RETENDER OF PGP-252-25 CONSTRUCTION OF OPEN WELL AT KALIKKADAVU PANCHAYATH GROUND IN PILICODE GP 2024-25

Amount

Welll Digging

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

OD360300/2024-2025:Earth work in excavation by mechanical means (Hydraulic excavator/manual means) over arreas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan lift 1.5m to 3.0m

OD360294/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 3.m to 4.5m

OD360299/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 4.5m to 6.0 m

OD360301/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 6.0 m to 7.50 m

OD360296/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 7.50 m to 9.0 m

OD360298/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 9.0 .m to 10.50m

OD360297/2024-2025:Earth work in excavation by mechanical means (hydraulic excavator/manual means) over areas exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan lift 10.50 .m to 12.0m

5.7:Reinforced cement concrete work in well - steining excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.9.12:Centering and shuttering including strutting, etc. and removal of form for:Well steining

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD360302/2024-2025:Laterite dry stone masonry with neatly dressed stone of size 35x20x20 cm or nearest size for well lining including cost and conveyance of all materials and all labour charges etc complete.

OD360295/2024-2025:Laterite masonry with neatly dressed stone of size 35x20x20 cm or nearest size in cement mortar 1:6 for well lining including cost and conveyance of all materials and all labour charges etc complete (MOD 50.6.7.1 of DAR with additional labour for dressing and lifting)

OD360303/2024-2025:Laterite masonry with neatly dressed laterite stone of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc complete

OD407789/2024-2025:Laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

9.48.1:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.7.2:12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

13.71:Lettering with black Japan pint of approved brand and manufacture

12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Pipeline

50.18.9.15.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10Kgf/cm2- External work- Exposed on wall

50.18.9.4.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.32 mm dia 10.Kgf/cm2

18.17.4:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

SAKKEER HUSSAIN P M (BID ID -2139518)

Bidder Name

KHALANDER SHAFI B

SAKKEER HUSSAIN P M