PERIODICAL SERVICES, REPAIR TO ROOFING, FLOORING, SANITARY FITTINGS AND MISCELLANEOUS WORKS IN CERTAIN BUILDINGS AT ICGAE PORBANDAR UNDER GE I CG PORBANDAR.

Amount

SCHEDULE 'A'

M& L Precast cement concrete type C1, 1: 3 : 6 (20 mm graded stone aggregate) block masonary with solid blocks ,exc,10 cm in width and setting in CM 1:6 complete all as specified.

M&L for pre-cast RCC 1:2:4 type B1 (using 20mm graded aggregate) as in cover slabs set in cement Mortar 1:4 and finished all exposed surfaces of concrete even and fair without using extra cement.

M&L precast cement concrete solid building blocks masonary type C1 1:3:6 (20 mm graded stone aggregate) 10 cm in width and setting in mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregate)as in chajja, lintels over 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, parapets and railings up to 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating any height including necessary scaffolding, ladder & formork etc complete all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound.

M&L 2nd class hard wood Plain fillets. square, rectangular or triangular in section,of sectional area not exceeding 3 sqm clean sawn, secured with nails or brads, fixed in repairs.

S&F 2nd class hard wood plain,solid,straight chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints complete all as specified and as directed by Engineer-in-Charge.

S&F 30mm thick 2nd class Hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F 35 mm thick 2nd class Hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: fixed to chowkats.

M&L 35mm thick Flush shutters , solid core construction, with block board core and plywood face panels, covered with decorative face veneer with lipping/frame on both sides complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sq.m and n.exc 2 sq.m each

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames).

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame)

S & F 30 mm thick factory made solid panel PVC door shutter conforming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming stiles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge Make :- M/s Sintex Industries Ltd, M/s Rajshree Plastiwood Ltd,

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with 19x 19mm MS square tubes, provided with EPDM rubber gasket throughout the frame fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge Make :- M/s Sintex Industries Ltd, M/s Rajshree Plastiwood Ltd,

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification

S&F 25 mm thick lnsulated PVC Wall Lining consisting of PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick wood grain printed PVC sheet duly fitted into the wall as per specifications.

S&F in repair aluminium alloy anodised sliding door bolt with hasp staple (bolt type) length 300mm

S&F in repair Aluminium, anodised, barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F in repair 150 mm long aluminium alloy handles, Fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F in repair 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 150mm long Aluminium anodized barrel tower bolts of extruded section of bolt (ISI Marked) complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 30mm wide flaps Continuous (piano) hinges, mild steel, bright finish or electrogalvanised (ISI Marked) complete all as specified and directed.

S&F 150 mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F 40mm dia cupboard knobs fixed with nuts scrues and washers of brass polished

S&F in repairs aluminium extruded section door closer hydraulically operated regulated designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed

S&F 100mm long Aluminium anodised Hasp & Staple, safety type with MS hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 20mm dia Fancy type, Tubular towel rail, , brass CP, 60cm long between flanges complete all as specified and directed by Engr-in-Charge. Make:- CERA Cat Pat No-F5003102 or Equivalent

S&F Aluminium anodised XPM mesh,24 gauge thickness, cut to size and fixed to Aluminium joinery as mosquito proofing mesh of wire and aperture size ,as per the sample approved and complete all as directed by Engr-in-Charge

S&F in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engr-in-Charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed in repairs

M&L Mild steel CRS TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

S&F Roof trusses (framed), trussed, purlins, crane gantres, rails and fasteings and heavy bracket framing (Beam, tee, angle, channel or flat, sections) including distance pieces, cleats etc. Fe 410-W 9Gde-E-250) Quality A complete all as specied and as directed.

S&F GI grid framework (Size of grid 605mm x 605mm) seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre including 12 mm thick Gypsum board fixed with screw as per manufacturers instructions, priming surfaces with alkali resistant primer and applying two coats of oil emulsion distemper complete all as specified and as directed

M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI bared corrugated steel roof sheet 0.50 mm thick of an column having tensile strength of 550mpa fixed with self drilling screws complete all as specified and directed.

M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2kg/m2 incl cleaning surface all as specified and directed

M&L APP Based Polymeric memberane minimum weighing 3 kg /sqm and minimum 3mm thick Reinforced with polyster non wove fabric (wt not less than 150 gms/ sqm) laid on primed surface by forced application including taking down old membrane of any description complete all as specified and directed

Taking down rain water pipe , eaves gutters, soil pipes,waste pipes (any size and pattern) including all fittings heads shoes bends swan necks etc

S&F 12 mm thick plywood, grade BWR, type BB, fixed with screws to wooden surface with screws and rawl plug including drilling all as directed.

S&F 12mm thick Pre-laminated particle board,interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work all as specified and directed

M&L 12 mm thick prelaminated (Both sides ) Medium density fibre board exterior grade fixed with screws or glazing clip, fixed with panels to aluminium doors/partitions .

M&L 18mm thick Granite (of any type) for Wall /dado & skirting of riser of step (table rubbed and polished) including 15 mm thick rendering in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture pigements to match the shade of granite all as specified and directed.

M&L 18mm thick Granite (of any type) in Flooring (table rubbed and polished) and including 20 mm thick Screed Bed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture pigments to match the shade of granite all as specified and directed

M&L 75mm thick Plain cement concrete type C-1, 1:3:6 (using 40mm graded stone aggregates) as in plinth protection finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L coloured glazed ceremic tiles of size 450x300x7 mm thick in vertical surfaces such as skirting,dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat in 10 mm thick 1:4 including dismantling existing tiles complete all as specified and as directed by Engineer-in-charge.

M&L coloured glazed ceremic tiles of size 450x300x7 mm thick in vertical surfaces such as skirting,dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat in 10 mm thick 1:4 complete all as specified and as directed by Engineer-in-charge.

M&L Non skid coloured ceremic tiles 7 to 8 mm thick area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick 1:6 including dismantling complete all as specified and as directed by Engineer-in-charge.

M&L Vitrified dark shade,Double charged ceremic tiles 9 mm thick (square/rectangular) polished area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick 1:6 including dismantling complete all as specified and as directed by Engineer-in-charge.

M&L Vitrified double charged ceramic coloured tiles with light shade 9 mm thick Square or Rectangular polished area of each tilles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15 mm thick screed bedding in cement mortar 1:6 including dismantling complete all as specified and as directed by Engineer-in-charge.

M&L 80 mm thick, M-40 grade, machine pressed precast concrete interlocking paver block of any shape and size with grey cement and pigment confirming to IS 15658-2006 complete all as specified

M&L Sand filling under paver block including watering and consolidation complete all as speified and directed.

Roughening surfaces of old concrete floor by picking sweeping cleaning & washing down with water to remove dust etc incl removal of old treatment of any description and applying one coat of neat cement slurry @ 3.00 Kg/Sqm complete all as directed by Engr-in-Charge.

M&L Rendering 15 mm thick in CM (1:3) using water proofing compound as per manufacturer instruction as in roof and chajjas complete all as directed by Engr-in-Charge. Note : Water proofing compound will be measured and paid separately.

M&L 5mm thick rendering in CM 1:3 on concrete surfaces on ceiling finished even and smooth without using extra cement all as specified

M&L 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement all as specified

M&L 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement all as specified

Taking down cement plaster includiing raking out joints hacking for key and scrubbing down with water complete, all as specified and directed by Engiiner-in-Charge

M&L Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer on walls complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of weather proof acrylic exterior emulsion paint over a coat of acrylic primer all as per the manufacturers instructions, complete all as specified and directed by Engr-in-charge.

M&L Preparing old plastered / decorated surface of wall including cornices etc by brooming down and applying one coat of oil bound distemper complete all as specified and directed by Engineer in Charge. (Note: After painting cleaning of all floors,glass & furniture shall be done by the contractor on his own arrangement).

M&L Preparation of old plastered /decorated surfaces of Ceiling and applying one coat of OBD all as specified and directed.

M&L Preparation of old plastered surfaces of ceiling and applying one coat of white wash all as specified and directed.

Complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 3 mm thick wall care putty (water proof) complete all as specified and darected.

M&L Preparation of old plastered wall surfaces and applying one coat of acrylic emulsion exterior grade (100%) complete all as specified and as directed

S&F 6 mm thick Sheet glass , ordinary quality and glazing with oil putty / rubber neoprene in square exc 0.5 sq. m in each pane

S&F in repair 4mm thick Figured glass, pin head type and glazing with oil putty / rubber neoprene in squares n exc 0.5 sq. m in each pane including hacking out old broken glass.

M & L Preparation of new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer of approved shade complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of zinc chrome primer of approved shade , complete all as specified and as directed.

M & L Preparation of old wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of old steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint , complete all as specified and as directed.

S&F in repairs 15mm dia Bib taps, with flange chromium plated cast copper alloy with crutch or butterfly handle complete all as specified and directed. Make : Prayag (Cat Pat No-8306) or equivalent as approved by Engr-in-Charge

S&F 500 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe and provision of check nuts including dismantling of existing tank and removal to store.

S&F 1000 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe and provision of check nuts including dismantling of existing tank and removal to store.

S&F in repair 15 mm dia Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed by Engineer in Charge. Make: Prayag (Cat Pat No-9802) or Cera.

S&F 160mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including PVC/GI clamps of approved shape and size approved by GE at any height, any location, any floor including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

S&F 160mm dia PVC (SWR) bends/shoes any radius fixed to pipe at any location/height including necessary scaffolding etc complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including PVC/GI clamps of approved shape and size approved by GE at any height, any location, any floor including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm dia PVC (SWR) bends/shoes any radius fixed to pipe at any location/height including necessary scaffolding etc complete all as specified and as directed by Engineer-in-Charge.

S&F in repair CP brass 125mm size shower rose with rubit cleaning system with shower arm, swivel joints and flange suitable for 15mm bore GI tubing complete all as specified. Make : Prayag or equivalent

Supply and fixing in repairs angular stop valve cast copper alloy ,screwed down ,high pressure or Capstan head handle screwed both ends for iron pipe or for union and fix of size 15 mm bore Make: Prayag (Cat Pat No-8510) or Cera.

S&F in repairs 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed.(Minimum weight 20mm-210gms) complete all as specified and as directed by Engr-in-Charge Make: Prayag (Cat Pat No-152) or Cera.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm Make : Prayag and equivalent as approved by Engr-in-Charge

S&F Stainless steel sinks 1mm thick kitchen with plugs,washers and wastes;including bedding in cement mortar on to dwarf wall or including cantilever brackets and connecting union to pipe,overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified & directed, fixed in repairs.

S&F in repair Vitreous China wash downwater closet pan (pedestal pattern), white (including fixing bolts & flush pipe, plastic water closet seat,black, closed pattern with bottom, and cover and mild steel chromium plated or aluminised hinging device etc.) complete all as specified and directed by Engineer-in-Charge Make :- Prayag or equivalent

S&F in repairs, Plastic water closet seat covers, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device. Make :- Prayag or equivalent

S&F in repair vitreous china squatting pan ,Orissa pattern size 580 x440 mm white,with integral foot rests .

S&F in repair 10 lit.capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete all as specified. Make : Prayag (Cat Pat No-501) or equivalent as approved by Engr-in-Charge

S&F Wash hand basin vitreous china White flat back size 550mmx400mm including cast iron brackets, chromium plated waste coupling, PVC connection, waste pipe up to floor trap etc in repair all complete as specified. Make: Prayag or equivalent

S&F in repair 5mm thick sheet glass shelf and 120mm wide with copper alloy, CP bracket guard and railing 60cm long complete all as specified and directed.

S&L 16 mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&L 20mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

Demolition of stone /boulder masonary work built in CM including all quoins, arches, pillars etc & removing from site.

Dismantling of stone slabs and tiles of any description in floors, aprons etc laid bedded and pointed in any mortar.

Demolition of cement concrete( unreinforced ) in floors and pavings n.exc15 cm thickness (below or above ground level)

Demolition of reinforced cement concrete of any description and in any position and disposal of debris up a distance n.exc 100m where directed

Dismantling Structural steel work including doors, gates but excluding framed truss etc.

Dismantling plain or corrugated steel sheeting, any gauge, thickmness, including nainital or similar pattern roof coverings

Dismantling of wall and ceiling boards (fibre pulp insulation etc) or insulation boards / slabs /blankets any thickness, including cover fillets.

S&F 100 mm long Stainless steel Butt hinges

S&F 75 mm long Stainless steel Butt hinges

S&F in repairs 25mm dia Powder coated aluminium decorative type curtain rod complete all as specified and as directed. Note: colour of curtain rod shall be approved by Engineer-in-Charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 100mm x 5.5mm to 6.5 mm thick with necessary channels and clips complete all as specified and as directed by Engr-in-Charge,

S&F in repair Health Faucet square with 1 mtr tube and hook complete all as specified and as directed by Engr-in-Charge, fixed . Make : Prayag (Cat Pat No-BEA-85) as approved by Engr-in-Charge

S&F in repairs 32mm dia PVC (flexible) waste pipe, 800mm long for WHB/Kitchen sink/Urninal complete.

S&F in repairs PVC lid for water storage tank of capacity 500ltrs suitable to existing make of tank, all as directed by Engineer-in-charge.

S&F in repairs PVC lid for water storage tank of capacity 1000ltrs suitable to existing make of tank, all as directed by Engineer-in-charge.

Providing and fixing Aluminum Composite panels in all coloures of approved brand for external / internal wall cladding at all heights and elevations including necessary aluminium composite panel consist of 3mm thermoplastic core of anti oxident LDPE sandwitched between two skin of 0.5 mm thick alloy sheet making a total sheet thickness of 4 mm. The surface shall be finished with PDVF base coating on the top side and service coating on the reverse side shall be with a polymer paint. The system to be fixed to the brick/stone/masonry/RCC walls/framed structure with necessary clamps, bracket and anchor fasteners fixed over and including base frame fabricated with aluminium square pipe of size 25mmx25mm with 1mm thickness in 600mmx600mm size grid including stainless steel screws, nut, bolts, washers, cleats, weather silicone sealent for groove filling, backer rods etc, complete all as per Manufacturer instruction and all as specified and as directed by Engr-in-Charge. All Clamps and brackets shall be hot dip galvanised minimum 80 micron thick and confirmed to IS : 4759 - 1996. The extruded aluminium sections shall be anodised in approved colour with anodic coating minimum 20 microns. (items include cost of aluminium frame, ACP Panels, Cramps, weather sealent, gasket, foam, fixtures, scaffolding, all machineries and any other fastening streps, nuts, bolts, rivets, washers, etc complete). The manufacturer shall also give guarantee/warranty for ACP panels for a period of Five years. Make of ACP:- ALUPEX/ALUDECOR/ALSTRONG.

S&F in repairs PVC Bathroom Mirror cabinet of size 550 x 450 mm Make : Prayag, Nilkamal, Supreme

S&F 12 mm thick toughened sheet glass and fixed with patch fittings with cover plate of SS 316 grade, necessary accessories for fixing door/partition including cutting holes of any size in floor and wall including taking down old unserviceable glass of any description...

S&F Stainless steel pipe of grade 316, of any dia for railling / balusters over existing parapet including base, collars, caps, head caps and anyother specials etc including necessary welding, polishing and drilling in masonary and filling with epoxy grout etc including taking out old SS railing and removing to store complete all as specified and directed by Engineer in charge.

S&F in repair viterous China Counter top wash hand basin of size 560 x 410 x 180 mm including making necessary connection of water supply and waste pipe. Make: Prayag ( Cat No: 4790) or Equivalent

M & L 12 mm thick vitrified parking tile of area exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick 1:4 including dismantling complete all as specified and as directed by Engineer-in-charge. The model/Pattern of tile shall be as approved by GE

S&F Steel powder coated finials for 25mm dia curtain rod complete all as specified and as directed by engineer-in-charge.

S&F fabricated powder coated aluminium anodised doors, windows, partitions and ventilators using aluminium sections of size and type approved by Engr-in-Charge including jointing clips, snap beadings,locking arrangement etc, complete all as specified and as directed

S&F rubber gasket of size 50 mm x 6mm for aluminium door, window and partition wall for fixing glass panes or prelaminated particle board etc complete all as specified and as directed.

S&F Roller for fabricated aluminium anodised doors, windows, partiotions and ventilators complete all as specifed and as directed.

M&L Preparation of old surfaces and applying 3mm thick self levelling epoxy flooring including removal of existing , filling of cracks in PQC slab complete all as specified and as directed. Make: FOSROC, PIDILITE, CHOKSEY CHEMICAL LTD.

M&L Building number Plate made with Acrylic Sheet of Size 300mmx200mm and with Alphabatic number writing, with Radium Tape, and fixed with screw complete all as specified and as directed by Engr - in - Charge

M&L Granules(Grit finish) textured homogeneous wall finishing system including preparation of old surface consisting of a two component system of dry granules (25 Kg per Pack) made of 92% silica particles coated with fade resistant pigment, 100% acrylic polymer bonding agent (5 Kg per pack) with the applied thickness of the coating being between 0.8mm -1.2mm to be applied on curved, smooth level plaster without key, as per manufacture directions, for usages to be applied and approved applicator of the manufacture as per the direction/ supervision of the Engineer-in-charge, all complete. The above textured coating should conform to surface spread of flame class one of BS 476:Part 7:1971 and pull off strength of the coating to meet JISA 6909 on smooth plastered surfaces complete all as specified. Make:- Bakelite Hylam Limited or equivalent make approved by the GE.

Repair/ servecing / easing of hanger steel gate shutter (not exceeding 4.00 m wide and 10.00 m hieght) sliding/ rolling over wheels (minimum 06 Nos) on track at floor and with rollers (minimum 08 nos) at top with following specifictions and as directed by Engineer-in-Charge. :- (i) Servicing of existing ball bearings mounted at both sides by claening, greasing etc. complete all as specified and directed. (ii) Cleaning, greasing and strengthening of tracks by minor welding fixed over floor and minor realignment of track, inposition, without taking out tracks at both ends if required. (iii) Minor welding of guide bracket and other strutural steel members of gate as required.

K K Construction Co

JAMNAGAR ELECTRIC AND MACHINERY CO