Construction of Pre-fabricated entry point at Botapathree (Gulmarg Wildllife Sanctuary) under Capex Budget.

Amount

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and =disposal of surplus excavated earth as directed, within a lead of 50 metres:

Stone soling including levelling, watering, ramming and Consolidation etc,incl carriage,complete job

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Mud mat

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) All works upto plinth level

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. (steel bars already procured)

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded (steel already procured)

Providing and fixing of 0.50mm thick ribbed profile organic coated pre painted galvanic high tensile steel silicon pollester sheets i/c 60cm wide ridges and valleys wherever required incl. all fittings and fixtures.(Already Procured)

Providing and fixing of wall panel 40 mm thick (puff panel) and width 1 mtr or more insulated thick panel with 0.50mm PPGI sheet both sides with density of 40 kg/cbmtr, fixing on steel frame work with necessary flashings,screws, and all carriages of material upto site complete job (Already procured)

Providing and fixing of aluminium windows,doors ventilators made out of 50mmx45mm section of shutters incl. rubber gascuts, aluminium beeding fitted with 5mm glass and framework of aluminium 100x50mm section fitted with all required standard hardware.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (Already Procured)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing 32 mm dia. C.P. brass trap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 32 MM DIA

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete.

Providing and filling the joints with spun yarn cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I / C.I pipes

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete:

Providing and fixing plain bend of required degree: 100 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Sand cast iron S and S as per IS:3989

Providing and fixing pvc pipes class c 100 mm dia. Pipe

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in charge. PN-16 pipe , 25mm OD(SDR-7.4

providing and fixing of 50% of item above

providing and fixing bib tap CP brass Make : Hindware,cera or other relevant

Geysers 15 liter

Providing and fixing including all installations as per practice in electrical works Make : anchor, havells,goldmedal etc.the installation should comprise of fixing all the necessary conduits,wiring,switches,MCBs, panell board,lights,fans etc. Complete job Light points = 10 No.s

Fan points = 1 No.s

Heating point = 3 No.s

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm

Providing and fixing of kitchen countertop with granite shelf supported on 20 mm laminated glossy plyboard, with sink 450x450 size and one bib tap with all connection and fixtures. Complete job.

Stainless steel Sink 450x450

Carriage of different materials by mechanical transport incl head load for stacking at site

Sand 3km

cement 5km

Steel 5km (head load only)

Aggregate 8km

Waseem Ahmad Khan (BID ID -2233113)