Annual Rate Contract for Shifting of RMU and UG Infrastructure at various area of KALOL-2 Sub Division

Sub Division SCHEDULE-B

Description Qty Unit Rate Amount

Erection of 3-way RMU with PLINTH including material

without RMU as per specification

Erection of 4-way / 5-Way RMU with PLINTH including

material without RMU as per specification

Extension of existing plinth : Construction of RMU Plinth

(Extension of One way)

Erection of Double pole structure of 10 meters X 270 kg

PSC poles including excavation of pits & refilling of

earthing, fixing of channels, supporting angles ,clamps,

anti-climbing devices danger boards, insulators etc.

complete and painting of fabricated materials used on the

poles and numbering without cost of nuts & bolts with

cost of paint as per standard specification but excluding

erection of guy sets and earthing.(Without AB Switch)

Construction of Plinth for installation of Transformer (up

Construction of Plinth for installation of Transformer (630

& 800 KVA) 3.15 x 2.90 x 0.75 Meter above ground

Construction of Plinth for installation of Transformer (1000

KVA) 3.15 x 3.40 x 0.75 Meter above ground

Construction of Plinth for installation of Transformer (1250

KVA) 3.15 x 3.65 x 0.75 Meter above ground

Normal Laying: Laying of various size Single Circuit of 11kV

XLPE insulated Aluminum armoured cable in Cable trench

up to the minimum depth of 1200 mm is to be dug with

width of 300 mm in any type of soil. Spreading of sand at

the bottom of the trench up to 100mm before lying of

power cable in the centre of the trench. Spreading of

another layer of 100mm sand above laid cable. Utmost

care should be taken while loading / unloading and

unwinding the cable drums. Covering the cable with RCC

half round hume pipe 30mm thick, 150mm inner

dia.before refilling pre-bonding tap/warning tap should

provide below 700 mm from the ground level and back

filling the same to make ground level as per original., Back

feeling the trench so as to make ground level as per

original. Laid cable up to cable box of Plinth Mounted RMU

/ Transformer shall be part of Normal Laying. [The rates

are exluding supply of cable]. (185/240/300 SQMM Cable

Signature of Contractor & seal

Division Office: Kalol, Mahendra Mill Road, Kalol (N.G)-382721, Telephone : (02764)223773

E-Mail:- [email protected] Website: www.ugvcl.com

Save Energy for Benefit of Self and Nation

SINGLE LOGO LETTERHEAD

Normal Laying: Laying of various size Double Circuit of

11kV XLPE insulated Aluminum armoured cable in Cable

trench up to the minimum depth of 1200 mm is to be dug

with width of 500 mm in any type of soil. Spreading of

sand at the bottom of the trench up to 100mm before lying

of power cable in the centre of the trench. Spreading of

another layer of 100mm sand above laid cable. Utmost

care should be taken while loading / unloading and

10 unwinding the cable drums. Covering the cable with RCC 50 MTR 468

half round hume pipe 30mm thick, 150mm inner dia before

refilling pre-bonding tap/warning tap should provide below

700 mm from the ground level and back filling the same to

make ground level as per original., Back feeling the trench

so as to make ground level as per original. Laid cable up to

cable box of Plinth Mounted RMU / Transformer shall be

part of Normal Laying.[The rates are excluding supply of

Laying of various sizes of 1.1 KV XLPE insulated Aluminum

armoured cable in cable tray/ trench over/below the

ground level [The rates are excluding cable tray, only

labour charges].

Laying of various size of 1.1 KV XLPE insulated Aluminum

armoured cable above ground in air for termination of

12 cable on Pole as per site condition and instruction of 50 MTR 38

engineer in charge [The rates are excluding cost of clamp

Providing of OD 160 mm HDPE Pipe, minimum thickness as

per IS 4982 and amendment thereof, confirming to IS

4984:1955 (Amendment no. 2) for HT UG Cable [Rates are

excluding laying of cable]

Laying by Push Through of OD 160 mm HDPE Pipe,

minimum thickness as per IS 4982 and amendment thereof,

confirming to IS 4984:1955 (Amendment no. 2) for HT UG

Cable [Rates are excluding laying of cable]

Providing of OD 110 mm HDPE Pipe, minimum thickness as

per IS 4982 and amendment thereof, confirming to IS

4984:1955 (Amendment no. 2) for HT UG Cable [Rates are

excluding laying of cable]

Laying by Push Through of OD 110 mm HDPE Pipe,

minimum thickness as per IS 4982 and amendment thereof,

confirming to IS 4984:1955 (Amendment no. 2) for HT UG

Cable [Rates are excluding laying of cable]

Supply installation & commissioning of earthing conductor

40 x 3 G.I. strip for all electrical equipments as well as

connection to be made. Rates inclusive of hot dipped

Signature of Contractor & seal

Division Office: Kalol, Mahendra Mill Road, Kalol (N.G)-382721, Telephone : (02764)223773

E-Mail:- [email protected] Website: www.ugvcl.com

Save Energy for Benefit of Self and Nation

SINGLE LOGO LETTERHEAD

Supply installation & commissioning of earthing conductor

38 x 3 G.I. strip for pole mounted transformer and up to

FSP,RMU as well as connection to be made to the earth

pit. Rates inclusive of hot dipped hardwares.

Supply installation & commissioning of earthing conductor

25 x 3 G.I. strip for pole mounted transformer and up to

FSP,RMU as well as connection to be made to the earth

pit. Rates inclusive of hot dipped hardwares.

Carbon Earthing for UG Equipment: Supplying & erecting of

maintenance free earthing system comprising of 17.2 mm

dia 3 mtr Long Earthing Electrode of low carbon steel

electrode with 250 micrns copper coating + carbon based

conductive concrete back fill safe compound(resistivity of

less than 0.10 ohm mtr) & copper clamp.Making 100 mm

Dia Bore, 3 Mtr Long, Making of Earth pit chamber in

providing & fixing HT push on/heat shrink type end indoor

21 termination kit (Any make approved by GUVNL & Its 10 Nos. 4927

Subsidiaries Company)(70 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end indoor

22 termination kit (Any make approved by GUVNL & Its 10 Nos. 5162

Subsidiaries Company)(120/150/185 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end indoor

23 termination kit (Any make approved by GUVNL & Its 10 Nos. 5461

Subsidiaries Company)(240 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end indoor

24 termination kit (Any make approved by GUVNL & Its 10 Nos. 5758

Subsidiaries Company)(300/400 mm2 HT XLPE cable

providing & fixing HT push on/heat shrink type end

25 Outdoor termination kit (Any make approved by GUVNL & 10 Nos. 5873

Its Subsidiaries Company)(70 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end

Outdoor termination kit (Any make approved by GUVNL &

Its Subsidiaries Company)(120/150/185 mm2 HT XLPE

providing & fixing HT push on/heat shrink type end

27 Outdoor termination kit (Any make approved by GUVNL & 10 Nos. 6587

Its Subsidiaries Company)(240 mm2 HT XLPE cable

providing & fixing HT push on/heat shrink type end

28 Outdoor termination kit (Any make approved by GUVNL & 10 Nos. 6885

Its Subsidiaries Company)(300/400 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end

29 Straight Joint (Any make approved by GUVNL & Its 10 Nos. 7408

Subsidiaries Company)(70 mm2 HT XLPE cable )

Signature of Contractor & seal

Division Office: Kalol, Mahendra Mill Road, Kalol (N.G)-382721, Telephone : (02764)223773

E-Mail:- [email protected] Website: www.ugvcl.com

Save Energy for Benefit of Self and Nation

SINGLE LOGO LETTERHEAD

providing & fixing HT push on/heat shrink type end

30 Straight Joint (Any make approved by GUVNL & Its 10 Nos. 7864

Subsidiaries Company)(120/150/185 mm2 HT XLPE cable )

providing & fixing HT push on/heat shrink type end

31 Straight Joint (Any make approved by GUVNL & Its 10 Nos. 8089

Subsidiaries Company)(240 mm2 HT XLPE cable

providing & fixing HT push on/heat shrink type end

32 Straight Joint (Any make approved by GUVNL & Its 10 Nos. 8249

Subsidiaries Company)(300/400 mm2 HT XLPE cable )

33 Erection of FSP/MSP 1250 / 800 / 650 / 400 AMP 15 Nos. 2811

Erection of Plinth and foundation for FSP/MSP 1250 /

LT CABLE TERMINATION OF ANY SIZE OF LT CABLE : Cable

termination (Indoor / Outdoor / Straight Joints) on LT

Pole, FSP, LT Distribution Transformer Box of pole

35 mounted transformer of LT cable grade as specified below 10 Nos. 125

including cutting, stripping of cable, insulations, providing

compression type terminals including supply of suitable

cable glands, crimping lugs with necessary connections.

Replacement of Transformer (irrespective of kVA Rating):

Existing Transformer with Cable Box shall be dismantled

and New Transformer with Cable Box shall be installed.

Existing Transformer with Cable Box shall be submitted to

UGVCL Store as per instruction of Engineer - in - Charge.

Termination, earthing etc. shall be billed separately.

Replacement of RMU (irrespective of configuration):

Existing RMU shall be dismantled and New RMU shall be

37 installed. Existing RMU shall be submitted to UGVCL Store 5 Nos. 8850

as per instruction of Engineer - in - Charge. Termination,

earthing etc. shall be billed separately.

37 Installation Testing and commi. Of RMU on new plinth 10 Nos. 4425

38 Dismantling Of RMU from Old plinth 10 Nos. 2250

39 Dismantling/Demolition of Old unused plinth 20 Nos. 2000

40 Welfare Cess @ 1% 1 Each 39933

TOTAL WITH WELFARE CESS

NET TOTAL WITH 18% GST &1% WELFARE CESS

Executive Engineer

Signature of Contractor & seal

Division Office: Kalol, Mahendra Mill Road, Kalol (N.G)-382721, Telephone : (02764)223773

E-Mail:- [email protected] Website: www.ugvcl.com