SPECIAL REPAIRS/ REPLACEMENT OF BER LIFTS INCLUDING 03 YEARS COMPREHENSIVE MAINTENANCE AT VARUNA APARTMENTS ELAMKULAM KOCHI

Amount

SCHEDULE 'A' PART I

M&L for dismantling of existing old Lift of 13 passenger capacity upto 10 floor (G+9) from Varuna apartments at Elamkulam, Kochi complete including car, guide rail, counter weight, drive machine with motor, control panels etc and depositing to MES store yard including making good the disturbed surfaces.

Make:- M/S Kone India / M/s Schinder India Pvt Ltd / M/s Kinetic Hyundai Elevator & movement Technologies Ltd / M/s Hitachi Lifts India Pvt ltd / M/s Mistubishi Elevator India pvt Ltd / M/s Otis elevator company India Ltd / M/s Fujitech India Pvt Ltd / M/s Thyssenkrupp Elevators pvt Ltd. NOTE :-Existing Lift Well / Shaft Size : Approx 2500mm (W) x 1800mm (D), Pit Depth : 1600mm Clear Door Opening : 900mm (W) x 2000mm (H)

Note for item No. 2 :- 1. Work has to be executed in pre-occupied condition bldg and shall take care of all safety measures and avoid disturbances to the occupants while carrying out the work. 2. Contractor shall not dump any materials in the premises of the bldg which may cause hindrance to the users. 3. The lifts are to be installed in existing lift shaft / well. 4. Any addition / alteration cost required for the erection of new lift is deemed to be included in quoted rate. 5. The following items shall be provided and the unit rate quoted above shall be inclusive for the same . (a) Gearless Electric motor, AC, 3 phase, 415V, 50Hz of suitable capacity including necessary cabling with ISI marked FRLHS Cable and fire resistant conduits as required. (b) Standard Wall / Floor mounted Lift Control Panel Board with suitable capacity 4 pole RCCB as incomer. (c) Mechanical guide rail in 'T' section with tongue and groove arrangement for smooth operation of car and counter weight. (d) Type of operation shall be single automatic push button type . (e) Minimum 4Nos SS Finish 3W LED Fittings and 02 Nos blower Fan with Switch in lift car. (f) Minimum 08Nos 7/9W LED Bulk Head Fittings for lift well lighting and 08Nos 5Amps Plug Point incl point wiring with 1.5Sqmm FRLHS cables and control switches. (g) Type of signal system - Hall button with digital hall position indicator, digital car position indicator in car fixtures in stainless stell face plates. (h) Capacity of ARD battery (High Amp Hour) should be suitable to perform minimum three continous rescue operation . (l) All necessary Grouting Plates / Bolts, Nuts, bolts, washers etc. (j) Provision of hoist way and governors rope and governor. (k) Provision of new buffer spring as per manufacturers design. (l) Provision of battery operated alarm and emergency light through inverter of suitable capacity having power back up for a period of minimum 30 minutes . (m) Drive - Permanent Magnet Gearless Machine frame fixed in the machine room. (n) Over speed governor monitors the speed and triggers safety gears etc shall be installed in the machine room. (o) Necessary scaffoldings in lift well. (p) Pit Ladder. (q) 02 Nos 600x600x3mm coper plate independent earthing duly connected with 20x3 copper strip from earth plate to control panel in machine room through lift well incl necessary earth looping to motor, electrical gadget etc Complete

Safety Measures:- (i) Overload relays. (ii) BMS Compatibility / Potential Free Contactors (Emergency Stop / Opening, Direction Up / Down, Failure, Main mode etc. and fuses. (iii) DO /DC Button and NS Button. (iv) High Quality Electrical Terminals / Sockets. (v) Limit switch with accessories on each doors / cage. (vi) Gravity / counter weight limit switches for top most position. (vii) Break Magnet of suitable size with manned released arrangements. (viii) Reverse Phase / Phase sequence corrector. (ix) lift door should be minimum 2 Hrs. fire resistance as specified in IS-14665. (x) Automatic condition monitoring of Polyurethane - Coated Steel Belt to ascertain it's mechanical integrity real time. (xi) Hoist way Access Prevention Special Safety Feature to prevent the elevator from operating after landing door is opened.

M&L 20 mm thick pre-polished Granite slab of approved colour, machine cut, set and jointed in neat cement slurry and pointed with white cement with admixture of pigments to match the shade of granite tile including grinding and polishing wherever required at site as in skirting/Dado / face of lift over and including cement mortar 15mm thick in CM 1:3 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone complete all as specified and directed.

Taking down cement or cement lime plaster from brick or PCC block or concrete wall etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Total of Schedule 'A' Part I

Schedule 'A' Part II

All as per item No.2.01 above, but for Second year after expiry of defects liability period (ie for one year after completion of first year maintenance period vide item No.2.01 above)

All as per item No.2.01 above, but for Third year after expiry of defects liability period (ie for one year after completion of second year maintenance period vide item No.2.02 above)

Total of Part II

Escon Elevators Pvt Ltd

M/S CH RAM CHANDER

Veer High Tech Solution

MB Enterprises

INDUSTRIAL ENGINEERING SYSTEMS