SPECIAL REPAIR TO BLDG NO P 452 Comma T-93/7 AND T93 by 9 OF CWE HILLS DEHRADUN UNDER AGE BRIII OF GE CLEMENT TOWN DEHRADUN

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings etc n. exc 15cm thickness (below or above ground level) and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed by Engr-in-Charge.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thick ness including cover fillets complete all as specified and directed by Engr-in-Charge.

Dismantling timber scantling 40 Sqcm and over in section in any position complete all as specified and directed by Engr-in-Charge.

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified and directed by Engr-in-Charge.

Dismantling of Asbestos cement (corrugated, semi corrugated etc.) sheets as in roof coverings complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store andand removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed by Engr-in-Charge.

aking down shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/springclips and providing and fixing new one complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

M&L brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for half brick work with subclass ‘B’ bricks, straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ -150) as in roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE and finally complete all as Specified & directed by GE/Eng-in-Charge.Make - Tata Durashine , JSW steel India or equivalent in Roffit( Shiv Shakti Fibre Udyog)

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ- 150) as in ridges, hips, valleys/rain water / roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE and finally complete all as Specified & directed by GE/Eng-in-Charge.Make - Tata Durashine , JSW steel India or equivalent in Roffit( Shiv Shakti Fibre Udyog) )

S&F mild steel work as in trusses, rafters, purlins etc, and the like made out of MS pipe, flat, angle or hollow sections conforming to Fe-410-W (Gde-E-250) quality-A incl all necessary cleats, gusset plates etc complete all as specified and directed by Engr-in-Charge.

S&F mild steel framed work as in Staging for water tanks and the like incl caps , bases etc built up from two or more beam or cvhannel section or angles with plates incl lattice bars, stiffeners, gusset plates etc conforming to Fe-290, Gde-E-250 complete all as specified and directed by Engr-in-Charge.

S&F Welded steel wire fabric weight n.exc 4 kg/sqm fixed to wood or steel members complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L RCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

M&L for Vitrified any design and pattern coloured tiles scratch proof and stain resistance double charged (water absorption not more than 0.5%) 9-10mm thick (square/ rectangular) area of each tiles exc 0.42 Sqm but n.exc 1.00 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 complete. Tiles shall be comfirming to IS-15622.2017, Group B1 complete breaking strength 1300 N (Minimum) all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE. all as specified and directed

M&L for Vitrified any design and pattern coloured tiles scratch proof and stain resistance double charged (water absorption not more than 0.5%) 9-10mm thick (square/ rectangular) area of each tilesexc 0.42 Sqm but n.exc 1.00 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles complete. Tiles shall be comfirming to IS-15622.2017, Group B1 complete breaking strength 1300 N (Minimum) all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE. all as specified and directed.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge. (Make : Johnson Endura, Orient)

M&L for coloured Glazed ceramic tiles in vertical surfaces450 x300x 7 to 8 mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over 10mm thick rendering or bedding layer of cement mortar 1:4. Tiles shall be conforming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed Note : Shade of the tiles including colour, design and pattern shall be got approved by GE

M&L for Wall Cladding tile 7-8mm thick area of each tile exc 0.10 sqm but n.exc 0.20 Sqm of any colour and pattern set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering on wall in CM 1:4 and surface finished even & fair Complete all as specified and as directed by Engr-in-charge.

M&L for 16-18mm thick pre polished granite stone slab (apparant density not less then 2700 kg/cum of any colour) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:6) complete all as specified and directed by Engr-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F Factory made 100% Solid WPC Brown door Frame (100mm x 63mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 24mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 30mm thick Factory made Wiremesh SOLID PVC Door Shutter Consisting of frame made out of M.S.tube of 19 guage thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rail. M.S Frame shall have a coat of metal primer of approved make and manufacturer 19mm x 19mm M.S square tubes shall be covered with 5mm thick PVC heat moulded (100% LEAD FREE) plain sheet 'C' channel 75x30x60 out of 10mm shall be heat at 90 deg. towards inner site of both site of both face of the door forming stiles for top, bottom, lock rails shall be fitting of 10mm inner site all rails (T,B lock) shall be covered with 100mm wide PVC sheet S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be remove or fix again after changing of wire mesh when needed complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 18mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of singel side rigid laminate of approved colour adn other side plain white colour fixed with ss screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet shutters complete as per manufacturer's instructions complete all as specific and directed. Make Raj Shree Plastic wood/Sintex/Archid Plywood/ Kumar Arch Tech Ltd, Eco Cell.

S&F in repair 16 to 18 mm thick pre-laminated TESA ACTION shutter ultra violet (UV) coated panels of interior grade type -II with melamine finish of approved shade for kitchen cabinet / wardrobe/ wall paneling etc. fixing with necessary fitting (like keku fitting , spring clip, hanger plate moulder hinge/clip push Fix or stud fitting as per manufacturer’s instructions complete) all as specified and directed including taking down of old cupboard / cabinet shutters complete all as specified and directed by Engr-in-Charge. Make Raj Shree Plastic wood/Sintex/Archid Plywood/ Kumar Arch Tech Ltd, Eco Cell.

S&F set of 6 modular kitchen stainless steel basket, pull out drawers, shelves cabinet, rack basket tray for multipurpose utensils container shelf organizer complete including all fittings complete all as specified and directed by Engr-in-Charge. Make- Signora Kitchen baskets and accessories or Homecare Lifestyle or Vineet Enterprises as approved by GE.

S&F three track Pre coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32gauge wire mesh/gauze of 304grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 125mm centre to centre. Total Grill and wire mess unit shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions. )Make -Ashwani and sons, 1246/2 Meerut Road,Morta, Murad nagar-201003 ii)TATA Steel-Mumbai iii)Jindal,2-32,Gurgaon, Haryana-122001 iv) Ashish Industries, R-4/66, Raj Nagar, Ghaziabad , Ph-9891542779

S&F Pre coated Steel fixed type Window/ Ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The windows should be paneled with 5mm thick frosted glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Windows shall be provided with Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 125mm centre to centre. Total Grill shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions. Windows to be procured from any of the below mentioned companies- i)_Ashwani and sons, 1246/2 Meerut Road,Morta, Murad nagar-201003 ii)TATA Steel-Mumbai iii)Jindal,2-32,Gurgaon, Haryana-122001 iv) Ashish Industries, R-4/66, Raj Nagar, Ghaziabad , Ph-9891542779

S&F Aluminium powder coated three track sliding windows (with three sliding shutters, (One with and incl stainless steel wire mess and two with and incl 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per meter for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame 0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides 0.45 kg per metre including suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles etc complete all as specified and directed.

S&F of 100mm long stainless steel non megnetic butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

SS&F 150mm long, Stainless Steel non megnetic barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F 100mm size Stainless Steel handles non megnetic , all as directed complete all as specified and directed by Engr-in-Charge.

S&F 150mm size Stainless Steel handles non megnetic , all as directed complete all as specified and directed by Engr-in-Charge.

S&F of 250mm long (Length of bolt) Stainless Steel non megnetic sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed by Engr-in-Charge.

S&F in repair Hydrulic/Auto Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in positioncomplete all as specified and directed by Engr-in-Charge.

S&F in repair door closer aluminium ISI mark (extruded section) body hydraulically regulated, designation No. 3, universal type, complete all as specified and directed by Engr-in-Charge.

S&F in repair 300mm long MS Helical ordinary rat tail rod pattern door spring including roller and roller plate etc complete of approved quality complete all as specified and directed by Engr-in-Charge.

S&F in repair of 140mm Floor door stopper of aluminium alloy body (ISI Marked) and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge.

S&F in repair 4mm thick plain glass of aluminium window by taking down window shutter by any means and replacing rubber packing, jointing clip etc. complete all as specified and directed by Engr-in-Charge.

S&F in repair 5.5mm thick plain glass of aluminium window by taking down window shutter by any means and replacing rubber packing, jointing clip etc. complete all as specified and directed by Engr-in-Charge.

S&F Window blind is made up of several long horizontal or vertical slats of various types of hard material, including wood, plastic or metal which are held together by cords that run through the blind slats or roller window blinds made up of thermal fabric with roll up blinds mechanism, plain or printed type, of design and shade as approved by the Engineer-In-Charge complete with all connected fittings and fixtures incl taking down old drapery rods/ pelmets complete all as specified and directed and as approved by GE

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed

M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed (WPC shall be paid seperately)

M&L for 10 mm thick plaster on roof, chajja and roof parapet of CM (1:3) on RCC finished even and smooth without using extra cement etc ncl taking down cement plaster complete all as specified.

Supply only liquid water proofing compound(ISI Marked Only). complete all as specified and directed

M&L for two coats of oil bound distemper over a coat of 2mm thick wall putty to newly plastered surface including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old Aluminium joinery for repainting by hand sanded with sandpapers for applying two coats of Synthetic enamel paint sprayed onto the joinery over a coat of epoxy primer including packing existing glass panes, wiremesh and other fittings to protect so there is no chance of over spray complete all as specified and directed by Engr-in-Charge.

S& F for GI tubing 15mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

S& F for GI tubing 20 mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 15mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 20mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) (ISI Marked) junction single, (Single T) equal or unequal 110mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with access door (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore (ISI Marked) with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore (ISI Marked) with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC vent cowls 75mm (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia brass CP tubular towel rail D type 600mm long complete all as specified and directed by Engr-in-Charge. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No AKP-35711PS, Cera Cat Part No F-5006103, Hindware Cat Part No F-840013

S&F in repair bib tap cast cooper alloy with crutch or butter fly handle, 15mm bore screwed for iron pipe complete with wall flange complete all as specified and directed by Engr-in-Charge. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No FUS 29037, Parryware G-2304A1 and Cera F1014151.

S&F in repairs 15mm pillar taps cast coper screwed for iron pipe and fixed complete all as specified directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Cera cat part No QT F2006103, Hindware cat part No F-320001 , Jaquar Cat Part No FUS-29001

S&F Sinks ISI mark made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x160mm complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia brass CP Sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaquar Cat Part No CQT-CHR-23309B or equivalent quality in perryware or cera.

S&F 15mm Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-Charge. (Make : Jaquar/Kokler/Parryware) Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No ALD-573, Hindware 160027, Parryware-T-99408.

S&F in repair CP angular stop cock 15mm dia single way and fixed complete all as specified and directed by Engr-in-Charge. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No FUS-20953, Hindware Cat Part No F-320006, Perryware-G-4907A1.

S&F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No AKP-35751, Hindware Cat Part No F-880003, Parryware-T-6514A1.

S&F in repair Sheet glass shelf assembly/Glass Corner assembly set of three consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No ACN-1171N, Cera Cat Part No-F-5005301, Parryware-T-6009A-1.

S&F in repair vitreous china WHB size 505x410x185mm with full pedastal, white with flat back including CP waste coupling and all as specified and directed by Engr-in-Charge. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No AIS-WHT-101801, Hindware Cat Part No -11032

S&F in repair Vitreous china white wash down couple closet composite type including PVC soft seat cover white complete all as specified and directed by Engr-in-Charge. Make : Jaquar Cat Part No LYS-WHT-38853S, Hindware Italian Cat Part No 92509 (S-30) Cera Cat Part No S1013132 S.

S&F in repair Vitreous China white half stall urinal of size 330x345x 610mm top inlet fix with necessary brackets including 32mm dia CP waste coupling, suitable brass chromium plated urinal spreader, waste pipe etc complete all as specified and directed. Make :- Jaquar Cat Part URS-WHT 13261 or equivalent quality in parryware or cerra.

S&F bottle trap (with internal partition) 32mm dia size with 250mm and 190mm long wall connection & wall flange complete all as specified and directed by Engr-in-Charge Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site..

S & F in repairs Stainless steel kitchen plate rack 0.80mm thick sheet of over all size 31" x 30" x 10" fixed with steel screws and steel rawal plugs complete all as specified and directed. Make:– Prayag Cat Part No- P 346 , Blue star silver shine Cat No-SSKPR-314) or equivalent of other make as approved by AGE/AGE (I). Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repairs PVC water storage tank double layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed by Engr-in-Charge.

S&F false ceiling with Semi perforated 12mm thick Square edged GRG False Ceiling tiles at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 x 595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Nomocombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120grams per Sqm incliuding both sides) comprising of main-T runners of size 15x32mm of length 3000mm, cross-T of size 15x32mm of length 1200mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per Sqm) i.e. 50mm lon, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod up to 1000mm length and L-shape level adjuster os size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engr-in-Charge. Make : Diamond Ceiling, Gypcore, Maruti, Gypsum, Shera

M&L for joint free Non-skid ceramic coloured tiles of any deisgn and pattern 7-8mm thick (square/rectangular), area of each tile exc 0.06 sqm but not exc 0.11 Sqm in floor etc, including 15mm thick screed bed in CM (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles. Tiles shall be comfirming to IS-15622.2006. Group B II Grade-IV Complete all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE.

S&F 6mm thick PVC heavy grade hollow profile designer sheet strips & channel feathered at edges of approved quality and design PVC Wall/Ceiling lining fixing with frame including all beading, matching PVC angles at all window corners with all necessary frame as required complete all as specified and directed by Engr-in-Charge. Make Raj Shree Plastic wood/Sintex/Archid Plywood/ Kumar Arch Tech Ltd, Eco Cell.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed as site by Engr-in-Charge. Note :- (i) The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of emulsion paint. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii) The colour/shade will be all as approved by GE. (iii) The cost of scaffolding wherever required are deemed to be included in the rates quoted by the contractor. (iv) After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building.

M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching poweder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of perfomance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engr-in-Charge. Note :- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted. (ii) After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (iii) The colour/shade will be all as approved by GE.

S & F in repair salid aluminium composite panel 4mm thick of any colour fixed with screws to steel frame work complete all as specified. Note :- The colour/shade will be all as approved by GE.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete , including fixture and fittings such as switches, ceiling roses pendents, rigulators, sockets, light fittings etc. removing materials to store for keeping in safe custoy or for taking credit and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed.Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten / PVC Conduit etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified & as directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified & as directed.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 107 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

All as per item No 107above but with 4.0 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. Make Legrand Cat No- 673401, Indo Asian Cat No-800000, Cona cat No-9251

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. Make Legrand Cat No- 673411, Indo Asian Cat No-800002, Cona cat No-9386

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge. Make Legrand Cat No- 673452, Indo Asian Cat No-800020, Cona cat No-9316

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge. Make Legrand Cat No- 673455, Indo Asian Cat No-800022, Cona cat No-9416

Supply and fixing step socket type modular fan regulator 120/280 V , 100Watt all as specified and as directed. Make Legrand Cat No- 673430, Indo Asian Cat No-800043, Cona cat No-9381

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI Marked, complete all as specified & as directed.

Supply and fixing batton/angle holder insulated body with back ISI Marked plate suitable for batten fittings complete all as specified & as directed.

Supply and fixing in repair energy efficient LED lights fitting, 9 watt , 230 Volt, of 600 mm length,CCT 6000ºK to 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000 to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion < 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed. Make Shakti/ Havells/Crompton.

Supply and fixing in repair LED lights fitting 1X18 watt ,4 ft with extruded aluminium housing heat sink, environmental friendly energy efficient translucent diffuser with LED light source,2400 Lumens( minimum) coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessories including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified & directed cat No. Make Shakti/Havells/Crompton

S& F in repair oval shape Bulk head Edge-lit LED fitting, 09 watt comprising with high brightness LED, IP-65 protection, system efficacy not less than 120 lumens /watt, CCT 6000ºK to 6500°K , surge protection range 4 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion < 20%, colour rendering index> 80, 02 year warranty fixed on site with all accessories including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified & as directed. Make- Shakti/ Havells/Crompton.

S& F Glaze Wall Light including 9/10 watt LED lamp ( B22), 6500 K of make Havells / Shakti/ Crompton all as specified and as directed

Supply and fixing LED building security light 1X20 W housing made out of pressure die-cast aluminium alloy with toughened glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection up to 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 130 Lumens/watt, power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on wall with 02 Nos MS clamp made out of 40X6 mm FI and bracket made out of 32 mm dia light grade GI pipe not less than 0.90 mtr long bend to shape complete all as Specified and directed including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from terminal box to light fittings complete all as specified and as directed by Engr-in-Charge (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRSno Make Shakti/Havells/Crompton.

Supply and fixing LED luminaire 600mm X 600mm, 35/36 watt, 220V AC recessed type, 3000K with high efficiency PMMA diffuser soft glair free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.Make in Shakti/ Havells/ Crompton Greaves

Supply and fixing sheet metal enclosure double door type MCB DB VTPN 4 Way with 160 Amps , 25KA, 4 Pole MCCB of Make legrand, Schnider, Siemens, L&T,ABB all as specified and as directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar all as specified and directed .Make legrand, Schnider, Siemens, L&T,ABB

Supply and fixing MCB SP 5 to 30 Amp 'B' series 10 KA repturing capacity complete all as specified. Make legrand, Schnider, Siemens, L&T,ABB

Supply and fixing MCB SPN 40 Amp 240 V AC 10 KA repturing capacity all as specified. Make legrand, Schnider, Siemens, L&T,ABB

Supply and fixing single pole and neutral enclosure with a two pin and earth plug & socket complete with 01 No, RCCB 25 Amp, 30 mili amps, DP 240 Volts AC Complete all as specified. Make legrand, Schnider , ABB ( Note- Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick/ concrete surface and making good disturbed surface shall be deemed to be included in quoted rates )

M&L for sub main wiring but using two single core multistranded PVC insulated copper conductor of size 4 sqmm 1100 volt grade drown into PVC Rigid conduit of suitable 20/25 mm dia, ISI marked including 4.0 Sqmm. PVC multi standard cable in green colour for continieous earthing and making good the disturbed surfaces of wall /floor/ ceiling to match with existing surfaces.all as specified and directed.Make for Conduit : AKG / PRESTOPLAST / PRECISION ) Note : Three runs of 4 Sqmm PVC cable and one run of PVC conduit shall be measured as one length.

S&F sub main wiring with two single core PVC insulated,unsheathed, stranded copper conductor cable( FRLS) 6 Sqmm with 6 Sqmm PVC insulated, unsheathed, stranded copper conductor cable as earth wire in and including rigid PVC conduit 25mm dia or higher, medium grade ISI marked and earth wire connected to common earth dollycomplete all as specified and directed. . Make of Cable : Finolex/RR Cable/Havells & Make for Conduit : AKG / PRESTOPLAST / PRECISION ) Note: Three run of 6 sqmm cable and one run of PVC conduit shall be measured as one unit

Taking down old u/s cable & Supply and laying or fixing on wall with clamping or passing through pipe, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade , cross - sectional area of 25 sqmm 4 core complete all as specified & as directed.

Supply & Fixing exhaust fan, 240 volts, AC, 50 Hz , single phase, of size 300mm sweep metallic body ( RPM will not be more than 900 )with blades, and frame and louvers complete all as specified & as directed. Make: Bajaj/ Havells / Jaquar & Co. Pvt Ltd.

Supply & Fixing Fresh Air fan, made of sturdy Engieering plastic complete with louvers shutter, AC single phase, 230 volt , 50Hz RPM 1200, Copper winding of sweep 300mm and minimum airflow rate shall be 520 CMH or more complete all as specified and as directed.Make: Bajaj/ Havells / Jaquar & Co. Pvt Ltd.

M&L for PVC rigid concealed conduit medium grade for computer net working and communication system of size 20 mm bore all as directed.Make for Conduit : AKG / PRESTOPLAST / PRECISION )

M&L for Telephone socket RJ-11 with metal flush box and cover plate complete all as specified and as directed..

M&L for TVsocket with metal flush box ith metal flush box and cover plate complete all as specified and as directed..

M&L for providing,drawing,connecting and testing of telephone wire 20 pair,0.5 mm dia tinned annealed high conductivity copper conductor with high density polythene insulation,paired,polyster tapped and FR PVC sheathed complete all as specified and as directed..

S&F co-axial cable RG-11 complete all as specified and as directed.

Taking down ceiling fan from existing location & refixing the same ceiling fan after servicing & greasing connecting up including provision of cable flexible 3 core of suitable size wire from ceiling rose to fan connector.complete all as specified and as directed..

Taking down Decorative glass jhummar from existing building and again refixing the same after cleaning & washing properly & connecting up including provision of cable flexible 3 core of suitable size wire complete all as specified and as directed..

S&F Led light fittings 20 watt with extruded aluminium powder caoted, IP 66 linear wall washer to accentuate artwork on entrace and walls complete all as specified and as directed.. Make in Crompton/Havells/ Shakti

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.Crompton/Havells/Shakti

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

KAPOOR ELECTRICALS

ANKIT KUMAR

RAM PRAKASH AND ASSOCIATES