Construction of Handicapped washrooms and modifications work on the backside entrance-elevation of PEB-I Building at Tulmulla Campus CUK,Kashmir,JK

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

2.6 out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-

in- charge.

2.6.1 All kinds of soil Cum 30.00 177.50 5325.00

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

2.25 in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and Cum 25.00 196.00 4900.00

watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming,

2.27 consolidating and dressing complete. Cum 10.00 2123.75 21237.50

Providing and laying in position cement concrete of specified grade excluding the cost of

4.1 centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

4.1.3 aggregate 20 mm nominal size derived from natural sources) Cum 9.43 7878.50 74316.08

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone

4.1.5 aggregate 20 mm nominal size derived from natural sources) Cum 6.00 7294.70 43768.20

Providing and laying in position specified grade of reinforced cement concrete, excluding the

5.1 cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1cement:1.5 coarse sand:3graded stone aggregate 20mm nominal size derived from natural

5.1.2 sources Cum 6.00 9045.75 54274.50

Reinforced cement concrete work in walls (any thickness), including attached pilasters,

buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and

5.2 struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering,

finishing and reinforcement

1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size derived from natural

5.2.2 sources Cum 10.00 10852.95 108529.50

5.9 Centering and shuttering including strutting, propping etc. and removal of form for

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 40.00 392.15 15686.00

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 30.00 736.40 22092.00

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Strut Sqm 45.00 961.30 43258.50

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position

5.22A and binding all complete above plinth level.

5.22A.3 Cold twisted bars Kgs 1250.00 107.85 134812.50

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

6.1 foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum Cum 21.00 7132.25 149777.25

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation

6.13 7.5 in superstructure above plinth level up to floor V level

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 20.00 1123.80 22476.00

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining

(veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1

cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2

marble dust) with an admixture of pigment to match the marble shade (To be secured to the

backing by means of cramps, which shall be paid for separately).

8.1.1.2 Area of slab over 0.50 sqm Sqm 8.00 5938.00 47504.00

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar

8.2 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give

high gloss finish etc. complete at all levels.

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

8.2.2 Granite stone slab colour black, Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm Sqm 8.00 5136.30 41090.40

8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

8.2.1.2 Area of slab over 0.50 sqm Sqm 8.00 3078.40 24627.20

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including

8.3 machine polishing to edge to give high gloss finish etc. complete as per design approved by

Engineer-in-Charge.

8.3.1 Marble work Metre 8.00 298.60 2388.80

8.3.2 Granite work Metre 10.00 510.95 5109.50

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and

8.4 drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. Metre 8.00 568.55 4548.40

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location in marble/ Granite/ stone work, including

8.5 necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. Each 8.00 978.70 7829.60

complete.

Mirror polishing on marble work/Granite work/stone work where ever required to give high

8.6 gloss finish complete. Sqm 10.00 506.70 5067.00

Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg

9.84 to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with Each 10.00 983.15 9831.50

necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less

9.97 than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with

necessary screws etc. complete :

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

9.97.1 300x10 mm each 10.00 130.10 1301.00

Providing and fixing panelling or paneling and glazing in panelled or panelled and glazed

shutters for doors, windows and clerestory windows ( area of opening for panel inserts

excluding portion inside grooves or rebated to be measured). Panelling for panelled and glazed

9.155 shutters 25mm to 40mm thick: Pre-laminated with decorative lamination on both side exterior Sqm 10.00 1956.90 19569.00

Grade - I MDF Board 12 mm thick confirming to IS:14587

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

10.2 including cutting, hoisting, fixing in position and applying a priming coat of approved steel Kgs 8000.0 133.70 1069600.00

primer all complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified

by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such

as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4

11.37 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with Sqm 50.00 1096.55 54827.50

white cement and matching pigment etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

11.41 grouting the joints with white cement and matching pigments etc. The tiles must be cut with

the zero chipping diamond cutter only Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently

and easily.

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 m

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the

manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of

approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with

11.47 cement based high polymer modified quick set tile adhesive (water based) conforming to IS:

15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints

to be made separately).

11.47.2 Size of Tile 600x600 mm Metre 34.00 1893.90 64392.60

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

12.41.1 75 mm diameter Metre 150.00 248.80 37320.00

12.41.2 110 mm diameter Metre 150.00 377.40 56610.00

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

12.42 with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

12.42.1 Coupler

12.42.1.2 110 mm Each 12.00 136.15 1633.80

12.42.3 Single tee with door

12.42.3.2 110x110x110 mm Each 8.00 234.15 1873.20

12.42.5.2 110 mm bend Each 20.00 150.35 3007.00

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

Providing and fixing false ceiling at all height including providing and fixing of frame work made

of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm

wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,

other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts

& bolts of required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips

of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire

at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges

of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of

size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recomme-nded jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and

two coats of primer suitable for board, all as per manufacturer’s specification and also including

the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of painting with

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 80.00 1529.10 122328.00

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of

corrugation as approved by engineer in charge) .50 mm (-0.05%) total coated thickness with

zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade. 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have

protective guard film of 25 microns minimum to avoid scratches during transportation and

12.50 should be supplied in single length upto 12 mtr or as desired bt Engineer in charge. The sheet Sqm 60.00 738.65 44319.00

shall be fixed using self-drilling /self-tapping screws of size (5.5 X55 mm) with EPDM seal.

complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purlins

rafters and trusses and including cutting to size and shape wherever required.

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %)

total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel

12.51 grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18

microns using self drilling/ self tapping screws complete

Ridges plain ( 500-600mm)

Gutter (600 mm over all girth

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

13.26 prepare the surface even and smooth complete. Sqm 100.00 262.70 26270.00

Applying one coat of water thinnable cement primer of approved brand and manufacture on

13.41 wall surface :

13.41.1 Water thinnable cement primer Sqm 100.00 185.65 18565.00

With ready mixed aluminium primer of approved brand and manufacture on resinous wood &

13.50.2 plywood Sqm 150.00 74.65 11197.50

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per

13.52 manufacturer's specifications including appropriate priming coat, preparation of surface, etc.

complete.

13.52.1 On steel work Sqm 20.00 241.75 4835.00

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade

13.62.1 Two or more coats on new work Sqm 50.00 226.25 11312.50

13.67 Varnishing with varnish of approved brand and manufacture :

Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

Dismantling tile work in floors and roofs laid in cement mortar including stacking material

15.23 within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 40.00 73.40 2936.00

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of

15.41 serviceable materials and disposal of unserviceable materials within 50 metres lead. Sqm 300.00 56.35 16905.00

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking

15.44 out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres

lead as per direction of Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore Metre 60.00 149.80 8988.00

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling

including disposal of unserviceable material and stacking of serviceable material with in 50

meters lead as directed by Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan)

with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with

17.2 manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and floors wherever required

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 2.00 6515.55 13031.10

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P.

brass waste of standard pattern, including painting of fittings and brackets, cutting and making

good the walls wherever require:

White viterous china wash basin size 630 *450mm with a pair of 15mm C.P brass pillar taps.

17.28 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete

17.28.2 Flexible pipe

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

17.28.2.1 32 mm dia Each 20.00 119.55 2391.00

17.28.2.2 40mm dia Each 20.00 119.55 2391.00

Providing and fixing mirror of superior glass (of approved quality) and of required shape and

17.32 size with plastic moulded frame of approved make and shade with 6 mm thick hard board

backing :

17.32.2 Rectangular shape 453x357 mm Each 10.00 1361.80 13618.00

17.34 Providing and fixing toilet paper holder :

17.34.1 C.P. brass Each 6.00 803.70 4822.20

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and

17.69 colour.

Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260

17.70.1 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, Each 6.00 367.10 2202.60

weighing not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm

17.71 distance from wall of standard shape with bracket of the same materials with snap fittings of Each 6.00 168.35 1010.10

approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with

17.72 minimum distances of 37 mm from wall face with concealed fittings arrangement of approved Each 6.00 231.95 1391.70

quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP

brass screws with concealed fittings arrangement of approved quality and colour

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88

17.73.2 mm, weighing not less than 190 gms. Each 3.00 708.95 2126.85

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to

IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold

water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c

18.5 fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and

making good the same including testing of joints complete as per direction of Engineer-in-

Charge.

Concealed work,including cutting chases and making good the wall etc. 0.00

18.5.1 PN - 16 Pipe, 20mm OD (SDR-7.4) Metre 150.00 477.85 71677.50

18.5.2 PN - 16 Pipe, 25mm OD (SDR-7.4) Metre 150.00 515.20 77280.00

18.5.3 PN - 16 Pipe, 32mm OD (SDR-7.4) Metre 150.00 561.45 84217.50

Providing & Fixing 3 layer PPR pipes confirming to IS:15801 UV stablized &anti microbial fusion

welded,having thermal stablity for hot &cold water supply,including all PP-Rplain & braaa

18.6 threaded polupropylene random fittings,including trenching,refilling & testing of joints

complete as per direction of Engineer -Incharge

18.6.1 PN-16Pipe,20mm OD (SDR-7.4) Metre 45.00 224.95 10122.75

18.6.2 PN-16Pipe,25mm OD (SDR-7.4) Metre 100.00 265.05 26505.00

18.6.3 PN-16Pipe,32mm OD (SDR-7.4) Metre 200.00 316.25 63250.00

18.49 Providing & Fixing C.P brass bib cock of approved quality conforming to IS:8931

18.49.1 15mm nominal bore Each 15.00 506.80 7602.00

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved

18.53 quality conforming to IS:8931

18.53.1 15 mm nominal bore Each 50.00 574.30 28715.00

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

18.58 Providing and fixing PTMT grating of approved quality and colour

18.58.1 Circular type

18.58.1.1 100 mm nominal dia Each 12.00 37.60 451.20

Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

21.1 required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium

snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kgs 200.00 530.90 106180.00

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

21.1.2 making provision for fixing of fittings wherever required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kgs 100.00 634.45 63445.00

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded

wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum

21.2 doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc.

complete as per architectural drawings and directions of engineer- in-charge

21.2.2 Pre-laminated particle board with decorative lamination on both sides Sqm 22.00 1115.40 24538.80

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the

21.3 directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 0.00

21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 50.00 1505.25 75262.50

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

Providing and fixing double action hydraulic floor spring of approved brand and manufacture

conforming to IS : 6315, having brand logo embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding

21.4 in floors as required and making good the same matching to the existing floor finishing and

cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc.

complete as per the direction of Engineer-in-charge.

21.4.1 With stainless steel cover plate minimum 1.25 mm thicknes Each 20.00 2823.85 56477.00

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of approved quality as per architectural drawings and

direction of Engineer-in-charge complete.

21.8.1 Upto 5mm depth and 5 mm width Metre 40.00 96.75 3870.00

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand

and manufacture, including providing and fixing top & bottom pivot & spring type fixing

21.18 arrangement and making necessary holes etc. for fixing required door fittings, all complete as Sqm 40.00 5325.90 213036.00

per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by

applying cement slurry mixed with water proofing cement compound consisting of applying :(a)

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @

0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of

22.5 cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This Sqm 80.00 617.05 49364.00

layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate

includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes

and masonry with polymer mixed slurry.

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST

Item No DSR-

Description of Items Unit Qty Rate Amount

Providing & fixing complete set of HWC toilet including following items complete of approved

make WC including INLET OUTLET GASKET CAT NO ZPS - WHT-GKO1 , Seat cover , Cistern

, Wash Basin with bottel trap , Set of three Grab Bars

1.) EWC 710x370x770mm one piece EWC S trap 300 mm

2.) Soft Close Seat Cover

NS-1 Each 4.00 62174.24 248696.94

3.) Crane Wall hung wash Basin 665x545x1790 mm

4.) Singal Lever Clinical faucet

5.) Wall Mounted Grab Bar 600 m long 2 No.

6.) Wall Mounted hinged grab bar rail 750x100 mm

TOTAL 3891464.00

Digitally signed by Om Prakash

Date: 2024.01.31 12:16:37 IST