Constructing New Feeder using UG Cable from Neyyattinkara Substation to Keeliyodu - Part 1 under Electrical Section, Neyyattinkara of Electrical Division, Neyyattinkara under Electrical circle Kattakada.

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 numbers of poles excluding loading& unloading charges.

Transporting Transformers by hired vehicle to a distance upto 5km and carrying upto 2 numbers of 63/100/160/250kVA Transformers / Ring Main Units excluding loading& unloading charges.

Transporting Transformers by hired vehicle to a distance beyond 5km and carrying upto 2 numbers of 63/100/160/250kVA Transformers / Ring Main Units (Running km).

Doing horizontal directional drilling along/across roads, mtr supplying and pulling 125mm dia HDPE pipe and drawing 11KV 3 X 300 sq.mm, Aluminium XLPE UG Cable through the HDPE pipe, including surveying the site for collecting information about underground utility installations and other obstructions using suitable modern sensing eqipment, restoring the damages occured if any, pit marking, pilot drilling, pre ramming, closing of pits with normal soil/filled sand/crusher sand and consolidation to the satisfaction of the road owner and traffic police as they insist, taking cable to the open trenches, RMUs, transformer yards etc mounting the cable after providing loop at 1.2m depth, pulling HDPE (PE 80, PN6 kgf/cm2) at rising point(0.5m below ground level and 1.5m above ground level), testing, commissioning, placing route markers at 100m interval, writing identification name, date of laying, date of commissioning etc legibly at the cable raising point using polyurethane paint etc as per the direction of department officers including cost & transportation of HDPE pipe and coupler and excluding and conveyance of cable

Cost of construction of foundation, base plates, fixing anchor bots, loading & unloading, handling, erection, allignment and allied works for the installation of Data Aquisition compatible Extensible type Ring Main Units with terminal protector boots & extension modules, actuators for remote operatios, communicable FPIs, CTs, PTs & relay contacts for SCADA, giving power & control wiring and connections, providing terminal protector, interconnecting RMU bus bar and control cables, providing metered LT supply from nearest LT pole, providing earth leads, cable mounting & terminations, giving connections after ascertaing proper phase sequence, providing location name & warning boards, burying cables & refilling, conducting all precommissioning tests as required, complete, except cost of conveyance. RMUs with two nos load break switches & one VCB

Supplying and Providing Canopy for 11KV Ring Main Unit, made out of CRCA sheet steel 2mm thickness ,having a total width of 1.6 metre (approx) in required length with minimum 20 Deg C slope extension 30cm out side of panel in all sides, providing necessary steel supports, painted with marine epoxy paint 2 coats or more over a coat of epoxy primer including transportation, fixing the canopy roof as a single unit rain guard on the existing RMU , covering RMU,Add-on, bus duct, cable entry box etc.suitable as per site requirement

Cost of construction of foundation, base plates, fixing anchor bots, loading & unloading, handling, erection, allignment and allied works for the installation of Data Aquisition compatible Extensible type Ring Main Units with terminal protector boots & extension modules, actuators for remote operatios, communicable FPIs, CTs, PTs & relay contacts for SCADA, giving power & control wiring and connections, providing terminal protector, interconnecting RMU bus bar and control cables, providing metered LT supply from nearest LT pole, providing earth leads, cable mounting & terminations, giving connections after ascertaing proper phase sequence, providing location name & warning boards, burying cables & refilling, conducting all precommissioning tests as required, complete, except cost of conveyance. Additional rate for RMUs with one additional Load Break switch / VCB

Fitting and providing one HT Stay for 11kV pole, including digging and back filling pit in ordinary soil.

Doing one cable end termination on HT XLPE UG cables of sizes beyond 3x185 sqmm and upto and including 3x300 sq mm using the cable jointing kit supplied departmentally after making fencing,caution board and all other safety measures including charges for cable jointer etc. complete as per the direction of the departmental officers.

Doing straight joint on HT XLPE UG cables of sizes beyond 3x185 sqmm and upto and including 3x300 sq mm using the cable jointing kit supplied departmentally as per specification after providing proper traffic signalling and caution board fencing etc. wherever necessary, including charges for cable jointer and other sundries etc. as per the direction of departmental officers at site.