SPECIAL REPAIR TO MNS OFFRS MESS AT ROORKEE AND SPL REPAIR TO MT SHED (BLDG NO T-9) SUPPLY DEPOT ASC ROORKEE UNDER GE ROORKEE

Amount

Demolition of concrete (Un-reinforced) including kota stone slabs etc in ground floor and paving etc in exec 15 cm Thick below or above GL complete all as specified and directed.

Demolition of concrete in roofs, floor (other than ground floor), chajjas and other similar suspended work complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in coping/ kerbs/stops rounded or chamfered on edges etc complete all as specified and directed.

M&L 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base etc.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20 mm graded aggregate) as in plinth protection, floor etc, finished even and smooth without using extra cement complete all as specified and directed .

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) not exc 1.5 Sqm each including necessary cutting holes and making good using PCC (1:2:4) Ty B-0 complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) exc 1.5 Sqm but n exc 4 Sqm each including necessary cutting holes and making good using PCC (1:2:4) Ty B-0 complete all as specified and directed .

S&F factory made Pressed steel frames of size (105mmX 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, holdfast etc., including filling with PCC 1:2:4 type B0 (12.5mm graded aggregate) in hollow portion before fixing and making good to disturbed brick work complete all as specified and directed.

S&F factory made Pressed steel frames of size (165mmX 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, holdfsat etc., including filling with PCC 1:2:4 type B0 (12.5mm graded aggregate) in hollow portion before fixing and making good to disturbed brick work complete all as specified and directed.

S&F Powder coated anodised aluminium frame for doors, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F, Powder Coated aluminium door shutters, having top rail of size 101.60mm x 44.50x2.50mm, Middle rail of size 101.60mm x44.50x2.0mm , bottom rail of size 150.00mmx44.50x2.20mm and side vertical rail of size 83.50mmx44.50x1.80mm aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, 2 Nos powder coated handles 200mm long in each door,250mm long powder coated tower bolt, hinges, anodised aluminium snap beading screws, mortice lock etc complete all as specified and directed.

S&F sheet glass 5.5 mm thick ordinary quality and glazing with neoprene beading to aluminium frame complete exc 0.5 sqm in each pane complete all as specified and directed.

M&L 18mm Pre-laminated particle board, interior grade, pre-laminated both side with decorative choice lamination & other side balancing white lamination, sliding type/ fixed type with screws to timber/aluminium frame work complete all as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of steel, other parts made of mild steel heavy duty and fixed (Make- 'SAMRAT' or equivalent suitable for door 60-80Kg.) complete all as specified and directed.

S&F factory made 30 mm thick flush shutters, solid core construction with block board core and plywood face panels, water proof/ weather proof type on both sides complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; wire gauzed to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing . The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed.

S&F 300mm, ordinary brass rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F Stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack/galvanised wire staple complete all as specified and directed. (ISI Marked) complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F 250 mm size of bolt Stainless Steel sliding door bolts fancy type with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of Stainless Steel complete all as specified and directed. (ISI Marked)

S & F 100 mm size of Stainless Steel hinges complete all as specified and directed. (ISI Marked)

S & F 200 mm size Stainless Steel tower bolts fancy type of extruded section and fixed to shutter complete all as specified and directed. (ISI Marked)

S & F 150 mm size Stainless Steel handles decorative type complete all as specified and directed Make: Locally available Ist class quality duly approved by Engr-in-Charge and GE.

S&F Factory Made Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Factory Made Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F 4mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed .

S&F in repairs 4 mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L for Udaipur green marble 12-14 mm thick (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side if required, including cutting chasing if required complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed .

M&L 25mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in sub floor and levelling coarse etc complete all as specified and directed .

M & L Ultra charged vitrified Ceramic Light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M & L for glazed ceramic colour joint free tiles in vertical surface size 450X 350X 7 mm/ 450x 300 x7mm/ 600x300mmx7mmthick as required set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM 1:4 complete all as specified and directed.

M & L for Non - skid Ceramic joint free colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed in CM 1:4 rubbing and mirror polishing complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed .

M&L for brick work in CM 1:6 using Sub class ‘B’ Bricks straight or curved on plan exc 6 m mean radius complete all as specified

Ditto all as per item No Above but half brick wall in cm 1:4 complete all as specified and directed .

Taking down cement plaster (including tiles where required) of any description on Brick walls including racking out Joints, hacking for key scrubbing down with water etc complete all as specified and directed .

M&L for rendering 15mm thick consisting of two coats, top layer 5 mm thick in CM 1:4 (mixed with WPC) over 10mm th layer in CM 1:6, on fair faces of brick work ( WPC shall be measured & paid separately) finished even & fair complete all as specified and directed .

Supply only Liquid water proofing compound

M&L for rendering 15 mm Thick in CM (1:6) on Brick surfaces, rendering is to be finished even and smooth (without using extra lime or cement) all as specified and directed.

M&L for complete removal of existing treatment on surfaces of walls/ceilings by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed.

M&L preparation of newly or old treated plastered surfaces of walls and finishing walls 2 coat of cement base paint over one coat of primer and over a coat of 2mm thick wall care putty complete all as specified and directed .

M&L preparation of newly or old treated plastered surfaces of walls applying with 2 coat of oil bound distemper over one coat of primer and over a coat of 2mm thick wall care putty complete all as specified and directed.

M&L preparation new steel surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed .

M&L for one coat of synthetic enamel paint including preparation of old wooden surface complete all as specified and directed .

Taking down asbestos (corrugated, semi-corrugated etc) sheets in roof covering.

M&L Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, including necessary cutting chases to bk work complete all as spfd & directed.

M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as spfd & directed.

Dismantling of wall/ceiling boards Asbestos plywood of any thickness including cover fillets all as specified and directed by Engr-in-charge.

Providing and fixing tiled false ceiling of designer tiles (high pressure steam Cured) of 4mm thickness (as per IS:14862) of size 595x595mm and any one of the design (Cascade or Electra or equivalent) in true horizontal level, suspended on inner locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grms, both side inclusive and black painted groove on all T webs) consisting of main “T” runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, 1200mm long spaced between main “T” at 600mm C/C to form a grid of 1200x600mm and secondly cross “T” of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of 1200x600mm panel to form grids of 600x600mm and wall angle 15x20x0.36mm and laying false ceiling tiles in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main “T”, bottom exposed width of 15mm of all “T” sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5 mm width, all complete at all heights as per directions of EIC. Make:- Everest / Armstrong / Gypsum India Ltd. complete all as specified and directed .

S & F in repairs of 25 mm dia steel complete fancy type CP curtain rod with and including steel type brackets, stops, of suitable size & side caps etc. complete all as specified and directed Make: Locally available Ist class quality duly approved by Engr-in-Charge and GE.

S&F for 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed .

Dismantling water tanks of 250 Ltr capacity and removing to store complete all as specified and directed .

M&L 250 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) incl 20mm PTMT ball valve (Ball valve make:- Prayag) hoisted and fixed in position all as specified in SSR Part I. complete all as specified and directed .

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed .

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed .

S&F 15mm bore GI steel tubing medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Ditto but 20mm bore complete all as specified and directed .

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

Ditto but 15mm bore complete all as specified and directed .

S&F in repair for Stop valves, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 15mm bore pipe complete all as specified and directed .

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15mm bore complete all as specified and directed .

S&F in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed .

S&F in repair PVC valve less, symphonic action type, flushing cistern 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle, flush pipe including brackets of complete all as specified and directed.

S&F in repair PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and directed.

S&F in repair for Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with white seat cover complete all as specified and directed .

S&F in repair vitreous china wash basin , white, Oval type, size 630x450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe fixing complete all as specified and directed .

S&F in repair Flush pipe of polyethylene of high density or PVC. 32 mm dia, complete all as specified and directed .

M & L Concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested; in for150 mm bore pipe complete all as specified and directed .

M&L for Salt-glazed stoneware drain pipes laid in trenches and jointed as specified for 150mm bore pipe complete all as specified and directed .

S & F 100 dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) in repair complete all as specified and directed .

Ditto but nahani trap in repair complete all as specified and directed .

M&L PVC (SWR) pipes, single socketed, in any length , with rubber rings 110mm dia in repair complete all as specified and directed .

Ditto but 75mm in repair complete all as specified and directed .

M&L 110mm PVC (SWR) WC connector with lip ring in repair complete all as specified and directed .

M&L 75mm bore PVC (SWR) bends any radius in repair complete all as specified and directed .

- Ditto - but 110mm bore in repair complete all as specified and directed .

S&F 110 mm bore PVC (SWR) junction single,(Single T) equal or unequal in repair complete all as specified and directed .

M&L PVC (SWR) vent cowl 75mm bore in repair complete all as specified and directed .

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges in repair complete all as specified and directed .

M&L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm bore complete all as specified and directed .

M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick work complete all as specified and directed .

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and directed .

M & L Plain cement concrete(1:4:8) Ty D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed .

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed .

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed .

S &F chromium plated fancy type 15mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair. Complete all as specified and directed .

S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. Make JAQUAR ' AHS-CHR-155', CERA (F5006110) or equivalent in repair.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long Complete all as specified and directed

S&F in repair Vitreous China squatting plate urinal complete all as specified and directed .

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed .

S&F in repair Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed .

S&F in repairs sinks made of stainless steel 01 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed .

S&F in repairs sinks with drainage board made of stainless steel 01 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed .

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed .

M&L for rolled mild steel Joist, channel, angle, tubes or tee sections, fixed independently, without connecting plates, etc. Fe-410-W (Gde E-250) complete all as specified and directed.

M&L for cutting holes exe half brick but n exc one brick in brick walls in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings.

Material and Labour Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with 'J' bolt screws as specified

Material and Labour Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge etc fixed with 'J' bolt as specified

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint complete all as specified and as directed.

M&L for 40 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) finished surfaces even and smooth complete all as specified and directed.

M&L for 38mm wide glass dividing strips, 3mm thick, inserted in position, conform to design complete all as specified and directed.

M&L for one coats of cement based paint on external wall old surface including preparation of plastered surface all as specified and directed

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete.

M&L for brick work with old size sub class 'B' class bricks , straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed

Taking down cement plaster any description on brick or stone walls, /RCC walls surfaces etc. including raking out joints, hacking for key, scrubbing down wih water, etc .

M&L for rendering 15mm thick in CM 1:6 on brick walls finished over and fair without using extra cement complete all as specified and directed

M & L for new plastered surface on walls and applying two coats cement based paint over one coat of alkali resistant priming paint complete.( Make : Snowsem/Durocem/Crimocem)

S&F rolled mild steel in joist, channel, angle or tee sections fixed independently , without connecting plates etc quality conforming to Fe 410 W (Gde E-50 quality A) complete as specified and directed by Engr-in-Charge

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Material & Labour for Point Wiring modular type for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLS) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLS) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) including modular metal flush box made of GI sheet and modular white frame plate with cover complete all as specified and directed for the following. Note: ModularFlush box and modular frame plate & cover plate should be of same make all as approved for switches/sockets. (a) One light/fan/bell/exhaust fan point controlled by one, one-way modular switch 5/6 Amp complete all specified and directed.

(b) One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way modular switch complete all specified and directed.

(c) One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way modular switch complete all specified and directed .

All as per item No 122.01 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated FRLS but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm FRLS cable as earthwire complete all specified and directed.

S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S & F switch Modular single pole, one way 10 Amps , 1 module, 230 volts, 50 hz all as specified and directed. Make: Anchor Roma Cat no 66101S, Havells Crabtree Cat No ACWSXXW101 and CONA cat part No 14001

Supply and fix Modular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz all as specified and directed. Make: Anchor Roma Cat No 66407S, Havells Crabtree Cat No ACWKPXW063 and Cona Cat No 14061

Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 hz white/ivory finish all as specified and directed. Make: Anchor Roma Cat No 66104S, Havells Crabtree Cat No ACWSXIW161 and CONA cat no 14016

Supply and fix Modular Socket outlet, 10/16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz all as specified and directed. Make: Anchor Roma Cat No 66405S, Havells Crabtree Cat No ACWKCXW253 and CONA Cat No 14171

S & F bell push Modular single pole, one way 6 Amps , 1 module, ISI marked, 230 volts, 50 hz all as specified and directed. Make: Anchor Roma Cat No 66103S, Havells Crabtree Cat No ACWSBXW101and CONA cat no 14011

S&F bell ding dong elelctric 230V AC single pole all as speccified and directed.

S&F fan regulator modular type ,120 watt, 2 module complete all as specified and directed. Make: Anchor Roma Cat No 66503S, Havells Crabtree Cat No ACWRFHW008 and CONA cat 14086

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting complete all as specified & directed.

S & F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for "B-22 type to fix on batten holder complete all as specified and directed.

M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as speccified and directed

Supply and fix in replacement of modular MCB protected plug top and socket board in sheet steel enclosure with 25 Amp rated mini MCB and 25 Amp rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board including taking down existing unserviceable plug & socket board of any description and making good with cement plaster, putty and paint to match with the existing surfacecomplete all as specified and directed .

S&F in replacement and testing TP&N vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DBs with copper bus bar not less than 160 Amp for each phase with two neutral bar & two earthbar and cable lies for cable management for provision of MCCB 100 Amps ICs= 100% ICu, 16 KA four pole as incomer including connecting terminal strip complete and SP MCBs as outgoing complete pre-wired with suitable size copper conductor including taking out old unservicable DB and removing from site and making good of disturbed surface complete all as speciifed and directed.. Make: Hager VYV04DM-P, Schneider A9HVD04M and Legrand Cat part N0 507750

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with 100 Amps rated busbar, minimum ingress protection of IP40 all as specified and directed. Make: Legrand Cat part No 507611 , Hager Cat part No VYS08D and Schneider Cat Part No A9HSND08

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 4 way with 200 Amps rated busbar, minimum ingress protection of IP43 all as specified and directed. Make: Legrand Cat part No 507611 , Hager Cat part No VYS08D and Schneider Cat Part No A9HSND08

Supply & fixing MCB , SP, AC, 240 volts of 05 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. Note: MCBs should be of same make as of DB 8 way

Supply & fixing MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. Note: MCBs should be of same make as of VTPN 4 way and DB 8 way

Supply and fix in replacement of MCCB 100 Amp, 16 KA, TPN, 'B' curve, 415 V, 50 Hz including taking down existing unserviceable MCCB of any description complete all as specified and directed. Note: MCCB should be of same make as of VTPN 4 way

S&F LED tube light batten 20 watts 4 fts extruded aluminuim housing, translucent diffuser with LED light source , minimum 2000 lumen, natural white ,surge protection range- 2KV, voltage protection range 120-280 VAC with intergrated driver and surge protection complete all as specified and directed. Make: Crompton Bright Linea CCS-100-20-65-HL2-DP-NHW, Wipro Cat Part No D552065 and Havells Lumiline Plus LUMILINE+BS20WLED830SPCSS

S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed. Havells cat Part No LUMILINEBS10WLED865SPCWH, Crompton Cat part No CCS-103-10-65-SL-DP-NWH and Wipro Cat Pat No D531065

Supply and fix in replacement of surface/recessed mounted LED panel light 2'x2' size, 36 watts, full white / warm white as per site requirement with electronic driver in CRCA sheet steel body with polycarbonate diffuser suitable for POP / Amstrong / grid false ceiling complete with all fixing accessories including making electrical connection with pvc insulated and pvc sheathed twisted two core wire of suitable size complete all as specified. Make :Eveready Masterlite HX LEDPLB03616, Havells Petal2X2PLR36WLED830S and Crompton Vector IV LCTLRF4-36-CDL

Supply and fix in replacement of old unserviceable LED Post Top Lantern/Gate Light light fitting 30/40 watt with LED as source light IP-65 protection & tranparent diffuser and fixing arrangement on new GI Pipe medium grade of dia 40 mm duly grouted on wall/brick pillar with the help of cement mortar including making electrical connection with pvc insulated and pvc sheathed twisted three core wire of size 1.0 sqmm complete all as specified and directed at site. Crompton cat Part No LPTO-40-CDL, Havells Cat Part No RUBYPT40WLED757PSYMTOPC and Wipro cat Part No LP06-351-XXX-57-XX

S&F in replacement LED bollard light 9/10 Watt LED as source light CDL/WW made out of pressure die cast powder coated housing with PC diffuser with LED as a source light height not less than 90 cm including making electrical connection and PCC 1:2:4 work for founation etc complete all as specified and directed including making electrical connection with pvc insulated and pvc sheathed twisted three core wire of size 1.0 sqmm complete all as specified and directed.

Supply and fix in replacement of 1100 old unservicable pvc insulated and pvc sheathed three core copper wire of size 6.0 sq mm for providing electrical connections complete all as specified and directed.

Supply and fix in replacement of 1100 old unservicable pvc insulated and pvc sheathed three core copper wire of size 1.0 sq mm for providing electrical connections for LED bollard light including connecting on DB/junction box complete all as specified and directed.

S & F in replacement Decorative wall light fitting with brushed nickel/ stainless steel base, made out of polycarbonate/glass diffuser suitable for and including 9 Watt WW/CDL LED Bulb fixed on wall and making electrical connection complete all as specified and directed. Make: Philips Glint Cat Part No. 58070, Havells Floretine Cat No LHFOAJE1TN1I060 and Wipro Cat Part No Beuhome 1H BW02

Taking down AC from existing location and shifting of split//window AC of any capacity 1.5/2 Ton and pumped down the refrigerant gas from the AC, if the gas is required to make the system serviceable at re location and to assemble with necessary cutting drilling and plywork as required and the same has been deemed to be included in this item. No extra payment has been made against the same.

Supply and fix in replacement PVC / DK Thermoplastic cable junction boxes IP 65 with metric knockouts for cable entry, weather proof suitable for outdoor installation for Gate light and Post top lantern, fixed on wall with screw & rawal plug and on GI Pipe wth suitable size MS clamp and Nut-bolts,washer of size outside dimension 170 x 170 x 105mm complete including one connector block three terminals and PVC cable gland 02 Nos for incoming and outgoing cables with provn of 01 nos single pole MCBs 10-32 amps inside the box including taking out/down existing unserviceable junction box of any description complete all as specified and directed at site. Make : Syntex model No-GSJB 1414 or any equivalent moden in Naptune/Hensel.

Supply and fix LED 30 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver,including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed.

Supply and fixing sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

Supply and fixing sub main wiring three single core 10 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS ) 1100Volts grade drawn in & including rigid PVC conduit 32mm dia or more medium grade concealed in wall along with two run of 10.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

Supply and fixing sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 2.5 Sq mm PVC insulated unsheathed copper conductor cable (FRLS ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

Taking down old unserviceable ceiling fan and supply and fix BLDC 1200mm sweep ceiling fan 5 star rating with blds, down rod and accessories 230 volts with air delivery and less than 210 cmm including making electrical connection upto ceiling rose complete all as specified and directed. Note: Old Ceiling fan to be deposited in MES store Yard

Taking down old Exhaust fan & S&F Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep, 900 RPM complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed . Note: Old Exhaust fan to be deposited in MES store Yard

Taking down old exhaust fan S&F Exhaust fan PVC body AC single phase 230/240 Volt of size 250 mm sweep, 900 RPM complete with louvers shutter including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed . Note: Old Exhaust fan to be deposited in MES store Yard

Taking down old electric water heater & Supply and fix in replacement electric water heater,storage type steel body with stainless steel inner tank and heating element upto 1.5/ 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hz complete with all accessories such as safety valve, thermostate, NRV, Hot and cold water connection pipe all as specified and directed. Note: Old Water heater to be deposited in MES store Yard

Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed,CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit(resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7.The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270 x 240 x 200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including light grade GI pipe of size 15 mm upto 7 mtr incl cutting and chases on wall and floor and aking good using PCC complete all as specified and directed. Note : - On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. (b) Rate quoted by contractor is inclusive of excation work for earthing and refilling the excavated soil around earth pit.

Dismantling & taking out old unserviceable LT UG cable & Supplying & laying in replacement of LT UG cable ( Conforming to IS 1554) ISI marked1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches / ducts / through HDPE pipe under roads of size 35 sqmm 4 core complete all as specifed and directed. Note;- The earth work shall be measured and paid sepretely under appropriate item of Sch A

S&F in replacement Bus-bar chamber factory made out door type made out of 3mm thick CRCA sheet with canopy of size 700mm x 450mm x 300mm pedestal type with 250 Amps rated insulated bus bar TPN system & with One No of MCCB 200 Amp 25 kA pole MCCB as incomer and provision for 04 Nos MCCBs outgoing complete including making PCC platform for floor mounted busbar chamber with 600 mm long angle iron legs complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

Supply and fix GI tubing light grade ISI marked of 50 mm bore dia complete all as specified and directed.

Taking up or down galvanised steel tubing and connections of any size and type complete all as directed for following sizes :- (a) 20mm bore

(b) 40 mm bore

Supply and fix or lay in trenches galvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in trenches complete all as specified and drected of the following bore. (a) 20mm bore

(b) 40 mm bore

Supply and fix galvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in floor fixed on wall and ceiling complete all as specified and drected of size 20 mm bore

Cutting existing steel tubing of size 50 mm for addition or alteration for water connection complete all as specified and directed.

Screwing existing steel tubing of size 50 mm for alterations or additions (or lengthening screw on pipe to form connector) and inserting Tee of size 50x40 mm or 50 x20 mm as per site requirement complete all ass pecified and directed.

Taking down existing unserviceable gate valve & Supply and Fix Gun metal gate valve, ISI marked, with iron wheel head screwed both ends for iron pipe, fixed in repairs complete of size 20 mm bore

KISHORE CHAND DINESH CHAND

sidh builders

M/S A.K GARG

RAJENDER CONSTRUCTION CO

M/S DABAS CONSTRUCTIONS

JBN CONSTRUCTION

VIJAY ENTERPRISES

Mahamaya Engineers Services

VARDHMAN CONSTRUCTION CO