of draining of back moisture water through GI pipe 20mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete in all respect in all leads and lifts.

Unipro Techno Infrastructure Pvt Ltd

SS RANA CONSTRUCTION PRIVATE LIMITED