Annual Plan-1574/2026, METHALAYIL PATHIKKAL CHEERP KUTTOOLI CHEERP RENOVATION PHASE-2, WARD-4, SECTOR-1-KOZHIKODE CORPORATION-General Civil Work

CONCRETE

15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

OD382438/2025-2026:RING BUND Type II putting up ring bund with earth fille gunny bags of top width 1.0m bottom width 2.0m height 2.0m side and filling in between with earth to form ring bund and maintaining the same leak proof till the completion of the work and clearing the site by dismantling the bund after completion of the work etc. complete

50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

OD382440/2025-2026:Coconut pile- Supplying and stacking well matured straight coconut post for driving down through various strata bellow bed level including cost conveyance labour charges etc complete(based on DAR 60.64.1)

OD382439/2025-2026:Coconut pile-Drriving down coconut pile to lines and levels trough various strata including all hire charges andlabour for fixing staging platform and all otherappliances necessary for pile driving down after pointing the bottom end

51.2.3:Filling with Quarry Muck Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.3.2:Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

OD382442/2025-2026:85.101 Supply of MS plates confirming to IS 2062GrB including of cost of conveyance charges.

OD382443/2025-2026:85.102 Supply of MS Tees angles Joists ISMB ISMC Confirming to IS2062GrA/B Including of cost of conveyance charge

OD382448/2025-2026:85.108. Fabrication , erection and commissioning of Structural Steel Embedded parts in IS2062 Grade and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charge etc complete but exculding cost of materials already supplied

OD382445/2025-2026:85.116 Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

OD382449/2025-2026:85.117. Supplying and fixing in correct position with specified initial interface the Angular type rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

OD382447/2025-2026:85.111. Erection of the gates safely in the grooves , assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site

OD382446/2025-2026: Derived 85.114 painting surfaces of the shutter with three coats of high build rust encapsulating modified coal tar epoxy coating the total film thickness is not less than 250microns , Manual preparation of surface including wire brush and papering all material , labour charges cost of testing all painting material all incidental charges hire of T&P etc complete as per the direction of department

OD382441/2025-2026:Derived from 85.113 painting all the exposed surface of gate and embedded parts with two coats of epoxy coal tar black paint confirming to is14948 with a minimum film thickness of 150+/-5 microns per each coats of priming coat applied with zinc primer containing not less than 85% of zinc dry film with a film thickness of 70+/-5 microns so that the total film thickness for all coats including priming coat at any rate is not less than 350microns over the grit blasted and cleaned surface to class A standard of IS 14177 including cost of all materials labour charges , cost of testing all painting material all incidental charges hire of T%P etc complete as per the direction of departmental officer at site.

OD382444/2025-2026:Conveying and fixing manual operating mechanism gear including screw threaded rod of 63mm