12/EDC(K)/2025-26

Supply Item

CROSS ARM HOLDING CLAMP PCC POLE W/O N/B (As per Specification of RESPO & UPCL)

PG CLAMP 95-95 SQ.mm.

STAY CLAMP WITH N&B PCC POLE 8.5MTR (As per Specification of RESPO & UPCL)

EARTH WIRE CLAMP FOR PCC POLE WITH N/B (As per Specification of RESPO & UPCL)

EARTH WIRE CLAMP FOR SP-55 WITH N/B (As per Specification of RESPO & UPCL)

PP & CLAMP WITH N&B ST POLE SP-55 (As per Specification of RESPO & UPCL)

SUSPENSION CLAMP WITH EYE HOOK (As per Specification of RESPO & UPCL)

DOUBLE POLE CLAMPS WITH N/B FOR PCC POLE (As per Specification of RESPO & UPCL)

DOUBLE POLE CLAMPS WITH N/B FOR SP-55 (As per Specification of RESPO & UPCL)

MS CLAMP FOR DEAD END CLAMP WITH N&B (As per Specification of RESPO & UPCL)

MS CLAMP PCC WITH N/B FOR SUSP.CLAMP (As per Specification of RESPO & UPCL)

Dead End Clamp with I Hook (As per Specification of RESPO & UPCL)

STAY INSULATOR (As per Specification of RESPO & UPCL)

DANGER BOARD

IPC for 120sq. mm to 120 sq mm (As per Specification of RESPO & UPCL)

11 KV Fuse Set

MS Clamp with N&B for Suspension Clamp (As per Specification of RESPO & UPCL)

MS Clamp withN&B for PCC DeadEnd Clamp (As per Specification of RESPO & UPCL)

STAY CLAMP FOR SP-55 WITH NUT & BOLT (As per Specification of RESPO & UPCL)

LT Fuse Set With Fuse Wire

AL. CRIMPING TYPE LUGS 120 SQ.mm (As per Specification of RESPO & UPCL)

AL CRIMPING TYPE LUGS 400 SQ. mm (As per Specification of RESPO & UPCL)

DTR Installation Work

Chemical Earthing:Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode (to be supplied by contractor as per drawing No. A) as drawing B, connecting the same with G.I. Strip (to be supplied by contractor ) of size 35x6 mm as per drawing C for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Earthing of support with M.S. Earth rod of 2.5 meter long by hammaring of M.S. Rod to proper depth and connecting the earth electrode with the helpof G.I. wire as per construction manual.

Fabrication of M.S. Channel Angle iron after cutting in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESSPO sehedule and local approved drawing.

Excavation of earth for Stay pit of size 0.6x0.6x1.2mtr in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Fixing , tightening and nozzaling of LT Stay with pole and stay rod on required tension as per drawing / RESSPO manual.

Fixing , tightening and nozzaling of 11 KV Stay with pole and stay rod on required tension as per drawing / RESSPO manual.

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Erection of following Single PCC pole in proper level and alignment alongwith fixing of all accessories, like top channel & clamps as per RESSPO construction Manual.

Erection of following Single SP-55 pole in proper level and alignment alongwith fixing of all accessories, like top channel & clamps as per RESSPO construction Manual.

Erection of PCC Double support pole in proper level and alignment alongwith fixing of all accessories, like top channel, X-bracing & clamps as per RESSPO construction Manual.

Erection of SP-55 Double support pole in proper level and alignment alongwith fixing of all accessories, like top channel, X-bracing & clamps as per RESSPO construction Manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO construction Manual.

Muffing of poles size 0.45 cm x 0.60 cm radious with cc 1:3:6 (1 cement : 3 coarse sand : 6 graded stone 10mm nominal size) block size 45cm height from ground level including cost of cement, stone and sand etc.

Installation of new 250 KVA Tranformer on pole structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Installation of new 100 KVA Tranformer on pole structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Installation of new 63 KVA Tranformer on pole structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Mounting & Fixing of Fuse sets on double pole structures including making of connections complete work

Mounting & Fixing of LT Fuse sets on double pole structures including making of connections complete work

Laying, Spreading, Stringing and sagging of 11 KV / 33 KV line in Weasel Conductor complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Cartage of PCC Poles from store centre to construction site with loading, unloading at both points. (loading, unloading pluse carriage per pole) and proper stacking., 21-50 KM

Cartage of SP-55 Poles from store centre to construction site with loading, unloading at both points. (loading, unloading pluse carriage per pole) and proper stacking., 21-50 KM

Cartage of other material (other than poles) by vehicle fro Store Center to nearest construction site Store including loading and unloading at both ends.,21-50 KM

Cartage of the 63 KVA capacity transformers from store center to construction site with loading and unloading at both points. (Loading, unloading plus carriage of T/F), 21-50 KM

Cartage of the 100 KVA capacity transformers from store center to construction site with loading and unloading at both points. (Loading, unloading plus carriage of T/F), 21-50 KM

Cartage of the 250 KVA capacity transformers from store center to construction site with loading and unloading at both points. (Loading, unloading plus carriage of T/F), 21-50 KM

Head load cartage of PCC Poles from road to site (Rates are per pole / KM)(0-1 KM)

Head load cartage of SP-55 Poles from road to site (Rates are per pole / KM)(0-1 KM)

Head load cartage of Small material. Rates are per Km/Quintal including loading and Unloading.(0-1 KM)

Head load cartage of 63 KVA T/F. Rates are per Km/Quintal including loading and Unloading.(0-1 KM)

Head load cartage of 100 KVA T/F. Rates are per Km/Quintal including loading and Unloading.(0-1 KM)

Head load cartage of 250 KVA T/F. Rates are per Km/Quintal including loading and Unloading.(0-1 KM)

Laying of LT XLPE ABC 3X95+1X70 Sq.mm

Resagging of LT AB Cable

INST. OF DANGER BOARD/NUMBER PLATE

Laying & Fixing LT XLPE Cable

TNK Electricals (BID ID -389483)

SHUBHRA CONSTRUCTION (BID ID -389569)