Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹195.1 CrAccepted-AOC | ₹195.1 Cr | L1 | Accepted-AOC AOC |
| 2 | L2₹204.9 CrRejected-Finance | ₹204.9 Cr | L2 | Rejected-Finance Highest Rate Quoted by bidder |
| Sl No | Description | Qty | Unit | M/s Sivanssh Infrastructure Development Pvt. Ltd. L1 | KASANA BUILDERS PRIVATE LIMITED L2 |
|---|---|---|---|---|---|
| 1.00 | Civil work
DSR Item- 2.6.1
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil. | 26,037.22 | Cum | 150.04 ₹39.1 L | 157.39 ₹41.0 L |
| 2.00 | DSR Item- 2.26.1
Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil | 655.4 | Cum | 107.15 ₹70,226.11 | 112.8 ₹73,929.12 |
| 3.00 | DSR Item- 2.25
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | 17,259.44 | Cum | 165.4 ₹28.5 L | 173.62 ₹30.0 L |
| 4.00 | DSR Item- 2.25(a)
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete. | 2,246.06 | Cum | 591.57 ₹13.3 L | 622.75 ₹14.0 L |
| 5.00 | DSR Item- 2.27
Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. | 1,030.03 | Cum | 1,793.62 ₹18.5 L | 1,885.37 ₹19.4 L |
| 6.00 | DSR Item- 16.3.2
S/F RBM under floor i/c ramming and dressing complete. 63mm to 45 mm nominal size. | 367.61 | Cum | 1,295.95 ₹4.8 L | 1,363.81 ₹5.0 L |
| 7.00 | DSR Item- 2.35.3.1
Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment) | 12,190.07 | Sqm | 262.16 ₹32.0 L | 208.31 ₹25.4 L |
| 8.00 | DSR Item- 2.34.1
Supplying chemical emulsion in sealed containers including delivery as specified Chlorpyriphos/ Lindane emulsifiable concentrate of 20% | 32.97 | Lit. | 198.09 ₹6,531.03 | 208.31 ₹6,867.98 |
| 9.00 | DSR Item- 4.1.6
P/L cement concrete - all works upto plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 40 mm nominal size) | 66.55 | Cum | 6,058.69 ₹4.0 L | 6,364.3 ₹4.2 L |
| 10.00 | DSR Item- 4.1.8
P/L cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (zoneIII) : 8 graded stone aggregate 40 mm nominal size) | 2,444.02 | Cum | 5,745.08 ₹1.4 Cr | 6,056.11 ₹1.5 Cr |
Tender Value
₹195.8 Cr
EMD Value
₹2.2 Cr
Closing Date
13 May 2025, 5:00 pmClosed
General Manager
Office of Chief General Manager, Construction Wing, Uttarakhand Peyjal Nigam, Kamla Nagar(Opp. ONGC Hospital), Dehradun
CONSTRUCTION OF GIRLS SPORTS COLLEGE AT CHAMNIYA, LOHAGHAT, DISTT- CHAMPAWAT
2025_MDPEY_83173_1
1555/Nivida(Garh)KhelDDUN/52 Dt 25/04/2025
Open Tender
Civil Works
730 days
CHAMNIYA, LOHAGHAT, DISTT- CHAMPAWAT
Please refer tender document
3 documents required · 3 mandatory
₹11,800
PM, Temp.Const.Unit(Khel), UKPJN, Dehradun
₹2.2 Cr
Dehradun
27 Aug 2025
26 Apr 2025
15 May 2025
26 Apr 2025
13 May 2025
3 May 2025
2 May 2025
Amount
Civil work DSR Item- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.
DSR Item- 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil
DSR Item- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
DSR Item- 2.25(a) Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete.
DSR Item- 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.
DSR Item- 16.3.2 S/F RBM under floor i/c ramming and dressing complete. 63mm to 45 mm nominal size.
DSR Item- 2.35.3.1 Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment)
DSR Item- 2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
DSR Item- 4.1.6 P/L cement concrete - all works upto plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 40 mm nominal size)
DSR Item- 4.1.8 P/L cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (zoneIII) : 8 graded stone aggregate 40 mm nominal size)
DSR Item- 4.11 Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
DSR Item- 4.13 Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
DSR Item- 4.1.3 P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
DSR Item- 5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
DSR Item- 5.33.1.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level
DSR Item- 5.33.2.1 P/L RCC M25 design mix for columns, pillars piers etc.
DSR Item- 5.33.1.2 Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level. (Note : Cement content considered in M-30 is @ 350 kg/ cum)
DSR Item- 5.33.2.2 Providing M-30 grade concrete BMC/ RMC. (Note : Cement content considered in M-30 is @ 350 kg/ cum) for columns, pillars piers etc.
DSR Item- 5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein.
DSR Item- 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :
DSR Item- 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete
DSR Item- 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
DSR Item- 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts
DSR Item- 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.
DSR Item- 5.9.3 Suspended floors, roofs, landings, balconies and access platform
DSR Item- 5.9.7 Stairs, (excluding landings) except spiral-staircases
DSR Item- 5.9.19 Weather shade, Chajjas, corbels etc., including edges
DSR Item- 5.9.20 Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick
DSR Item- 5.11.1 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
DSR Item- 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars
DSR Item- 5.45 Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063). Wall Joint of 100 mm gap
DSR Item- 5.46.1 Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates an universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall conform to ASTM 6063).Roof Joint of 100 mm gap
DSR Item- 5.26 Providing and filling in position, blown bitumen in expansion joints
DSR Item- 5.29.2.2 Providing and fixing sheet covering over expansion joints with iron screws: Aluminium fluted strips 3.15 mm thick. 200 mm wide
DSR Item- 11.3.1 P/L 40 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement.
DSR Item- 6.1.1 Brick work with bricks of Ist class in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)
DSR Item- 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
DSR Item- 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
DSR Item- 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
DSR Item- 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
DSR Item- 9.21.1 P/F ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
DSR Item- 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
DSR Item- 9.62 Providing and fixing ISI marked M.S.Oxidised fitting for door windows.
DSR Item- 9.62.2 250x16 mm sliding door bolts
DSR Item- 9.63.1 250x10 mm Tower bolt
DSR Item- 9.63.3 150x10 mm Tower bolt
DSR Item- 9.66.1 125 mm handles
DSR Item- 9.66.2 100 mm handles
DSR Item-9.68.3 200 Casement stays (straight peg type) with necessary screws etc. complete, weighing not less than 120 gms
DSR Item- 9.75 Providing and fixing ISI marked bright finished brass fitting for door windows.
DSR Item- 9.75.2 250x16 mm sliding door bolts
DSR Item-9.74.1 250x10 mm Tower bolt
DSR Item- 9.74.3 150x10 mm Tower bolt
DSR Item- 9.81.1 125 mm handles
DSR Item- 9.81.2 100 mm handles
DSR Item- 9.101.2 hanging floor door stopper, Twin rubber stopper
DSR Item- 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
DSR Item- 10.14.2.1 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: (A) "Profile C" Fixing with adjustable lugs with split end tail to each jamb (S.R.)
DSR Item- 10.15.1 Providing and fixing M.S. Tubular frames for Windows, Ventilators with rectangular/ L-Type sections, made of 2.0 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer: Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
DSR Item- 25.8 Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi- etallic contacts, all complete to perform as per Specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
DSR Item- 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
DSR Item- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.
DSR Item- 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm
DSR Item- 11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.
DSR Item- 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
DSR Item- 11.55 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
DSR Item- 11.56.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
DSR Item- 11.23.5 Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble
DSR Item- 11.26.1 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
DSR Item- 11.25 Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.
DSR Item- 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
DSR Item-16.68 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
DSR Item- 14.90.1 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete.The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm Thick
DSR Item- 14.91.1 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete.The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm Thick
DSR Item- 12.54.2 Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesand having NRC of 0.5, electro statically polyester powdercoated of thickness 60 microns (minimum), including factory painted after bending and perforation.
DSR Item- 12.52.2 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.
DSR Item- 12.52.3 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.
DSR Item- 12.1.1 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 12.4.2 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 12.7.2 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.63 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
DSR Item- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
DSR Item- 13.3.1 20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
DSR Item- 13.16.1 6 mm cement plaster 1:3 (1 cement: 3 fine sand)
DSR Item- 13.50.2 Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
DSR Item- 13.50.3 Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
DSR Item- 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.9 kg/10 sqm)
DSR Item- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
DSR Item- 13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give an even shade.
DSR Item- 13.41.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer
DSR Item- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
DSR Item- 13.8 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
DSR Item-16.53 P/F concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre
DSR Item- 26.24 Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete.With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles
DSR Item- 12.57 Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge.
DSR Item- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
DSR Item- 6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
DSR Item- 4.1.10 P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
DSR Item- 9.96 Providing and fixing aluminium door window fittings, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), complete :
DSR Item- 9.96.2 A) 250x16 mm sliding door bolts
DSR Item- 9.97.2 B) 250x10 mm Tower bolt
DSR Item- 9.97.4 C) 150x10 mm Tower bolt
DSR Item- 9.100.1 D) 125 mm handles
DSR Item- 9.100.2 E) 100 mm handles
DSR Item- 10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
DSR Item- 10.14.1.1 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: (A) "Profile B" Fixing with adjustable lugs with split end tail to each jamb (S.R.)
DSR Item- 13.7.2 12mm C.P. finished with a floating coat of neat cement in cement mortar 1:4( 1 cement : 4 fine sand)
DSR Item- 16.70.1 G.I. chain link fabric fencing with G.I. wire of dia 4 mm
DSR Item- 19.19.1.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions
DSR Item- 19.19.4.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia
DSR Item- 19.15.1 Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar
DSR Item- 23.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia
DSR Item- 23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge
DSR Item- 23.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge
DSR Item- 23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.
DSR Item- 23.8 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.
DSR Item- 23.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia
DSR Item- 23.4.2 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia
DSR Item- 23.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia.
DSR Item- 23.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp
DSR Item- 23.15.2 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia.
DSR Item- 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
DSR Item- 19.3.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm dia. R.C.C. pipe
DSR Item- 19.4.1.2 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With Sewer bricks conforming to IS : 4885
DSR Item- 19.7.1.2 Constructing brick masonry M.H. in C.M. 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with C.M. 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90X80X45 cm i/c C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With Sewer bricks conforming to IS : 4885
DSR Item- 19.8.1.2 Extra for depth for manholes : Size 90x80 cm- With Sewer bricks conforming to IS : 4885
DSR Item- 6.20.3 Design, supply / construction, installation /erection, commissioning, testing and operation & maintenance of 170 KLD capacity Sewerage Treatment Plant with all civil, electrical, mechanical, instrumental and inter connecting piping works complete in all respect on turnkey basis based on open proven technology having zero/ lowest power consumption with all ancillary works. The STP should have suitable foundation Considering Seismic forces, including excavation, filling, dewatering (if required) disposal of surplus earth, supply of all materials, labour, T&P etc. as required for proper completion of work. The work will include submission of detailed design & drawings and Vetting before starting of the work, as per direction of client /employer.
DSR Item- 4.5 Design and construction of 100 KL (2 Part) capacity, RCC Under Ground Tank with suitable foundation Considering Seismic forces, including supply of all materials, labour, T&P etc. as required for proper completion of work. The earthquake resistant design must be in conformity with IS:456, IS:1893, IS:13932 & IS:13920 (latest versions). RCC work for water retaining portion should be not less than M-25 (design mix). The work will include submission of detailed design & drawings and Vetting before starting of the work, as per direction of client /employer.
DSR Item- 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)
DSR Item- 21.1.1.2 For fixed portition: Powder coated aluminium (minimum thickness of powder coating 50 micron)
DSR Item- 21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron)
DSR Item- 21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness
DSR Item- 21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
DSR Item- 10.29.2 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete: Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides
DSR Item- 21.8.1 Filling the gap in between uPVC, aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete: Upto 5mm depth and 5 mm width
DSR Item- 11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
DSR Item- 12.1.2 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.8 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 12.4.1 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 12.7.1 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²
DSR Item- 12.61 Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m3, 50 mm thick, wrapped in 200 G virgin Polythene bags placed over existing false ceilng and held in position by criss-crossing Gl wire.
DSR Item- 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
DSR Item- 10.11.1 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
DSR Item- 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
DSR Item- 9.51.2 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading
DSR Item- 9.7.8 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading
DSR Item- 9.147.B3.2 Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required),EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)
DSR Item- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube
DSR Item- 10.25.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
DSR Item- 10.30.2 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes
DSR Item- 10.5.1 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces
DSR Item- 10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover
DSR Item- 10.7 Providing and fixing ball bearing for rolling shutters.
DSR Item- 10.8.1 Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area
DSR Item- 11.55.1 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
DSR Item- 22.7.1 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
DSR Item- 22.6 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.
DSR Item- 12.21 Providing gola 75x75 mm in cement concrete (1:2:4).
DSR Item- 22.1.1 Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of :(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course. Joints sealed and grouted with cement slurry mixed with water proofing compound.(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.
DSR Item- 22.2.1 Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough kota stone.
DSR Item- 22.14.1 Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)
DSR Item- 22.14.2 Grading roof for water proofing treatment with Cement mortar 1:3 (1 cement : 3 coarse sand)
DSR Item- 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
DSR Item- 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
DSR Item- 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
DSR Item- 17.32.4 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm
DSR Item- 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter
DSR Item- 17.73.2 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms
NSI Item- P/F Upvc nahani trap 110x110mm dia
DSR Item- 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
DSR Item- 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
NSI Item- P/F Upvc terminal guard 110 mm dia
DSR Item- 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
DSR Item- 12.42.5.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend
NSI Item- P/F Upvc door bend 110 mm dia.
DSR Item- 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia
DSR Item- 12.42.4.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110x110x110 mm tee
DSR Item- 17.8 P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
DSR Item- 17.5.2 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern
DSR Item- 8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade
DSR Item- 17.11.2 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm
DSR Item- 17.10.1.2 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 225 mm
DSR Item- 12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm Shoe
DSR Item- 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4).
DSR Item- 18.11.1 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore
DSR Item- 18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
DSR Item- 18.10.2 20 mm dia nominal bore
DSR Item- 18.10.3 25 mm dia nominal bore
DSR Item- 18.12.4 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore
DSR Item- 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
DSR Item- 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes.
DSR Item- 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass hreaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
DSR Item- 18.7.2 20 mm nominal outer dia Pipes
DSR Item- 18.7.3 25 mm nominal outer dia Pipes
DSR Item- 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
DSR Item- 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
DSR Item- 18.17.1.A 20mm nominal bore
DSR Item- 18.17.1 25 mm nominal bore
DSR Item- 18.17.2 32 mm nominal bore
DSR Item- 18.17.4 50 mm dia
DSR Item- 18.17.6 80 mm dia
DSR Item- 18.20.2 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 20 mm nominal bore
DSR Item- 18.31.1 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :
DSR Item- 18.31.1.1 100 mm dia Class I
DSR Item- 18.31.3.1 150 mm dia Class I
DSR Item- 18.32.1 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
DSR Item- 18.33.1 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation oncrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
DSR Item- 18.34.1 Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
DSR Item- 18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :
DSR Item- 18.40.2 20 mm diameter pipe
DSR Item- 18.40.3 25 mm diameter pipe
DSR Item- 18.40.4 32 mm diameter pipe
DSR Item- 18.40.6 50 mm diameter pipe
DSR Item- 18.40.8 80 mm diameter pipe
DSR Item- 18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :
DSR Item- 18.41.2 20 mm diameter pipe
DSR Item- 18.41.3 25 mm diameter pipe
DSR Item- 18.41.4 32 mm diameter pipe
DSR Item- 18.41.6 50 mm diameter pipe
DSR Item- 18.41.8 80 mm diameter pipe
DSR Item- 18.41.9 100 mm diameter pipe
DSR Item- 18.41.10 150 mm diameter pipe
DSR Item- 18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :
DSR Item- 18.46.2 20 mm diameter pipe
DSR Item- 18.46.3 25 mm diameter pipe
DSR Item- 18.46.4 32 mm diameter pipe
DSR Item- 18.46.6 50 mm diameter pipe
DSR Item- 18.46.8 80 mm diameter pipe
DSR Item- 4.2 Design and construction of 400 KL capacity, 20 m staging RCC intz type Over Head Tank with suitable foundation Considering Seismic forces, including supply of all materials, labour, T&P etc. as required for proper completion of work. The earthquake resistant design must be in conformity with IS:456, IS:1893, IS:13932 & IS:13920 (latest versions). RCC work for water retaining portion should be not less than M-25 (design mix). The work will include submission of detailed design & drawings and Vetting before starting of the work, as per direction of client /employer. One meter wide balcony around the tank at the middle ring beam (Junction of conical wall and containers vertical wall).One meter wide RCC two columns stair case as an access to the top dome of the tank from ground level. 60cm, wide M.S. ladder from top dome to the inside of the tank upto bottom dome of 65x65x6 mm angle iron and 20mm dia plain M.S. bars @ 25cm. C/C welded or riveted with suitable hand rail etc. 1200mm dia ventilator of 50x50x6mm angle iron fitted at the crown of top dome with mosquito proof wire mesh over expanded metal jali.600x600mm M.S. manhole cover of 5mm thick M.S. plate duly hinged with 50x50x5mm angle iron frame embedded in the top dome at appropriate place with locking arrangement shall be provided with overlap.Three rows of G.I. (medium) 20mm dia pipe railing with 50x50x6mm angle iron post of clear height 1.00 m at a distance of 1.50m center to center around the balcony, top dome and along the stair case from ground level to top dome.Three rows of G.I. (medium) 20mm dia pipe railing with 50x50x6mm angle iron post of clear height 1.00 m at a distance of 1.50m center to center around the balcony, top dome and along the stair case from ground level to top dome.Water level indicator as per direction of engineer I/C (confirming to latest IS code.)Lightening conductor arrangements including earthing as per latest I.S. code.Fixing of inlet, outlet, washing and over flow pipes and their sluice valves, duck foot bends etc. from 150mm to 300mm dia including all materials, necessarily required for jointing and erecting. The limits of pipe fixing shall be from dome of the tank to one meter outside the apron of the tank. Overflow pipe shall be vertical type at required position or otherwise specified. Also, construction of inlet, outlet & washout/over flow chambers and their RCC covers as per departmental type design.Clamping the vertical pipe with M.S. clamps of size 50x6mm at 1.50M C/C.Filling the tank as many times as required with water and testing for water tightness and making it water tight, water for testing the tank shall be arranged by the contractor.
Painting the outlet inlet, washout and over flow pipe with one coat of oxide primer and two coats of paint of approved quality (Asian, Berger, Nerolac etc.) and shade.Painting the entire tank with three coats of (including base coat) exterior weather coat Apex or equivalent of Asian, Berger, Nerolac etc. of approved quality and shade as per direction of the Engineer-In-charge.Painting the balcony and staircase railing and M.S. Manhole cover, ventilator angle iron posts with one coat of oxide primer and two coats of paint of approved quality (Asian, Berger, Nerolac etc.) and shade.Filling of earth, ramming and watering the earth upto the plinth level which will be about 0.30m above from natural ground level for constructing floor & apron projecting one meter form the tank columns and drain outside. The apron shall be 25mm PCC 1:2:4 over 80mm thick PCC 1:6:12 at floor of the tank with suitable glass strips with brick masonary walls in 1:6 cement sand mortar required to raise ground level to plinth level including all materials etc.
DSR Item- 2.13.1.2 Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material rmeasurements and disposal of nserviceable material as directed, within a lead of 50 m :Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia
DSR Item- 18.58.1.1 Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia
DSR Item- 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
DSR Item- 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore
DSR Item- 18.20.3 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore
DSR Item- 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
DSR Item- 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore
DSR Item- 18.64 Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms
DSR Item- 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
DSR Item- 18.12.2 20 mm dia
DSR Item- 18.12.3 25 mm dia
DSR Item- 18.12.6 50 mm dia
DSR Item- 18.12.8 80 mm dia
DSR Item- 18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :
DSR Item- 18.72.1 100 mm dia Ductile Iron Class K-7 pipes
DSR Item- 18.72.2 150 mm dia Ductile Iron Class K-7 pipes
DSR Item- 7.12.1.2 Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : One face dressed : White sand stone
DSR Item- 24.2 Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.
DSR Item- 24.8 Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).
DSR Item- 26.37 Cleaning of exposed concrete, Brick, Stone surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
NSI Item- Supply & Installation of Roof shingles sheet, Hip & ridge over RCC slopi roof plastered surface, all complete as per direction of the Engineer in
DSR Item- 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length. Sal wood
NSI Item- Installation / carving work on solid sal wood for traditional uttarakhand hilly area design
NSI Item- Acoustical Ceiling : Providing & fixing perforated Gypsum false ceiling , as marked in the drawings, consisting of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 300mm c/c. Finished in 12.5mm thick micro-perforated gypsum board, 1200mm x 2400mm, with 3mm dia square perforations. The board shall have an overlay of 50mm thick, 1000 GSM polyester wadding, appropriately covered with FGT tissue (in the case of glasswool/ rockwool). The ceiling to be finished with 2 or more coats of mat type plastic emulsion paint after proper jointing & making surface smooth. Approved make of gypsum perforated board: Knauf Danoline/ Absound Overseas micro perforated/ Saint gobin -Quattro board.
NSI Item- Acoustical paneling on walls : Providing and fixing Acoustical Wall paneling with Compressed polyester fibre nonwoven 10mm thick panels with a density of 200kg/m3, of size1200mmX600mm with an NRC of 0.80 to 0.85 . The panels to be pasted with approved construction adhesives over 9mm thick perforated ply (minimum 20% perforations). The 9mm thick perforated ply shall be fixed over GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1000GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. Approved Make : Acoustic India/ Absound Overseas/AMF.
NSI Item- Providing & fixing 100x15mm thick Polished teak wood skirting at the bottom of wall paneling. The skirting shall be fixed over 12mm thick commercial ply to match the level of paneling.
NSI Item- Providing and fixing 90x20mm thick, in random length, Maple wood planks flooring with tongue & groove joints ,fixed to pine wood joist of size 72 x 48 mm at 230-300 mm c/c in one direction , pine wood joists to be resiliently supported on 75x50 mm rubber pads. The cavity of framing shall be filled with 50mm thick rock wool insulation of density 48kg/cum. Polishing of flooring on exposed surface: In horizontal/vertical plane (Rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes.
NSI Item- Entry/exit doors 77mm thick, acoustic doors consisting of fire resistant materials & peripheral seals all around . The door to be laminated with 1mm thick laminate. The Door shutter frames to be of klin dried chemically treated second class teak wood. The door shutter frame to be lapped with 12mm thick BWR ply duly treated for fire retardance. Make : Global Fire/ Navair/ Absound Overseas.
NSI Item- Chowkhats for the doors in second class teak wood of size 125x 75mm duly fire treated.
NSI Item- Providing and fixing panic bars for the doors with double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
NSI Item- Providing and fixing Hinges (Steel with bal bearings ) of size 125 X 32mm fixed with steel drive all screws of 35mm. Make: Doors, Ozone, Dorma
NSI Item- Providing and fixing external trim with locking arrangement & handle for panic bars double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
NSI Item- Providing and fixing heavy duty door closers of load capacity of 100-120kg with all necessary parts. Make: Doors/Dorma/Godrej
NSI Item- Micro-perforated (3x3sqmm perforations) Gypsum board false ceiling for absorption: Providing & fixing perforated Gypsum false ceiling , as marked in the drawings, consisting of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 300mm c/c. Finished in 12.5mm thick micro-perforated gypsum board, 1200mm x 2400mm, with 3mm dia square perforations. The board shall have an overlay of 50mm thick, 1000 GSM polyester wadding, appropriately covered with FGT tissue (in the case of glasswool/ rockwool). The ceiling to be finished with 2 or more coats of mat type plastic emulsion paint after proper jointing & making surface smooth. Approved make of gypsum perforated board: Knauf Danoline/ Absound Overseas micro perforated/ Saint gobin -Quattro board.
NSI Item- Stage suspension Grid: Providing & fixing MS suspension grid system over stage for hanging stage services made of 2 nos 40x40x5mm MS angles welded back to back with 50x12x12mm thk studs as MS spacers sandwiched between the MS angles so as to maintain 12mm gap between MS angles, the welded angles to be placed @ 1200mm c/c in one direction and 40x5mm thick MS Tee @ 600mm c/c in other direction. The MS grid to be suspended from the roof structure by means of MS flat suspender of 50x6mm thick MS flats @ 1200mm c/c in both directions. All MS members to be painted with a coat of red oxide primer & 2 or more coats of black enamel paint.
NSI Item- Fibril acoustical tiles in stage ceiling: Providing and fixing Fibril black acoustical tiles of size 1200x600x25 mm, to be installed over existing MS suspension grid. Which will comprise of NRC 0.80. Approved make: Absound Overseas/Herra Design/Acoustic India.
NSI Item- HDF based sound slats paneling for rear wall, side walls, proscenium & stage front (for LF absorption): Providing and fixing Wood melamine finish HDF based sound slat panels with lineal perforations on walls.The panels shall be with melamine laminate finish of size 2430mm x 128mm x17mm with 4mm slats at 28 mm pitch, Toungue and Groove edges for seamless mounting having density of 750 to 800kg/m3 . The back of the panels are perforated with 10mm diameter circular holes with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method.Panel is to be fixed on GI framework as recommended by the manufacturer with screw fixed horizontal / vertical to wall at every 600mm c/c in tongue & groove system on GI studs 48x36x34mm framework. The cavity of framework should be inserted with 50mm thick, 1000 GSM polyester wadding appropriately covered with FGT tissue (in the case of glasswool/ rockwool).. Approved makes: Anutone/Absound Overseas/Acoustic India Inc
NSI Item- Acoustical paneling on rear & side walls (for HF absorption): Providing and fixing Acoustical Wall paneling with Compressed polyester fibre nonwoven 10mm thick panels with a density of 200kg/m3, of size1200mmX600mm with an NRC of 0.80 to 0.85 . The panels to be pasted with approved construction adhesives over 9mm thick perforated ply (minimum 20% perforations). The 9mm thick perforated ply shall be fixed over GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1000GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. Approved Make : Acoustic India/ Absound Overseas/AMF.
NSI Item- Stage Walls treatment : Providing and fixing 20mm thick black fibril wood wool panels having density of 400kg/cum, fixed over a framework of GI channels consisting of 48x36x34mm GI Stud wall channels & floor channels @ 600mm c/c, filled with 50 mm thick 500GSM thermally bonded polyester wadding to be held in position with 19mm GI wire netting. Approved Make : Herra Design/ Acoustic India/ Absound Overseas.
NSI Item- Providing & fixing 100x15mm thick Polished teak wood skirting at the bottom of wall paneling. The skirting shall be fixed over 12mm thick commercial ply to match the level of paneling.
NSI Item- Providing and fixing 90x20mm thick, in random length, Maple wood planks flooring with tongue & groove joints ,fixed to pine wood joist of size 72 x 48 mm at 230-300 mm c/c in one direction , pine wood joists to be resiliently supported on 75x50 mm rubber pads. The cavity of framing shall be filled with 50mm thick rock wool insulation of density 48kg/cum. Polishing of flooring on exposed surface: In horizontal/vertical plane (Rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes.
NSI Item- Providing and fixing second class teak wood lipping/moulded beading or taj beading of size 50x50mm fixed with wooden adhesive of approved quality and screws/nail on external edges of stage .The work shall be executed as per drawings ,specifications & instructions of engineer in charge.
NSI Item- Entry/exit doors for the auditorium 77mm thick, acoustic doors consisting of fire resistant materials & peripheral seals all around . The door to be laminated with 1mm thick laminate. The Door shutter frames to be of klin dried chemically treated second class teak wood. The door shutter frame to be lapped with 12mm thick BWR ply duly treated for fire retardance. Make : Global Fire/ Navair/ Absound Overseas.
NSI Item- Chowkhats for the doors in second class teak wood of size 125x 75mm duly fire treated.
NSI Item- Providing and fixing panic bars for the doors with double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
NSI Item- Providing and fixing Hinges (Steel with bal bearings ) of size 125 X 32mm fixed with steel drive all screws of 35mm. Make: Doors, Ozone, Dorma
NSI Item- Providing and fixing external trim with locking arrangement & handle for panic bars double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
NSI Item- Providing and fixing heavy duty door closers of load capacity of 100-120kg with all necessary parts. Make: Doors/Dorma/Godrej
NSI Item- Providing and fixing of push back type 525-550mm c/c Fire Retardant fabric (FR Fabric conforming to BS EN 1021&1) upholstered chair. The chair to have MS tubular framework welded together with continous arc welding. The chair shall have powder coating of 65microns on all of the MS tubular framework . The seat shall have Polyurethane foam of density 50+3 Kg/cum & Back to have density of 50+3 Kg/cum. The height of the back to be 950-1000mm from the ground to top of back & for Seat to be 400-450mm from the ground . The rear of back shell & bottom of seat shell to be Polypropylene plastic in black colour Polypropylene plastic cover. The wooden armrest to be of 80mm & 400mm length with melamie polished in black colour . The armrest between two chairs in a row to be shared & at the both ends to be individual. Including cost of expnasion fastners as required of reputed make. The bench shall be fabricated as per drawings ,specifications & instructions of engineer in charge. Approved Make: Krishna Quenette / Featherlite / Absound Overseas/Wipro.
NSI Item- Providing and fixing machine tuffed loop pile high low scroll nylon carpet effective pile height 6mm, total pile weight not less than 850 gm/sqm. secondary backing action back 55 gms/sqm. In rolls of 3.66 mtr. width as per size, shade, design and direction of Engineer-in-charge and as per manufacturer's specifications. The sample may be approved by the Engineer-in-charge before start of the work. The surface area will be measured for payment. The carpet to be bakced with 6mm thick PU underlay. Approved make: Absound Overseas, Birla Transasia, CCIL.
NSI Item- High quality 54x3W LED PAR Light used as a Effect Light, Spot Light and Strobe Light etc. with below specifications: • Lamp: 54 X 3W RGBW LED (12R+18G+18B+6W) • Max. Power consumpsion: 160W • Power supply: 100-230V AC, 50/60Hz • Power cable: 3 core 1.5 sq. mm. copper PVC insulated • Channels: 8 Channel DMX-512 • Beam angle: 25° • LUX @ 2m: 11,000 • Control mode: DMX,Manual and Master Slave • Dimming: 0 - 100% • Function: strobe, dimming, sound active and Master slave. • Housing: Diecast aluminium with black epoxy polyster powder coated • Power and DMX: Loop in and loop out • Dimension: W 220 x L 240 x H 335mm • Weight: 2.9 Kg • Certification: CE Make: Leksa, New Age
150W CE Certified LED Moving Head light with technical specifications as below: • Voltage : AC100V-240V, 50/60Hz • Lamp :150W LED • Channel :12 /16 channels • Pan scanning : 540° • Tilt scanning : 270° • Color Wheel 1 : color wheel (10 colors + open, rotating in directions and rainbow effect) • Color Wheel 2 :Rainbow color wheel including 6 colors • Gobo Wheel : 13 gobos (lncluding 4 glass gobos) + open • Prism: 8-facet prism with clockwise andanti-clockwise rotation • Dimmer: 0%-100% linear dimmer • Foggy: 0%-100% linear foggy • Touch screen with 180° reversed available and four press buttons • Dimentions : H: 425 x W 310 x D 295 mm • Gross Weight : 20KG • Certification: CE Make: Leksa, New Age
NSI Item- High quality 200W LED Profile Spot Light used as a Spot Light and high-contrast gobo projection Light. Other Technical specifications as below: • Lamp Power : 200W COB LED • Power Supply : AC 110-230V, 50Hz. • CRI : >90 • Colour Temperature : 3200K • Focus : Manual Focus • Beam Angle : 19° • Control : DMX, Autorun and Master/Slave • Shutter arrangements : Beam shapping shutter or plastic gobo projection assembly. • Lux Level - 20,375 lux @ 2 Mtr with beam angle 19°,3200K • Dimming : 0 - 100% dimming • Protection Rating : IP20 • Body Color : Black • Weight : 7.50Kg • Dimentions : W 300 x L 700 x H 310 mm. Make: Leksa, New Age
NSI Item- High quality LED 2x2 blinder matrix Light is used in Entertainment applications, Night club, Fashion shows, Film, Band performances, Discotheque, Stage performance , TV studio and large-scale show etc fixture with advanced COB LED technology with below specifications:- • Power Consumption: 400W • Power Supply: 100-240 AC, 50-60Hz • Light Color: Single color warm white (3200K) • LEDs Qty : 4 pieces • Channel: 4/8 channel • Lifetime: Over 50,000 hours • Beam Angle: 30 degree • Control mode: DMX512,Master/Slave, Auto Run, Sound active. • Dimmer: 0~100% linearly adjustable • LUX: 8270 LUX @ 2m • IP Grade: IP20 • Dimension: 117 x 350 x 382 mm • Net Weight: 7 kgs • Certification: CE Make: Leksa, New Age
NSI Item- High Quality 20x15W RGBWA 5 in 1 LED Wash Light fixture with below specification details. • Light Source : 20 x 15W RGBWA 5 in 1 LEDs • Operating Voltage : 100-240VAC, 50-60 Hz • Power: 300W Max • IP Rated IP20 /IP 65 • Beam angle : 45°/30° • DMX Channels : 5/9 • Operating Modes : DMX512 / Manual / Color Preset • Dimmer : 0-100% linear adjustment • Operating Modes DMX, Master/Slave, Color Preset • Housing Cast aluminum housing with natural cooling system • Power cable & DMX cable In-out looping cables • Dimension: 360 x 210 x 350 mm • Net Weight: 7.4 kgs Make: Leksa, New Age
NSI Item- Supply and fixing of LED Exit Light with battery back up. Make: Prolite, Bajaj
NSI Item- MS Pipe Class B dual barrel 40NB powder coated with Matt black finish, 2.2 mm wall thickness Pipe should have under gone 7 tanks chemical treatment process and rusto cleaned.
NSI Item- Fixed FOH light bar, length 18 Mtrs made using 40NB dual barrel with perforated Cable tray undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish and provided with suitable suspender and clamps.
NSI Item- Providing and fixing fabric wings on stage made of FR treated black cotton fabric stitched with pleats, fixed to ceiling frame with pivoted arrangement. Make: Nexgen/RSWM/Banswara Syntax
NSI Item- Main Valance fixing arrangement using 40NB Pipe 2mm thick, 23 mtr in length MS pipe, coated with matt black texture finish with mounting brackets to suspend the arrangement.
NSI Item- SUPPLY INSTALLATION TESTING AND COMMISSIONING of FRONT CURTAIN made out of FR Treated approved colour velvet cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. App size 21000x9000. Make of fabric: Banswara, Reliance, Raymonds, Nexgen.
NSI Item- Providing & fixing of the Border frills out of Fire retardant Crape black colour ( weight not less than 290 gms/sqm Make: Nexgen/RSWM/Banswara Syntax)) fabric in 1:2 gathers & acessories like cotton dori eyelets of brass complete hung from the ceiling suspension grid complete.
NSI Item- P/f of the cyclorama for the stage by fixing 35x35x5mm MS angle on the wall with MS angle hold fasts secured to the walls & 40mm dia 14G MS pipe welded to it as per the drgs. Further 40mm dia pipe welded to it at 600 centres vertically at an angle of 45 deg. & finally welding 40 mm dia pipe horzontally to it. The pipe to be supported away at 200mm centers by MS pipe.(MS framework payable separately) Further welding to it 12mm dia MS hooks welded both (top ,bottom & sides). The cyclorama frame to be supported by MS angle hold fasts of 35x35x5mm on the wall at 1200mm centers. Finally fixing PVC perforated screen, cyclorama cloth as per approved sample & fixing by cotton dori 10mm thick complete.
NSI Item- Installation hardwares such as clamps, connectors, glands, lugs, ferruels, welding rods etc.
NSI Item- MS perforated trays of size 40 mm X 75 mm X 40 mm, duly powder coated with matt black texture finish paint along with clamping arrangement.
NSI Item- MS perforated trays of size 40 mm X 150mm X 40 mm, duly powder coated with matt black texture finish paint along with clamping arrangement.
NSI Item- Grid mount photo isolator DMX Amplifier unit 1 DMX input and 8 isolated output with following specifications: • Power Supply: 90-240V AC, 45-63Hz. • Control: DMX 512 protocol, • Control Signal input: 5 pin XLR female, • Size: 482 x 44 x 128mm , • Weight: 2Kg.with splitter bracket. Make: Leksa, New Age
NSI Item- Digital Lighting Console with 1024 DMX channels • 1024 Channels. • 96 Fixtures. • 96 Dimmer Control Channels. • Time control of scenes: Fade in/out, LTP slope • Channels for each fixture 40 primary + 40 fine tune • LCD display with back light • 60 Scenes/Playbacks • 600 Scene step • 10 Scenes to run simultaneoulsy • Shape generato: Shapes of Dimmer, Pan/Tilt, RGB, CMY, Color, Gobo, Iris and Focus • Master slider - Global, playback, fixture • USB Memory - FAT32 supported Make: Leksa, New Age
NSI Item- M.S. Pipe Ladders to be provided on sides of the Stage to be fixed on the existing GI pipe or top grid. Made of 50mm x 25mm MS pipe complete as required size 1200x600. CUSTOM BUILT
NSI Item- PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx2.5 sq mm. Make: Polycab.
NSI Item- DMX signal cable for DMX network. Make: Dlink / Canara / Polycab.
NSI Item- 16Amp sockets and swiches with MS boxes.
NSI Item- PVC conduits for wiring
NSI Item- Installation, testing and commissioning of Stage lighting & furnishing system including training to technical staff.
NSI Item- Supply Installation Testing and Commissioning of powered 15" Main Speakers (Left & Right) Frequency Range (-10dB): 50Hz-20kHz Power capacity: upto 1000W Maximum SPL: >120dB To include mounting accessories and connectors In case if OEM is giving Passive array speakers than supporting Class D amplfiiers to be added from Same OEM with indivudal speakers driven in Biamplified mode with minimum headroom 3dB. Make: EV/BOSE/ Music Group / Harman /Eqvt approved by Engineer in Charge
NSI Item- Subwoofer system: Supply Installation Testing and Commissioning of powered 18" subwoofer (Left and Right) Frequency Range(-10dB): 35Hz-200Hz Power: upto 1500W Maximum SPL: >110dB To include mounting frame, accessories and connectors In case if OEM is giving Passive array speakers than supporting Class D amplfiiers to be added from Same OEM with indivudal speakers driven in Biamplified mode with minimum headroom 3dB. Make: EV/BOSE/ Music Group / Harman /Eqvt approved by Engineer in Charge
NSI Item- FIILLERS: Supply Installation Testing and Commissioning of powered 12" Filler Speakers Frequency Range (-10dB): 50Hz-20kHz Power capacity: upto 1000W Maximum SPL: >120dB To include mounting accessories and connectors In case if OEM is giving Passive array speakers than supporting Class D amplfiiers to be added from Same OEM with indivudal speakers driven in Biamplified mode with minimum headroom 3dB. Make: EV/BOSE/ Music Group / Harman /Eqvt approved by Engineer in Charge
NSI Item- STAGE MONITORS: Supply Installation Testing and Commissioning of powered 8" Stage Monitors Frequency Range (-10dB): 50Hz-20kHz Power capacity: upto 1000W Maximum SPL: >100dB To include mounting accessories and connectors In case if OEM is giving Passive array speakers than supporting Class D amplfiiers to be added from Same OEM with indivudal speakers driven in Biamplified mode with minimum headroom of 3dB. Make: EV/BOSE/ Music Group / Harman /Eqvt approved by Engineer in Charge
NSI Item- GREEN ROOM, CONTROL ROOM and BALCONY SPEAKERS : Supply Installation Testing and Commissioning of powered two way 5"-6" Speaker pair Frequency Range (-10dB): 60Hz-20kHz Peak Power capacity>160W Maximum SPL: >110dB Mic/Line Input and Link output To include Wall mounting accessories and connectors Make: EV/BOSE/ Music Group / Harman Eqvt approved by Engineer in Charge
NSI Item- Supply of Control room headphones Wired around the ear headphones for monitoring Frequency Reposnse - 25Hz to 20KHz Make: AKG/Audiotechnica/Shure /Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- MICOPHONES: Supply Installation Testing and Commissioning of Wired vocal microphone Cardoid or hypercardoid pattern dynamic microphone Make: AKG/Audiotechnica/Shure / Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of Wired instrument microphone Cardoid or hypercardoid pattern dynamic microphone. Make: AKG/Audiotechnica/Shure/Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of Wireless Handheld microphone To include 1 handheld microphones, 1 receiver with power supply, 1 charger for handheld transmitter, Antenna, cables etc. No. of simultaneous Frequencies per band should be minimum 12 per band Make: AKG/Audiotechnica/Shure /Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of Lapel Microphone set To include 1 lapel microphones, 1 receiver with power supply, 1 body pack transmitter, 1 charger for body pack transmitter, Antenna, cables etc.No. of simultaneous Frequencies per band should be minimum 12 per band Make: AKG/Audiotechnica/Shure /Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of 18" gooseneck cardoid/ hypercardoid pattern dynamic microphone To include mounts, connectors and cables. Make: AKG/Audiotechnica/Shure /Beyerdynamic or Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of Active DI box To include mounts, connectors and cables Make: Klark technik/BSS or Eqvt approved by Engineer in Charge
NSI Item- Supply of microphone stand with boom - Floor standing Make: Custom/Eqvt approved by Engineer in Charge
NSI Item- Supply of microphone stand with boom - Table top Make: Custom/Eqvt approved by Engineer in Charge
NSI Item- CONTROL SYSTEM Supply Installation Testing and Commissioning of 24-Input 4/2-Bus Mixer with 10 Microphone Inputs, 4 stereo inputs,8 Compressors, EQs, Multi-FX Processor with LCD display, Wireless Option,built-in stereo USB/Audio Interface. Make: Music group, Harman, Yamaha
NSI Item- Supply Installation Testing and Commissioning of dual 31 band Graphic Equaliser Features: Auto gain control, delay control Make: Behringer/dbx/Eqvt approved by Engineer in Charge
NSI Item- Supply Installation Testing and Commissioning of Loudspeaker management system Inputs: 2, Outputs: 6 with RS232/RS485 control and Cascading feature Features: Auto gain control, delay control Make: EV/BOSE/QSC/ Music Group / Harman Eqvt approved by Engineer in Charge
NSI Item- Speaker cables 14AWG shielded twisted pair copper cable. Make: Belden/Sommer / Gotham /Eqvt approved by Engineer in Charge
NSI Item- Signal cables 20AWG shielded twisted pair copper cable Make: Belden/Sommer / Gotham /Eqvt approved by Engineer in Charge
NSI Item- Snake cables - 12 core 24AWG shielded twisted pair copper cable Make: Belden/Sommer / Gotham /Eqvt approved by Engineer in Charge
NSI Item- Microphone cables 24AWG shielded twisted pair copper cable Make: Belden/Sommer / Gotham /Eqvt approved by Engineer in Charge
NSI Item- Providing and fixing miscellaneous Connectors for audio/video system. Make: Neutrik/Amphenol/Switchcraft Eqvt approved by Engineer in Charge
NSI Item- Supplying and fixing 28U AV rack with power bar.
NSI Item- Supply installation testing & commissioning of lazer technology, minimum 7500 lumens projector with WUXGA resolution of 1920 x 1200 with contrast ratio of 2400:1 ; with standard lens only. Make: Digital Projection, Barco , NEC.
NSI Item- Supply Installation Testing and Commissioning of Motorised Projection Screen Remote operated Image Size:19'X12' Gain: >1 Make: Grandview/ Da-Lite/Draper Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of LED 42" Display for Green rooms With 2 HDMI inputs Accessories:Including Remote control, Wall mount or ceiling mount and other accessories etc Make: LG/Panasonic/Sony/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of DVD/Bluray player Region compatibility: compatible with indian region Media supported: With 7.1 facility BD-rom, DVD-R/RW, DVD+R/RW,CD, USB memory, External Hard drive (FAT32/NTFS) Video and Audio formats: WMV, WMA, WAV, AVI, MP3, MP4, MPEG, AAC and other common formats Output Terminals: HDMI, 3.5mm mini audio jack To include cables and connectors Make: Sony, Philips or eqvt
NSI Item- Supply Installation Testing and Commissioning of HDMI Video Matrix Switcher 2 in 6 out Make: Extron/Kramer/Wyrestrom / Aton/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of VGA to HDMI converter Make: Extron/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of HDMI to VGA converter Make: Extron/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of Shielded CAT6 cables Make: Extron/Kramer/ Amp / Belden Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of HDMI cables 20meters each Make: Extron/Kramer/Wyrestrom Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of HDMI cables 10meters each Make: Extron/Kramer/Wyrestrom Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of HDMI cables 5 meters each approved by Engineer in charge. Make: Extron/Kramer/Wyrestrom Eqvt
NSI Item- Supply Installation Testing and Commissioning of HDMI audio de-embedder Make: Extron/Kramer/Wyrestrom Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of Floor boxes - 1 HDMI + Audio Make: Custom/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of Floor boxes - Audio With 2 microphones Make: Custom/Eqvt approved by Engineer in charge
NSI Item- Supply Installation Testing and Commissioning of Floor boxes for Power With 3 power points. Make: Custom/Eqvt approved by Engineer in charge
NSI Item- Audio & Video system programming and commisioning charges.
DSR Item- 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
DSR Item- 16.2 Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
SOR Item- 4-2-3 Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402
SOR Item- 4-9 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. (By Mechanical Means with 1 km lead)
SOR Item- 3-4-2 Providing and laying Bituminous Concrete with the use of batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects for Grading-II (bituminous binder @ 5.4 % of mix)
SOR Item- 5-1-1 Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502
SOR Item- 5-3-2 Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504. (Bitumen VG-10 @ 3.3% of the weight of mix has been used for analysis purpose. The choice of bitumen will depend upon the prevailing site conditions and shall be in accordance with Clause 504 of MORD with Bitumen VG-30
SOR Item- 5-12-A-B-1 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Bitumen (VG-10)
SOR Item- 5-2-3 Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.
NSI Item- Providing and laying of World Athlctics (formerly IAAF) approved Full PUR System 400 mm 8 lane Synthetic Athletic track Surface of minimum 14.5 mm thickness in the normal stress areas including line markings as per the requirements/specifications laid down by World Athlctics and as per direction of the Engineer-in-charge. The medium stress areas should be of minimum 20 mm thickness and the High stress areas to be minimum 25 mm thickness. The track shoud be installed in supervision of an installation team of the manufacturer who have experience in such installation in india or any other country in the world. The Products should be European/ American/ Australian orgin. Make : Herculan B.V.- NED/ HELLAS CONSTRUCTION INC. 0 USA/ POLYTECH LIQUID POLYMERS LTD. - UK./ KDF/ BSGSp.Z.o.o/ Por plastic or equivalent make.
SOR Item- 4-3-2 Construction of Gravel/ Soil Aggregate Base/Surface by providing well graded material of nominal maximum size grading 10 mm as per Table 2.3 of IRC SP 77- 2008, spreading in uniform layers with tractor mount appropriate grading arrangements on prepared surface, mixing by mix in place method at OMC with tractor mount appropriate rotavator attachment and compaction with three wheel 80- 100 kN Static Roller capacity to achieve the desired density complete as per specifications contained in Para 2.2, 3.6 and 3.7 of IRC SP 77-2008.
SOR Item- 4-3-3 Construction of Gravel/ Soil Aggregate Base/Surface by providing well graded material of nominal maximum size grading 5 mm as per Table 2.3 of IRC SP 77- 2008, spreading in uniform layers with tractor mount appropriate grading arrangements on prepared surface, mixing by mix in place method at OMC with tractor mount appropriate rotavator attachment and compaction with three wheel 80- 100 kN Static Roller capacity to achieve the desired density complete as per specifications contained in Para 2.2, 3.6 and 3.7 of IRC SP 77-2008
SOR Item- 11-2-1 Providing and Fillling River Sand Rootzone in Ground as per drawing and technical specification Clause 305.3.9.
DSR Item- 2.2 Supplying and stacking of good earth at site i/c royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).
DSR Item- 2.3 Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment)
DSR Item- 2.4.1 Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm
DSR Item- 2.5 Rough dressing the trenched ground including breaking clods
DSR Item- 2.6 uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation
DSR Item- 2.7 Fine dressing the ground
DSR Item- 2.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately)
DSR Item- 2.9 Mixing earth and sludge or manure in proportion specified or directed by the officer-in-charge
DSR Item- 2.33 Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge
NSI Item- Providing and laying of 250 GSM non woven Geo-textile manufactured from high quality Propylene staple fibers on the prepared sub-grade withan overlap of minimum 300mm and an extra overlap at the edges with min 300mm including all wastage etc. Each roll of the Geo-textile should be of min 3.8m width and length covering the entire width of the ground.
NSI Item- FIFA FOOTBALL GOAL POST WITH NET Uprights & Crossbars made from 75mm x 50mm reinforced aluminium. Fully welded corner joints provide superior strength and added safety. Backbar consist of a single weighted tube with 2 puncture proof cellular rubber wheels allowing for ease of manoeuvrability. 460mm high reinforced aluminium backboard panels with extra thick impact absorbent noisereducing carpet on all inside faces. Polyester powder coated white excluding net supports and backboards which are blue. Size: 7.32m x 2.44m INCLUDING NET. Make Harrod UK or Equivalent
NSI Item- Supplying, installing, testing and commissioning of Water Sprinkler Systems of approved make as per instructions of Engineer-in-Charge for Football Ground.
DSR Item- 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
NSI Item- Supply and fixing of Perforated PVC Pipes of 200mm dia along the lateral sides of the ground in a Fish Bone Structure with end caps and couplers to join the pipes.
SOR Item- 4-2-2 Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402
SOR Item- 5-14 (Providing and laying 25 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated fine-grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces not less than 1000C, protruding 1 mm to 4 mm over mastic surface, all complete as per clause 515.)
NSI item- Supplying FIH approved global category Synthetic Hockey Surface with polyethylene fiber and cast in situ shock pad layimg jointing and fixing the same on the bituminous sub base with rubberized under layer as per the FIH requirements and the pasting of synthetic grass as per specification of the global category FIH competition including all marking on the surface as per FIH rules and standard etc. complete as per the instructions of the Engineer-in-charge. # stitches / lm 340 / lm Pile Height 12 mm, Pile Weight 1.500 gr / m² ( tolarance +- 10%) total height 14 mm.
NSI item- Providing and laying of 250 GSM non woven Geo-textile manufactured from high quality Propylene staple fibers on the prepared sub-grade withan overlap of minimum 300mm and an extra overlap at the edges with min 300mm including all wastage etc. Each roll of the Geo-textile should be of min 3.8m width and length covering the entire width of the ground.
NSI item- FIH HOCKEY GOAL POST WITH NET Uprights & Crossbars made from 75mm x 50mm reinforced aluminium. Fully welded corner joints provide superior strength and added safety. Backbar consist of a single weighted tube with 2 puncture proof cellular rubber wheels allowing for ease of manoeuvrability. 460mm high reinforced aluminium backboard panels with extra thick impact absorbent noise reducing carpet on all inside faces. Polyester powder coated white excluding net supports and backboards which are blue. Size: 3.66m x 2.14m INCLUDING NET. Make Harrod UK or Equivalent
NSI item- Supply and fixing of GeoRex Perforated PVC Pipes of Astral make of 160mm dia along the lateral sides of the ground in a Fish Bone Structure with end caps and couplers to join the pipes.
NSI item- Supplying, installing, testing and commissioning of Water Sprinkler Systems of approved make as per instructions of Engineer-in-Charge for Hockey Ground
DSR Item- 16.3.10 Supplying and stacking at site. Moorum
NSI item- Providing and Laying of FIVB Certified 8 Layer Acrylic Synthetic Cushion Court flooring including primer (layer 1), resurfacer (layer 1), Cushion (2 layers), resurfacer (layer 1), 2 layer of color, complete in all aspects as per direction of Engineer-in-charge.
NSI item- Pole with Net Providing & Fixing Aluminium Pole made of 80mm × 80mm square pipe with special internal ratchet system for tightening the net. This enables perfect tension control for the net. Top cover made from cast, Aluminium with pulley. The use of branded Epoxy Paint.
SOR Item-3-3 Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)(70 % Total Excavation)
SOR Item-3-4 Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)Ordinary rock (20 % Total Excavation)
SOR Item-11-2-2 Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 Earth filling
SOR Item-1-5 Hand Packed stone filling in back of wallls including cost of all materials, royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications)
DSR-2023 Disposal of Excavated earth/rock unserviceable, upto dumping zone near national highway distance upto 10km from site
SOR Item-2-2 Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203
SOR Item-1-4 Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203, Random rubble masonry In cement mortar (1:4)
SOR Item-1-3 Dry stone masonary
SOR Item-11-4-5 Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 R.C.C. grade M 25
SOR Item-13-1-2-B Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 (R.C.C M 25) Height 5m to 10m
SOR Item-11-8 Supplying, fitting and placingTMT bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202
SOR Item-13-3 Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202
SOR Item-12-9 Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7
SOR Item-4-1-A-2 Granular Sub-base with Well Graded Material By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading II Material
SOR Item-2-3 Cement Concrete (PCC M-30) Pavement:- Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications.
SOR Item-7-1-2 Laying Cement Concrete Pipe NP3 (burried conduits) on first class bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapets.300 mm dia.
SOR Item-2-6 Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.
SOR Item-8-2-A Cast in Situ Cement Concrete M 20 Kerb with Channel (Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M10 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCC M20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer
SOR Item-10-5 Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701
DSR Item- 2.1 Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
DSR Item- 2.2 Supplying and stacking of good earth at site i/c royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).
DSR Item- 2.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
DSR Item- 2.13 Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm refilling the excvated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of rearth after redution by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling and directed, within a lead of 50m. lift upto 1.5m complete (cost of sludge, manure or extra earth to be paid for seperately)
DSR Item- 2.14.4 Digging holes in ordinary soil and refilling the same with the exavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reductin by 8%9 flooding with water, dressing including remocal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for seperately) Holes 45cm dia and 45cm deep
DSR Item- 2.16 Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.
DSR Item- 2.19.1 Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S. (non modular) bricks of class designation 7.5
DSR Item- 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge
DSR Item- 2.54 Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge
DSR Item- 2.57.1 Trees Plant
DSR Item- 2.57.2 Shrubs Plant
DSR Item- 5.11 Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge
DSR Item- 5.13 Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.
DSR Item- 5.15 Providing and Displaying Cycus revoluta specimen , having 45 to 50 fresh and healthy, leaves having 30cm to 35cm circumfrance of base stem well developed in 40 cm challi, as per direction of the officer-in-charge.
DSR Item- 5.20 Providing and Displaying Ficus black vivion piller topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.
DSR Item- 5.22 Providing and Displaying Ficus Nuda topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge
DSR Item- 8.10 Providing and stacking of Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.
DSR Item- 8.15 Providing and stacking of Dombeya mastersii of height 60-75 cm. with 4- 5 branches in bag of size 25 cm as per direction of the officer-in-charge.
DSR Item- 8.18 Providing and stacking of Euphorbia caracasana (bronze colour leaves) of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge.
DSR Item- 8.19 Providing and stacking of Euphorbia pulcherrima (dark red double bracts) well branched of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.
DSR Item- 8.23 Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-165 cm. with 8-10 branches and healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.
NSI Item- Providing Smith Machine of standard Smith Machine Material of Frame Colled Rolled Mild SteelThickness 3 mm (12 gauge) Maximum Weight Plate Load 280 kilogram Vertical height between Bar Supports (in cm) 15 centimeter Warranty on Frame 7-year warranty on structural frame (coatings excluded) Warranty of Bearing, Guide Rods, Pulleys and Cables 1 Year Product Id: 5116877-50066858551
NSI Item- Providing VIVA FITNESS 45° Leg Press or Hack Squat Machine with Recommended Live Area, metric cm 212 x 166 x 210 Width 200 centimeter Weight Stack(s) 155 kilogram Product Weight 300 kilogram Type IT SERIES Height 150 centimeter. Length 200 centimeter Max User Weight 180 kilogram Product Id: 5116877-67618564937
NSI Item- Providing VIVA FITNESS Horizontal Pin Loaded - Chest Press Type of Chect Press Machine according to Loading Pin Loaded Type of Chect Press Machine according to Motion Horizontal Material of Frame Colled Rolled Mild Steel Thickness 3 mm (12 gauge) Maximum Weight Capacity (each side) (in kg) 100 kg (Pin Loaded) Warranty on Frame 7-year warranty on structural frame (coatings excluded) Product Id: 5116877-34300445922
NSI Item- Providing VIVA FITNESS Pectoral Fly with Max Weight Capacity of 125 kilogram Type Pectoral Fly variations/Rear Deltoid variations Pectoral Fly Material of Frame Colled Rolled Mild Steel Thickness 3 mm (12 gauge) Maximum Weight Capacity (each side) (in kg) 125 kilogram Warranty on Frame 7-year warranty on structural frame (coatings excluded) Warranty of Bearing, Guide Rods, Pulleys and Cables 1 Year Product Id: 5116877-6986746604
NSI Item- Providing turbuster Stainless Steel Barbell Rack (Vertical Barbell Holder) Frame Description Standard rubber feet protect base of the frame and prevent the machine from slipping; Urethane paint guards to protect paint; 10-12-gauge steel frame ensures maximum structural integrity; Each frame receives an electrostatic powder coat finish to ensure maximum adhesion and durability Length 46 centimeter Material Stainless Steel Maximum Capacity (Barbell) 15 kilogram Height 40 centimeter Product Id: 5116877-46736681819
NSI Item- Providing Life Fitness Pin-Loaded Lat Pull Down with Capacity of 6 kilogram Plates per Rod Type of Machine according to Motion Pin-Loaded Material of Frame Colled Rolled Mild Steel Thickness 3 mm (12 gauge) Maximum Weight Capacity 100 kg (Pin Loaded) Plate Capacity (per rod) 6 kilogram Warranty on Frame 7-year warranty on structural frame (coatings excluded) Warranty of Bearing, Guide Rods, Pulleys and Cables 1 Year Product Id: 5116877-64932071216
NSI Item- Providing Life Fitness Stainless Steel Flat Gym Bench, Warranty 12 month Bench Material Stainless SteelSeat Material Leather Warranty 12 month Certification of product Quality Test ISO 9001 Certification of Manufacturer Yes Product Id: 5116877-98203344836
NSI Item- Providing FIVE RINGS SPORTS Plate Loaded Leg Curl Machine Type of Leg Curl Machine (According to Design) Seating Type of Leg Curl Machine (According to Weight Loading) Plate Loaded Material of Frame Cold Rolled Mild Steel Thickness 3 mm (12 gauge) Maximum Weight Capacity (each side) (in kg) 200 kg (Plate Loaded) Warranty on Frame 7-year warranty on structural frame (coatings excluded) Product Id: 511687779017569467
NSI Item- Providing VIVA FITNESS Pin Loaded Leg Extension Machine Type of Leg Extension Machine (According to Weight Loading) Pin Loaded Material of Frame Colled Rolled Mild Steel Thickness 3 mm (12 gauge) Warranty on Frame 7-year warranty on structural frame (coatings excluded) Warranty on Pulleys, Guide Rods, Bearings and Cables 1 Year Product Id: 5116877-53235047011
NSI Item- Providing turbuster Automatic Steel Whole Body Vibration Unit (Machine), Warranty 1 year Material Type Steel Intensity High Hand Sensors Yes Warranty 1 year Product Id: 5116877-54426449848
NSI Item- Providing Life Fitness Integrity Series Treadmill with LED Console/Display Type LED/LCD Non-Touch (Keypad) Display Power Drive Electricity AC Motor Power 4 hp Material for frame Aluminium Alloy Material for side foot rail Aluminium Alloy Material for roller Stainless Steel Running Length (In inch) 60 to 62 Running Width (In inch) 24 Product Id: 5116877-4512928853
NSI Item- Providing cosco Elliptical Cross Trainer with Manual Brake System Weight of elliptcal cross trainer in kg 160 Type of resistance system Manual Brake System Type of screen LED ,Touch screen ,Language Option ,Upfront Position of Console (directly in front of User Face) ,Toggle for speed and Incline Screen display reading time, distance, RPM, Speed, difficulty Level, Calories, Pulse, heart beat Warranty in years 1 Adjustable paddle foot straps spacing in inch 1.8 Product Id: 5116877-82255232371
NSI Item- Providing FIVE RINGS SPORTS Weight Lifting Set consist Barbell and Collars and Plates Item Includes Barbell ,Collars ,Plates Barbell Diameter 50 millimeter Barbell Size 5 foot Barbell Material SS Plates Weight 20 kilogram Plates Material Rubber Collars Material Metal Collars Weight 2.5 kilogram Product Id: 5116877-37096020853
NSI Item- Providing turbuster Hexagonal Rubberized Weight Dumbbells 17.5 Kg Shape of dumbbells Hexagonal Weight of dumbbells in Kg 17.5 Dumbbells dimensions in cm 25 Dumbbells shall be rubber coated with steel inside Yes Warranty in years 1 Availability of test report from govt/ NABL/ILAC accredited lab covering all parameters No Product Id: 5116877-17315078254
NSI Item- Providing Aerofit Wireless 7 inch Touch LCD Upright Bike, Frame Warranty :- 2 year with Display 7 inch Touch LCD Internet connectivity WirelessWarranty SummaryFrame Warranty :- 2 year Product Id: 5116877-62237129990
NSI Item- Providing NEW FITNESS FACTORY Double Twister Machine Types of Twister Standing Type of Twister Machine according to Twists Double Twister Machine Material of Frame Cold Rolled Mild Steel Thickness 3 mm (12 gauge) Material of Handle Pipe Mild Steel Material of Rotating Disc Mild Steel Operation Mode Manual Machine Length (+/-2%) (in cm) 100 centimeter Product Id: 5116877-80206159604
NSI Item- Providing Aerofit Powder coated Stainless steel Preacher curl bench With Epoxi coating Type of coating on frame of preacher curl bench Epoxi coating Provision of Dual rear transport wheels No Provision of ABS rubber feet for floor protection Yes Warranty in years 1 Material of main frame of preacher curl bench Powder coated Stainless steel Product Id: 5116877-69174914286
NSI Item- Providing VIVA FITNESS Plate Loaded T-Bar Row Machine, Warranty 1 year Length 185 centimeter Type IT SERIES Machine Weight 95 kilogram Height 119 centimeter Product Weight 120 kilogram Width 79 centimeter Recommended Live Area, metric cm 152 x 206196 x 163 Warranty Summary1 year Product Id: 116877-1153551783
NSI Item- Providing ROXAN Powder coated Stainless steel Abdominal bench Type of coating on frame of abdominal bench Electrostatic powder coating Provision of Dual rear transport wheels No Number of levels for height adjustment 4 Warranty in years 1 Material of frame of abdominal bench Powder coated Stainless steel Thickness of seat and back rest in inches3 Product Id : 5116877-34817718609
NSI Item- Provding TURBUSTER MULTI ADJUSTABLE BENCH Material of Frame Colled Rolled Mild Steel Thickness 14 gauge Warranty on Frame (in years) 1 year Machine Product Id: 5116877-88352505021
NSI Item- Providing Aerofit Power Rack, Max Training Weight 152 kilogram Type Discovery Series Power Rack Max Training Weight 302 kilogram Max User Weight 152 kilogram Frame Description 2 x 4 (12 MM Gauge)high-tensile strength steel. All 4-side welded. Product Id: 5116877-31312942792
NSI Item- Providing Aerofit Stainless Steel Flat Gym Bench, Warranty 12 month Aerofit Stainless Steel Flat Gym Bench, Warranty 12 month Product Id: 5116877-82041915514
NSI Item- Providing IMPULSE Stainless Steel Flat Gym Bench, Warranty 12 month Bench Material Stainless Steel Seat Material Leather Warranty 12 month Certification of product Quality Test ISO 9001 Certification of Manufacturer Yes Product Id: 5116877-34864988587
NSI Item- Providing AVON Double Tier Dumbbell Rack Capacity 750 kilogram Height 81 centimeter Type Double Tier Dumbbell Rack Length 72 centimeter Width 248 centimeter No. of Dumbbell(Pair) Rack accommodates, (2-25kg) dumbbells 10 Max Capacity 750 kilogram Warranty, Max 1 year Product Id: 5116877-32199611752
NSI Item- Providing KRISHTHA Circular Cafeteria Chair Without Armrest. Gem Id- 5116877-83805799475
NSI Item- Providing KRISHTHA Square Cafeteria Table with Seating Capacity of 4 Person.s Gem Id- 5116877-89401237911
NSI Item- GODREJ INTERIO Commercial Board Bedside table Gem ID- 5116877-35927091949
NSI Item- KRISTHA Non-Revolving &Non Tilting Chair with armrst. Gem Id- 5116877-42867098730
NSI Item- V J Interior Wooden Single Bed Storage Box Opening From Top 1905 915 40 Gem Id- 5116877-67444485919
NSI Item- SINGLE SPRINGFIT Spring Mattress Dimensions1829 mm X 914 mm Gem Id- 5116877-67402458943
NSI Item- MJ Enterprises Almirah Steel wardrobe(having cloth hanging provision) Gem id: 5116877-13668582840
NSI Item- Unbranded Polyster Plain Door Curtains (8.5-9ft x 3.5-4ft ) Gem Id- 5116877-92255417619
NSI Item- Unbranded Polycotton Single (1 bedsheetand 1 pillow cover) Bed Sheets-Handicraft Gem Id-5116877-74058991340
NSI Item- Kurlon Pillow - Synthetic Gem id: 5116877-5249460195
NSI Item- GODREJ INTERIO Rectangular CENTRETABLE with Medium Density FiberboardTop of 965mmX457mm Gem ID- 5116877-2269304187
NSI Item- Providing VASSIO 6 Seater Sofa With Leatherite Cover Gem Id- 5116877-84274052232
NSI Item- GODREJ INTERIO 3 Seater Sofa With Leatherite Cover Gem Id- 5116877-73141994564
NSI Item- GODREJ INTERIO 2 Seater Sofa With Fabric Cover Gem id: 5116877-81109799937
NSI Item- Providing Nova Translucent /Light Filtering Roller Blind. Gem Id- 5116877-79803458911
NSI Item- Providing Steel Clothes Lockers with 12 lockers. Locking arrangement (with duplicate Key) Internal locking arrangement (for 6 and 8 locker type) Welding Steel sheet material Cold reduced carbon steel sheet conforming to CR0 grade of IS 513:2016 (with latest amendment) Handle of each door made up of Anodized Aluminium Hanging rod. Gem id- 5116877-91230228962.
NSI Item- GODREJ INTERIO Revolving Chair With Arm Knee tilt Synchronic mechanism. Gem id-5116877-1353676772
NSI Item- GODREJ INTERIO Revolving Chair With Arm Only Revolving without tilting mechanism Gem Id-5116877-70675983400
NSI Item- GODREJ INTERIO Executive Table with One side E.R.U unit GODREJ INTERIOR (Godrej Interio Finnesse Table-5026 + ERU 3616 LHS) Gem id- 5116877-43935975306
NSI Item- KRISHTHA change room table (1650 L x 750 W x 700 H)
NSI Item- SR 1500 mm X 450 mm X 750 mm ( With one shelf ) Modular Side Storage Unit Gem id-5116877-19822696701
NSI Item- wesource Medium-density fibreboard (MDF) Matte Study Or Laptop Table, Warranty 3 year. Gem id-5116877-32750585829
NSI Item- GODREJ INTERIO Executive Table with One side E.R.U unit Gem id: 5116877-88554411717
NSI Item- GODREJ INTERIO Revolving Chair With Arm Synchronic tilt mechanism Gem id: 5116877-41314003521
NSI Item- GODREJ INTERIO Single Seating and Dual Seating 36 Mm Thick Three Layer Prelaminated Particle Boards Of Grade-II Type-II Of IS:12823/Latest Modular Extendable Conference Table Gem Id- 5116877-90710041722
NSI Item- HARSHNIL INDUSTRIES Almirah Steel shelving cabinets Gem Id- 5116877-63864297292
NSI Item- R.K. CRCA Sheet Perforated Patient CareBeds (1950-2050mm Length & 900-920mm Width) Gem Id- 5116877-31230393596
NSI Item- SLEEP WELL MATTERESS poly urethanepatient care mattresses, Length 1830 mm(6feet) Gem Id- 5116877-17352336756
NSI Item- GENTEK Semifowler Patient Bed (2050-2100mm Length & 900-950mm Width) Gem Id- 5116877-76370075597
NSI Item- Shikha Surgicals poly urethane patient care mattresses, Length 2135 mm(7 feet) Gem Id- 5116877-13787964028
NSI Item- Bed side table Gem Id- 5116877-94493677896
NSI Item- GODREJ INTERIO Revolving Chair withSwivel tilt mechanism Gem Id- 5116877-8818260202
NSI Item- KRISHTHA MODULAR TABLE L X D & H 1500millimeter X 900 millimeter 750 millimeter Gem Id- 5116877-88021356390
NSI Item- UPICA Cotton Plain Door Curtains Gem ID- 5116877-86492944260
NSI Item- SFG DEEPIKA Mattress protector cum bedsheets for hospitals 240 centimeter 150centimeter
NSI Item- THE JASMINE PEARL Wooden Double Bed Storage Box Opening From Top 2000 1525, 100 Gem Id- 5116877-79301526456
NSI Item- JAKFUR Wooden Single Bed Storage Box Opening From Top 1830 915 350
NSI Item- KRISHTHA Single Layer Foam Mattress - Size 1829 mm x 889 mm Gem ID- 5116877-22399232229
NSI Item- KRISHTHA Three Layers Foam Mattress -Size 1905 mm x 889 mm Gem ID- 5116877-83566137362
NSI Item- VASSIO 5 Seater Sofa With Fabric Cover Gem ID-5116877-87861546469
NSI Item- ALDER Wood Antique Dining Tables Gem Id- 5116877-74687794780
NSI Item- Providing KRISHTHA 6 seaters Table Rectangular Shape 1800 mm Lengthx 800 mm Table Height Gem Id- 5116877-46212419366
NSI Item- Providing KRISHTHA 900 mm wide 1905 mm highMetal Shelving Racks Gem Id- 5116877-44124370428
NSI Item- NEXT FURNITURE SOLUTION Laboratory Steel Furniture Island bench with table top, Size of side benches/Island benches (LxWxH)- 1500 mm X 750 mm X 900 mm Gem Id-(5116877-71852967570)
NSI Item- Unbranded Square Wooden Lab Stools 460mm X 300 mm 75 Kgs
Electrical work DSR 1.10.3 Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-C
DSR 1.10.2 Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-B
DSR 1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
DSR 1.13 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
DSR 1.40 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
DSR 1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
DSR 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
DSR 1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
DSR 1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
DSR 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
DSR 1.18.2 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair
DSR 1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
DSR 1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
DSR 1.12 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
DSR 1.21.1 20 mm
DSR 1.21.2 25 mm
DSR 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
DSR 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
DSR 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
DSR 2.5.1 Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 4Way (4+12), Double door
DSR 2.5.2 Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 8Way (4+24), Double door
DSR 2.4.2 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6way 4+18 Double Door
DSR 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral
DSR 2.10.1 Single pole
DSR 2.10.2 Single pole and neutral
DSR 2.10.5 Triple pole and neutral
DSR 2.13 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
DSR 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
DSR 5.7 Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
DSR 5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
DSR 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
DSR 10.18 civil P/F Hexagonal MS sheet fan box for ceiling fan clamp od internall dia 140mm, 73mm height top lid of 1.5mm thick MS sheet with its top surface hacked, MS clamp shall be made of 12mm dia MS bar bent to shape as per standard design.
DSR 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
DSR 1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
DSR 1.24.1 5/6 A switch
DSR 1.24.4 3 pin 5/6 A socket outlet
DSR 1.24.6 Telephone socket outlet
DSR 1.24.7 TV antenna socket outlet
DSR 1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module
DSR 1.40 Providing and fixing plain 16/0.20mm (0.50sqmm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as required.
NSI Supplying and fixing of LED high bay light 200 watt made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics Ascentech R (AT HB 200)
NSI Heigh Bay LED Light 100 W Ceiling mounting type Acentech AB_HB_100
NSI Supply & fixing of 4ft Linear robust LED IP20 batten with system lumen output of 4000 lumens. The minimum system efficacy should not be less than 120 lm/w @6500K. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50. The luminaire should have a color temperature of 6500K and CRI>80, SDCM<=5. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The Luminaire should have 4KV surge for better protection against voltage fluctuation/spikes. The luminaire housing should made of polycarbonate extrusion with a High Transmittance PC Diffuser. The total power consumption should not exceed 34W (including driver). Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. Luminaire manufacture shall provide LM79 and LM80 report from NABL/UL accredited lab & LM80 report issued by LED manufacturer. Both the fixture and Driver should be of same make & must have separate BIS approval and the certificates must be submitted for records.
NSI 36/40 w LED batten tube surya 40 w 6500 L LED
NSI 300mm Bajaj propeller type ventlating fan with bird screen Freshee 300mm
DSR 19.10 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
NSI Supply, Installation, Testing and Commissioning of 450 mm wall fan with regulator Bajaj Esteem
NSI Supply & Fixing of IP20 recessed LED Downlighter made of pressure die cast aluminum housing with PC diffuser, Fixture should have minimum efficacy at System level (Not Chip Level) >=100 lumens/watt with Minimum system Lumens 1200 with maximum system wattage of 12W. Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 4000K/6500K (SDCM<5), CRI >80, PF >0.95, THD<10% (At Full Load) working temp range - 0°C < Ta < 45°C, and operating Voltage Range of 130-320 VAC. It should has a Minimum Internal Surge Protection of 2.5KV. Electronic Switchable ballast. The Luminaire shall be Class B serviceable, it shall have cutout dia of 150mm and product height not more than 40mm. philips dn296
NSI Supply & fixing of 4ft Linear robust LED IP20 batten with system lumen output of 2000 lumens. The minimum system efficacy should not be less than 120 lm/w @6500K. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50. The luminaire should have a color temperature of 6500K and CRI>80, SDCM<=5. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The Luminaire should have 4KV surge for better protection against voltage fluctuation/spikes. The luminaire housing should made of polycarbonate extrusion with a High Transmittance PC Diffuser. The total power consumption should not exceed 16W (including driver).
NSI Supply & fixingof recessed mounted 2X2 LED panel ,made of CRCA housing with high efficiency PS Diffuser. LED Used shall be SMD type and fixture should have minimum efficacy at System level >=120 lumens/watt with Minimum system Lumens 4200lm & Max System wattage of 35W, Life of fixture : 50000 burning Hrs. @ L70B50 Lumen maintenance @45deg,CCT-4000/5700/6500K, (SDCM<=5), CRI Ra >=80, THD ≤10%, PF ≥0.95, an operating Voltage Range of 140 - 270 VAC.Minimum Internal Surge Protection 3.5kV & IP20/IK02 protection, Fixture should comply with to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, IEC 60598-2-2. The product shall be of class B serviceability,Signify (Philips) Cat No. RC380B LED42S-5700 G6
DSR 1.41 Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
DSR 1.44 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
DSR 1.50.1 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building LT Panel as per specification mentioned below
INCOMER
- 200 amps 36 KA FPMCCB . -1
OUTGOINGS
- 100 amp 30 KA FP MCCB -2 no., - 125 amp 36 KA FP MCCB-2 nos
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building LT Panel as per specification mentioned below
INCOMER
250 A, FP, MCCB ,36 KA - 1 No. ..
METERING & INDICATION
ON/OFF phase indicating lamps with control fuses.
Multifuction Meter
BUS BAR-as per SLD
400 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
OUTGOINGS
Outgoing - 100 amp 16 KA TP MCCB -5 no.,Outgoing - 150 amp 16KA TP MCCB-2 nos &Outgoing - 100 Amp 30KA FP MCB- 1 nos.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated with CT PTs , Multifunction Meter,required Operating Handels and Mech. Interlocking fot Bus coupler MCCB
Building LT Panel as per specification with TP&N 500 amps BUS Bar
INCOMER
800 A, TP, MCCB ,50 KA - 1 No. ..
OUTGOINGS
Outgoing - 200 amp 36 KA FP MCCB -8no.,Outgoing - 400 amp 50KA FP MCCB-1 nos & Outgoing - 100 Amp 30KA FP MCB- 6nos.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated with CT PTs , Multifunction Meter,required Operating Handels and Mech. Interlocking fot Bus coupler MCCB
Building LT Panel as per specification with TP&N 600 amps BUS Bar
INCOMER
400 A, FP, MCCB ,50 KA - 3 No. ..
OUTGOINGS
Outgoing - 200 amp 36 KA FP MCCB -3 no.,Outgoing - 125 amp 36KA FP MCCB-1 nos &Outgoing - 100 Amp 30KA FP MCB- 3nos.
NSI 'Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated along with CTs and PTs for metering with Multifunctions and operating Handles etc. as reqd.
Building LT Panel as per specification mentioned below
INCOMER
400A, FP, MCCB ,50 KA - 3No.
600 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
OUTGOINGS
Outgoing - 100 amp 30 KA FP MCCB -8 no.,Outgoing - 200 amp 36KA FP MCCB-2 nos.
NSI 'Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated along with CTs and PTs for metering with Multifunctions and operating Handles etc. as reqd.
Building LT Panel as per specification mentioned below
INCOMER
250A, FP, MCCB ,50 KA - 3No.
300 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
OUTGOINGS
Outgoing - 100 amp 30 KA FP MCCB -3no.,Outgoing - 200 amp 36KA FP MCCB-1 nos.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated along with CTs and PTs for metering with Multifunctions and operating Handles etc. as reqd.
Building LT Panel as per specification mentioned below
INCOMER
250A, FP, MCCB ,50 KA - 3No.
300 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
OUTGOINGS
Outgoing - 100 amp 30 KA FP MCCB -3no.,Outgoing - 200 amp 36KA FP MCCB-1 nos.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated with CT PTs , Multifunction Meter,required Operating Handels and Mech. Interlocking fot Bus coupler MCCB
Building LT Panel as per specification with TP&N 600 amps BUS Bar
INCOMER
400 A, FP, MCCB ,50 KA - 1 No. ..
OUTGOINGS
Outgoing - 200 amp 36 KA FP MCCB -3 no.,Outgoing - 125 amp 36KA FP MCCB-1 nos &Outgoing - 100 Amp 30KA FP MCB- 2nos.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Distribution Bus Box fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. bus box shall be suitable for accomodating 8 nos Energy Meters as per UPCL Norms with a loose wire box and sealable bus bar Chamber. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building l as per Meter Bus Box as per specification mentioned below
BUS BAR 100 amps TP&N
2 nos 60 amps three Phase Energy meters and 2nos 60 amps Single phase energy meters
OUTGOINGS
Outgoing - 63 amp 16 KA FP MCB -2no and 1 nos 40 ampsDP MCB.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Distribution Bus Box fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. bus box shall be suitable for accomodating 8 nos Energy Meters as per UPCL Norms with a loose wire box and sealable bus bar Chamber. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building l as per Meter Bus Box as per specification mentioned below
BUS BAR 100 amps TP&N
2nos 60 amps Single phase energy meters
OUTGOINGS
Outgoing - 63 amp 16 KA FP MCB -1no and 2 nos 40 ampsDP MCB.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Distribution Bus Box fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. bus box shall be suitable for accomodating 8 nos Energy Meters as per UPCL Norms with a loose wire box and sealable bus bar Chamber. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building l as per Meter Bus Box as per specification mentioned below
BUS BAR 100 amps TP&N
2nos 60 amps Single phase energy meters
OUTGOINGS
Outgoing - 63 amp 16 KA FP MCB -1no and 2 nos 40 ampsDP MCB.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building LT Panel as per specification mentioned below
INCOMER
- 200 amps 36 KA FPMCCB . -1
OUTGOINGS
- 100 amp 30 KA FP MCCB -1 no., - 125 amp 36 KA FP MCCB-1 nos
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated
Building LT Panel as per specification mentioned below
INCOMER
100 A, FP, MCCB ,36 KA - 1 No. ..
METERING & INDICATION
ON/OFF phase indicating lamps with control fuses.
Multifuction Meter
BUS BAR-as per SLD
400 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
OUTGOINGS
Outgoing - 100 amp 16 KA TP MCCB -5 no.,Outgoing - 150 amp 16KA TP MCCB-2 nos &Outgoing - 100 Amp 30KA FP MCB- 1 nos.
NSI 'Supply,Installation, testing and commissioning of Air Circulation wall mounted fan with metallic fastners, including wiring the standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
NSI 36 w 2 x 2 LED panel crompton CGCEL panel
NSI Providing Gyser (water Heater) 15 Liter Capacity. 5 Star Candes
DSR 2.11 S/F single pole blanking plate in the existing MCB DB complete etc. as required. (4 no. /MCBDB)
DSR 2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
DSR 2.20 Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
DSR 1.57 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. For AC
NSI Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate One Module for modular switches in recessincluding supplying and fixing Anchor Cat-6 Data Information Outlet, crimpling, connection, testing etc. as required.
DSR 1.53.2 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run
NSI Supplying installation testing commissioning of 24 Port, Gigabit Data switch Dlink with 2 U rack , cable maneger etc as reqd.
NSI 10W LED Batten Wipro Garnet D631065 Polycarbonate 6500K
DSR 2.3.2 Supplying and fixing 8 way, Double Door single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
NSI Supply of 18W Inverter LED pr batten with backup 8 hrs
DSR 2.2.13 Providing and fixing of 100 amps 30 KA Four pole rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required
DSR 2.2.15 Providing and fixing 200 amps 36 KA breaking capacity Four pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required
DSR 6.20 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
DSR 6.70 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
DSR 6.80 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run
DSR 6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I.bolts, nuts, chuck nuts and spring washers etc. complete as required.
DSR 6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
NSI Supply & fixing of Heavy duty bulkhead surface type lighting fixture 10W - 1100lm made up of pressure die-cast aluminium housing and Polyster Powder coated die cast aluminium with High quality polycarbonate diffuser in opal finish for glare free light distribution.High efficiency long life LED module with SMD LED package mounted on MCPCB with lumen efficacy of >100 lm/W. Powered by integral electronic LED driver with CCT 6500, CRI>80,THD<10%, PF>0.9, IP66, IK 09, Life class of 50,000 hrs @ L70, Operating Temperature: 0 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. Driver Safety requirement standards:IS 15885. philips wt202
NSI Supply and fixing of decorative fancy wall bracket fitting
NSI Supplying and fixing of wall bracket
External Work
NSI Supplying,installation,testing and commisioning of 850 KVA 11kV/0.433 kV outdoor Package type compact substation equipments comprising HT Panel, Transformers, HT cable, Bus trunking from Transformer to LT Panel, LT Panel, Automatic Power factor correction panel, Active Harmonic Filters,TVSS (Transient Voltage suppression system), SPD (Surge protection system), Essential panel,Earthing,required inter-connections, substation safety euipments including LT cabling from sub station to the buildings fed by the sub station.
NSI S/F XLPE insulated screened PVC beded galvanized steel strip of wire armoured electric power cable (heavy duty) with aluminium conductor 11KV grades cross sectional area 300 sqmm as per diected by engineer-in-charge. For metering eqpt.
DSR 5.40 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
DSR 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe From earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
DSR 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
DSR 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
DSR 9.10 Supplying and making end temination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed /XLPE aluminium couductor cable of 1.1 KV grade as required.
DSR 9.1.29 3.5 x 240 sq. mm
DSR 10.5.4 S/M OUTDOOR cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required: upto 300 sq. mm
DSR 10.4.4 supplying and making indoor cable end termination with heatshrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core,300 sq.mm, XLPE aluminiumconductor cable of 11 KV grade as required :
DSR 13.13 S/E of three piece nonlinear resistor type lighting arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharege current rating of 5 KV and complete with galvanised clamping arrangenment, G.I. bolts, nuts, washers etc. as required.
NSI SITC of OutDoor Type, Double Door Feeder Pillar with minimum 2mm thick MS sheet 7 Tank treatment powder coated Painted with Sloping Canopy suitable size of TPN Aluminium Bus Bar, Earth Bar,Pad locking arrangement, LED Indication Lights, Detachable Gland Plate, fixed on CC Foundation with making suitable CC foundation capable to accomodate the following MCCBs, Interconnection etc. as reqd.
400 A,50KA,FPMCCB 1 no
125A,36KA,FPMCCB 9 nos
200 A,36KA,FPMCCB- 2no
250 A,50KA,FPMCCB 1 no
125A,36KA,FPMCCB 1 nos
100 A,30KA,FPMCCB 9nos
100 A,36KA,FPMCCB 4 nos.
200 A,36KA,FPMCCB 1 no
630A,50KA,FPMCCB 1no.
400 A 50KA FPMCCB 3nos
200 A 36 KA MCCB 2 nos
NSI 6 meter GI octegonal pole single arm with loop in box Bajaj
DSR Erection of Octagonal street light pole of 6 to 8 meter length in RCC 1:2:4 foundation including excavation, refilling, Reinforcement etc. as per Pole Manufacture design.
NSI Supply & Fixing of high-quality integrated LED Street Light with a minimum system lumen of 8400 lm and system wattage not exceeding 60W with a nominal system efficacy of 140 lumen/watt. The LED used shall have CCT of 5700K, SDCM ≤ 5 and CRI≥70. The housing should be made of Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” & shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved & should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. The product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 & impact resistance shall be IK10. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 10 KV/5KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 5KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only & shall be from either Lumileds, Osram, Nichia, Cree & APT Electronics make or equivalent. The Driver should be asphalt potted & should be a BIS approved driver. The driver shall have operating voltage of 120V to 270V, PF≥0.95 (@ full load), THD≤10% (@ full load). The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547 & IEC 61000-3-2. The luminaire brand name shall be embossed/engraved on the luminaire/end plate & not screen printed or put using sticker. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Similar to above Specs in Philips BRP501
NSI SITC 12 mtrs high Mast with 6 nos of 400 watt Flood light including civil works etc as reqd. Make - Philips/Valmont/Transrail
NSI SITC of 30 meter high Octagonal GI355 gradeasper BSEN10 025 Hgh mast Stedium Lighting Tower having Mountin Framecapable of mounting 50 nos 400 W Areana Flood light Luminaries including civil foundation work, Conneting Copper cables from MCBs , Cubical type Control Panel, etc as required as per GEM Item Provisions. Make Philips/Valmont/Transrail
NSI Supply & Fixing of high-quality integrated LED Flood Light with a minimum system lumen of 70000 Lm and system wattage not exceeding 500W with a nominal efficiency 140 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI : 70. The housing should be of non-corrosive high-pressure single piece die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. with PF > 0.95. Lifetime of 75K hours @L70 at 35deg C ambient temperature. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/ replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate. While accessing the gear compartment, the optical compartment should not be accessible. The Luminaire should have a 20 KV /10 KA SPD duly bolted in the Luminaire and 4KV internal surge protection. The input voltage range will range from 120-277V AC. The SPD should be able to sustain a minimum 15 hits of 10KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3.5 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The LED used in the luminaire shall be SMD type only of make Lumileds, Osram, Nichia, and CREE & no other make. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be a asphalt potted driver not a printed circuit board without casing, mounted inside the luminaire & it should be of same make. Both driver and luminaire should have BIS Approval. Similar to Philips BVP485
NSI Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade aluminium conductor armored of following size in the existing RCC/ HUME/ METAL pipe,in Duct trench/cable tary etc. as required.
2x6 sq.mm
2x16 sq.mm
4X16 Sq.mm.
3.5x35 Sqmm
3.5x70 Sqmm
3.5x95 Sq.mm
3.5x120 sq.mm
3.5x 185 Sq.mm
3.5x240 Sqmm
3.5x300 sq.mm
DSR 14.13 Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required
DSR 14.13.2 80mm
DSR 14.13.3 110mm
DSR 14.13.5 150mm
DSR 14.14.4 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required
DSR 14.16 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
DSR 14.16.1 63mm
DSR 14.16.2 90mm
DSR 14.16.4 160mm
DSR 4.10 Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays with perforation not morethan 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts& nuts, painting suspenders etc as required.
DSR 4.10.4 300 mm width X 50 mm depth X 1.6 mm thickness
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated with CT PTs , Multifunction Meter,required Operating Handels and Mech. Interlocking fot Bus coupler MCCB
Building LT Panel as per specification with TP&N 1600 amps BUS Bar
INCOMER
1600A, FP ACB ,55 KA - 2 No. ..
OUTGOINGS
Outgoing - 200 amp 36KA FP MCCB -4no., Outgoing - 400 Amp 50KA FP MCB- 3nos. Outgoing - 630 amp 50KA FP MCCB -3no., Out going 800 amps 50 KA FP MCCB 1 no.
NSI Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated with CT PTs , Multifunction Meter,required Operating Handels and Mech. Interlocking fot Bus coupler MCCB
Building LT Panel as per specification with TP&N 1000 amps BUS Bar
INCOMER
800A, FP MCCB ,55 KA - 1 No. ..
OUTGOINGS
Outgoing - 200 amp 36KA FP MCCB -3no., Outgoing - 400 Amp 50KA FP MCB- 1nos. Outgoing - 630 amp 50KA FP MCCB -1no., Out going 100 amps 30 KA FP MCCB 3 no.
PAR 6.3.1 Supply, Installation, testing and commissioning of Salient Type DG set, AMF Panel, bus ducting/ cables from DG set to Essential Panel, Synchronising Panel if reqd., DG set Enclosure room sound insulation, ventilation, smoke exhaust, Earthing of DG set System, control cabling, fuel Tank piping,exhaust chimney and piping,as per CPCB norms, civil works connected with DG sets, including foundation etc. as reqd.
PAR 3.1.1 Supply ,installation testing and commissioning of 8 Pessenger (544Kg.) Machine Room less lift having contract speed of 1.0 meter per second serving five different floors G+4, doors opening all on one side, with VAVF cotroller, having ARD with Dry MF batterirs, Microprocessor based simples slective collective with attendent operations,415 V 50 Hz 3 phase 4 wire power, with power operated centre opening horizontal sliding stainless steel scrach free car and landing doors, infra red curtain and one hour fire rating, with overload waring indiactor, concealed luminary with LED light, axial pressure ceiling fan, with voice annoucement system. etc as required.
PAR 3.1.3 Supply ,installation testing and commissioning of 13 Pessenger (844Kg.) Machine Room less lift having contract speed of 1.0 meter per second serving five different floors G+4, doors opening all on one side, with VAVF cotroller, having ARD with Dry MF batterirs, Microprocessor based simples slective collective with attendent operations,415 V 50 Hz 3 phase 4 wire power, with power operated centre opening horizontal sliding stainless steel scrach free car and landing doors, infra red curtain and one hour fire rating, with overload waring indiactor, concealed luminary with LED light, axial pressure ceiling fan, with voice annoucement system. etc as required.
PAR 6.4.1 Supplying, installation, testing and commissioning of online 3 phase UPS System with 30 minutes back up including batteries, interconnecting cables, battery racks etc.
PAR 6.17.1 Supplying, installation, testing and commissioning of IP based EPABX System comprising of Core switches & L2 switches with 10 G, 10 Giga SFP modules, Industry Standard Appliance Server, Cloudbased, enterprise-grade UC Solution, MID/ENTRY Level IP/SIP Phone with, Dual 1 Gig Ports, Racks, CAT 6A cable, Patch Panels, OFC etc.
PAR 6.18 Supplying, installation, testing and commissioning of Audio-Visual System complete with all Arrangment.
DSR 15.10 Supplying,installation,testing and commissioning of PassiveInfrared (PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable forconnected load upto 10Amp , for mounting height up to 2.8mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.
DSR 15.20 Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc.
DSR 15.40 Supplying,installation,testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required.
15.40.2 2 outpurt per phase.
PAR 6.17.1 SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM
Supply,Installation,Testingand Commissioning of on grid Solar Photovoltaic PowerPlantconformingtoMNREspecificationsasamended,consistingofMono/PolyCrystallinesiliconsolarcells,netmeteringfacility,necessaryprotections,earthing,mountedonAluminium/GIstructureofsuitablestrengthwithfollowingcomponents complete as required:-
a)SolarPhotovoltaicModuleofcapacity330Wporabove,manufacturedinIndia,conformingtoIS14286/IEC61215,IS/IEC61730-Part-1,IS/IEC61730-Part-2.SolarPhotovoltaicModuleconversionefficiencyshallnotbelessthan16.5%.PVmodulesusedinsolarpowerplants/systemsmustbewarrantedfortheiroutputpeakwattcapacity,whichshouldnotbelessthan90%attheendof10yearsand80%attheend of 25 years.
b)PowerConditioningUnit(PCU) of 350-00VDC Input voltagerangeand400VAC,threephase,4wire,50Hz+/2.5Hz,outputvoltagesuitabletogenerateACPowerwith efficiency not lessthan 97%, total harmonic distortionless than3% and suitable forambient temperature from 0 to 50 degreeC. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.
c) Data Monitoring System complete with accessories.
d)FixingofArrayjunctionbox&MainjunctionboxwithIP65protectionandterminationarrangementforincomingandoutgoingcablealongwithglands,lugsand other accessories etc. as required.
e) Lightning and surge voltage protection.
f)Connections&Interconnectionsbysupplying&fixingrequiredsizeXLPEinsulatedcopperconductor1.1kVgradearmouredpowerandcontrolcablesbetweensolarmodules,mainpowercabletogridsupplyPCUunitalongwithsupplying&fixingofnecessarychannel/conduitlugsandotheraccessoriesetc.asrequired.
Remark Solar inverter has 6 yr warranty, Solar panel have 10 yr warranty, AMC is required after 6 yr, 1 Array will have 10 panel connected in series, Connection 1 array have 10 panels in series 240 volts DC, 10 amp, Connection 10 array output in parallel 240 volts 100 amp DC, Connection output 2 parallel array in series 480 volts 100 amp.
PAR 6.9.1 Supplying, installation, testing and commissioning of solar water heating system with heat exchanger type including , make up water tank and piping etc,
NSI Supply & Fixing of all in one integrated LED solar streetlight consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, PIR sensor, inter-connecting cables and pole mounting piece integrated into the luminaire as a single unit. Solar street light with IP65 ingress protection having a system wattage of maximum 17W with minimum 3000 lumen output, 35Wp high efficiency monocrystalline solar panel, highly efficient MPPT based charge controller and 12.8 V, 20 Ah Lithium Ferro Phosphate (LiFePO4) battery with proper battery management system. LED lumen efficacy shall be at least 175lm/W and LED driver should have >90% efficiency. Typical correlated colour temperature should be 5700K with CRI>70. It should have a PIR sensor to ensure battery optimisation with help of a suitable dimming profile. The luminaire should be housed in IK 08 impact resistance certified single piece aluminium pressure diecast housing with anti-corrosive coating and must have a UV stabilized polycarbonate cover. The housing should be made in India. The luminaire shall have a specially designed pole mounting piece that enables lateral as well as post top mounting and installation at varying tilts from 0 to 15 degrees for optimal light distribution. The product shall comply to IEC60598-2-3 for Safety of Luminaire for Road and Street Lighting, IEC 62109-1 for Safety of Power Converters used in solar Panel Equipment, IEC 61547 for EMC immunity requirements, CISPR 15 for Radio disturbance characteristics, IEC 62133 & UL1642 for Safety of Lithium Ferro Phosphate Battery and IEC 61730-1,2 & IEC 61215 for Safety of Solar Panel Module.
Wet Riser for fire fighting
DSR 18.10 Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automaticoperation and consisting of following, complete in allrespects, as required (a) Horizontal type, multistage, centrifugal, split casingpump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical seal conforming to IS 1520.
(b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operationon 415 volts, 3 phase 50 Hz, AC supply with IP 55protection for enclosure, horizontal foot mounted typewith Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered
2280LPM at 88 mtrs Head
DSR 18.20 Supplying, installation, testing and commissioning ofdiesel engine driven main fire pump suitable forautomatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump)
Horizontal type, multistage, centrifugal pump of cast ofiron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.
Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thickaluminium sheet cladding, residential silencer,instruments and protection as per standard specification, stop solenoid for auto stop in the event offault with audio indications, painted with post office redcolour etc. as required.
M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plasteredand with anti vibration pads.
2280LPM at 88 mtrs Head
DSR 18.30 Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.
suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.
180 LPM at 88 mts head
DSR 18.4 Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical confirming to IS : 1520Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325 .M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as requiredSuitable cement concrete foundation duly plastered and with anti vibration pads.
DSR 18.4.2 450 lpm at 35 m Head
DSR 18.5 Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect,
suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :
All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification
DSR 18.6 Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.
18.6.2 150mm dai
DSR 18.7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including,Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthatic enamel paint of required shade complete as required :
DSR 18.7.1 25 mm dia
DSR 18.7.2 32 mm dia
DSR 18.7.3 40 mm dia
DSR 18.7.4 50 mm dia
DSR 18.7.5 65 mm dia
DSR 18.7.6 80 mm dia
DSR 18.7.7 100 mm dia
DSR 18.7.9 200 mm dia (wall thickness 6.3 mm)
DSR 18.7.8 150 mm
DSR 18.9 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :
DSR 18.9.2 Single headed Stainless steel
DSR 18.10 Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :
DSR 18.10.2 Single headed Stainless steel
DSR 18.11 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :
DSR 18.11.1 40mm
DSR 18.11.2 50mm
DSR 18.11.3 65mm
DSR 18.11.4 80mm
DSR 18.11.5 100mm
DSR 18.11.6 150mm
DSR 18.12 Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required
DSR 18.12.4 80mm
DSR 18.12.5 100mm
DSR 18.12.6 150mm dai
DSR 18.12.7 200 mm dai
DSR 18.13 Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.
DSR 18.14 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required
DSR 18.14.4 80mm
DSR 18.14.5 100mm
DSR 18.14.7 150mm dai
DSR 18.15 Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.80mm
DSR 18.15.2 100 mm
DSR 18.15.4 200mm
DSR 18.16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required
DSR 18.16.2 Stainless Steel (Grade 304)
DSR 18.17 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
DSR 18.17.1 30 mtrs
DSR 18.18 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required
DSR 18.18.2 Stainless Steel (Grade 304)
DSR 18.19 Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required
DSR 18.19.1 2 way-100 mm dia M.S. Pipe
DSR 18.20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
DSR 18.21 Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :
DSR 18.21.1 Pendent Sprinkler
DSR 18.21.2 Upright Sprinkler
DSR 18.21.3 Horizontal Side wall
DSR 18.21.4 Concealed sprinkler
DSR 18.22 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
DSR 18.23 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.
DSR 18.23.1 100mm
DSR 24 Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/ sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasketetc of follwing sizes as required :
DSR 24.20 100 mm
DSR 18.25 Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.
DSR 18.25.1 700mm
DSR 18.25.2 1000mm
DSR 18.25.3 1200mm
DSR 18.25.4 1500mm
DSR 18.29 Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required
DSR 18.48 CIVIL Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
FIRE EXTINGUISHERS
NSI Providing and fixing carbon-di-oxide fire extinguishers trolley mounted with all accessories internal discharge tube,high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:2878 Finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.
Capacity 22.5 Kg.
NSI Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders)
Capacity 4.5 Kg.
NSI Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.
4 kg. capacity
NSI Providing & fixing carbon steel Fire man axe with rubber insulated handle tested to 20000 volts.
NSI Providing and fixing Mechanical foam ( AFFF) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.
Capacity 9 Ltr.
NSI Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm, suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site.
NSI Fixed clean agent gas based fire supression units 30 kg with 30 metrs Heat sensitive pipe Cease fire brand
MOEFA&PA+TB SYSTEM and AD&FA
MOEFA & Talkback PA System
DSR 17.1.10 Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. 10 Zone panel for fire alarm system 250 Watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required - 2 Nos.(one to act as standby) Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos.talk back unit -1 set.
DSR 17.1.9.1 Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required 4 zone
DSR 17.2.5 Supplying, installation, testing & commissioning of response ndicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
DSR 17.2.4 Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.
DSR 17.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required.
DSR 17.2.6 Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.
DSR 17.1.8 Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required
DSR 17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.
DSR 17.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required
DSR 17.3.4 Supplying, installation, testing & commissioning ofceiling/wall mounted loud speaker, 3/1.5 Watt in ABSenclosure complete as required
DSR 17.3.7 Supplying, installation, testing & commissioning of digitalaudio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.
DSR 17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required
Intellegent Fire detection and alarm System
DSR 17.2.1 Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM),
DSR 17.2.1 Ten loop Panel
DSR 17.2.2 Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.
DSR 17.2.3 Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.
DSR 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required.
DSR 17.2.8 Supplying, installation, testing & commissioning of intelligent aspiration detector for area coverage of minimum 5000 sq.ft. complete as required
DSR 17.2.9 Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
DSR 17.2.10 Supplying, installation, testing & commissioning of addressable fire control module complete as required.
DSR 17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.
DSR 17.2.11 Supplying, installation, testing & commissioning of addressable phone control module complete as required.
DSR 17.2.12 Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required
DSR 17.2.13 Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.
DSR 17.2.17 Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.
DSR 17.2.18 Supplying, installation, testing & commissioning of intelligentinterface unit B ACnet/ Modbus protocol i.e. supplying communication links between building management systemand fire alarm control panel complete as required.
DSR 17.2.19 Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.
DSR 17.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zonebutton paging station) with seamless integration facility withmain fire alarm panel for voice evacuation complete as required.
DSR 17.4.1 Supply, installation, testing and commissioning of 25 mm Outerdia CPVC PIPE with end caps including making air sampling opening of appropriate dia on appropriate interval and all accessories as required,(rate for area protected in sqm).
DSR 17.5.1 Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.
DSR 17.5.3 Supplying and drawing of cable Fire Retardant PVC insulatedcopper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required
DSR 17.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm
DSR 17.5.3.4 speaker cable Four pair, 2-core, 1.5 sqmm
NSI Supplying and installing 4 MP IP CCTV Bullet camera,CP Plus.
NSI Supplying and installing 4 MP IP CCTV Dome camera,CP Plus.
NSI POE Acess Switch 24 Port
NSI D-Link 6U Rack Enclosures Networking/Server Rack with cable management and Connectors etc. as reqd. D-LinkR (NWR-6U-5045-GR)
NSI 64 Input and 4 Output Channel Video Recorder For Cctv SystemSparshR (SR-NP3232F5H-H(E)(D)(P))
NSI Sony 82 cms LCD Panel monitor.
NSI FES 8 Ports Managed PoE+ Layer 2 Access Switch FESR (FES-GS-1010P)
NSI HT HDMI1.4 Cat.6 10.2 Hdmi Extender IHTR (IHT-HDMI-E60NTS (60Mtrs))
DSR 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
DSR 1.21.1 20 mm
DSR 1.21.2 25 mm
DSR 1.53.2 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run
NSI Supplyin & Installation of FES 8 Ports Managed Non POE Layer 2 Access Switch (DGS-1210-10/ME) with SFP++, along with 6 port Patch Panel LIU fully loaded including Patch chord, Connectors etc. etc. as reqd.
NSI Suppling Laying and fixing of 6 core OFC Cable as reqd.
KASANA BUILDERS PRIVATE LIMITED (BID ID -380498)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
BOQ.xls
BOQ • 0.99 MB
Tenderdocument.pdf
Tender Documents • 3.19 MB
Download all tender documents and submit your bid