SPECIAL REPAIRS TO BLDG P602 (DOUBLE STOREY) AT AHMEDABAD

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground level) complete.

Taking down chowkats or frames with shutter (W/out taking off shutters) exc 1.5 Sqm but n.exc 4 sqm each complete.

Taking down chowkats or frames with shutter (W/out taking off shutters) not exceeding 1.5 Sqm each complete.

S&F Solid PVC Door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforce with M.S square tube, high strength suppling & fixing in opening as per specification complete

S&F Factory made solid panel PVC door /cupboard shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, in the frame at site as per specification & drawing complete.

S&F factory made 30 mm thick Factory made flush shutter , Solid core , construction with board core and plywood face panels commercial type on both sides complete.

M&L for Second class hardwood Glazed and skeleton shutters 35 mm thick glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I section 8 clause 8023 (a), in II nd class hard wood complete.

S&F 150mm size extruded aluminium alloy handles fabricated type anodised complete.

S&F 150mm extruded aluminium alloy tower bolts extruted sections anodised complete.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring of size 150 mm complete

S&F 150 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete

S&F 150mm size Hasp and staples, safety type, Aluminium anodised with mild steel hinge pin including bolt plate and fixed with screws complete.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete

S&F mild steel Gde Fe 410-O or Fe 310-O Chowkhats and frames of door shutters ( any type, size etc.) of angle, Tee or any section with MS plates/ gusset plates, cleats, hold fast etc including fixing (except provision thereof) of hinges by welding complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete

M&L PCC type C1 Mix 1:3:6 (20mm graded stone aggregate), 75mm thick in plinth protection / path finishing the surface even and smooth without using extra cement with joints filled with bitumen grade 85/ 25 and sand in equal proportions by weight complete.

S&F Glazed ceramic tiles in vertical surface 450X350X7mm thick as in dados and skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick in CM 1:4, complete.

M&L Vitrified light shade Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and including screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors complete.

All as per item no 46 above but in vertical surfaces such as skirting over and including 10 mm thick backing coat in cement mortar 1:4 complete.

M&L for non skid ceramic (colored) tiles 7 to 8 mm thick as in floor area of each tile exceeding 0.06 Sqm but n exceeding 0 .11 Sqm, set and jointed in neat cement slurry and pointed in white or colored cement to match over and including screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors complete.

M&L for pre-polished kota stone slab 20-25mm thick as in shelves including cutting groves in wall making good disturbed surface, matching with existing surface etc; rubbing and polishing complete

M&L for machine cut kota stone slab 20-25mm thick as flooring/ landing laid and jointed with grey cement slury incl rubbing and polishing , over and including 20 mm thick CM 1:6 screed bed complete. (Note: All exposed side of kota stone slab to be rounded)

M&L for machine cut kota stone slab 20-25mm thick as in riser of steps, skirting, dado laid jointed with grey cement slurry f incl rubbing and polishing , over and including 10 mm thick CM 1:4 screed bed complete. (Note: All exposed side of kota stone slab to be rounded)

Taking down cement plaster on brick or stone walls, concrete walls etc incl raking out joints, hacking for key, scrubbing down with water etc. complete

M&L for Rendering on other than fair faces of brick work 10 mm thick in CM 1:6 first layer and second top layer of 05 mm thick in CM (1:4) mixed with water proofing compound in top @ 3% by weight of cement or as per manufacturers instructions on fair faces of first layer & finishing the surfaces even & smooth without using extra cement complete. (WPC measured and paid separately)

M&L, Rendering 15 mm thick on fair faces of brick work or concrete surfaces with in CM 1:6 is to be finished even & smooth (without using extra cement) wall complete

M&L for 10mm thick rendering in CM 1:3 finished even and smooth without using extra cement on ceiling, chajja etc complete .

M&L white washing three coats to ceiling surfaces including preparation of new plastered untreated surfaces complete.

M&L for preparation of new plastered surfaces on walls and applying two coats of oil bound distember with one coat of wall care putty complete.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement based paint on over one coat of primer on walls complete

M&L for complete removal of existing treatment and applying two coats cement based paint on over one coat of primer on walls complete

M&L for complete removal of existing treatment and applying two coats of Oil bound distemper and one coat of wall care putty on old plastered and unplastered surfaces on walls complete

M&L for complete removal of existing treatment and applying three coats of white washing to ceiling surfaces complete

S&F powder coated anodised Aluminium alloy sections sliding windows with frames Series-B (18 mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete. Note : Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle with or without opening for AC complete

S&F powder coated anodised Aluminium aloy sections windows with frames Series-B (18mm), side Hung shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass panes 4.80 mm nominal thickness or with stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete.

S&F powder coated anodised aluminum Ventilators with fixed aluminium frame of size 65x40x1.98 mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4 mm thick pin head glass and remaining portion to be louvered using 4 mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm incl necessary channel frame work, incl rubber gasket and aluminium beading complete.

M&L for preparation of new steel & iron surfaces of any description, over 10 cm with or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete

M&L for preparation of new wood and wood based surfaces of any description exc 10 cm with or girth with two coats of synthetic enamel paint over a coat of pink primer complete

S&F in repairs 15mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S&F in repairs 15mm PVC connection 600mm long with brass check nut on both sides screw to iron pipes complete.

S&F in repair for Stop valves 15 mm size, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repairs for 15 mm Bib taps, fancy type, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete

S&F in repair 15 mm swivel shower roses of PTMT incl fixing to steel pipe or union complete.

S&F in repairs 25 mm dia stainless steel fancy type drapary curtain rod with brackets and fancy type ends etc complete.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 10 ltr complete

S&F in repair vitreous china wash down water closet pan (Pedestal pattern) coloured including fixing bolt and plastic water closet seat black closed pattern with flat bottom cover with MS chromium plated hinging devices to matching colour complete.

S&F in repairs Vitreous China wash basin, flat back, size 550x400 mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed complete

S&F in repair 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm -210 gm) complete

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel heads screwed both ends for iron pipe complete.

S&F in repairs 1000 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete.

S&F in repairs PTMT square grating with waste hole 150mm size for trap in repairs complete

S&F Stainless Steel butt hinges 100mm size medium weight cold rolled mild steel complete

Taking down 15 mm dia GI tubing and connections, incl removal complete

Taking down 20 mm dia GI tubing and connections, incl removal complete

S&F 15 mm GI tubing medium grade with all fittings fixed to wall or ceiling or laid in floor complete

S&F 20 mm GI tubing medium grade with all fittings fixed to wall or ceiling or laid in floor complete

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm complete

S&F PVC (SWR) vent cowl 110mm complete

S&F PVC (SWR) branch piece 110mm single (double Y) equal or unequal with oval access door complete

S&F PVC(SWR) 75 mm dia soil waste and rainwater drainage pipes (6 kgf / sqcm) single socketed in any length with rubber ring joint laid in floor or fixed on wall complete.

S&F PVC (SWR) bends any radius 75mm with access door complete

S&F PVC (SWR) bends any radius 110mm with access door complete

M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate in roof etc as levelling coarse etc. complete

Taking down old damaged water proofing treatment from roof surface of any description incl broken out/ loose plaster/PCC (any thickness), scrubbing down with water etc. M&L APP based polymeric membrane minimum weighing 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid by torch application over one coat of bituminous primer @ 0.30 kg/sqm over and including 15 mm thick cement plaster in CM 1:4 including water proofing compound @2% by weight of cement, applying a coat of aluminium paint as per the makes approved by the Engr-in- charge including disposal of debries exe. 50 mtr and n.exe. 100 mtr from starting point complete.

M&L for providing precast cement concrete (1:2:4) type B-1 (20mm graded aggregate) as in manhole covers set in cement mortar (1:4) complete

M&L TMT bars 10mm dia and over cut to length bent to shape required in spacers and binders including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

M&L for Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is nor provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M&L for Providing and injecting Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry complete

M&L for provinding PCC 1:5:10 type E2 using 40 mm graded stone aggregate for filing in sunken floor complete

Supply only Integral water proofing compound

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping / conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

M&L for Point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm with 3 mm thick phenolic laminated white sheet cover for mounting of Piano Type switches, sockets, fan regulators for One light / Exhaust fan point controlled by one switch complete

All as per Item No 75 above but for One fan point controlled by one switch.

All as per Item No 75 above but for One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per Item No 75 above but for One socket outlet 6 amp controlled by one switch on indepdendent board.

All as per Item No 75 above but for One bell point controlled by one bell push.

All as per Item No 75 above but for one 16 amp socket outlet modular type for controlled by one switch on independent board using 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm complete.

S&F modular switch one way 6 amp 1 module complete

S&F modular switch one way 16 amp 1 module complete

S&F modular socket 6/16 - 2/3 pin combined 2 module complete

S&F modular socket 6 amp 2/3 pin combined 2 module complete

S&F Ceiling rose 6 amp, 3 plates polycarbonate body complete

S&F modular hum free electronic step fan regulator, 100 watt 2 module complete

S&F bell multi music type, AC, 240 volts complete.

S&F bell push, flush type, 6 amp 240 volts complete.

S&F angle holder, insulated polycarbonate body with back plate complete.

M&L in replacement submain wiring alongwith earth continuity conductor with PVC insulated FRLSH multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour 20 mm dia along with accessories of nominal sizes 2x6 sqmm + 1x6 sqmm earth continuity conductor complete.

S&F LED batten (1.2 m) made of Aluminium housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 100+ lumens per watt and total power consumption not less than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 & similar to Make : Philips cat no. ENDURALED BATTEN " BN 108C LED 20S PSU CDL WH " complete.

S&F LED fixture 8 watt including connection & similar to Philips LED LINEA cat ref no. BN 550 WLED 6 - 6500 complete.

S&F LED bulkhead fitting 12 watt 6500k, IP 66 & IK 09 with pressure diecast aluminum housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable & similar to code DA11265 of Wipro make (1100 lumen) complete.

S&F in replacement MCB SPN, 240 volts, 8 ways distribution board powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces complete

S&F in replacement MCB distribution board ETPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces complete.

M&L in replacement earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

S&F in replacement MCBs Single pole 6 to 16 amp as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs & similar to Make Legrand DX3 cat ref no. 408587 to 408592 complete

S&F in replacement MCBs Double pole 32 amp as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs & similar to Make Legrand DX3 cat ref no. 408636 complete

S&F in replacement MCBs Four pole 63 amp as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs & similar to Make Legrand DX3 cat ref no. 408702 complete

Taking down Ceiling Fan of any make, type and sweep by disconnecting Electric Connection and deposit to MES store.

M&L of ceiling fan recd from taking down any sweep any make, cleaning throughly, servicing of fan motor & parts fitted there in, oiling, greasing to bush / bearings, replacement of unserviceable parts if required, applying two coat of white synthetic enamel paint over one coat of primer on fan blades and body, re- assembling, testing hanging at site as directed.

S&F air ventilation fan 250 mm in toilet in rectangular in shape, PVC body, white colour 230Vwith louvers shutter complete.

S&F in repairs sheet metal enclouser single pole and neutral with a 2 pin and earth plug and socket 20 A 240V complete with one single pole MCB of capacity 20 A complete.

Supply, laying and testing of LT UG cable, XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 4 core complete.

Excavation in soft / loose soil in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out complete.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cms thick complete.

Removing surplus soil to a distance not exceeding 50 m and depositing at a level not exceeding 1.5 m above the starting point complete.

S&F steel tubes light grade galvanised with all fittings fixed to walls / floors / poles / road crossing etc of 40 mm bore complete.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete.

Supplying and laying old size bricks, common burnt clay building bricks sub class 'B' designation 75 laid in trenches over sand for cable protection complete.

Boring holes in soil for under reamed piles and getting out and disposal of spoil to a distance n exc. 50 m for a pipe of dia 40 mm in size complete.

chhaba construction

DMA PROJECTS

TECH SERVE SOLUTIONS