PROVN OF TOILET BLOCK CUM BATHROOM, PARKING SHED, COVERED SHED, STORAGE SHED, FOL STORE, FLOOR TILES, GLASS DOOR, STORE ROOM, OVERHEAD RAIN SHELTER, ROLLING SHUTTERS AT ARMY AVN SQN, ENGR REGT, ENGR PRAK, ASC COY, CORPS ZONAL WKSP, TOR COMPLEX, NEW J

Amount

Surface excavation n exe 30 cm deep and averaging 15 cm deep in soft/ loose soil and getting out.

Excavating in trenches n.exe. 1.5 m width and n.exe. 1.5 m in depth for foundation in soft/loose soil & getting out..

Returning filling in , including spreading,levelling,watering & well ramming in layers not exc 25 cm.

Removing excavated material n exc 50 m & depositing where directed at a level n exc 1.5 m.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation.

M&L for RCC nominal mix Type B1 1:1.5 :3 (using 20 mm graded aggregate) for beams, cantilevers, bressumers, lintel over 1.5 m span.

M & L for TMT reinforcement 10 mm dia and over cut to length bent to shape including cranking, hooking etc binding with mild steel wire not less than 0.90 mm dia (annealed) all as directed complete.

S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as in including cutting, bending and binding with mild steel not less than 0.9 mm dia (annealed) all as directed complete.

Form work for foundation footing , bases of columns & plinth beams similar work vertical or batter.

M&L for Pre-cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in landing, cover slabs (for manhole covers, drains etc) set in CM 1:6 complete all as specified.

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed.

M&L for brick work with burnt old size bricks built in cement mortar 1:4 straight or curved on plan to any radius in half brick thick walls and all as directed.

M&L40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) mixed with WPC ( WPC shall be measured & paid separately

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth.

M&L for 20mm thick plaster on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of conc work to wall surface and the surface is finished even and smooth without using extra cement

Supply only integral WPC

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course/Hardstanding as directed by engineer in charge.

M&L Sand filling under floors or in foundations including watering and conosoldiation.

M&L for broken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface.

M&L for 100mm thick PCC type D2 1:4:8 using (40mm gradded aggregate) as in sub base.

M&L for Non skid ceramic colour joint free tiles 7 to 8 mm thick area each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in net cement slurry and pointed in white or coloured cement to match incl screed bed 15 mm thick of CM 1:6 .

M&L for Pre-polished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 450x 350x 7 mm thick set and jointed in neat cement slurry & painted in white or colour cement to match incl 10 mm thick backing coat in CM 1:4 .

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening as per specification & as directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and as directed.

S&F for window/ventiletor shutters, side hung type without sash bars aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips,ruber neoprene packing,anodised aluminium snap beading screws,anodised aluminium fittings such as peg stays 150 mm long(1 no),hinges type-B-21 100 mm long( 2 no) suitable handle 1 no complete all as specified incl powder coating of any colour (thick ness of powder coating not less than 50 micron).

S&F pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam tee, angle, channel or flat sections) including clits etc conforming to Fe-410-0 or Fe-310-0.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section

S&F aluminium alloy 200mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed.

S&F 100mm MS butt hinges medium weight

S&F aluminium handle cast type anodised 150mm size

S&F 15mm bore GI tubing medium graded with all fitting and fixed complete to wall and ceiling or laid in floor .

All as per item No 34 here in before but 20mm dia

S&F 20 mm Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S& F for Vitreous China (Pedestal pattern) Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. pipe) incl PVC seat cover complete in all respect all as specified. “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe)

S&F for health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified.

S&F for 10 Ltrs. Capacity PVC flusing cistern low level slimline or equivalen make / model with all accessories.

S&F Vitreous china urinals, half stall type, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws.

S&F 15mm bore bib tap cast copper alloy fancy type chromium plate with crutch or butter fly handle screwed down for iron pipe but fancy type.

S&F 15mm bore stop cock/valve cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both end for iron pipe complete.

S&F PVC connector 600mm long with brass coupling in both ends screwed down for iron pipe.

S&F 15mm bore piller tap fancy type cast copper alloy with capstin head CP screwed down high pressure with or without littered 'H' or 'C' with long screwed shank and fly nuts screwed for iron pipe etc complete.

S&F vitreous china wash basin white, flat back, size 550x400mm excluding taps , waste ,but including barkets.

S&F 32mm bore dia Waste coupling of PTMT (half or full threaded) minium weight 45 gms)

S&F stainless steel Soap dish, any type, fixed to wall with chromium plated brass screws

S&F Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F 100mm dia PTMT grating.

S&F 75 mm thick PVC (SWR pipes single socketed in any length with rubber ring joints laid in trenches or floors.

S & F 75 mm bore PVC (SWR) bends of any radius.

M&L 100 mm bore for cast iron Nahani trap with grating incl jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed in walls.

S & F 110 mm bore PVC (SWR) bends of any radius.

Supplying, laying and testing of 150 mm internal dia of double wall corrugaed (DWC) high density polythylene pipe (HDPE) and stiffness classes 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for connection of inspection chamber/WC to first manhole of the sewage line complete all as specified and directed.

Cutting into existing manholes of 150 mm dia for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required.

M&L for Hoisting & fixing 1000 litres Rotational moulded polythylene water stroage tanks (cylindrical vertical with closed top) hoisted & fixed in position all position all as specified in SSR part -I incl all necessary fittings.

S&F 20 mm dia ball valves, PTMT high pressure of epoxy coated Aluminium rod and high density plastic ball (200 gms) complete, screwed for iron pipes or brasas ferrule and fixed.

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered surface to prepara-tory to distempering complete all as specified and directed.

M&L two coats of cement base paint over a coat of primer on wall surface including preparation of surface..

M&l Painting two coats of synthetic enamel paint over a coat of red oxide primer to new steel Surfaces of any description, not otherwise described, over 10cm width or girth.

S&F for anodised powder coated aluminium ventilator with frame of weight not less than 0.75 Kg/ RM and shutter of weight not less than 0.55 Kg/ RM lowers type incl necessary fittings and 4 mm thick frosted glass, complete all as specified and directed.

M&L for RCC Nominal Mix type B1 1: 1.5 : 3 (using 20 mm graded aggregate) for raft foundation footing ,bases of columns, plinth beams Lintel beam & mass concrete.

M&L for RCC Nominal Mix type B1 1: 1.5:3 (using 20 mm graded aggregate) for columns, pillars,posts and struts, complete all as specified and directed.

M&L for RCC Nominal Mix type B1 1: 1.5 :3 (using 20 mm graded aggregate) for slab supported on wall, beams and columns, roof, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L for RCC Nominal Mix (1:2:4) using 20 mm graded aggregate for chajjas.

Form work for side of pillars, posts, columns & similar works vertical or batter.

Form work to side & soffits of floor or roof beams, slab, lintels & similar works.

Form work to soffits of roof slab & similar works.

M&L for rendering 5 mm thick on ceiling or concrete Surfaces in cement mortar 1:3 finished even and smooth.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in net cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of cement mortar 1:6,15 mm thick for laying floor finishes.

M&L for powder coating Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares exceeding 0.50 Sqm in each pane

S&F aluminium alloy 250mm anodised sliding door bolt with hasp, staple (bolt type ) & fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy of fixed.

S&F 100mm aluminium alloy butt hinges medium weight

M&L two coat of white wash on ceiling surface including preparation of new surface complete all as specified and directed.

M&L three coats of white wash on wall surface including preparation of new surface complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application including coating the surface with water based bituminous primer blow bitumen of 85/25 or 90/15 at 1.2 Kg/Sqm both at bottom and top of the membrance and finally finished with one coat of bitumenous aluminium paint at 100 gm per sqm incl 10mm rendeing in CM 1:4 complete all as specified.

Supply and laying 20 mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply and laying 25 mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply & Fix Vitreous china wash down water closet pan (pedestal pattern) white with includig 'P' or 'S' traps.

S & F Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union

S & F 110 mm bore PVC (SWR) Vent Cowl

S&F Exterior designer tiles of size 300x300x18 to 20mm thick in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor including 15mm thick screed bed in cement mortor 1:4 complete all as specified and as directed

M&L for Glazed ceramic coloured tiles in vertical surfaces 450x 300x 7 mm thick set and jointed in neat cement slurry & painted in white or colour cement to match incl 10 mm thick backing coat in CM 1:4 .

S&F for Anodised aluminium/ GI snap grid power coated framed work of size 605x605 mm for false ceiling all as specified with hangers 4mm thick GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified and as directed.

M & L for 4mm thick Non Asbestos designed Cement E board as approved by GE of size fixed in ceiling as specified and directed.

M&L for Granite of any type 20 mm thick machine cut bedded and jointed with grey cement slurry and pointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete incl 20 mm thick screed bed 1:6 CM.

S&F Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard and railing 60cm long fixed to wall complete all as specified and directed.

M&L 100 mm bore for PVC (SWR) Floor trap with grating incl jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed

S&F 30 mm thick 2nd class HW Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Second class hard wood kiln seasoned and chemically pressure treated plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 conforming to Fe-410-W Gde E-250 quality -A

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered surface to prepara-tory to distempering complete all as specified and directed over 1 mm thick wall care putty.

Excavating in post holes (or similar holes) each n exc 0.5 cum,in Hard/dense soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L cement concrete with PCC type B2 1:3:6 using 40mm graded aggregate as in foundation filling and mass concrete.

Surface dressing in soft loose soil n exc 15 cm deep and getting out.

M&L for 100mm thick PCC 1:2:4 type B2 using 40mm graded aggregate as in plinth course/Hardstanding/Flooring as directed by engineer in charge.

Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedded and pointed in any morter etc

M&L Heavy duty Coloured Ceramic Tiles 600x600x 15mm thick, in Floors, set and jointed in Neat Cement Slurry and pointed in White Cement mixed with Pigment to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame)

S & F 12 mm thick toughened glass as in hinged doors, partition automatic doors and similar work including cutting to shape, drilling holes as requirte including necessary bottom and top latch and floor spring and two Nos stainless steel handles, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for preparation of newly plastered surfaces of walls any description and applying two coats of oil bound Distemper over one coat of primer over 1 mm th putty complete all as specified and as directed.

M&L for Polythene film, black, 50micron laid in floors

M&L for 40mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) finish smooth using extra cement.

M&L for Plastic dividing strips, 1.5mm thick inserted in position,conform to design

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides.

S&F for anodised Alum three track sliding window and ventiletor frame side/top made up 123.45 mm /44 mm 1.5 mm thick bottom 128.00mm/ 39.15mm / 1.63mm aluminium section & shutter made up 69 mm / 25.40 mm/1.63 mm and 50.80 mm/ 25.4mm/ 1.63mm thick without sash bar alum section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment etc , two track for glass and one track for aluminium wire mesh etc as directed by engr in charge . incu power coated of any colour (thick of power coating not less than 50 micron ) & prividing AC hole as directed by engr in charge.

S & F 4 mm thick Sheet glass, ordinary quality and glazing with wooden beads in squares not exceeding 0.5 Sq. M in each pane

Supplyand fixed Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for 100mm thick PCC type B2 1:2:4 using (20mm gradded aggregate) as in sub base.

M&L for 150mm thick PCC type B2 1:4:8 using (40mm gradded aggregate) as in sub base.

M&L for forming contraction joints(Dummy) joints 50 mm deep 10 mm wide filled with sealing compound Grade A.

S&F rolled mild steel in compound girders and stanchions, lattice girders, aerial masts,angle, staging for water tanks and the like including caps, bases, splices etc built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates,etc.

M&L cement concrete with PCC type C2 1:3:6 using 20mm graded aggregate as in surface channel etc

S&F Steel rolling shutters 1.25mm thick, with ball bearing, gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, incl safety lever locks mild steel with 4 levers for rolling shutters including making good disturb area complete all as specified and directed.

S&F Gl frame work for seamless ceiling Size of grid 605mm x 605mm comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

S&F 12 mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish

M&L Vitrified Ceramic tiles dark shade 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded aggregate as in sub base complete all as specified and directed

M & L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

S&F for Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60 gms)

M&L for Hoisting & fixing 500 litres Rotational moulded polythylene water stroage tanks (cylindrical vertical with closed top) hoisted & fixed in position all position all as specified in SSR part -I incl all necessary fittings.

Material and labour for point wiring with 1.5 sqmm (nominal area) FRLSH PVC insulated stranded copper conductor single core including PVC conduit of appropriate size concealed in wall, pressed steel concealed terminal boxes of required size and with top cover 3 mm thick of plastic laminated sheet of reqd colour, painting terminal boxes inside and out side with one coat red oxide primer complete with all accessories and all as specified including 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper earth conductor to common earth and connected to earth dolly for fan / light / exhaust fan/ bell point controlled by one switch. Note:- 1. Cost of PVC conduit, steel terminal boxes, plastic laminated sheet cover etc; are deemed to be included in the quoted rate. 2. Cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3)and ,putty and plastic paint matching with existing surface etc; shall be deemed to be included in the rate quoted above. : (a) One light point controlled by one, one way switch 5 Amps

(c) One 3 point 5 Amps socket outlets point controlled by one switch on the same board

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

All as per item No 139 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board.

S & F Switch piano (White) flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Socket outlet (White) 2 in 1,5/6 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination (White) flush type multipurpose 5/6 pin 5 Amps two in one , 230 volts complete all as specified .

S&F Switch socket combination (White) 2 in 1 5/6 pin, 15 Amp flush type universal.

S&F ceilling rose (White) three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all specified .

S & F Lamp holder (White) with insulated body, with back plate suitable for batten fittings complete all as directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make-

S & F sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified.

S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative ultra slim round profile LED lighting fixture with extruded polycarbonate , environmental friendly energy efficiebt ready to use pack with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 20 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Havells Cat Part No. LHEXAYP7PN6K020 or equivalent in /CG/Surya / Philips

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed .

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying XLPE LT heavy duty UG Cable of size 10 Sqmm 2 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed. Make :- Polycab / Havells / RR Kabel / Gloster

S & F GI Tubing light grade of size 40mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia connected to main earthing lead from earth electrode to test point upto 7.5 metre drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I.

S&F in repairs 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 50 mm Outer dia, ISI marked, SDR 7.4, PN 16 and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S&F in repairs 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 32mm Outer dia, ISI marked, SDR 7.4 , PN 16 and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S&F in repairs PP-R Gate Valves (Brass Insert) 32mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed.

S&F in repairs PP-R Gate Valves (Brass Insert) 50 mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed.

Making connection of PP-R distribution branch with PP-R main of 63 mm size by providing and fixing tee of 63 mm x 50 mm including cutting and making fusion joint etc all as specified and directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Markson (BID ID -3384703)

M/S RANA ENGINEERING ENTERPRISE (BID ID -3380918)