ARC Work order for Erection & Maintenance work of HT/LT line & TC and OH XLPE, UG CABLE Work on ARC Basis for work under ND and any scheme under MOLVAN and any S/dn under Kim Division Through outsourced agency for existing DGVCL Network for SDN under Kim Division.

Item Code Description Unit

Labour charge for excavation of cable

trench of 400mm width x 1200mm

depth, in any type of soil for laying of

1 9925000001 cable of size up to 240 mm2 (For Meter

additional cable 200 mm additional width

shall be considered i.e. half trench length

is to be considered)

Labour charge for excavation of cable

trench of 600mm width x 1200mm

depth, in any type of soil for laying of

2 9925000002 cable of size up to 240 mm2 (For Meter

additional cable 200 mm additional width

shall be considered i.e. half trench length

is to be considered)

Labour charge for excavation of cable

trench of 400mm width x 1500mm

depth, in any type of soil for laying of

3 9925000003 cable of size up to 240 mm2 (For Meter

additional cable 200 mm additional width

shall be considered i.e. half trench length

is to be considered)

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Labour charge for laying of 11kV / 22 kV

XLPE Cable of size up to 240 mm2 &

preparation of sand layer 100mm thick, in

the cable trench & covering the cable

with 150 mm dia (Inner), thickness

mm, 1.0 meter long RCC half round

muffs and providing and fixing of 4inch

width yellow colour polyethylene tape

with printing "CAUTION ELECTRIC

CABLE BELOW" at 0.75 m depth from

ground surface after laying cable in

trench. This will provide indication that

electric cable is passing underground so

as to protect cable from mechnical

injuries, refilling the same, as per

Instruction of Engineer in Charge (EIC).

Labour charge for horizontal drilling

using Auger machine without damage

to surface road at max 2.0 mtrs depth &

putting of 6.11 kg/cm2 , class-4,Green

color, 110mm O.D. , 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984-

1987(3rd revision) and BIS certification

and laying of 11KV/22KV XLPE cable of

size up to 240 mm2 in HDPE pipe, as

per Site Condition (excluding cost of

pipe). The detail map obtained from HDD

machine and excell sheet(hard and soft

copy) indicating the respective depth and

distance from adjacent landmark for each

segment for HDD is must required to be

submitted. HDD to be carried out at

depth 1.5 mtrs to 2.0 mtrs as per site

conditions and as per instruction of EIC.

Labour charge for horizontal drilling

manually without damage to surface

road at max 2.0 mtrs depth & putting of

6.11 kg/cm2 , class-4,Green color,

110mm O.D. , 8.5mm thickness H.D.P.E.

pipe confirms to IS 4984-1987(3rd

revision) and BIS certification and laying

of 11KV/22KV XLPE cable of size up to

6 9925000006 240 mm2 size, as per Site Condition Meter

(excluding cost of pipe). The detail map

and excell sheet(hard and soft copy)

indicating the respective depth and

distance from adjacent landmark for each

segment of cable to be submitted. Drilling

to be carried out at depth Minimum

mtrs to 2.0 mtrs as per site conditions as

per instruction of EIC.

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Supply of 6.11kg/cm2 , class-4,Green

color, 110mm O.D. , 8.5 mm

thickness H.D.P.E. pipe confirms to IS

7 9925000007 4984 and BIS certification for laying of Meter

underground 11KV / 22KV XLPE

cable up to 240 mm2 size.

Labour work for RCC concreting on

disputed location and repairing of

damage portion of road crossing for the

work carried out for roads crossing as

well as concreting & muffing of

ploes including all materials (1:2:4)

Providing & fixing concrete stone route

marker of 300 mm width x 150 mm

thick x 650 mm height embedded in

earth at least 300 mm below & 350 mm

above ground level respectively at

distance approx 50 meters along the

length of cable. The RCC concreting

(1:2:4)(all necessary maeterials will be in

bidder's scope) of route marker is to be

carried out 300 mm width x 150 mm thick

9 9925000009 x 300 mm below ground level as per No.

instruction of EIC. The route marker

should be with name of company with

approved yellow colour-DGVCL. The

distance from marker to cable and cable

depth with feeder name etc., marked with

arrow sign is to be painted on it.The route

marker is to be fixed at location near to

any fixed permanent location (not

necessary to fix exact on top of cable) as

per instruction of EIC.

Erection of D.P. (double pole) structure

using 9 / 11 Mtr. RSJ pole with cable

connection arrangement along with fitting

10 9925000010 of necessary fabrication for 11KV cable No.

including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive

of concreting & muffing of poles)

Erection of Single pole structure using

9 / 11 Mtr RSJ pole with cable

connection arrangement along with fitting

ofnecessary fabrication for 11KV/22 KV

cable including excavation of pit &

refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Erection of D.P. (double pole) structure

using 8.0 Mtr. PSC pole with cable

connection arrangement along with fitting

12 9925000012 of necessary fabrication for 11KV cable No.

including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive

of concreting & muffing of poles)

Erection of Single pole structure using

8.0 Mtr PSC pole with cable connection

arrangement along with fitting

ofnecessary fabrication for 11KV/22 KV

cable including excavation of pit &

refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of

Labour charge for erecting of 11kV /

kV XLPE cable of size up to

14 9925000014 mm on DP Structure with fixing of 02 Per Job

Nos polymer cleats on top and middle

part.Polymer cleats, nut bolts etc. fixing

material to be provided by contractor.

Providing & fixing of 6.11kg/cm2 , class-

4,Green color, 110mm O.D. , 8.5mm

thickness H.D.P.E. pipe confirms to IS

4984 and BIS certification on the

erected DP structure for the mechanical

protection of cable by inserting the cable

inside HDPE pipe. The HDPE pipe shall

be erected in such a way that 300mm

shall be below the ground level and the

rest 2700 mm shall be supported

on the DP Structure with 01 No

Polymer cleat.All materials including

polymer cleat and Nut bolt to be

provided by contractor.

Providing and fixing of pipe type

earthing from 80 mm dia class-B GI pipe

with pit to be filled with salt & coke and

construction of chamber as per DGVCL

16 9925000016 Drg. No. dg /100 for DP and cable. The No.

earthing pit should be joined with cable

by G.I. strip of size 1” width & 2 mm

thick. All material GI pipe, Coke, Salt etc

will be supplied by bidder.

Supply & fixing of heat shrink type

end terminations (outdoor) for upto

11kV 3C x 185 mm2 size XLPE cable as

per DGVCL technical specification

Supply & fixing of heat & shrinkable end

terminations (outdoor) for upto

kV 3C x 185 mm2 size XLPE cable as

per DGVCL technical specification)

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Supply & fixing of heat shrink type end

terminations (indoor) for upto 11kV 3C

x 185 mm2 size XLPE cable as per

DGVCL technical specification)

Supply & fixing of heat & shrinkable end

terminations (indoor) for upto

kV 3C x 185 mm2 size XLPE cable as

per DGVCL technical specification

Supply & fixing of heat

shrinkable straight through joint for

21 9925000021 upto 11kV 3C x 185 mm2 size XLPE No.

cableas per DGVCL technical

Supply & fixing of heat

shrinkable straight through joint type

for upto 22kV 3C x 185 mm2 size

XLPE cable as per DGVCL technical

Labour charge for excavation of

2100mm long x 1200mm wide x

mm deep joint pits for installation of

11kV / 22kV Straight through joints as

per instruction of engineer-in-charge &

covering the cable with 150 mm

dia (Outer), thickness 25 mm,

meter long RCC half round muffs &

refilling same as per instruction of

Providing and fixing of insulating bus

bar, made from 11KV/22KV XLPE cable

after removal of semi conducting layer

and applying of PVC heat shrinkable

anti-tracking core insulating tubing

(1.1KV), on both end terminal using

Aluminium long barrel heavy duty up to

240 sq mm lugs, Aluminium bus

connector. Taping with PG- clamp for bus

conductor as per drawing and as per

instruction of EIC. The Alluminium lugs

and PG clamp shall be covered with

11KV/22KV HT insulating tapes.

(11KV/22KV XLPE cable will be in scope

of DGVCL while all other materials will be

in bidder's scope)

Testing of cable at various points and

commissioning the feeder as per

25 9925000025 instruction of engineer-in-charge.Test No.

result shall be submitted by contractor

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Preparation and submission of 6 (six)

copies, of complete layout drawings

with GIS mapping as per actual cable

routing showing road crossing, HDPE

pipe sleeving, jointing locations, markers

Providing and fixing of Sign Board at

junction point Made out of 2 mm

aluminium sheet size 750x300 mm (2.5 x

1ft) rectangle, as per design, pre treated

with phosphate process and acid etching

coated with one coat of epoxy primer and

two coats of best quality paints,

refloctrorised with Hi-Intensity retro –

reflective sheeting as per the latest and

27 9925000027 frame fabricated from suitable size iron No.

angle. The Sign Board is to be fixed on

the base prepared from channel and

bracing angles which is grouted by

means of cement concreting of 1:2:4 for

size of 300 mm dia x 800 mm height (500

mm to be grouted in ground). The details

to be displayed on sign board will be

given by In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board

(Danger Board) on Distribution

Transformer Centers

Made out of 2mm aluminium sheet size

300x300mm (1x1ft) as per design, pre

treated with phosphate process and acid

etching coated with one coat of epoxy

28 9925000028 primer and two coats of best quality No.

paints, refloctrorised with Hi-Intensity

retro-reflective sheeting as per the latest

and frame fabricated from suitable size

iron angle. The Sign Board (Danger

Board is to be fixed at the location as per

instruction of In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of

size 250 mm (L) x 75 mm (W) from 3 mm

aluminium sheet along with 1.0 mm dia

aluminium binding wire for fixing of

aluminium tag near end termination joint

at DP structure for identifyng the cable.

The details of feeder i.e. 11 / 22 KV with

feeder name shound be punched on the

tag by letter punch of size 16 mm as per

instruction of In-charge Engineer.

Supply & fixing of heat shrink type end

terminations (outdoor) for 11kV 3C x

240 mm2 size XLPE cable as per

DGVCL technical specification

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Supply & fixing of heat & shrinkable end

terminations (outdoor) for 22 kV 3C x

240 mm2 size XLPE cable as per

DGVCL technical specification)

Supply & fixing of heat shrink type end

terminations (indoor) for 11kV 3C x

240 mm2 size XLPE cable as per

DGVCL technical specification)

Supply & fixing of heat & shrinkable end

terminations (indoor) for 22 kV 3C x

240 mm2 size XLPE cable as per

DGVCL technical specification

Supply & fixing of heat

shrinkable straight through

34 9925000034 joint for 11kV 3C x 240 mm2 size XLPE No.

cableas per DGVCL technical

Supply & fixing of heat

shrinkable straight through joint type

35 9925000035 for 22kV 3C x 240 mm2 size XLPE cable No.

as per DGVCL technical specification

Installation, Testing and

commissioning of 11 KV,630 A SCADA

Compatible, RRL type- 3 Way

36 9925000038 RMU including Two numbers of No.

earthings as per Drawing (material is in

bidder's scope) and as per DGVCL

Technical specification.

Installation, Testing and

commissioning of 11 KV,630 A SCADA

Compatible, RRLL type- 4 Way

37 9925000039 RMU including Two numbers of No.

earthings as per Drawing (material is in

bidder's scope) and as per DGVCL

Technical specification.

Installation, Testing and

commissioning of 22KV,630 A SCADA

Compatible, RRL type-3 Way,

38 9925000040 RMU including Two numbers of earthings No.

as per Drawing (material is in bidder's

scope) and as per DGVCL Technical

Installation, Testing and

commissioning of 22KV,630 A SCADA

Compatible, RRLL type-4 Way,

39 9925000041 RMU including Two numbers of earthings No.

as per Drawing (material is in bidder's

scope) and as per DGVCL Technical

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Construction of plinth for 11KV, RRL

type- 3 Way (i.e Two numbers of Isolator

& One number of Breaker) Ring Main

40 9925000042 Unit as per DGVCL's technical No.

specification mentioned in drawing no:

Drg. 11kv-01. All required material will be

supplied by contractor.

Construction of plinth for 11KV, RRLL

type- 4 Way (i.e Two numbers of Isolator

& Two number of Breaker)Ring Main Unit

41 9925000043 as per DGVCL's technical specification No.

mentioned in drawing no:Drg. 11kv-02.All

required material will be supplied by

Construction of plinth for 22KV, RRL

type- 3 Way (i.e Two numbers of Isolator

& One number of Breaker) Ring Main

42 9925000044 Unit as per DGVCL's technical No.

specification mentioned in drawing no:

Drg. 22kv-01. All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRLL

type- 4 Way (i.e Two numbers of Isolator

& Two number of Breaker)Ring Main Unit

43 9925000045 as per DGVCL's technical specification No.

mentioned in drawing no:Drg. 22kv-02.All

required material will be supplied by

Modifications e.g.Providing and fixing of

Terminal protectors i.e. Re-use able boot

(HT Side 11/22KV, LT Side 1.1KV)

including 11/22 KV insulating taps and

L.T.(1.1 KV) insulating taps ,Busbar,

Tapping from Bus Bar (11/22 KV XLPE

cable) through P.G. Clamp for H.T.

Jumper to D.O. Fuse to bushings of

Transformer Center, providing & Fixing

of jumper and providing & fixing of Heat

Shrinkable Anti Tracking Core Insulating

Tubing (Insulation Level 11/22 KV) in

H.T. jumper , Clamping arrangement of

cable support frame on both side of

existing Over Head type Distribution

Transformer to utilize in Under Ground

cable network as per drawing & as per

instruction of Engineer incharge. All

live parts i.e. PG-Clamp, connections of

D.O.fuses, HT bushings etc . shall be

covered with fixinng of 11/22 KV HT

insulating tapes. ( 11/22 KV XLPE cable

will be in scope of DGVCL while all other

materials will be in bidder's scope ) .

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI

Letter No: DGVCLDOKI/0573/06/2026 Approved Date: 19-06-2026

Laying of any size of 11/ 22 KV XLPE

45 9925000047 /PILC Cable in redaymade trench or in

Supply of 150 mm dia (Inner), thickness

46 9925000064 25 mm, 1.0 meter long RCC half round No.

ESTIMATE PART-B

TOTAL ESTIMATED AMOUNT OF

SCHEDULE (PART A + PART B)

Note :- All Rates are

Excluding of GST.

1. DGVCL will provide key material like M.S. materials,ABC/Bare

conductors,PSC/RSJ Poles,Insulators,Fabricated materials etc. to the

2.All fabricated items shall be fabricated as per DGVCL approved

drawing and by welding rods confirming to the relevent ISI specification

and as directed by Engineer in charge.

3.Necessary electricity connection for fabrictated items shall be provided

by DGVCL on payment of required charge for connection & electricity bill

of the same shall be paid by the agency.

4.All the rates are inclusive of PF and Exclusive of GST applicable time Executive

5.All steel material are to be painted as below:

(a) Scrubbing of rusted surface properly before applying the paints on to

the RSJ poles & steel fabricated materials of RSJ/PSC poles is must Kim Ind Division

(b) Two coats of approved ISI mark red oxide (primer) is to be properly

painted for the RSJ poles & steel fabricated materials of RSJ/PSC poles.

(c) Two coats of approved ISI mark silver paint (i.e. triple mangoes or

equivalent quality silver paint) is to be properly painted on to the RSJ

poles & steel fabricated materials of RSJ/PSC poles.

5. Qualified bidder has to work UG cable as well as erection &

maintenance (HT, LT & TC) work both as per sub work order given by

File No: DGVCLDOKI/TEN/e-file/6817/2026/3151/Account

Approved By: Executive Engineer,Technical,DGVCLDOKI