SPL REPAIR TO BLDG NO P-340 AND PROVN OF TEMPORARY COVERED SHED FOR BSO YARD AND OTHER SANCTIONED WORK UNDER GE (A) NO.1 JODHPUR.

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness ( below or above ground level) of any description and removing rubbish to out side MD land complete all as specified and as directed.

Dismantling, stone slab, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for glazed colour ceramic tiles (premium quality) of size 250X450X6-7mm / 300X450X6-7 mm / 450X350X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for machine cut kota stone slab 20 to 25mm thick in cooking plateforms / treads (single piece) of steps from etc over screed bed base and floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20mm thick screed bed in CM 1:4 including dismantling of stone slabs of any description complete all as specified and as directed.

All as per item No.5.00 here-in-above, but kota stone (single piece) as in riser /steps (single piece), skirting/dado with 10mm thick backing coat in CM 1:4.

M&L for non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed.

All as per item No. 8.00 here-in-above, but area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm,

Taking down cement plaster any description on brick or stone walls, RCC surfaces, etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed.

M&L rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces , finished even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 10mm thick in cement mortar 1:4 on concrete ceiling /chajja/facia, finished even and smooth without using extra cement, complete all as specified and directed.

Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed.

M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed.

M&L Preparing newly/old plastered surfaces and applying with 1.5-2 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over and including M&L for one coat of primer on walls complete all as specified and as directed.

M&L for Preparation of newly/old plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M&L for Preparation of old plastered or unplastered surfaces of ceiling and applying one coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L Preparation of newly / old plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L single coat of white wash complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed.

M& L for solid PVC door frame of size 50x47mm made out of 5mm wood grain printed colour PVC sheet reinforced with MS square tube complete all as specified.

M&L for plain cement concrete 1:2:4 type B-0 by using 12.50 mm graded stone aggregate as in filling of pressed steel frames and bed block for fixing of hold fast complete all as specified and as directed.

Taking down steel windows and ventilators ( glazed / fly proof) of any description complete all as specified and as directed.

M&L factory made box type steel window side hung shutter, with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars & with or without cooler opening, dovetailed or welded and with one shop coat of zinc chromate primer (with or without cooler opening), complete all as specified and directed. Note:- (i)-:Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same. (ii)-Glass panes, guard bar & wire cloth shall be measured and paid seperately.

All as per item No. 24.00 here-in-above, but without glazing bar

S&F of Box type steel ventilator with top hung shutter including hinges with steel handle, and steel peg stay, complete with glazing bars, all as specified. Note:- (i)-:-Glass panes, guard bar & wire cloth shall be measured and paid seperately.

All as per item No. 25.00 here-in-above, but without glazing bar

M&L for mild steel work as in chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165, complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) and jointed together with solvent cement complete all as specified & directed.

S&F 100mm size butt hinges stainless steel, with stainless steel hinge pin, anodised type B-21 complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed.

S&F 200mm long, mild steel, barrel tower bolts, stove enameled black with bright bolt complete all as specified and as directed.

S&F 150 mm long, mild steel, pressed handles, oval type, stove enameled black complete all as specified and as directed.

S&F 300mm long mild steel sliding door bolts plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F for 150mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 300 mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F 125mm size single action door spring hinge complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F of 4 mm thick pinheaded figured glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and apply two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified & directed

M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed.

Taking up or down 15mm bore steel tubing or CPVC and connections including cleaning for refixing or credited to contractor complete all as specified and directed.

All as per item No 45.00 here-in-above, but size of pipe 20/25 mm bore.

Supplying, laying, testing & commissioing of CPVC pipes 20 mm outer diameter SDR 11 & Plain or brass CPVC SDR 11 fittings, laid in trenches, complete all as specified and as directed.

All as per item No 47.00 here-in-above, but size of pipe 25 mm outer dia.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting, exceeding 10 cm but not exceeding 20 cm girth complete all as specified and as directed.

S&F in replacement bib cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S & F in repairs over head shower rose 125mm dia round shape single flow ,body and face plate CP brass, arm 300mm long jointing to pipe complete all as specified and as directed.

All as per item No. 52.00 here-in-above, but angular stop valves.

S & F in repairs stop valves, 20 mm dia, cast copper alloy with capstan head, screwed down high pressure with crutch or butterfly handle with long shank and cup for iron pipe etc complete all as specified and as directed.

S & F for pillar tap, cast copper alloy, chromium plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S & F for 75mm bore PVC nahani trap with CP mild steel grating (with or without hole) including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D Type, 600 mm long between flanges including brackets complete all as specified and as directed.

S&F in replacement decorative type curtain rod stainless steel finish of pipe 22 to 25mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end, complete all as specified and as directed.

M&L 7.5 cm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4, complete all as specified and as directed.

S & F in repairs vitreous china ware wash hand basin, Ivory (brand-I), flat back of size 450 mm X 300 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore LDPE (PRESSURE RATING 4 KGf/CM2) flexible waste pipe,PVC connection15mm size with PTMT nuts of length 600mm long, complete all as specified and as directed.

S & F in replacement white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap, including M&L brackets, flush HDPE pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts & fixing arrangement of cistern, including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S&F in replacement vitreous ware wash down water closet [Pedestal Pattern], white [ETWC] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap connecting to drain pipe and flushing pipe etc., complete all as specified and directed.

Dismantling of cast iron/PVC SWR pipes of 100/110mm bore, including fittings, jointed in cement mortar complete all as specified and as directed.

All as per item No. 65.00 here-in-above, but 75 mm bore pipe

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or floor of suitable size complete all as specified and as directed .

All as per item No. 65.00 here-in-above, but 75 mm bore pipe

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with MS clamps of suitable size complete all as specified and as directed.

All as per item No. 67.00 here-in-above, but 110 mm bore pipe

S&F 110 mm bore (SWR) PVC bends any radius with access door complete all as specified and as directed.

S&F 75 mm bore (SWR) PVC bends any radius with access door complete all as specified and as directed.

S&F of PVC (SWR) 110mm bore vent cowl complete all as specified and as directed.

Supply only in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 600 mm long with PTMT nuts complete all as specified and as directed. Note:- The colour of the cistern shall be as matching with the colour of the EWC/WC Pan

M&L 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors ,hard standing flooring finishing the surface even & smooth without using extra cement complete all as specified & directed.

M&L 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified & directed

Complete removal of existing water proofing treatment of any description including bedding up to the true surface of original concrete, in RCC roof slab / stone patty and roughening the old surfaces by picking, sweeping clean and washing down with water to remove dust etc including removing rubbish to out side MD land and provide plastring 10 mm thick in CM (1:4) finished even & smooth over the RCC roof slab / stone patty for laying of water proofing treatment using water proofing compound (WPC) as per manufacturer instructionand including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastred surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using butane torch with minimum 10cm side lap and 15cm end lap complete (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confirming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : M&L 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in roof padding , the surface of concrete is to be finished even and fair with out using extra cement NOTE :- WPC shall be measured and paid separately under respective

Dismantling of existing unserviciable water tank of capacity exceeding 1000 ltrs.and removing from site.complete all as specified and as directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

Supply only integral water proofing compound (ISI marked), complete all as specified and directed.

Demolition of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L precast cement concrete (1:2:4) type B-1using 20mm graded crushed stone aggregate as in kerb stone or mud steps, coping, rounded or chamfered on edge, fixing of holdfast etc and setting in cement mortar 1:4 complete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick, PCC 1:4:8 type D2 by using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and as directed.

M&L PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in bed to drain pipe 150mm dia. Including packing under and hunching against the pipe after they are laid including necessary formwork complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and directed.

Removal of excavated material soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L factory Made flush shutters, 35 mm thick solid core with block board core construction and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match and other commercial type, as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 40mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

Removing of existing filling in sunken floor or wc/bath/kitchen and repair to sunken floor with 15 mm thick plastering in CM 1:3 of internal surfaces with bitumen 30/40 over a coat of bitumen primer putting 50 micron polythene than filling with PCC 1:5:10 type E-1 using (40 mm graded stone aggregate ) and inserting 50 mm bore GI water pipe light grade spout complete all as specified and as directed.

M & L Pressed steel frames of size 105X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed.

M & L Pressed steel frames of size 165X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed.

S&F 150 mm floor door stopper of aluminium alloy body and tongue, anodised ,with hard drawn steel spring ,fixed in floor, complete all as specified and directed.

S&F PVC door seal fixed at door to cover the gap between floor and door, complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Surface excavation n. exc. (not exceeding 30 cm deep and avg 15 cm deep) and getting out in sof/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil, complete all as specified and as directed .

Excavation in post holes each not exceeding 0.5 cu.m, getting out in any type of soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M&L for sand filling spreading and levelling in layer n.exc 25 cm thick well ramming including watering and consolidation complete all as specified and as directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, compaction/ consolidation with power roller, complete all as specified and directed.

M&L PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundation , filling and mass concerete complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified and as directed .

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in sub base of floors etc complete all as specified and as directed .

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring, coping/ benching, DPC, pier caps, bed blocks, for hold fast etc., including mixing with WPC and necessary form work, complete all as specified and as directed. Note:- WPC shall be measured and paid separately.

S&F of roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to (Fe 410-W grade E-250) quality A.complete all as specified and as directed.

S&F of plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, confirming to (Fe 410-W grade E-250) quality A. complete all as specified and as directed.

M&L for Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, including dismantling old existing roof covering sheet of any description, complete all as specified and as directed.

M&L for Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.63mm thick of any colour having tensile strength of 550 Mpa as in ridge, eaves valley gutters, hip etc., fixed with self tapping screws all as specified and as directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any description, ( colour, design & pattern, & size/ shape, as approved by GE) as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonry surfaces mixed with water proofing compound as per manufacturer instructions and finished the surfaces even and smooth with out using extra cement complete all as specified and as directed. Note :- WPC will be measured and paid seperately.

M&L for mild steel frame work in trusses purlins, posts,gates,cattle traps, etc complete using MS angle iron, MS Hollow Square or rectangular sections,flat irons etc complete incl necessary welding cutting to shape & hoisted & fixed in position complete all as directed & specified .

M&L RCC (nominal mix) 1:1½:3 type A1 by using 20mm graded stone aggregate as in beams, lintel up to 1.5 m clear span, lintel bends, plinth bends, plinth beam,roof beam, cantilevers, lintel beams, and the like complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, lintel, cantilevers, shelves , floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide includingrough finished surfaces complete all as specified and directed.

M&L TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M&L TMT steel bars of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted cement mortar 1:3 complete all as specified and directed.

S&F for sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F GI tubing (ISI marked) 15mm bore medium grade with all fittings, fixed to wall/ceiling or laid in trenches or floor and fixed complete to walls and ceiling or laid in floors, complete all as specified and as directed.

All as per item No 121.00 here-in-above, but size of pipe 20mm bore

S&F Rotational moulded polythene water storage tanks of 500 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

S & F 75mm bore PVC [SWR] Floor Trap with grating including jointing to waste pipe fixed with solvent cement, and making floor good ,complete all as specified and as directed

M&L for salt glazed stoneware drain pipes 150mm bore, grade 'A' laid in trenches and jointed in CM(1:1) including taking down old UNSV pipe, complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate), bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested, suitable for 150 mm bore pipe, complete all as specified and directed.

M&L for lintel stone 100-125 mm thick punched dressed set and pointed in cement motar 1:4, complete all as specified and directed.

M&L for fabrication of aluminium ventilators fabricated with andoised aluminium rectangular section, complete all as specified and directed.

S & F for sensor type pillar tap, chromium plated brass body fancy type (brand-I), 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F sensor type viterous china bowl lidless urinal flat back with 1.5VAA duracell battery, of size 320 x 300 x 525mm white (Minimum) with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including PVC waste coupling 32mm, waste pipe etc complete all as specified and as directed.

S&F in repairs one piece (brand-I) vitreous ware wash down water closet [Pedestal Pattern], white [ETWC] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

M&L for Modular Point wiring (Concealed) using approved colour coding as per IS Red/Yellow/Blue, Black and green for single phase circuits) with multi stranded copper conductor 1.5 Sqmm nominal cross area single core PVC insulated and unsheathed FR LS cable 1100 Volts grade ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit of dia not less than 20mm and conduit accessories ISI marked with valid CML No. as per latest IS for wall/roof /floor etc with pressed flush metal boxes covered with inner plates & outer plates etc suitable for mounting of Modular switches & sockets including PVC insulated multi stranded copper conductor FRLS 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continully conductor to commonearth and connecting to earrth dolly, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed. Note : Rate are demmed to be included in the quoted rate for cutting chesses and making good distrubed surface.

All as per Sl. Item No. 132.00 here-in-above, but one socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per Sl. Item No. 132.00 here-in-above, but one socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per Sl. Item No. 132.00 here-in-above, but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 15 Amp socket outlet on independent board .

S&F Modular switch, one module, single pole, one way 6 Amp, 230 Volts ISI Marked, complete all as specified and directed.

S&F Modular socket outlet shutter type, 2 in 1, 5 pin, 6 Amp, 230 Volts flush type, ISI Marked, complete all as specified and directed.

S&F Modular socket outlet, shutter type, 2 in 1, 6 pin, 5 and 16 amp flush type, 230 Volts ISI Marked, complete all as specified and directed.

S&F Modular switch, one module, single pole, one way, 16 Amps, ISI Marked, complete all as specified and directed.

S&F Ceiling rose, three terminals, bakelite body, 230 volts,ISI Marked complete all as specified and directed.

M & L for Lamp holder, modular type PVC/Polycarbonate type with back plate suitable for batten fitting, complete all as specified and directed.

S&F LED lamp 9 W complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long, complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable, complete all as specified and directed.

S&F electric storage water heater of capacity 25 litres BEE 5 star rated including proper installing arrangment on wall surface with suitable Anchor bolt fatser and Geyser connections for hot and cold water supply made of stainless steel wire braided connrtector with chrome finish heavy duty nuts of 15mm size with suitable lengh, including hot & cold pipe (incomming & outgoing)connetions to Chromium plated brass bib tap fancy type of size 15 mm , ISI Marked complete all as directed by Engineer-in-Charge.

S&F PVC Exhaust fan 300 mm sweep, 1000 RPM, including louvers with cutting chases on brick wall and grounting with nut bolts /fasteners, complete all as specified and directed.

S&F and testing factory made sheet metal enclosure for MCB DB TPN 4 way 415 volt with double door, IP - 43 protection duly with fixed in wall/ concealed in wall complete and making good disturbed surfaces of wall, floor etc including electric wire connection, complete all as specified and directed.

S&F MCB triple pole and neutral 415 volts 100 amps, with rupturing capacity 10 KA, 'c' curve type, with over load and short circuit protection, complete all as specified and directed.

Supply and fix MCB SPN 63 Amps, 240 Volts , breaking capacity 10KA complete all as directed

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, 240 Volts, ISI Marked Single Pole with over load and short circuit protection, complete all as directed.

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

Supply and fixing of sheet metal enclosure SPN with a two pin earth plug and socket with metal cladd top and one MCB,SP 20amps capacity complete all as specified & directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, nnected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 5 connected to Earthing test point all as ecified or indicated including testing on completion( Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover & GI 15 mm dia protection pipe upto 7.5 mtr. lead etc. complete )

S&F GI tubing (ISI marked) 25mm bore medium grade with all fittings, fixed to wall/ceiling or laid in trenches or floor and fixed complete to walls and ceiling or laid in floors, complete all as specified and as directed.

S&F PP-R ball valve of size 20 mm dia (brass insert), complete all as specified and directed.

S&F in replacement, 20 mm bore gun metal, globe or gate valve, heavy duty confirming to IS -778 with iron wheel head, screwed both ends for iron pipe, non rising forged brass spindle class I and fixed with required necessary GI fittings complete complete all as specified and directed.

M&L for cutting existing steel tubing for alterations or additions for 50/40mm bore pipe and inserting Tee equal including necessary earth work complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning 1100 volt grade heavy duty XLPE insulated LT under ground cable, sheathed, as per IS- 7098 (Part I) 1988, galvanized steel strip armoured heavy duty multi stranded aluminum conductor laid in trenches / passed through pipe/duct road crossing, fixed on poles/ wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc of size 2 core 16 sqmm complete all as specified and directed

Supply and laying Un reinforced Precast concrete cable cover, flat size 300 mm x 180 mm x 40mm, complete all as specified and directed

Supply and lay sand for sand cushioning for cable protection in trenches all as directed and specified in SSR Part - 1.Note:. for the purpose of payment punned thickness will be measured.

Supply and fix GI tubing Light grade of 40 mm dia for cable protection, complete all as specified and directed

Supply, install , Testing and commissioning High Speed auto matic Jet Hand Dryer wall mounted, material of ABS , having power load capacity 750 - 1800 W(Hot & Cold), Suitable traffic as high, current rating - 7.5 Amps, Voltage range - 220 - 240 Volts, with frequency 50 Hz, having operation - Touch Free Infra - Red Activation, Auto cut 30 Sec, Speed - 24000 RPM, Noise level - 70 db(A), with heater element, having air flow rate - 92 m/s, Drying time - 7 - 10 Sec, Motor - brushless, Blowing Volume - 180 cubic meter /hour, having protection class IPX4, Weight - 10 Kg, having warranty of High Speed Jet Hand Dryer - 24 months, complete all as directed by Engr - in Charge

NOTE:- (i)- Quantities are clubbed in BOQ for different Jobs. For which ref. Annexure-I on Sl. page. No. 41 to 43 of tender document. (ii)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

RV. Enterprises

Harsh Enterprises

M/S SUMAN ENTERPRISES