SPECIAL REPAIR TO BUILDING NO. P-88 AND CERTAIN MINOR/REVENUE WORKS AT MILITARY STATION KOTA

Amount

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Dismantling cast iron work of any description, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring/sub base finished even and rough to receive floor finishes/screed, complete all as specified and directed.

M&L for jointfree non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L for applying 15 mm thick screed in CM 1:4 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

Supply only approved liquid water proofing compound, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 18.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 Sqm each, complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 Sqm and n. exc. 4.00 Sqm each, complete all as specified and directed.

Taking down shutters of any description n. exc. 1 Sqm each, complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

M&L for 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates or sliding track for sliding windows, including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.34 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable handle (1 No) and sliding lock device, complete all as specified and directed.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm cut to size required at site for fixing in aluminium window/ventilator/door shutters, complete all as specified and directed. (Note: Fixing cost of wire cloth shall be deemed included in the unit rates of aluminium shutters)

M&L mild steel framed work as in doors or gates of angles or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe-290 Grade-E-165, complete all as specified and directed.

Cutting holes into or through brick walls or stone masonry built in cement mortar for inserting holdfast etc and making good in CM 1:3 or cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate) depth exc. half brick and not exc. one brick complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 125 mm size aluminium handles, cast type, anodised, complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

S&F figured/pin head glass 3mm thick ordinary quality and glazing with oil putty in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F Wire netting of stainless steel wire 1.4 mm dia fixed with tinned tacks of wire staples, size of mesh 25 mm, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces, exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F in repair stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:4 including finishing the surface even and smooth, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 3 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceilings, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm bore pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm bore pipes with and including all new fittings complete all as specified and directed.

Cutting chases pinning in, making good to facing where required and pointing in CM (1:3) to ends of edges of landings, shelves, cills, lintels etc and making good cutting, girth not exc 10 cm, in brick walls, complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, chromium plated brass, fancy type, screwed down, high pressure, screwed for iron pipe or for unions, complete all as specified and directed.

S&F in repair 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in repair angular stop valve 15 mm nominal bore cast copper alloy, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle screwed one end for iron pipe or for union and fixed, complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling existing water tank, complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in repair 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in repairs PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed, complete all as specified and directed.

S&F 4 way diverter for concealed fitting with built in non return valve and diverter handle including taking out of old wall mixer, complete all as specified and directed.

S&F in repair stop valves 15 mm nominal dia, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair towel rack of stainless steel, size 600x250 mm, fixed with and including CP brass screws and wooden/plastic cleats, complete all as specified and directed.

S&F in repair 10 Ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC float, brackets including superior quality PVC flush pipe of 32 mm dia, complete all as specified and directed.

S&F in repair vitreous china wash hand basin with pedestal, white with flat back, size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets and one CP brass waste coupling, complete all as specified and directed.

S&F 15 mm bore CP brass centre hole basin mixer for mixing hot and cold water, screwed down for iron pipe and fixed, complete all as specified.

S&F in repair swivel shower rose of CP brass, 80 mm dia, for fixing with 15 mm pipe with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of CP brass, complete all as specified and directed.

S&F in repair 'D' type towel rail 60 cm long, stainless steel, fancy type, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

S&F circular towel ring made of stainless steel, 200 mm dia, fixed to PVC rawl plugs with SS screws, complete all as specified and directed.

S&F shelf of PTMT fixed with and including CP brass screws and wooden/PVC cleats (Minimum weight 300 gms), complete all as specified and directed.

S&F PVC connection, 15 mm size with two PTMT nuts, length of connection 450 mm, complete all as specified and directed.

S&F 100mm cast iron sanitary connection socket to fit WC out-let, complete all as specified and directed.

S&F 100 mm dia cast iron floor trap with stainless steel grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

M&L for 150 mm bore salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:1, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

M/L for 50mm thick rough dressed stone slabs for manhole covers n.exc 2 mtr in length, punched dressed on face and along exposed edges, self faced on other side and sets and pointed in cement mortar 1:4 complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L for laying fully vitrified paving tiles of size 300x300x20 mm thick suitable for exterior areas, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L precast (factory casted) cement concrete kerb stone casted in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with plain or interlocking joints (as directed), making groove in ground of desired dimension, placing in position and set and jointed in CM 1:4, making good disturbed surface of ground, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L for granite stone work, 20 mm thick, glazed (table rubbed and polished) fixed as in cooking plateform, steps, treads, risers, jambs, window cills etc and the like set in cement mortar 1:4 and pointed with white cement using marble dust with admixture of pigment to match the shade of stone, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of old painted surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 3 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for preparation of old previously decorated plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment from previously decorated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F in repair soap dish made of stainless steel, approx size 160x100 mmx25mm and 1 mm thick, fixed to walls with plugs & SS screws, complete all as specified and directed.

S&F in repair ABS body health faucet (Bidet spray) in chrome finish, including 15 mm dia chromium plated pop up connection pipe of minimum 1.00 m length with CP brass nuts, complete all as specified and directed.

S&F in repairs 15 mm dia two way fancy type bib cock, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed to iron pipe or brass ferrule, complete all as specified and directed

S&F salt glazed stone ware gully traps, square or round mouthed, type 'P', size 150x150 mm, with and including bedding in PCC 1:5:10 type E1 using 20 mm graded stone aggregate, complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

Labour only for rounding to edges of kota stone/marble stone/granite stone of 15 to 25 mm thickness by making stone bull nosed/rounded as in floor, steps, platform etc, complete all as specified and directed.

Demolition and breaking up drain pipes and fittings, salt glazed ware, AC or PVC, internal dia of pipe 100/110 mm, complete all as specified and directed.

Demolition and breaking up drain pipes and fittings, salt glazed ware, AC or PVC, internal dia of pipe 75/80 mm, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 100 mm dia, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 75 mm dia, jointed in CM and taking out from trenches if required, complete all as specified and directed.

S&F 100 mm bore cast iron pipe soil, waste & vent pipes, with or without ears, in any length, with cement joints, laid in trenches or under floors, complete all as specified and directed.

S&F 75 mm dia cast iron pipe soil, waste & vent pipes, with or without ears, in any length, with cement joints, laid in trenches or under floors, complete all as specified and directed.

S&F 75 mm dia cast iron pipe soil, waste & vent pipes, with or without ears, in any length, with cement joints, fixed to walls/ceiling, complete all as specified and directed.

S&F 75 mm dia cast iron pipe soil, waste & vent pipes, with or without ears, in any length, with cement joints, fixed to walls/ceiling, complete all as specified and directed.

S&F 100 mm dia CI bend (any radius), diminishing pieces or tapers (larger dia measured), with oval access door, complete all as specified and directed.

S&F 75 mm dia CI bend (any radius), diminishing pieces or tapers (larger dia measured), with oval access door, complete all as specified and directed.

S&F CI branch pieces 100 mm bore single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F CI branch pieces 75 mm bore single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F CI cowl 100 mm bore, fixed with cement joint, complete all as specified and directed.

S&F CI cowl 75 mm bore, fixed with cement joint, complete all as specified and directed.

S&F in repair vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

Dismantling wall and ceiling boards (plywood) or insulation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, complete all as specified and directed.

S&F 10 mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing, complete all as specified and directed.

M&L 12 to 15 mm thick marble as in shelves and the like, makrana white, table rubbed and polished, set in CM 1:4 and pointed in CM 1:2 using white cement and marble dust, complete all as specified and directed.

S&F in repairs 18 mm thick prelaminated MDF board, exterior grade (Grade I, type 2), both side off white shade or shade as approved by Engineer in Charge, fixed as in shutters, shelf and partition etc of kitchen cabinet, complete all as specified and directed.

S&F in repair stainless steel telescopic channel suitable for kitchen drawers, 450 mm long, complete all as specified and directed.

S&F in repair 150 mm size stainless steel handles, superior quality, bright or matt finish, complete all as specified and directed.

S&F in repairs auto close hinges made of stainless steel, bright finish, complete all as specified and directed.

S&F in repairs kitchen baskets made of stainless steel, size 435x510x100 mm, fitted to modular kitchen drawers, complete all as specified and directed.

S&F in repairs kitchen baskets made of stainless steel, size 435x510x150 mm, fitted to modular kitchen drawers, complete all as specified and directed.

S&F in repairs kitchen baskets made of stainless steel, size 435x510x200 mm, fitted to modular kitchen drawers, complete all as specified and directed.

S&F in repairs kitchen baskets made of stainless steel, size 520x500x150 mm, fitted to modular kitchen drawers, complete all as specified and directed.

S&F in repairs kitchen baskets made of stainless steel, size 150x500x430 mm, fitted to modular kitchen drawers, complete all as specified and directed.

M&L for roof tiles, Mangalore pattern, interlocking at side joints, laid dry, complete all as specified and directed.

Dismantling of corrugated or semi corrugated asbestos cement sheets in roof covering including ridges, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation in post holes (or similar holes) Each n exc 0.50 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance of n exc 50m and making good surface in soft/loose soil, complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete etc, complete all as specified and directed.

Supply, fabrication and fixing MS tubes, medium grade with connecting plates as in posts and struts including cutting to shape, provided with necessary nuts, bolts, washers, welding etc, complete all as specified and directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240, complete all as specified and directed.

S&F 16 to 20 mm dia MS screw bolts (Machine made ) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt exc 5 cm but not exc 15 cm long, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based plain steel sheet crimped eaves and steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

M&L moorum or red bajri filling in floors or pavings, hardstanding and in foundation etc, laid in layers not exc 30 cm thick, spread, leveled and rammed including watering, complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L Machine pressed precast conctete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

S&F 0.80 mm thick plain galvanised iron (Class VI) sheet in ridges, hips, valley, guttters etc, straight flashings (length and girth as fixed), complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to wall, ceiling or floors, complete all as specified and directed.

S&F PVC (SWR) 110 mm bore single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work new or old, like ends of posts, backs of chowkhats etc area exc 0.10 Sqm and n.exc. 0.50 Sqm and treating with tar or coal tar black paint, complete all as specified and directed.

S&F mortice lock, made of brass, vertical type, size 100 mm, mild steel, 4 levers, with duplicate keys, fitted to aluminium door shutters, complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel, heavy duty and fixed, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

Formwork (rough finished surfaces) to sides of concrete foundations, column footings, bases of columns, raft and raft beams, sides and soffits of plinth beams or other similar works, vertical or to batter for rough finished surfaces, complete all as specified and directed.

Formwork (rough finished surfaces) to sides of columns, pillars, piers, posts, struts and stanchions etc complete all as specified and directed.

Formwork (for fair finished surfaces) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

Formwork (rough finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exc 200 mm thick complete all as specified and directed.

Formwork (rough finished surfaces) to edges of concrete exc 10 Cm thick and not exc 20 Cm thick as in slabs, bands, cills, flooring etc for rough finished surfaces complete all as specified and directed.

Formwork (rough finished surfaces) Chhajja, chullah hoods, weather shades, corbels, water troughs and similar items including edges, complete all as specified and directed.

M&L mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L mild steel TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

~Ditto~ but 5 to 10 mm dia mild steel TMT bars as in stirrups, spacers and binders etc complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded crushed stone aggregate), as in columns, pillars, piers, posts and struts etc, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels etc, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landing balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate), as in chhajjas, facias etc, complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

S&F micro perforated square edge and attractive finish mineral fibre (sand micro of nominal size 595x595x5 mm thick having building attribute as in false ceiling, fixed with and including grid of size 600x600mm having main frame of aluminium T of size 35x25x0.50 mm thick, cross aluminium T of size 35x25x0.5 mm thick, the grid shall be suitable for mineral fibre tiles and hanging from soffits of existing RCC roof slab with using connecting clips, complete all as per manufacturer’s instructions, specified and directed.

M&L rendering 15 mm thick in CM 1:4 on fair faces of brick work of concrete surfaces with using liquid water proofing compound as per manufacturer's instructions, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. (Note : Liquid water proofing compound shall be measured and paid separately.)

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in- charge.

M&L preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including making good disturbed surface all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including making good disturbed surface, complete all as directed and specified.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, complete all as specified & directed.

S&F in replacement wall mounted LED Tube light fittings, batten type with bipin holders, powder coated steel with retrofit 18 watt LED tube, internally prewired, complete all as specified and directed.

S&F in replacement wall mounted LED Tube light fittings, batten type with integrated LED tube, powder coated steel with retrofit 11 watt LED tube, internally prewired, complete all as specified and directed.

S&F in replacement LED building security light fitting, 25 watt with high power LED as light source, pressure die cast aluminium housing with IP 66 deg of protection, complete with minimum 0.55m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 40 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 63 Amps, Triple Pole & Neutral, 415 Volt, 16 KA 'B' curve including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 4 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for items of submain wiring:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 25mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 100x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 175x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 200x150 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 250x200 mm and 50 mm deep, complete all as specified and directed.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

Supply, laying, connecting and testing cable PVC insulated armoured and XLPE PVC sheathed LT 1100 volts grade with aluminum conductor of size 25 Sqmm 3.5 core, including disconnecting and taking out existing cable, complete all as specified & directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

M&L 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

Disconnecting and taking down exhaust fan of any size and refixing the same after rewiring work, complete all as specified and directed.

S&F SPN enclosure with a two pin and earth plug and socket, complete with one double pole MCB of 20 amps, 230 Volts AC, complete all as specified and directed.

S&F metal body propeller type ventilating fans (Exhaust fan), 240 volts AC, 300 mm sweep with louver shutter complete including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

S&F LED light fitting 36 Watt, 230 Volt AC, recessed mounting mirror optic luminiare with paralite louver complete, suitable for false/grid ceiling, complete with electronic driver, connector block and all accessories, duly prewired, including connecting up with three core twisted flexible copper conductor cable of size 14/.0060, complete all as specified and directed.

ANNAPURNA ENTERPRISES

TARKESHWAR DASS CONSTRUCTION COMPANY

Ganesh Contruction

K B ENTERPRISES

L P Singh and Co.

M/S MAMTA CONSTRUCTIONS

SHREEKRISHNA INFRASTRUCTURE