REPAIR MAINT OF BR WORKS IN WATER SUPPLY INSTALLATIONS AND EM INSTALLATIONS IN SEC A B AND C UNDER GE UTILITY AMBALA CANTT

Amount

Taking down cement or cement lime plaster of any description on brick or stone wall etc including racking out joints , hacking for key scrubbing down with water all as directed by Engr-in-Charge.

Demolition of brick work built in CM or cement lime mortar incl all quoins, arches , pillar,drain etc all as directed by Engr-in-Charge.

Demolition of cement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work , complete all as specified and directed.

Material and labour for brick work built in CM (1:6) straight or curved on plan exceeding 6 metre mean radius using sub class ‘B’ bricks (Old size bricks) complete all as specified and as directed.

Material and labour brick work built in CM (1:6) straight or curved on plan exceeding 6 metre mean radius using sub class ‘B’ bricks (Except bricks) complete all as specified and as directed.

Material and Labour formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (Horizontal or Sloping) for rough finished flat surfaces of concrete

Material and labour formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide for rough finished surfaces of concrete

Material and labour providing reinforced cement concrete 1:1.5:3 (Nominal mix) (using 20mm graded mechanically crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roof, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M&L PCC in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed type B1 (1:2:4) using 20 mm graded aggregate(If reinforced concrete, reinforcement should be measured separately )

Material and labour mild steel TMT bars, 8 mm dia and over , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L in repair Precast RCC louvres and jallies, Set in CM(1:4) 50mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed.

M&L PCC in sub base, foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block (50% grey and 50% coloured) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment over and including 50 mm sand cushion complete all as specified and directed.

M&L 15 mm thick rendering in CM 1:4 with water proofing compound @2% by weight of cement incl. finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid seperately) (Note: Use only Yamuna sand )

Material and labour 15mm thick rendering in cement mortar (1:6) on brick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:3 as in ceiling(use only Yamuna sand)finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of new plastered surfaces on ceiling and applying three coats of white wash etc complete all as specified and directed

Material and labour for preparation of new plastered surfaces and applying three coats of white wash on wall, complete all as specified and directed.

M&L preparation of new wall surfaces and applying two coats of cement base paint over a one coat of cement primer complete all as specified and directed.

Supply only integral water proofing compound.

Taking down shutter of any description exc 1 Sqm but n. exc 2 Sqm each and removing from site complete all as specified.

Taking down shutter of any description exc 2 Sqm but n. exc 4 Sqm each and removing from site complete all as specified.

Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), area not exceeding 1.5 Sqm each and removal from site including iron mongry, hold fasts etc. complete all as specified.

Taking down chowkats or frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each with shutters (without taking off shutters from frames), and removal from site including iron mongry, hold fasts etc., complete all as specified and as directed.

Supply and fixing for mild steel framed work as in door chowkats /gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides) and hanging also fastening and fixing complete all as specified.

S&F 2nd class hard wood small fittings such as bracket of any type, shaped door and window stops, latch and hinge block and the like, articles n. exc 200cu.cm each fixed in repairs complete all as specified.

Supply and fixed factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified.

Supply and fixed factory made 30 mm PVC rigid foam panel door shutter made from mild steel tubular frame of size 19 mm x 19 mm for stiles and 15 mm x 15 mm for top and bottom rails and covered with 5 mm thick head moulded PVC channel having width of 50 mm to form stiles and PVC street of width 75 mm to form rock rail, bottom rail and top rail or either side having panels inserted with 5 mm thick PVC sheet sealed with solvent cement adhesive to the stiles and rails with 5 mm x 25 mm PVC sheet beading on either side including 03 Nos.100 mm aluminium hinges,02 Nos 125 mm aluminium handle,02 Nos 150 mm aluminium tower bolt etc for each door complete all as per manufacturer instructions complete all as specified.

Supply and fix factory made shutter, 35 mm thick, 2nd class hardwood (Hollock) rail and style, plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified.

Material & Labour IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in SSR part-I section 8 clause 8.2(a) supplt and fixed to choukats complete all as specified and directed by Engineer-in-Charge at site.

Supply and fix steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable complete.Make : Manufactured by Ram Fabricators Pvt Ltd Panchkula (Hr.) or M/S TEE PEE Enterprises Ludhiana (PB). Note: (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery (iii) Glazing, wire mesh & painting grill shall be measured & paid for separately.

S&F MS steel ventilators of section framed fixed type and fixed wire mesh with flat bends 10mmX3mm with nut bolts complete all as specified.

Supply and fixing aluminium alloy anodized (powder-coated) door frame and shutters with hollow aluminium anodized sections as specified including aluminium alloy anodized snap type beads, dish type door handles, glazed clip joint cleats, rubber gasket, dead lock 4 levers, two numbers of aluminium alloy anodized tower bolts to each leaf etc. including fixing frame to wall/RCC members with rawl plugs complete. Sections of doors shall be aluminium hollow sections as follows : - (a) Door Frame single groove 101.6mmx44.45mmx2.15mm thick (b) Shutter top 47.62mmx44.45mmx1.95mm thick. (c) Shutter bottom 114.30mmx44.45mmx2.15mm thick (d) Shutter vertical 85mmx44.45mmx1.80mm thick (e) Shutter middle 83.5mmx44.45mmx2.40mm thick (f) Gauging clip weighing not less than 0.097kg/metre (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. and Glass pane shall be measured and paid separately.) .Manufacturersof section : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or any other equivalent approved by GE.

Supply and fixing aluminium alloy anodized (powder-coated) window frame with double shutters open able type, with aluminium sections as per of “Jindal” section numbers for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, aluminium anodized barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified for series-B “ Jindal” section numbers for casement (a)Frame of section 101.6mmx44.45mmx2.10mm thick and section for shutter 47.62x44.45x1.95 mm thick (b) Mullion 53mmx52mmx 2mm thick not less than 1.065 kg/mtr. (c) Glazing clip weighing 0.259kg/mtr. (d) Windows shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and one no per each open able leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. Glass pane and wire gauge shall be measured and paid for separately. Manufacturers : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or any other equivalent approved by GE.

Supply and fixing 6mm thick plain coloured bakelite sheet pre laminated both side with decorative choice lamination or acrylic boards for fixing in panels of aluminium doors, complete all as specified.

S&F Sheet glass 5.5mm thick, ordinary quality & glazing with oil putty in square but 0.5 sq.m in each pane

Supply and fixing hydraulically regulated door closer, aluminium body, design No.1 universal type suitable for shutter of weight more than 35Kg complete all as specified and directed. (Make : Sandhu, Universal, Everest)

Supply and fixing double action floor spring, hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet, foundation box, main body with steel cover governing pivot made of brass, parts made of mild steel, heavy duty, complete all as specified.Make -Sandhu/Smart/Everest

Repairing of aluminium door of any description area not exceeding 2.50 Square metre each by adjusting floor spring, replacing cover of floor spring and screws etc. including labour for replacement of floor spring, rubber packing, glass pan, bottom panel etc., complete all as specified. Note : Floor spring, glass pane, rubber packing, dead lock, handle panel of any type etc. will be measured and paid separately.

Supply and fixed aluminum anodized, barrel tower bolts with plate, staples and bolt of extruded section 200mm long, ISI marked, complete all as specified.

Supply and fixed mild steel butt hinges of 50mm length, cold rolled, medium weight, complete all as specified.

S&F Butt hinges 100mm size, extruded brass,with mild steel hinge pin, bright polished, type B-11complete all as specified.

S&F 250 mm Aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Supply and fixing aluminum handles, cast type, anodized 150mm long, complete all as specified.

S&F mild steel door spring of 150 mm size ordinary rat tail rod pattern spring including roller and roller plate ISI marked complete all as spd.

Supply and fixed galvanized mild steel wire cloth with 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified.

Supply and fixed (in repair) galvanized mild steel wire cloth with 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with finned tacks or galvanized wire staple complete all as specified.

Hacking out old broken glasses area exc 1.5 sqm, any thickness and in any position from wooden or metal frames fixed with oil putty or beads etc and removing from site, complete all as specified.

Supply and fixed sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified.

Material and Labour surface of wood and wood based material steel and iron work, new or old treating such as hold fast, etc, area tarred n. exc 0.1 sqm each and treated with coal tar or coal tar black paint, complete all as specified.

Providing plain cement concrete B-1 type (1:2:4) using 20 mm graded crushed stone aggregate as in fixing of hold fast, copings, bed plates, plinth courses and the like finished fair and even, including necessary form work complete all as specified

Material and Labour two coat of synthetic enamel painting to wood surface of any description, not otherwise described over 10 cm width or girth including preparation of new surfaces over a coat of pink primer, complete all as specified.

M&L two coats of synthetic enamel paint on steel surfaces over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified.

Mild steel work as in hold fast,clamp etc. complete all as specified.

Dismantling of Brick tiles or terracing tiles, single layer on roofs complete all as specified.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof complete all as specified and directed.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement & sand slurry 1:3

Material and labour 50mm thick plain cement concrete,1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in roof padding, lintel upto 1.5m span , copings,fillets,bed plates, plinth courses ,seismic bands and the like finished fair and even, including necessary form work complete all as specified.

Material and labour providing 3 mm thick APP(Atactic polypropylene polymer) modified prefabricated five layer, weight not less than 3.6 Kg/Sqm water proofing membrane, black finished, reinforced with Non-woven polyster matt make as approved over roof consisting of a coat of bitumen primer @ 0.40 Ltr/Sqm by same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25º C temperature and viscocity 70-160 Cps. over the primer coat of industrial bitumen 85/25 @1.2 ltr /kg, the layer membrane shall be using butane torch and sealing all joints etc. after preparing the surface complete as per standard practice as per manufactuter's instructions all as specified and directed. The vital physical and chemical parameters of the membrane shall be as under:- (i) Joint strength in longitudinal and transverse direction at 25º C as 650/450 N/5 Cms. (ii) Tear strength in longitudinal and transverse direction as 300/250N/5 Cms. Softening point of membrane not less than 150º C cold flexiblility up to 20º when tested in accordance with ASTM (D-5147) (iii) The laying of membrane shall be carried out through the manufacturer or their authorized applicator only.

Material and labour 40 mm thick brick tiles laid on and including 15 mm thick bedding layer in cement mortar 1:6 and joints grouted flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement, complete all as specified and directed and flush pointed in cement mortar (1:3), complete all as specified.

All as per ser item No. 61 here-in-above, but except tiles, complete all as specified.

M&L PCC in roof kerbs of mud stops, rounded or chamfered on edges type B1 (1:2:4) using 20 mm graded aggregate complete all as specified.

Disconnecting existing tanks(exc 250 and n.exc. 500 ltrs capacity), setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified.

Dismantling PVC (SWR) rain water pipes 110 mm dia complete all as specified.

PVC (SWR) pipes 110 mm single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F PVC (SWR) bends any radius 110mm dia

M/S M S BUILDER AND CONTRACTORS

Ashwani Kumar

M/s Guddu Builders

s.v.builders