Special repair to toilet block of Bldg No 334, 335 and 336 OR Single living of 66 MD Regt in Army area Jodhpur

Amount

Demolition of cement concrete in ground floors and pavings n. exe 15 cm thickness (below or above ground level) complete all as specified & as directed.

M&L 50 mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, without using extra cement complete all as specified and directed.

M&L PCC solid building blocks 10 Cm thick type B1 1:2:4 using 20 mm graded stone aggregate set in cement mortar (1:6) all as specified and directed.

Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & as directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed.

All as per item No 5 above but except stone complate all as specified and directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floor and levelling course complete all as specified and directed.

M&L for 40mm thick plain cement concrete (1:2:4) type B1, (using 20mm graded stone aggregate) as in floor including finishing cement concrete surface even and smooth without using extra cement complete all as specified & as directed.

S&F machine made precast cement concrete blocks (interlocking paves) of 60mm thick with 6mm top layers of ante abrasive material laid over and including 25mm thick sand cushion . The interlocking joints shall be filled with fine sand. The compressive strength of block shall not be less than 350 Kg/Cm2 complete all as specified and directed.

S&F machine made precast cement concrete curb stone blocks using Cement concrete 1:3:6 type C2 (20mm graded stone agg) all as directed by Engr-in-Charge.

M & L broken stone hard core of gauge n. exc. 63 mm deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rolled / rammed to a true surfaces complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the out of MOD land complete all as specified and directed.

M/L for 20mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded crushed stone aggregate) use as a levelling course complete all as specified and as directed.

M&L for 15mm thick screed bed or bedding layer in CM 1:4 floor finished even & rough to recievr tiling/floor finish complete all as specified and directed.

M&L non skid ceramic colour joint free tiles 6 to 7 mm thick of size area exc 0.11Sqm but nexc 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed .

M&L for glazed colour ceramic tiles of size 250x350x7mm/300x450x7mm, thick laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles complete all as specied and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Rendering 10 mm thick in CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified & directed.

M&L for 10mm thick rendering in CM 1:4 over stone masonary surfaces incl finishing the surface fair & rough to receive tiling etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar all as specified

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

M & L three coats of white wash on newly plastered surface of wall including preparation of serfaces complete all as specified and directed..

M & L three coats of white wash on newly plastered surface of ceiling including preparation of serfaces complete all as specified and directed.

M & L two coats of cement based paint on newly plastered/ unplastered surface of wall including preparation and one coat of chalk white of serfaces complete all as specified and directed.

M/L one coat of cement base paint on old surfaces including preparation complete all as specified & directed.

M & L one coats of white wash on old surface of wall complete all as specified and directed..

M & L one coats of white wash on old surface of ceiling complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Dismantling of stone slabs of any description or any thickness in floors, roof etc laid bedded and dry complete all as specified and directed.

M&L for 5 cm thick sand stone slabs as in chajjas n.exc 2m in length punched dressed on face and along exposed edges ,self faced on other side and set and pointed in CM 1:4 all as specified and directed.

M & L 18 to 20 mm thick granite(approved quality by user ) in WHB counter top, cooking plateform and similar places etc laid in dry bedded in pinning to wall including cutting rubbing grinding and polishing to edges and rounding off granite polish slab for smooth finish complete.

M & L 18 to 20 mm thick machine cut Kota stone slab flooring over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing icluding 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for 18- 20 mm thick Kota stone slabs as in skirting , risers of steps & other vertical surfaces etc including 10mm thick rendering in CM 1:4 as backing coat complete all as specified and directed.

Taking down chowkhats or frames area not exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhats or frame area exc 1.5 Sqm but not exceeding 4 Sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down PVC shutter of any description, area exc. 1 Sqm but n exc 2 Sqm and re-fixing in the same opening after necessary repair like hinges etc. complete all as specified and directed.

S&F mild steel work as in doors frames using MS angle iron complete all as directed.

S/F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick pvc sheet reinforced with MS square tube all as specified.

Taking down steel window/ventilator complete all as specified and directed.

Supply and fabrication of Mild steel guard bars and welded to window frames complete all as specified.

Factory made box type steel ventilator with glazing bars dovetailed or welded with one shop coat of zinc chromate primer all as specified.

Factory made box type steel ventilator without glazing bars dovetailed or welded with one shop coat of zinc chromate primer all as specified.

Hackilng out old broken glass (any thikness, size quality or description) from metel frame including punching or drilling cut old glazing pins & providing fixing new ones.

S/F of 4 mm thick pinheaded sheet glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm complete all as specified and directed.

S/F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long complete all as specified and directed.

S& F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S & F butt hinges 100 mm long,extruded aluminium alloy with mild steel hinge pin anodised type C- 21 for PVC door complete all as specified and directed.

M/L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing including necessary form work all as specified.

S&F flat iron for hold fast and similar work confirming to Fe-290 Gde-E-165 fixed with welding and necessary item complete all as specified and directed.

S & F for mild steel work in tubuler posts , rafter, purline etc. including special shaped washer etc. complete using ERW or including butt welded tubes conforming to IS-1161-1976 grade st -240 complete all as specified and directed.

Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

S&F for wind ties for roof incl securing bolts etc complete

S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, flush pipe of 32mm dia HDPE pipe etc all as specified & directed.

S & F as in repairs vitreous china wash down water closet Anglo Indian Type pedestal pattern with seat cover and jet spray complete incl fixing of flush pipe etc complete all as specified and directed.

S & F in repair Vitrous china wash basin as in repairs, white flat back size 550x400 mm including , waste pipe, MS brackets complete all as specified and directed.

S & F vitreous china urinal full stall type colured bowl type (back or corner wall type) complete including providing and fixing plugs, waste pipe 32 mm dia , urinal spreader 15 mm dia ete in cement mortar 1:2 and fixing with and including brass screws 60 mm in length, complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms)

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed.

S&F in repair PTMT towel rail 450 mm long fiexd to wall with chromium plated brass screws and woodn cleats Min weight 170gms approved make complete all as spcified and directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S/F in repair of chromium plated shower rose 75mm dia round shape complete all as specified and directed.

S & F in repair 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S &F in repair 20 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

S & F as in repairs 15 mm dia angular stop cock with chromium plated long thread with flange complete.

S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated with (concealed type) all as specified .

S&F in repair of bib, cock 15mm dia, cast copper alloy with crutch or butterfly handle, screwed for iron pipe all as spcified as fixed .

Supply & Fixing in repair low level flusing cistern PVC 10 ltrs capacity with float valves (ISI Marked) white with inlet ball valve including float and includign pvc connection complete all as specified and directed.

Taking down PVC low level flusing cistern from the wall and fixed the same after replace the flush bend, internal kit, washer etc complete all as specified and directed.

M&L in repair for high quality looking mirror with fancy type beading fixed to wall with chromium plated screw area n exc 2.0 sqm complete all as specified and as directed

S/F in repair 15 mm bore CP brass two way angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle scrwed both ends for iorn pipe fixed in repair complete all as specified and directed.

S & F in repair Bidet spray (Health faucet) with 1 meter PVC tube and holder, complete all as specified and directed. Make Jaquar

S&F PVC connections 15mm dia with PTMT nuts of length 450mm all as specified and directed.

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore as directed

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore as directed

S&F 110 mm dia PVC SWR pipes single socketd in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm dia PVC SWR pipes single socketd in any length with rubber rings joints laid fixed to wall complete all as specified and directed.

S&F 75 mm dia PVC SWR pipes single socketd in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F 75 mm dia PVC SWR pipes single socketd in any length with rubber rings joints fixed to wall complete all as specified and directed.

S&F110 mm dia PVC (SWR) branch pieces single socketed T equal or unequal complete all as specieied and directed.

S&F 75 mm PVC (SWR) branch pieces single socketed T equal or unequal complete all as specieied and directed.

S&F110 mm dia PVC (SWR) bends any radius complete all as specified and directed

S&F 75 mm dia PVC (SWR) dia bends with oval acess door fixed to pipe complete all as specified and directed.

S&F 110 mm dia PVC SWR vent cowl fixed to pipe complete all as specified and directed.

S&F 75 mm dia PVC SWR vent cowl fixed to pipe complete all as specified and directed.

S&F of PVC SWR floor trap plain grating including jointing with solvent cement 100/75mm dia complete all as specified and directed

S&F in repair of PVC SWR gully trap 125/110 mm size including setting and jointing with solvent all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds mitered or stopped ends etc. complete all as specified and directed.

M & L PCC 1:3:6 type C-I using 20 mm graded stone aggregate as in surface channel, drain etc. including necessary use and waste of form work complet all as specified and directed.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring benching to drain, coping, etc and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and as directed.

Disconnecting of old serviceable PVC tank setting aside (or lowering if required) including repair cleaning etc and hoisted in same location including reconnection and refixing for proper functioning of over head tank complete all as directed.

S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009, complete.

S & F in repair 1000 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009, complete.

S & F 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S & F in repair 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

M&L 50 mm thick PCC (1:2:4)Type B-1 using 20 mm graded stone aggregate for water tank plinth all as specified and directed.

Excavation in trenches for fdn n.exc 1.5m wide and n.exc 1.5m in depth & getting out in soft /loose soil

Returning filling in including spreading ,levelling,watering and well ramming in layers not exc 25cm

Removing excavated at a level n.exc 1.5 m above the starting point

M&L for 15mm thick rendering in cement mortar 1:3 using WPC @ 3% by weight of cement or as per manufacturers instruction complete all as specified and as directed. ( Note : WPC shall be measured and paid seperately)

Supply only water proofing compound (ISI Marked).

M&L for 75mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregates to use in subbase of floors of sunken portion laid in slope 1:40 to the surface of RCC slab shall be made even and smooth without using extra cement when concrete is still green complete all as directed by the Engr- in -charge.

M&L for applying one coat of cold emulsion bitumenous primer @ .25kg/sqm shall applied on plastered surface including side walls. There after a layer of APP membrane 1.5mm thick as specified above shall be laid by torch application method as per manufacturer instructions

M&L for PCC (1:5:10) lean cement concrete type E2 using 40mm graded stone aggregates in mass concrete after carrying out satisfactorly testing of CI pipes/PVC pipes joints and slab walls by filling water for 72 hrs ,sunken portion of nahani trap/floor trap and pipe joints shall be embeded in PCC 1:3:6 type C1 using 20mm graded stone aggregate complete all as specified and directed..

S&F 32 mm dia bore light grade galvenised steel water tubing provided 30cm beyond wall surface to drain out leakage if any. The mouth of GI pipe shall have Gravel to avoided chocking. The top of sunken portion of RCC slab to be finished such that its slope towards spout.

Demolition and breaking up RCC/Salt glazed stoneware drain pipe set & jointed in cement mortar laid in trenches 150mm bore of pipe.

Demolition and breaking up RCC/Salt glazed stoneware drain pipe set & jointed in cement mortar laid in trenches 200mm bore of pipe.

Material an labour for RCC pipe 150mm bore laid in trenches over existing bed and jointed complete with coller fixed and jointed in cement mortar and tested completed all as directed.

Material an labour for RCC pipe 200mm bore laid in trenches over existing bed and jointed complete with coller fixed and jointed in cement mortar and tested completed all as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required

M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150/200 mm dia pipe complete all as specified and directed.

Supply , laying jointing and testing 150/200 mm bore reinforced conctete pipes class NP-2 laId and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement concrete complete all as specified and directed. (Note- cement concrete used for haunching concrete shall be measured and paid separatly)

Demiolition of reinforced cement concrete of as staircase, landing, chajjas, cover slab and similar suspended work of any description and any position not otherwise

Providing precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab for man hloes set in CM 1:6 complete all as specified and drected.

M&L for TMT bars 6 to 8mm dia and over, cut to length , bent to shape required including cranking, bending & binding with MS wire (annealed ) not less than 0.9mm dia or securing with clips, as in stirrups also & all as specified.

Material and labour for plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone agg as in coping of manhole including necessary form work complete all as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on stone masonry surface of walls mixed with WPC, as per manufacturer’s direction and finished the surface even and smooth without using extra cement.

Cleaning of septic tanks of any capacity & any size by taking out sludge (working condition is in foul condition) & removing the sludge to outside defence land in closed vehicle all as directed by Engr-in-Charge.

Taking down existing old Tar-felt from RCC roof, stone roof in any thicnes etc carefully including cleaning the roof surface by wire/coir brush and remouving all grits, stones, fungus , moss and finally washing down with water to the entire satisfaction of Engr-in-Charge .

M&L for PCC 1 : 2 : 4 type B0 using 12.5 mm graded stone aggregate to makeup undulations as in levelling course over roof surface

M& L for roof treatment in the following stages :- (a) first Course : M&L for 10 mm thick plaster with CM 1:3 mixed with water proofing compound as per manufacturee instructions (Note: - WPC shall be measured and paid separately) (b) Second Course : One coat of bitumen primer T-10/polymerised confirming to IS 3384 @ 0.30 ltr/Sqm (c) Third Course : One coat of Bininding material using blown type bitumen conforming to IS 702 grade 85/25 @ 1.20 Kg/Sqm (d) Fourth Course : A layer of APP membrane polymeric membrane centre core of 100 micron HMHDPE outer film 20 micron each, thickness 2 mm having weigh 2.25Kg/Sqm (e) Fifth Course : A coat of bonding materail using blown type bitumn conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm (f) Sixth Course :40mm thick PCC 1:2:4 padding, well compacted using 20 mm graded aggreegatel with groovs shall not be exceeding 0.40 Sqm

Taking down carefully cement concrete/spalled out concrete from RCC roof projections, ceiling, sunshades, beams etc upto cover depth by chipping out lightly including necessary scaffolding etc complete.

M&L for fixing 12 mm dia TMT bars way of stiching (welding or tieing with existing reinforcement) incl drilling holes etc and securig ends in walls etc complete all as specified and directed.

M&L for cleaning the existing reinforcement of slabs, chajjas etc and applying a coat of SIKA RUSTOFF 11 to remove the loose rust particle etc and thrughly cleaning the surface complete all as specified and directed.

M&L for applying a coat of bond made with cement slurry (1 part of cement to 1.5-2 parts water) mixed with admixture latex power mixed @ 5 Kg per 50 Kg of cement and applying to the concrete surface @ 200gm/Sqm to obtain tack complete.

M&L for for 15-20 mm thick rendering in CM 1:2 using 1 part cement and 1 part 2-3 mm screenings of stone aggregate and 2 part coarse sand of over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm/50 Kg of cement and finishing the surface even and rough to receive final rendering coat complete.

M&L for for 10-15 mm thick rendering in CM 1:3 over the bond coat applied surface with SIKA PLASTOCRETE SUPER admixture @ 100 gm/50 Kg of cement and finishing the surface even and smooth complete all as specified and directed.

Taking down or up steel tubing and connection including cleaning for refixing or removal to store. 25 mm dia

All as per item No 134 above but 20 mm dia

All as per item No 134 above but 15 mm dia

S & F GI water tubing, medium grade, galvanized, with all fittings fixed to wall, ceiling or laid in floor all as specified. 25 mm dia,

All as per item No 137 above but 20 mm dia

All as per item No 137 above but 15 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete

Point wiring complete with 1.5 sqmm, single core, multi stranded, copper conductor, PVC (FR), insulated, unsheathed cable, confirming to IS-694, 1100 volts grade, ISI marked (class V conductor), in and including PVC concealed conduit (MMS), ISI marked not less than 20mm, with accessories fixed on surface of wall/roof/ceiling etc and including sunken pressed steel terminal boxes in wall but including 3mm thick plastic laminated sheet top cover (ISI marked hylem sheet Make Anchor and 1.50 sqmm PVC insulated unsheathed stranded copper conductor for common earth and connecting to earth dolly material and labour for :- One light point controlled by one, one way switch

All as per item No 141 above but One fan /Exhaust fan, point controlled by one way switch.

All as per item No 141 above but One socket outlet 3 pin 6 Amps on same board

All as per item No 141 above but One socket outlet 3 pin 6 Amp on independent board

All as per item No 141 above but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board .

S&F switch flush type single pole one way 6 Amp ISI Marked

S&F switch flush type single pole one way 16 Amp ISI Marked.

S&F socket out let , 5 pin , 6 Amp FT.

S&F socket out let , 3 pin ,16 Amp FT. ISI Marked

supply and fix socketed stepped type electonic fan regulator flush type , ISI Marked.

S & F Ceiling rose, 3 terminal/PVC/ polycarbonate, isolated body

Fixing only LED tube light fitting three colour, 20/22 watt,4000 lumens, complete with all accessories etc internally pre-wired , including LED lamp-1No made of connectiong up with , multistranded copper conductor of size 1.00 sq mm flexible cable complete all as specified. Note:- LED tube light fitting 20/22 watt complete shall be issued under sch 'B' free for fixing.

S&F insulated Batton lamp holder metal cased body of brass with back plate suitable for batton fittings including 7/9 watt LED Lamps. Note:- LED Blub 7/9 watt shall be issued under sch 'B' free for fixing

M/L in repairs sub main wiring with 6.00 Sq mm single core multistrandred copper conductor PVC insulated and unsheathed cable passing through PVC concealed conduit and making good the distrurbed surface of wall inc 6 Sq mm single core copper conductor cable PVC insulated and unsheathed cable as earth wire. Note :- Two runs of cable 6 Sqmm and One run of 6 Sqmm shall be measured as unit length.

S&F sheet metal distribution board with 200 Amps rated copper bus bar Confirming to relevant IS,.SPN 4way, Make;-Legrand/ABB/Havell's Note -Rate are deemed to be included for flashing in wall concealed complete, making good and matching existing surface.

S&F MCB Single pole 5 to 30 Amp, 10 kA, ISI Marked.

S&F MCB SPN 63 Amp, 10 kA, ISI Marked.

Fixing only connecting, and commissioning of street light fitting 25 watt LED , IP-65 protection, single peice pressure dia cast aluminium alloy housing high grade powder coated finish with heat resistant toughned clear glass cover for lamp and contror gear compartment with high voltage surge protection device, Prewired including GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable complete all as specified . Note:- LED street light fitting 25 watt complete shall be issued under sch 'B' free for fixing.

M/S KAUTILYA GARG

Diva Infra

Nikhat nirman

Jai Doulat Construction Co

KARNI CONSTRUCTION COMPANY

SURESH TRADERS