Special Repairs to MH-15 (OR md accn) at DSC Centre under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

All as per item No 4 here in before but except timber all as specified and directed. Note : Serviceable timber obtained from item No 3 shall be reused.

S&F for structural steel work with rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conform to Fe 410-W (Gde-E- 250 quality-A ) all as specified and directed

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

M&L for mild steel flat iron of size 20 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:3:6, type C1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

M&L for preparing surfaces of area n exc. 0.1 sqm with tar or coal tar black paint each all as specified and directed.

M&L for second class hardwood factory made, panelled shutter 35mm thick (two panesl) with lock rail and panel of 9mm BWP, commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S&F 35mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F first class hard wood beads any size for fixing glass or wire cloth to joineries fixing with nail all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with first class hard wood beading in squares not exc 0.50 Sqm in each pane all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting over a coat of pink primer all as specified and directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L 50mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in flooring finished even and smooth without using extra cement complete all as specified and directed .

M&L 25mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in flooring finished fair and even without using extra cement complete all as specified and directed .

M&L for coloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 300x200x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes 15mm/20mm bore all as directed.

S&F for 15 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) all as directed

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) nominal mix as in beams, lintel over 1.5m span all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) nominal mix as in kitchen slab supported on wall, beam and column and like all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L for use and waste of form work to sides and soffits of lintel, beams etc rough finished surface of concrete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab (horizontal or sloped) floor slab etc n exc 200mm thickness rough finished surface of concrete all as specified and directed.

M&L for use and waste of form work to edges of concrete flat, treads etc similar work exc 5cm but n exc 10cm wide for rough finished concrete surface all as specified and directed.

S&F TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

S&F TMT bars 6 to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

M&L 20mm thick black Granite (table rubbed and polished) as in cooking platform including grounding smooth the exposed edges laid with screed 20mm thick cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed. Note (i) Rate quoted shall deem to include for necessary moulding of sharp edges and screed bed as directed by Engineer-in-Charge.

S&F in repairs Vitreous China Wash basin, white, flat back, size 580 x 450 mm, including CI brackets, waste pipe etc. (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand and fixing of waste pipe etc complete all as specified and directed.

S&F Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F Vitreous China squatting pan “Orissa” pattern, of size 580 x 440 mm white, with integral foot rests, (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and to flushing pipe, anti-syphonage pipe, etc and joint between flushing pipe and socket of WC pan, complete and making good to the floor and fixed in repairs all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

S & F PVC (SWR) floor trap plain with grating including jointing with solvent cement ,75mm bore all as specified and directed.

S & F PTMT grating square 150mm all as specified and directed.

M&L PVC (SWR) pipe 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends with access door any redius all as specified and directed

S&F 15 mm bore bib taps, cast copper alloy, chromium plated crutch or butter fly handle, screwed down, screwed for iron pipe or for PVC pipe or for brass ferrule, all as specified and directed.

S&F 15mm pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

M&L for preparation of new plastered surfaces and applying 3 coat of white wash on walls surfaces all as specified and directed.

M&L for preparation of old plastered surfaces and applying 2 coat of white wash on walls surfaces all as specified and directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

All as per item No 67 here in before but for One 3 Pin, 5 Amps switch socket combination on same board with other switches all as specified and directed.

All as per item No 67 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No. 67 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 4Sqmm unsheathed PVC insulated copper conductor FRLS cable including 4 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified.

Cutting chases on wall of width 30mm and depth 35mm for concealing PVC conduit 20/25mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface and treated with existing treatment such as white wash/OBD/cement base paint etc complete all as directed.

All as per item No 71 here in before but width 50mm all as directed.

S & F modular type, single pole, one way, 6 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F modular type, switch bell push 6 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F modular type, single pole, one way, 16 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S&F modular socket, 2-in-1, 5 pin, 6 amp, 240V, connecting up electrically all as specified and directed.

S&F modular socket, 2-in-1, 5 pin, 6&16 amp, 240V, connecting up electrically all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for two module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for three module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for six module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for eight module all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SP 8way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up complete all as specified and directed.

S & F MCB SPN, 240 Volt, 40Amps including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SP, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with extruded AI, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED of 20 W LED 6000K, model LHEWEBP7IN1W020 of Havells or SSK-T-5 22W of Syska or LCTLN-20-CDL of Crompton Greaves, with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with extruded AI, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED of 10 W LED 6000K, model LHEWEBP7IN1W010 of Havells or LCTLN-10-CDL of Crompton greaves or SSK-T-5 12W of syska , with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Taking down unserviceable bulk head fittings from wall, Supply and fixing LED street light fittings of 30 watts on wall/pole of height 3 to 5M of energy saving and environmental friendly long life made up of pressure die cast aluminium housing with high power LEDs as lighting source and lense embedded PC cover having IP 65 protection of model No SL30WLED757SASYBOPC of HAVELLS or equivalant of CG or Philips including suitable type GI bracket, clamps etc and electrically connecting up all as directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings nd electrically connecting up all as directed.

S&F in repalacement LED ball type lamp 10watt all as directed.

S& F calling bell electric AC 240V, single pole, ding dong type and connecting up electrically all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note :- Rate quoted shall deem to include for GI earth and GI pipe lead upto 7.5m length.

S&F modular stepped type electronic fan regulator, two module full rotation, 120W, SP, 230V onnecting up electricallyall as specified and directed.

Taking down carefully ceiling fan/exhaust fan with rod from ceiling / roof and refixing the same after repairs of civil works and connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan all as specified and directed.

Safarulla padikkal