PROVN OF HARD STANDING NEAR BLDG No. P-1452 WITH PROVN OF X-RAY BAGGAGE ROOM, INTERLOCKING TILES AND QTY-01 TOILET AT AF STN MANDORE UNDER GE(AF) NO.2 JODHPUR

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out as hard/dense soil all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out as soft/disintegrated rock all as specified and directed by Engineer-in-Charge.

Rough excavation not exceeding 1.5 m deep and getting out any type of soil all as specified and directed by Engineer-in-Charge.

Removing excavated material exc. 1.5 km but n exc. 5 m and depositing where directed complete all as specified by Engineer-in-Charge.

Forming embankments of soil including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base complete all as specified and directed by Engineer-in-Charge.

M & L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L Cement concrete type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass-concrete complete all as specified and directed by Engineer-in-Charge.

Formwork to flat Rough finished surfaces of concrete sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to better complete all as specified and directed by Engineer-in-Charge.

Formwork square, rectangular or polygonal to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engineer-in-Charge.

Formwork to flat Rough finished surfaces of concrete sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed by Engineer-in-Charge.

Formwork to flat Rough finished surfaces of concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge.

Formwork to flat Rough finished surfaces of concrete to chullah hoods, chajjas, troughs and similar items including edge complete all as specified and directed by Engineer-in-Charge.

S&F for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,Beams,footing, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

S&F for TMT steel bars 6-8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slab,hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

S&F for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concretecomplete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) for Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) for chajjas complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and directed by Engineer-in-Charge.

M&L ATT Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed by Engineer-in-Charge.

M&L ATT Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engineer-in-Charge.

M&L ATT Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engineer-in-Charge.

M&L ATT Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick cement concrete type D2, 1:4:8 (40mm stone aggregate) as in sub base complete all as specified and directed The rates of cement concrete in flooring include for: (i) Use and waste of form work/screed strips and to divide the area in panels. Where dividing strips are used, these shall be measured separately, without any price adjustment. (ii) Finishing surfaces of concrete topping even and fair (without using extra cement), and finishing surfaces of concrete in sub-floors, sub-bases, etc. even and rough to receive the topping layer. (iii) Finishing exposed edges fair or rounding or chamfering of exposed edges, where directed. (iv) Laying concrete in narrow widths, risers, treads, landings and the like.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (12.5mm stone aggregate) as in base complete all as specified and directed by Engineer-in-Charge.

M&L for Pre-cast cement concrete Type C1 1:3:6 (20 mm graded aggregate) set in CM 1:6 block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete Type C1 1:3:6 (20 mm graded aggregate) set in CM 1:6 solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls complete all as specified and directed by Engineer-in-Charge.

M&L for Providing, cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates,water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge. note- The rates include for use of formwork (straight or curved)

M&L for 10mm thick 1:6 cement plaster on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed by Engineer-in-Charge.

M&L for 5mm thick 1:3 cement plaster on ceiling finishing the surface fair and even and complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick 1:4 cement plaster on external surface finished even and smooth (without using extra cement) complete all as specified and directed by Engineer-in-Charge.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer or mortar 15mm CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic tiles,coloured,350x250x7mm/450x350x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on brick masonry surfaces all as specified and directed.(colour of tile required) complete all as specified and directed by Engineer-in-Charge.

M&L for 600mmx600mmx10 mm thick vetrified light/coloured shade ceramic tiles shade as approved flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:4 and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised frames powder coated (min thickness 50 microns) for doors, windows,partitioncomplete all as specified and directed by Engineer-in-Charge.

S & F Anodised aluminium window and ventilator shutters, side or top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 no.) suitable handle (1no.)complete all as specified and directed by Engineer-in-Charge.

S&F Sheet glass of 5.5 mm, ordinary quality and glazing with or without oil putty in square exc 0.5 sq. m in each pane fixed with beads and metalclips/pins complete all as specified and directed by Engineer-in-Charge.

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and including 20mm thick screed bed in CM 1:4complete all as specified and directed by Engineer-in-Charge.

Preparing of new surfaces, plastered or unplastered and applying three coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.

Preparing of new surfaces, plastered or unplastered and applying two coat of oil emulsion distemper on walls over one coat of alkali resist primer over a thin layer of putty complete all as specified and directed by Engineer-in-Charge.

Preparing of new surfaces, plastered or unplastered two coat of cement base paint over one coat of primer on external walls complete all as specified and directed by Engineer-in-Charge.

Supply and laying 25mm bore tubes, galvainzed steel, medium grade (ISI marked) with all fittings and fixed complete on walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and laying 20mm bore tubes, galvainzed steel, medium grade, (ISI marked) with all fittings and fixed complete on walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and laying 15mm bore tubes, galvainzed steel, medium grade, (ISI marked) with all fittings and fixed complete on walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20mm brass gate valve and 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore bib taps fancy type cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore pillar tap fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F 15 mm bore fancy fancy type, chromium plated type stop valve, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

S&F brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore brass chromium plated bib cock two in one with angle cock including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated health faucet of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed with 32mm dia pvc waste pipe fixed complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets including PVC flushing pipe, 32 mm dia and fixed complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel soap dish made of stainless steel 1.00mm thick, approximate 150x150 mm fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

S&F in grating doom 100 mm dia of PTMT (minimum weight 25 gms) complete all as specified and directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, fixing in opening as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F Pressed steel frames size 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type C-0, 1:3:6 (12.5mm stone aggregate) as in frames complete all as specified and directed by Engineer-in-Charge.

M&L for 35mm thick second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats but divide into square with with plain, chamfered or roun0ded, mitred and rebated sash bars, any numbers complete all as specified and directed by Engineer-in-Charge.

S&F second class HW rail and style Plain framed, 35mm thick panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-21 complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handles, cast type, anodized, of size 100mm complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 3mm thick glass pin headed type, ordinary quality and glazing with oil putty in square in exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

S&F Steel ventilators with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm dia sand cast pipe Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floor complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm dia sand cast pipe Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, fixed in walls complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm dia sand cast pipe Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, fixed in walls complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm dia bends with ducks foot or heel rest complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia bends with ducks foot or heel rest complete all as specified and directed by Engineer-in-Charge.

S&F 100mm dia cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches pipe complete all as specified and directed by Engineer-in-Charge.

S&F 75mm dia cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches pipe complete all as specified and directed by Engineer-in-Charge.

S&F for CI cowl 100mm dia fixed complete all as specified and directed by Engineer-in-Charge.

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed by Engineer-in-Charge. NOTE : Water proofing compound shall be measured and paid for separately as “Supply only”

M&L for preparation of new plastered surfaces and applying two coats of Polyurethene(PU) acrylic based water proofing liquid compound over one coat of diluted self priming with reinforcing fabric sheet as per manufacturer instruction to stop leakage/seepage from roof/wall complete all as specified and directed for work in building/structure of any height complete all as specified and directed by Engineer-in-Charge.

Preparation of newly surface any description, not otherwise, described, over 10cm width or girth and apply two coat of synthetic enamel paint on wooden surface over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of newly surface any description, not otherwise, described, over 10cm width or girth and apply two coat of synthetic enamel paint on steel surface over one coat of red oxidecomplete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound ISI marked.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out of hard/dense soil complete all as specified and directed by Engineer-in-Charge.

M & L Sand filling under floor or in foundation complete all as specified and directed by Engineer-in-Charge.

M & L 100 thick PCC type D- 2, 1:4:8 (40 mm graded aggregate)as in sub bases of floors and pavings complete all as specified and directed by Engineer-in-Charge.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over 25 mm thick sand cushion,pointed with grey cement and on pigments complete all as specified and directed by Engineer-in-Charge.

M & L 50mm thick PCC 1:2:4 type B- 2 ,20 mm graded stone aggregate as in floors and pavings finished even and smooth complete all as specified and directed by Engineer-in-Charge.

M & L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade "A"complete all as specified and directed by Engineer-in-Charge.

M & L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’complete all as specified and directed by Engineer-in-Charge.

M & L concrete bed to drain pipes of size 150 mm including packing under, and haunching against the sides of pipes after they are laid and tested in CM 1:3:6 type C2 complete all as specified and directed by Engineer-in-Charge.

S/F 25 mm bore tubes Medium grade (ISI marked) galvanised with all fittings as Tees, bends, etc laid in trenches complete all as specified and directed by Engineer-in-Charge.

S/F 25 mm dia gate valves gun metal with iron wheel high pressure screwed both ends for iron pipe or for union and fixed complete all as specified and directed by Engineer-in-Charge.

Cutting cast iron /GI pipes and reducing to required length for inseration of new branch tees valve complete all as specified and directed by Engineer-in-Charge.

Supplying, Laying, Jointing and testing of under ground cable XLPE insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 4 core 25 sqmm laid in trenches/ duct/ pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by Engineer-in-Charge.

M & L in GI tubing Light grade 50 mm incl all accessories for protection cable complete all as specified and directed in engr-in-charge

PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in foundation of poles etc filling and mess concrete complete all as specified.

Material and labour for point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLSH cable 1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia (external) but shall be increased as per actual site requirement in accordance with clause. (a) One light point controlled by one one way switch

Ditto as above item no.103 but for point wiring of (b) One celing fan/exhaust fan point controlled by one one way switch

Ditto as above item no.103 but for point wiring of (c) One socket out let 5 Amps on the same board

Ditto as above item no.103 but for point wiring of (d) One socket out 3 pin 5 Amps on the independent board.

All as per item No 103 above but with 2.5 Sq mm single core multi standard copper conductor cable for 6 pin 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge.

S&F switch flush type 5 Amp, 240 V single pole one way complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 2 in 1,6 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 3 pin 16 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose, 3 Terminal Point/PVC/polycarbonate, isolated body complete all as specified and directed by Engineer-in-Charge.

S&F lamp holder, PVC /Polycarbonate type with back plate suitable for batten fitting complete with necessary wire connection etc complete all as specified and directed by Engineer-in-Charge.

M&L for sheet metal enclosures distribution board where MCB to be used with 200 Amps rated bus bar CL-IP-43 240 V, 4 way Triple pole & neutral link complete all as specified and directed by Engineer-in-Charge.

S&F of MCB triple pole & neutral 63 Amps, 415 V complete all as specified and directed by Engineer-in-Charge.

M&L for sheet metal enclosures distribution board where MCB to be used with 200 Amps rated bus bar CL-IP-43 240 V, 8 way single pole & neutral link complete all as specified and directed by Engineer-in-Charge.

S&F of MCB single pole & neutral 32 Amps, 240 V complete all as specified and directed by Engineer-in-Charge.

S&F of MCB single pole 6 to 32 Amps, 240 V complete all as specified and directed by Engineer-in-Charge.

S&F in LED tube light along with fixture ,20 W ,220 V ,AC decorative type with box with effenicy 100 lumen/watt complete all as specified and directed by Engineer-in-Charge.

S&F in LED tube light along with fixture ,10 W ,220 V ,AC 2 feet completen with effenicy 100 lumen/watt complete all as specified and directed by Engineer-in-Charge.

S&F LED light fitting 10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans, complete with three blade, down rod, accessories 230V, 1400mm sweep, energy efficient 5 star rating with Squirrel cage induction motor complete all as specified and directed by Engineer-in-Charge.

Supply and fix exhaust fan steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed by Engineer-in-Charge.

S&F sub main wiring with 2 run of 6 Sq mm single core copper conductor cable drawn through in rigid PVC conduit ISI marked with fitting and 4.0 Sq mm single core copper conductor cable for continues earth wire complete all as specified and directed by Engineer-in-Charge.

Supply and fix electric water heater, storage type steel body with inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by Engineer-in-Charge.

M&L Cutting in position and providing Tee 25x15mm screwing the existing GI tubing for addn/altns of size 25 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F GI Tubes 15 mm dia, medium grade, galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply & fix Bib taps brass chormium plated with curtch or butterfly handle complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Valve stop screwed supplied and installed complete for size 15 mm dia. complete all as specified and directed by Engineer-in-Charge.

Supply & Fix PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm 6.0mm thick, buried directly in ground (earth pith not less than 2.25 mtr deep below ground level) with top edge of plated not less than 1.5 mtr below normal ground level connected toincl galvanized iron or steel earth lead wire 4.0mm dia by mean of bolts nuts check nuts & washers of galvanized iron or steel pipe 15mm dia medium grade and connected to main switch board watering pipe shall be 20mm dia GI medium grade incl excavation earth work in any type of soil pit RCC covercomplete all as specified and directed by Engineer-in-Charge.

S&F sheet matel enclosure SPN with a two pin and earth plug socket complete including 20 Amps MCB single pole netural 240 V AC complete all as specified and directed by Engineer-in-Charge.

S&F Socket outlet of 2 in 1, 3 pin, 6A complete all as specified and directed by Engineer-in-Charge.

Tirupati electricals works and services