Supply Testing Installation Commissioning and demonstration of Hand Tools Instruments Equipment and Machineries of Electrician and Turner Trade at ITI Jalpaiguri

SUPPLY OF SHORT FALL OF ELECTRICIAN TRADE Course

Relay- Reverse current, 16A, 440V

Relay- Over current, 16A, 440V

Relay- Under voltage, 360V-440V

Pin type insulators including hardware fitting

Shackle type insulators including hardware fitting

Egg type insulators including hardware fitting

Suspension type insulators including hardware fitting

Laboratory Type Induction Coil, 1000 W

Knife Switch DPDT fitted with fuse terminals, 16 Amp

Knife Switch TPDT fitted with fuse terminals, 16 Amp/ 440 V

Earth Plate, 60cm X 60cm X 3.15mm Copper Plate

Earth Electrode,PrimaryElectrode2100x28x3.25mm Secondary Cu Strip 20x5mm

MCCB, 100Amps, Triple pole

Twisted Pair Cable, 1 mtr

Non-Metallic Sheathed Cable , 1 mtr

Underground Feeder Cable , 1 mtr

Ribbon Cable , 1 mtr

Metallic Sheathed Cable , 1 mtr

Multi-Conductor Cable , 1 mtr

Coaxial Cable , 1 mtr

Direct-Buried Cable, 1 mtr

Rheostat(Sliding type), 0-25Ohm,2Amp

Rheostat(Sliding type), 0- 300Ohm, 2 Amp

Rheostat(Sliding type), 0-1Ohm, 10Amp

Rheostat(Sliding type), 0-10Ohm,5Amp

Bus bar with brackets, 1 mtr each

RCC Pole with accessories (MS angle iron, ‘C’ clamp, stay insulator etc.) and materials, 6 Mtrs

Digital Multi Meter, DC 200mv -1000v,0 – 10A & AC 200mv- 750v , 0-10A, resistance 0-20 MΩ and 3 1/2 digit

Digital Wattmeter, 230 V, 1 KW, 50 Hz

Magnetic Flux Meter, 0-500 tesla

Meggar, Analog-500V

AC Starters:- Resistance type starter, For A.C Motors of 2 to 5 H.P.

AC Starters:- Star Delta Starter–Semi automatic, For A.C Motors of 2 to 5 H.P.

AC Starters:- Star Delta Starter- Soft starter, For A.C Motors of 2 to 5 H.P.

Oscilloscope Dual Trace, 20 MHz

Temperature controlled Soldering Iron, 50-Watt, 230 Volt

Immersion Heater,1500Watt,240V

Motor Pump Set,1HP,1Phase,240V

Oil Testing Kit, Oil Testing Kit, 230V,singlephase50 Hz 60 VA output 0-60 KV Variable

Inverter with Battery, 1 KVA with 12 V Battery Input- 12 volt DC, Output- 220 volt AC

DC Power Supply, 0 - 30 V, 5 A

Potential Transformer,415V,50Hz,PTRatio,440V/110V, 10 VA

AC phase-wound slip ring Motor with starter switch, 5HP,440V,3Phase,50Hz

Universal Motor with starter/switch, 240V,50Hz,1 HP

Three phase transformer, shell type oil cooled with Delta/ Star, 3 KVA , 415/240 V, 50 Hz

Diesel Generator Set with change over switch, over current breaker and water/ air-cooled with armature, star-delta connections AC 3 phase , 7.5 KVA, 415 volt or higher rating

Used DC Generators-series type for overhauling practice

Used DC Generators- shunt type for overhauling practice

Used DC Generators -compound type for overhauling practice

Ceiling fan coil Winding Machine, 250V, 50 Hz, 1-Ф, with speed control

Shaded Pole Motor, Fractional HP, 240V,50 Hz

Smart Meter,1Phase-Smart Energy Meter

Smart Meter,3Phase-SmartEnergyMeter

EV Charger, 3phase input

EV Charger (Home), 1Phase input

SUPPLY OF SHORT FALL FOR TURNER TRADE Course

Surface Plate - Granite, 1000 x 1000 mm with Stand and Cover

Marking table (CI), 120 x 120 cm with Stand and Cover

MICROMETER INSIDE, UPTO 25 TO 50 MM, LEAST COUNT 0.01 MM WITH NABL ACCREDIATED LAB CERTIFICATE

VERNIER CALIPER OUTSIDE, INSIDE AND DEPTH, 200MM / 8 INCH WITH METRIC AND INCH SCALE (LC=0.02MM) WITH NABL ACCREDIATED LAB CERTIFICATE

DIAL VERNIER CALIPER, 200MM , LEAST COUNT 0.05MM WITH NABL ACCREDIATED LAB CERTIFICATE

VERNIER BEVEL PROTRACTOR, 300MM BLADE WITH NABL ACCREDIATED LAB CERTIFICATE

VERNIER MICROMETER, 0- 25 MM O/S LC=0.001MM WITH NABL ACCREDIATED LAB CERTIFICATE

GAUGE FEELER, THICKNESS - 0.05MM TO 0.3 MM BY 0.05 MM -13 LEAVES

GAUGE FEELER, THICKNESS - 0.4MM TO 1MM BY 0.1MM -13 LEAVES

GAUGE - RADIUS SET, 1MM TO 25MM BY 0.5MM

DRILL ANGLE GAUGE, 45 DEGREE, 55 DEGREE, 90 DEGREE

MAGNIFYING GLASS, 75MM WITH MAGNIFYING FACTOR 10X

PLAIN RING GAUGE, 12,16,20,25,30,32,36,40,45,50 MM

PLAIN PLUG GAUGE, 12,16,20,25,30,32,36,40,45,50 MM

TAP &DIE , BA NO 0 TO 10 IN A BOX

TAP &DIE SET, METRIC - 3 TO 24 MM

TAP &DIE , BSF UPTO 1 INCH

TAP &DIE, BSW UPTO 1 INCH

ANGLE PLATE, ADJUSTABLE - 150 X 175 X 250 MM

TOOL MAKER'S BUTTON

HAND CHASER WITH HANDLE, M-12 & M-16 (EXTERNAL)

HAND CHASER WITH HANDLE, M-12 & M-16 (INTERNAL)

SUMIT AND COMPANY

RAMKRISHNA UDYOG