Composite interior works for upper basement floor at Sahya building Cyberpark, Kozhikode.

Amount

CIVIL WORKS

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

od188709/2019_2020 : Providing and laying precast machine moulded CM 1:4 soild blocks in block size of 400 x 200 x 200mm masonry of specified thickness with blocks of grade C(5) with mini compressive strength of 5 N/mm2 etc complete above plinth level upto all floor level

6.38 : Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above floor 2 level up to floorV level in cement mortar 1:4 (1 cement :4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6.13.1 : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement : 3 coarse sand)

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

14.53.1 : Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

od188752/2019_2020 : Providing and laying vitrified floor tiles in different sizes, tile spacer of 3 mm to 4 mm with epoxy grout (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (Basic Cost - 75/sft) Tile Size - 600mm x 600 / 800 x 400 mm .

od188758/2019_2020 : SKIRTING : Providing and laying of bouble charged Vitrified tiles in different sizes, tile spacer of 3 mm to 4 mm with epoxy grout (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm (Basic Cost - 75/sft)

od188762/2019_2020 : Providing and fixing Ist quality double charged vitrified wall tiles conforming to IS: 15622 with tile spacer of 3 mm to 4 mm with epoxy grout (thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.basic cost 65/- per sqft(300X600mm)

od188768/2019_2020 : Providing and laying Matt finished Vitrified floor tiles of size 600x600 mm with tile spacer of 3 mm to 4 mm with epoxy grout (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. basic cost 70/- per Sqft

od188788/2019_2020 : 1.Grinding the surface cleaning the surface thoroughly & removing laitance completely.<br>2.Providing and applying FLOWPRIME as primer coat. <br>3.Providing and applying 5mm thick FLOWSHIELD SL SELF SMOOTHNING EPOXY FLOORING as approved color and allow it dry as per manufacturer’s specifications etc and as directed

9.1.1 : Providing wood work in frames ( 100x60mm)size: of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing Second class teak wood frame Flush door as per drg.to detail 30mm thick (finished) flush shutters in single leaf with external lipping and phenol formaldehyde bonding and finished with Laminate . The furniture and fittings shall be fixed in the shutter/ frame using Brass screws. The rate shall be inclusive of cost of materials, labour charges etc. All the materials to be used on the work shall be got approved by The Engineer-in-charge before actual use on work.

Providing and fixing SS- Tower Bolt 250mm x 12mm

Providing and fixing SS- Tower Bolt 200mm x 10mm

Providing and fixing SS- Handle Dtype 10 mm size

Providing and fixing Aluminum hanging floor door stoper ISI mark anodised ( anodic coaring not less than grade AC 10 as per IS :1868) transperet for dyed to required clour and shade with necessary screws etc. complete. Single rubber stopper

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

4.2.3 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

22.3 : Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

od188838/2019_2020 : Providing Core cutting of 150mm dia at RCC surface neatly and complete as per the directions of the Engineer in charge .

od188840/2019_2020 : Providing and laying 150mm thk. light weight concrete consisting of 1 part Portland cement to 6 part vermiculite concrete aggregate including well compacted vibrating, curing etc., The rate shall include all leads and lifts,centering and Shuttering(excluding reinforcement), materials, labour, equipment and machinery, loading and unloading, transportation and all other incidential charges etc all as complete and directed by Engineer in charge.

16.83 : Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

16.84 : Laying old cement concrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost.)

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

od188847/2019_2020 : Labour charges for shifting and removal of all debris and waste inside the building to the place pointed out by the Engineer in charge

INTERIOR WORKS

od188672/2019_2020 : Gypsum Board Partition: Frame work: Aluminium frames of 50x50X2 mm, vertically at about 600mm centres varied along columns wall ends, junctions of walls, as necessary. Horizontally of same size of frame at floor level, 900mm, 2100mm and roof level. 50 x 25mm at 450mm level fixed in position. The vertical frames fixed to soffit of slab with necessary screws, MS clamps, rawl plugs, expansion fasteners, etc., complete. (b) Lining Work: 15 mm Gyp board on both sides of framework from floor level to 900 mm level and 2100 mm level to false ceiling level . The horizontal and vertical joints of the Panel to be staggered and all joints to be taped and finished with joint Paper tape and jointing compound. And the boards to be filled with Acoustic insulation with glass wool ( Density 22 kg/m3 ) wrapped with tissue paper, wool shall be wire braced to prevent it from lumping down over a preiod of time.The Gypsum board joints to be finished in all respects (using tape, wall putty if required) ready to receive interior finishes, as per project specifications. Supply & finishing with 1 coat of approved primer and 2 coats of Acrylic emulsion of approved colour and shade on both sides of Gypsum partition walls as shown in drg. Note: Measurement for the partition area shall be considered from floor level to false ceiling level only. Required supports to be provided by the contractor upto sofit of slab.

od188678/2019_2020 :Ply Wood Covering on the existing Frame work above false ceiling - in between Offices on both sides of the frame (b) Lining Work: Providing and fixing 12 mm thick Com ply on both sides of existing framework from false ceiling level to soffit of slab. as per project specifications.

od188684/2019_2020 : SINGLE GLAZED TOUGHENED GLASS PARTITIONS - Supply and Fixing of Slim Glass partition of 10mm Toughened Glass using DORMA Alexa System-45 Frames to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using DORMA Alexa BP45 Profiles at Top & Bottom & Alexa SP45 at sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. DORMA Alexa H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel Alexa MP45 & BP45 Overpanel Profile to be used.In case of Open glass edges EP45 End Profile to be used. all be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system.All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. Approved Manufacturer: NOTE : The neccessary frame support to be installed upto soffit of roof slab.

od188690/2019_2020 : 122mm thick both side SB + HB partition system (Max reachable height 4.6mtr) Floor & Ceiling channel is anchored to the floor & True ceiling using Gyproc® Rawl plug 08x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade) /Hilti Nail anchor fasteners at 600mm c/c in zig-zag manner. Floor channel to be wrapped with 7Op Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gyproc® Soundbloc board strip of 72mm width is placed between ceiling channel and RCC slab when fire rating is more than 30mm. A GypSerra noggin channel {Material-IS 513,Y/S-300 Mpa, Finish - AZ15O (IS 15961)) of 70x0.5mm width has to be provided at the horizontal joints of the two boards. First layer of Gyproc® boards to be screw fixed with Gyproc® drywall screws of 25mm at minimum spacing of 600 at centre and 600mm at periphery and Second layer to be screw fixed with Gyproc® Habito drywall screws of 35mm at minimum spacing of 300mm at centre and 300mm at periphery. 50mm Glass wool slab of density 2Okg/m3 shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc® Pro-Fill Jointing compound Air Dry (Conforms to ASTM C475), Gyproc® Joint Paper tape or fibre tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

od188703/2019_2020 : Double skin solid Partition with Laminate finish: (a) Frame work: Aluminium frames of 50x50X2 mm, vertically at about 600mm centres varied along columns wall ends, junctions of walls, as necessary. Horizontally of same size of frame at floor level, 900mm, 2100mm and roof level. 50 x 25mm at 450mm level fixed in position. The vertical frames fixed to soffit of slab with necessary screws, MS clamps, rawl plugs, expansion fasteners, etc., complete. (b) Lining Work: 12.5 mm Gyp board on both sides of framework from floor level to 900 mm level and 2100 mm level to false ceiling level . The horizontal and vertical joints of the Panel to be staggered and all joints to be taped and finished with joint Paper tape and jointing compound. And the boards to be filled with Acoustic insulation with glass wool ( Density 22 kg/m3 ) wrapped with tissue paper, wool shall be wire braced to prevent it from lumping down over a preiod of time.The Gypsum board joints to be finished in all respects (using tape, wall putty if required) ready to receive interior finishes, as per project specifications. Providing and fixing Partition with shutter of 12 mm thick com ply on both sides with 1mm thick laminate finish of 6 mm x 6 mm also with half round nosing laminated edge finish of required leaves with all necessary, complete Note: Measurement for the partition area shall be considered from floor level to false ceiling level only.

od188710/2019_2020 : Ply wood Laminate finish - Partition: (a) Frame work: Aluminium frames of 75x25X2 mm, vertically at about 600mm centres varied along columns wall ends, junctions of walls, as necessary. Horizontally of same size of frame at floor level, 900mm, 2100mm and roof level. 75 x 25mm at 450mm level fixed in position. The vertical frames fixed to soffit of slab with necessary screws, MS clamps, rawl plugs, expansion fasteners, etc., complete.And the boards to be filled with Acoustic insulation with glass wool ( Density 22 kg/m3 ) wrapped with tissue paper, wool shall be wire braced to prevent it from lumping down over a preiod of time (b) Lining Work: 12 mm com. ply on both sides of framework from floor level to 900 mm level and 2100 mm level to false ceiling level finished with 1mm thick laminate from floor level to false ceiling level on both sides of approved colour and shade. basic cost of Laminate 48/- per sqft. All concealed faces of com. ply and frame work should be finished with one coat of wood preservative paint and exposed faces of Steam beech beading to be polished with melamine to the satisfaction of the Client/ Architect. Note: Measurement for the partition area shall be considered from floor level to false ceiling level only.

od188715/2019_2020 : GLASS DOOR : Supplying and fixing Fully openable Patch Fitting partition and door of ' of Approved make with "PT STANDARD" range Fittings to get a clear height with top & Side Fixed panels. In general the openable door cum Fixed panel consists of sliding channel with all fitting and Corner Fittings PT91, Top pivot PT24, Top patch PT20, Bottom patch PT10, with BTS 75 V Floor spring with SS cover plate, Standard Spindle US10, corner lock at top & bottom, Euro profile cylinder with 3 keys, lock strike plate LKP , Pull handle(TGDI35025) SS Satin Finish and 10mm thick clear toughened glass as per design and all confirming to manufacturers specification. SS fixtures shall conform Grade SS 304 to BS 7352. The rate shall be inclusive of wastage and necessary hardware's etc; as required for complete the works.Rate shall include for providing transport charges, handling, loading and unloading, Installation, protecting the module and glass till handing over, testing, commissioning all necessary hardware's, Structural supports if any, etc. complete and all as per manufacturers specifications as directed. (GLASS DOOR)Note: The price shall include all fixtures like handles, locks, door closer,door stopper etc)

od188719/2019_2020 : Supplying and Fixing Privacy Frosted Glass Sticker in glass panels where ever found necessary as per the direction of the the officer in charge incluidng cost of all materilas, labour charges for fixing etc. complete

od188724/2019_2020 : Supplying, providing and fixing Aluminium retro fitted skirting of anodised mat silver finished of size 3000 x 2 x100 mm incluidng cost coneynace labour charges for fixing etc. complete. Engineer in charge

od188728/2019_2020 : 2HR Fire Rated Steel Door: Providing and fixing fire resistant un insulated two hours Fire rated steel door (Sakthi mat door or approved equivalent make) of double rabate steel frame profile of size 145 x 55mm with bending radius of 1.2 mm made up of 1.2 mm thk galvanized sheet conforming to IS 277. The frames shall have provision for nos. anchor bolt fasteners on each vertical jamb, 3mm thk hinge back plate pre-drilled to receive hinge screw. The frame shall be in three pieces bolted at top.The frame shall be primed with zinc phosphate stoving primer and finished with synthetic enamel paint of approved colour. The steel door shutter shall be constructed out of 1mm thk galvanized steel confirming ot IS 277 with fully flushed double skin door having interlock seam arrangement at stile.(Rate to include for lock, handels on both side and push plate of 150 x 200 mm and door closure). The door construction shall be fire retardent & heat insulation suitable for stability, integrity with two hours fire rating, type tested at CBRI Rookee as per IS 3614 (Part II) and BS 476 (Part 20). The thk of the shutter shall be 46 mm. The shutter shall be primed with zinc phosphate stoving primer and finished with synthetic enamel paint of approve make of the fire rated vision panel of size 200 x 300 mm using imported make "Pyron" make fire rated glass. Frame for 900 X 2100 mm

od188733/2019_2020 : 2HR Fire Rated Steel Door: Providing and fixing fire resistant un insulated two hours Fire rated steel door (Sakthi mat door or approved equivalent make) of double rabate steel frame profile of size 145 x 55mm with bending radius of 1.2 mm made up of 1.2 mm thk galvanized sheet conforming to IS 277. The frames shall have provision for nos. anchor bolt fasteners on each vertical jamb, 3mm thk hinge back plate pre-drilled to receive hinge screw. The frame shall be in three pieces bolted at top.The frame shall be primed with zinc phosphate stoving primer and finished with synthetic enamel paint of approved colour. The steel door shutter shall be constructed out of 1mm thk galvanized steel confirming ot IS 277 with fully flushed double skin door having interlock seam arrangement at stile.(Rate to include for lock, handels on both side and push plate of 150 x 200 mm and door closure). The door construction shall be fire retardent & heat insulation suitable for stability, integrity with two hours fire rating, type tested at CBRI Rookee as per IS 3614 (Part II) and BS 476 (Part 20). The thk of the shutter shall be 46 mm. The shutter shall be primed with zinc phosphate stoving primer and finished with synthetic enamel paint of approve make of the fire rated vision panel of size 200 x 300 mm using imported make "Pyron" make fire rated glass. 1000 x 2100mm Single leaf door

od188747/2019_2020 : Supply and providing P/F vision panel in Fire-rated door including cost conveyance fixing charge etc complete

od188753/2019_2020 : STORAGE UNITS: Providing and fixing low height storage unit (600mmx1050mm) and Full height storage unit (350/400/600mmx2100mm) in two compartment. using 18mm thick comply in storage two sides, Rear, top & Bottom, front shutter from 75mm level to 1050mm level finished with 1mm thick laminate of approved colour and shade. with necessary hardware fixtures including brushed 100mm long SS handle, soft closing hinges, locks with keys, etc., complete. All concealed faces of com. ply finished with one coat of wood preservative paint and exposed faces of steam beach beading polished to the satisfaction of the Client/ Architect. The inner side of the storage finished with 0.8mm thick laminate of approved colour and shade.

od188759/2019_2020 : COLUMN CLADDING: Providing and fixing column paneling , in general it shall be made of Aluminium extruded sections of size 50x25mmx1.5mm thick in both horizontal and vertical direction at 600 mm c/c spacing. The framework shall be covered with single layer 8mm thick BWR plywood on sides up to 75mm above false ceiling. The cost of necessary hardware's etc; as required for complete the works. Actual seen surface area.(i.e) from FFL to bottom of false ceiling height will be measured and paid. Laminate /Veneer on top of this will also be codidred along with qouted rate.

od188763/2019_2020 : Glo Panel: Providing and fixing 8mm thick MDF board is thenfixed to ceiling section with 25mm drywall screws at 230mm centres finished with 3.5mm thick veneer of approved shade finished with two or more coats of PU polish over one coat of sealer/12mm thick MDF wave board (GLO make ) on to the framework finished with high gloss paint of approved shade. screw fixing shall be done mechanically either with screw driver or drilling machine with suitable attachment. All exposed woodwork/vendor to be melamine polished. All complete as per approval of the architect.

od188769/2019_2020 : Reception table (4000x 600 x750) / similar size: Supply and installation of Reception Table of size Length 4000 width 600mm and 750 (ht) to shape and comprising table top out of 25 mm thk BWR ply board with stiffner of 19mm thk BWR ply. With 2mm edge lipping finish.Foot rest cum CPU stand of required length with same 19 mm thk BWR ply finished of approved colour and shade. 3 sets of Keyboard tray made out of 12mm thick BWR ply of approved colour and shade with necessary Telescopic slides and 50mm Dia SS Brush Finish wire manager of approved make and quality. Storage unit with 12mm thk BWR ply ,450mm wide drawer unit of size (w) 450 x ( d) 600 and 120 mm ( ht ) and below openable shutter supported with 19 mm thk BWR ply at front ,sides and bottom of 75mm high with necessary TW lipping, telescopic drawer slides,Individual locking arrangement, 100mm long brush finish S.S. handles, etc., complete. All exposed faces of Steam beech beading polished to the satisfaction of the Architects. The inner side of the Drawer with BWR ply of approved colour and shade and storage painted with enamel of approved shade, neatly and complete.

od188773/2019_2020 : Writing Board: Providing and fixing of writing board using SG plainlaque glass of 6mm thickness of size 1200 x 900mm to detail as shown in the dwg, fixed with 4 nos. SS Studs, all as instructed by the Engineer-in-charge.

17.32.4 : Providing and fixing 5 mm mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

od188779/2019_2020 : Pin Up Board: Providing and fixing pin up board to detail. Frame work made out of Aluminum of size 50 x 25mm at 30cm centres both ways fixed to wall with necessary screws, at locations as shown in drawing. 9mm thick soft board wrapped with Response fabric. ( Basic cost of fabric- 150-/ metre)

od188783/2019_2020 : Pelmet: Providing and fixing pelmet to shape of size 150x150mm as specified in drawing, in general to be made of 18mm com ply with approved color enamel paint and a coat of primer to match false ceiling as directed by Architect. Rate shall be inclusive of fixing all accessories like Hangar rods,/anchors, sunken screws etc. complete.

od188789/2019_2020 : Supplying and providing 8mm thick Bison board including cost of aluminium frame ( thickness of 50x50mm) and all joineries ,labor charges for fixing etc. complete as per the directions of the Engineer in charge

od188796/2019_2020 : Supplying and providing 6mm thicness Acrylic Sign Board of size 300X550mm where ever found necessary as per the direction of the the officer in charge incluidng cost of all materilas labour charges for fixing etc. complete

INTERIOR FURNITURE

od188673/2019_2020 : Linear Workstation with partition (1200x 600 x750): Supply and installation of linear workstation of size 1200 X 600 X 750 (ht) ,with 25 mm thick pre-laminated particle board tabletop, with wire management access to desktop (with cover). Partition panel to be of glass, 1050mm ht. . Exterior face is of glass partition. Desktop to be supported with Metal Legs. Additional supports viz, Steel angles etc should be considered if required. Dual raceway below worktop and at skirtline (for running electrical and data cables separately ).Metal CRA Powder coated CPU trolley with 04 No's PVC castors, PVC Key Board with sliding mouse pad & Telescopic channels for pulling in and out. with 550W*285D with Channels & Workstation set to include 3 Drawer mobile pedestal (laminate finished)of size 425 W x 550 D x 700 H, including lock, handles and all necessary accessories. Lowest drawer unit to be suitable for filing. All finishes/ colors, as approved (including metal powder coating) to be factory finished. Architectural Ironmongery to be SS finish.

od188679/2019_2020 : Cabin Desks (1500x600x750) / similar size: Supply and installation of 25 mm thick pre-laminated particle board tabletop with curved edges, of size 1500mm W X 600mmD x 750mm H. Table to be supported on metal legs. Power management through vertical riser , cable tray and fliptop. to include3 Drawer mobile pedestal (laminate finished)of size 450 W x 450 D x 650 H, including lock, handles and all necessary accessories. Lowest drawer unit to be suitable for filing. All finishes/ colors, as approved (including metal powder coating) to be factory finished. Architectural Ironmongery to be SS finish .18mm Thick pre-laminated particle board modesty which acts as privacy for user. STORAGE- SIDE size 1200 x 450 x 750 mm ht : Providing and fixing of Storage unit with 25mm thk Prelaminated particle board Top & 18mm Thick Prelaminated particle board sides with 400W Drawers-2 File draws&1 Box drawer with soft closure telescopic channels & SS finish. Handles & central Locking and remaining with openable shutters with PVC edge band - with SS finish. Handles & Centre Locking.

od188685/2019_2020 : Meeting Room Table (2000x900x750) / similar size: Table top is made of 25mm thick pre-laminated particle board finish with 2mm PVC edge banding of approved make and 681 Kg/M3 density with 0.68N/mm2 Tensile Strength, 475 rev Abrasion resistance(Min) with 6.25 mg/100g dry board Formaldehyde content.<br>500Wx120D Aluminum Flipup in anodized finish is considered for wire manager."<br> MS powder coated Triangular legs<br>WIRE MANAGEMENT :MS Powder coate 1.2mm thickness wire tray with switch plate 150D/300D*120H below the table top and Aluminum flipups in anodized finish of 500Wx120D on table top is considered and PVC snake guard below the wire tray for pulling wires are considered.<br> MS Powder coated 1.6mm thickness triangular shape legs with MS powder coated support beams of 40x30 in 1.2 thickness with metal die cast connectors at both the ends for fixing below the table top is considered and 60x30x1.6mm thick metal CRCA tube leg with concealed junction box with 1.2mm thick CRCA covers will provide in middle leg of the clusters to pull wires from floor to wire tray and flowing of cables will be through cable tray of 1.2mm thickness metal CRCA powder coated tray.

od188691/2019_2020 : Conference Room Table (5000x1200x750) / similar size: Table top is made of 25mm thick pre-laminated particle board finish with 2mm PVC edge banding of approved make and 681 Kg/M3 density with 0.68N/mm2 Tensile Strength, 475 rev Abrasion resistance(Min) with 6.25 mg/100g dry board Formaldehyde content.<br>500Wx120D Aluminum Flipup in anodized finish is considered for wire manager."<br> MS powder coated Triangular legs<br>WIRE MANAGEMENT :MS Powder coate 1.2mm thickness wire tray with switch plate 150D/300D*120H below the table top and Aluminum flipups in anodized finish of 500Wx120D on table top is considered and PVC snake guard below the wire tray for pulling wires are considered.<br> MS Powder coated 1.6mm thickness triangular shape legs with MS powder coated support beams of 40x30 in 1.2 thickness with metal die cast connectors at both the ends for fixing below the table top is considered and 60x30x1.6mm thick metal CRCA tube leg with concealed junction box with 1.2mm thick CRCA covers will provide in middle leg of the clusters to pull wires from floor to wire tray and flowing of cables will be through cable tray of 1.2mm thickness metal CRCA powder coated tray

od188695/2019_2020 : Dining Table (2200 mm x 900mm): Dining table of 2200 x 900 x740-750 mmH . Table Top :- The table top is made up of 25mm thick MDF with waterfall top edges finished in PVC Membrane using unique wrap around technology for better aesthetics & long lasting use.Understructure :- The understructure is stainless steel buff finished

od188698/2019_2020 : Visitor chairs : Medium back visitor chair with cantilever base of welded 25mm diameter powdercoat finished .Back Rest -Medium Back made out of treated ply & moulded PU Foam.Seat -Fixed Seat with Waterfall edge for better comfort & blood circulation.Back/Seat Foam-Moulded PU Foam with density not less than 50-60Kg/m3 .Arm Rest -Fixed Armrest with PU arm Pad.Upholstery -Fabrics with 100% polyester.Weight -320 Grams per linear meter.Thickness -222GSM.Back Dimensions :- 470 (Height of seat to Back rest) X 470 (W).Seat Dimensions :- 435 (Depth from lumber point to seat edge) X 490 (W)(or nearby size or dimension).

od188704/2019_2020 : Conference room chairs: Providing & Fixing in Position Medium Back Chair with the following specifications. Seat & Back -Fabric upholstered/Mesh Back.Seat Foam: Made out of moulded PU foam with the following properties.Density 45-60 Kg/m. Armrest :- Fixed Polypropeylene armrest.Lumber Support -Adjustable Lumber Support to suit variable individual heights. Mechanism :- Synchro 1 Mechanism for tilting in different ratio with 1 position of locking and 360 degree revolving type. Mechanism to be tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002.Tension Adjustment: Back tension knob to be provided for tension adjustment. Gas Lift:-DIN 4550 Class 3 Standard & meets ANSI BIFMA performance standards .Tested for 1, 00,000 Cycles.Base :- Nylon Base.Castors :- 50mm Dia nylon castors tested for a static load carrying capacity of 1134Kg .Complies to ANSI / BIFMA X 5.1 – 2002 .Tested for 1,00,000 Cycles .Seat Dimensions :- 470 (Depth from lumber point to seat edge) X 500 (W) OR nearby size. Back Dimensions :- 540(Height of seat to Back rest) X 485 (W) or nearby size.

od188711/2019_2020 : Meeting room chairs : Providing & Fixing in Position Medium Back Chair with the following specifications. Seat & Back -Fabric upholstered/Mesh Back.Seat Foam: Made out of moulded PU foam with the following properties.Density 45-60 Kg/m. Armrest :- Fixed Polypropeylene armrest.Lumber Support -Adjustable Lumber Support to suit variable individual heights. Mechanism :- Synchro 1 Mechanism for tilting in different ratio with 1 position of locking and 360 degree revolving type. Mechanism to be tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002.Tension Adjustment: Back tension knob to be provided for tension adjustment. Gas Lift:-DIN 4550 Class 3 Standard & meets ANSI BIFMA performance standards .Tested for 1, 00,000 Cycles.Base :- Nylon Base.Castors :- 50mm Dia nylon castors tested for a static load carrying capacity of 1134Kg .Complies to ANSI / BIFMA X 5.1 – 2002 .Tested for 1,00,000 Cycles .Seat Dimensions :- 470 (Depth from lumber point to seat edge) X 500 (W) OR nearby size. Back Dimensions :- 540(Height of seat to Back rest) X 485 (W) or nearby size.

od188716/2019_2020 : Work stations : Providing & Fixing in Position Medium Back Chair with the following specifications. Seat & Back -Fabric upholstered/Mesh Back.Seat Foam: Made out of moulded PU foam with the following properties.Density 45-60 Kg/m. Armrest :- Fixed Polypropeylene armrest.Lumber Support -Adjustable Lumber Support to suit variable individual heights. Mechanism :- Synchro 1 Mechanism for tilting in different ratio with 1 position of locking and 360 degree revolving type. Mechanism to be tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002.Tension Adjustment: Back tension knob to be provided for tension adjustment. Gas Lift:-DIN 4550 Class 3 Standard & meets ANSI BIFMA performance standards .Tested for 1, 00,000 Cycles.Base :- Nylon Base.Castors :- 50mm Dia nylon castors tested for a static load carrying capacity of 1134Kg .Complies to ANSI / BIFMA X 5.1 – 2002 .Tested for 1,00,000 Cycles .Seat Dimensions :- 470 (Depth from lumber point to seat edge) X 500 (W) OR nearby size. Back Dimensions :- 540(Height of seat to Back rest) X 485 (W) or nearby size.

od188720/2019_2020 : CEO chairs : High back task chairs with synchro 4 mechanism for tilting with four position locking.Mechanism is BIFMA compliant & tested for 300000 cycles. Back Rest -High Mesh Back. Seat -Fixed Seat with Waterfall edge for better comfort & blood circulation.Back/Seat Foam-Moulded PU Foam with density not less than 50-60Kg/m3 .Gas Lift -BIFMA Compliant Class 3 HP gas lift to absorb seating shocks with a higher stroke length of 120mm which is tested for 100000 cycles.Castors-60mm dia PU castors with twin wheel construction.BIFMA compliant & tested for 100000 cycles.Base-Designer Diecast Aluminium Base with a pitch circle diameter of 650mm.BIFMA compliant & tested for a static load of 1450kg.Arm Rest -2D Armrest with PU arm Pad.Upholstery -Fabrics with 100% polyester.Weight -320 Grams per linear meter.Thickness -222GSM.• Seat :- 460mm width and 470mm depth<br>• Seat to Back rest height :- 650mm.Back Rest Width -500mm.(or nearby size or dimension)

od188725/2019_2020 : Dining chairs : Chair with single moulded polypropylene seat & base with no armrest.Chair to be stackable,seat profiled with a water drain option.

od188729/2019_2020 : Visitor Sofa- Two seater-Manufacturing, supply in position of Executive sofa ) as per the specification mentioned below.Inner Frameworks of Sofa made out of Plywood & kiln chemical treated tropical meranti wood.Seating cushions in 3" elastic webbing(350gsm) with diagonal weave & 7"multilayered foam(32D23D32D HD)with polyester polyfill outer layer(180gsm).Back rest in 2"elastic webbing(250gsm) with diagonal weave & 3"multilayered foam(23D)with polyester polyfill outer layer(180gsm).Outer Finish in superior quality leatherette stiched with nylon bonded thread & stained solid wooden legs.(Colour Options in burgundy & Matte Black).Two Seater size - 1300(l)x850(w)x760(h)(or nearby size or dimension).

od188734/2019_2020 : Corner Table: Manufacturing & Supply in position of Corner table of size 550 x 550 mm x510mm(or nearby size or dimension). Under structure is an assembly of stainless steel tube of 25mm x 25mm cross section with Buff finished.Top & intermediate shelf with 10mm thk toughened glass top with edges polished.

od188739/2019_2020 : Vista or Equivalent make of Roller blinds : Providing and fixing of Vista or Equivalent make of Roller blinds with Approved design and shade. Basic cost of blinds should not be less than Rs.1200 per Sqm

od188743/2019_2020 : Average Cubicles -1525mm W X 2100mm Ht : Supply and installation of Restroom cubicle system that includes intermediate panel, pilaster & door made of BWR .PLY and laminates of single colour . The solid BWR .PLYpact laminate is based on thermosetting resins, homogeneously reinforced with cellulose fibres and is manufactured as per relevant quality standards. Top surface on both sides is melamine coated which is scratch & impact resistant . Intermediate panel is one continuous panel without any joints , All intermediate panels , pilaster & doors shall be 12mm thick with edges chamfered. (Door width: 600mm) Accessories 304 Grade a) SS Coated Top Rail b) 304 SS Hinges – Gravity to close<br>c) 304 SS Privacy Thumb turn c/w Occupancy Indicator 304 SS Coat Hook 304 SS Door Knob) 316 SS Adjustable Pedestal 304 SS channel )SS Coated Door Stopper channel Rubber Door Stopper Lining Screws & Wall Plugs

od188748/2019_2020 : Average Cubicles -1000mm W X 2100mm Ht : Supply and installation of Restroom cubicle system that includes intermediate panel, pilaster & door made of BWR .PLY and laminates of single colour . The solid BWR .PLYpact laminate is based on thermosetting resins, homogeneously reinforced with cellulose fibres and is manufactured as per relevant quality standards. Top surface on both sides is melamine coated which is scratch & impact resistant . Intermediate panel is one continuous panel without any joints , All intermediate panels , pilaster & doors shall be 12mm thick with edges chamfered. (Door width: 600mm) Accessories 304 Grade a) SS Coated Top Rail<br>b) 304 SS Hinges – Gravity to close<br>c) 304 SS Privacy Thumb turn c/w Occupancy Indicator<br>d)304 SS Coat Hook<br>e) 304 SS Door Knob<br>f) 316 SS Adjustable Pedestal<br>g) 304 SS “U” channel <br>h)SS Coated Door Stopper channel <br>i) Rubber Door Stopper Lining<br>j) Screws & Wall Plugs

od188754/2019_2020 : Providing and fixing of Luxalon Louver system powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make sub frame work for matallic aluminum louvers works with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size as complete colour and shade as per approved architectural drawings and direction of the Engineer-incharge

False Ceiling Works

26.22.1 : Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 8 mm thick tegular edged light weight calcium silicate false ceiling tiles.

od188680/2019_2020 : ARMSTRONG FALSE CEILING: Supplying in true horizontal level false ceiling imported 15 mm tk Plain grid using hot dipped galvanised steel sections, exposed surface chemically cleaned capping with baked enamelled white colour tee caps, to be suspended from the ceiling by 3mm gi wire at with J bolt 1200 c/c, not more than 150mm from wall angle for main tee and 1200mm cross tees shall be spaced at 600mm c/c to form 600 x 600mm modules. 600mm cross tees subdivide the 1200 x 600mm module. the perimeter trims shall be fixed to the walls at a maximum 450mm centres finally the boarding will be done AMF Star VT 15 (0. 6 NRC ) tile.

od188686/2019_2020 : Supplying in true horizontal level false ceiling imported 15 mm tk Plain grid using hot dipped galvanised steel sections, exposed surface chemically cleaned capping with baked enamelled white colour tee caps, to be suspended from the ceiling by 3mm gi wire at with J bolt 1200 c/c, not more than 150mm from wall angle for main tee and 1200mm cross tees shall be spaced at 600mm c/c to form 600 x 600mm modules. 600mm cross tees subdivide the 1200 x 600mm module. the perimeter trims shall be fixed to the walls at a maximum 450mm centres finally the boarding will be done AMF Thermatax Antaris 15mm Tk 0.9 NRC tile (595*595 mm ) .

26.26.1 : Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

12.45.1 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

od188699/2019_2020 : Providing and fixing Wooden Trap door in gyp ceiling areas of size 2000mm x 1500mm size. The rate shall include for providing 75mm x 75mm teak wood framework with 12mm thick BWR ply placed at bottom of the false ceiling level. The exposed surface of plywood is finished with 1.5mm thick laminate of matching colour of the false ceiling and other the other surfaces inside the frame work and plywood shall be finished with two coats of matt enamel paint over a coat of primer and putty as directed.

HVAC WORKS

od188674/2019_2020 : Supply installation testing and commissioning of 42 HP VRF Outdoor Unit:

od188681/2019_2020 : Supply installation testing and commissioning of 40HP VRF Outdoor Unit

od188687/2019_2020 : Supply installation testing and commissioning of 38 HP VRF Outdoor Unit

od188696/2019_2020 : Supply installation testing and commissioning of 32 HP VRF Outdoor Unit

od188700/2019_2020 : Supply installation testing and commissioning of 30 HP VRF Outdoor Unit

od188705/2019_2020 : Supply installation testing and commissioning of 8.0 TR High Static Concealed split indoor unit: Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit

od188712/2019_2020 : Supply installation testing and commissioning of 6.0 TR High Static Concealed split indoor unit: Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188717/2019_2020 : Supply installation testing and commissioning of 5.0 TR High Static Concealed split indoor unit- Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188721/2019_2020 : Supply installation testing and commissioning of 4.0 TR High Static Concealed split indoor unit - Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188726/2019_2020 : Supply installation testing and commissioning of 3.0 TR High Static Concealed split indoor unit-Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188730/2019_2020 : Supply installation testing and commissioning of 2.5TR High Static Concealed split indoor unit-Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit

od188735/2019_2020 : Supply installation testing and commissioning of 2.0TR High Static Concealed split indoor unit-Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188740/2019_2020 : Supply installation testing and commissioning of 1.0TR High Static Concealed split indoor unit- Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit

od188744/2019_2020 : Supply installation testing and commissioning of 0.8TR High Static Concealed split indoor unit- Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188749/2019_2020 : Supply installation testing and commissioning of 2.0 TR 4 way cassette- Complete with low-noise centrifugal fan, cooling coil, filter, flexible connection, insulated drain pan, drain pump with automatic operation, protective devices for electrical and electronics components and electronic expansion valve with local wired control unit.

od188755/2019_2020 : Supply, erection, testing &amp; commissioning of central measurement system for measuring running hours, power consumption, etc. of all indoor and outdoor units and generating suitable reports

od188760/2019_2020 : Central Remote Controller: Supply, erection, testing and commissioning of central remote controller with communication facility for integration with Honeywell proprietary protocol as existing

od188764/2019_2020 : Supply installation testing and commissioning of AIR HANDLING UNITS WITH AHU KIT: 14 TR/5600 CFM AHU with AHU kit (Ceiling suspended)

od188770/2019_2020 :Supply installation testing and commissioning of AIR HANDLING UNITS WITH AHU KIT: 8 TR/3600 CFM AHU with AHU kit (Ceiling suspended)

od188780/2019_2020 : 6.35 mm with 13 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188784/2019_2020 : 9.52 mm with 13mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188790/2019_2020 : 12.7 mm with 13 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188795/2019_2020 : 15.9 mm with 13 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188798/2019_2020 : 19.1 mm with 13 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188802/2019_2020 : 22.4 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188806/2019_2020 : 25.4 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188808/2019_2020 : 28.6 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188810/2019_2020 : 34.9 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188812/2019_2020 : 41.3 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188814/2019_2020 : 44.5 mm with 19 mm thick insulation :Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction with Y-Joints, including elbows and other necessary fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade with mechanical protection coating/layer, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. All pipes used shall be recommended/approved one by VRF/VRV system manufacturer

od188817/2019_2020 : 1.0 TR WITH 25M REF PIPING :SITC of new factory supplied air cooled wall mounted split modular type air-conditioning system complete with indoor &amp; outdoor units with individual cordless controller as per the following capacities of the ODU and IDU. (3 star rated)

od188818/2019_2020 : 80mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188820/2019_2020 : 65mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188822/2019_2020 : 50mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188824/2019_2020 : 40mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188825/2019_2020 : 32mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188827/2019_2020 : 20mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188829/2019_2020 : 25mm dia : Supply, testing and commissioning of condensate drain PVC piping as per BIS 4985 (10kg/cm2) with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell nitrile rubber insulation, fire retardant grade as per the drawing and relevant standards.

od188832/2019_2020 : 20 GAUGE : Supply, installation, testing and balancing of factory fabricated rectangular GSS ducting of following thickness including necessary supports, hangers, nut bolts, gaskets, splitter dampers, vanes, canvas connections etc. complete as per SMACNA/ IS 655 standards. Rates shall be inclusive of breaking and making good of wall openings required for the ducts.

od188833/2019_2020 : 22 GAUGE : Supply, installation, testing and balancing of factory fabricated rectangular GSS ducting of following thickness including necessary supports, hangers, nut bolts, gaskets, splitter dampers, vanes, canvas connections etc. complete as per SMACNA/ IS 655 standards. Rates shall be inclusive of breaking and making good of wall openings required for the ducts.

od188834/2019_2020 : 24 GAUGE : Supply, installation, testing and balancing of factory fabricated rectangular GSS ducting of following thickness including necessary supports, hangers, nut bolts, gaskets, splitter dampers, vanes, canvas connections etc. complete as per SMACNA/ IS 655 standards. Rates shall be inclusive of breaking and making good of wall openings required for the ducts.

od188835/2019_2020 : Supply, installation and testing of acoustic lining with 10 mm thick open cell nitrile foam on the inner side of ducting including providing, fixing and finishing the same as per specifications for ducts as required density of material shall be 140-180 kg/cubm

od188836/2019_2020 : 13mm Thick Nitrile Rubber :Supply, installation and testing of thermal insulation of ducts using closed cell Nitrile Rubber insulation with recommended adhesives and sealed with black adhesive tape and density of material shall be 40-60 kg/cubm

od188837/2019_2020 : 9mm Thick Nitrile Rubber :Supply, installation and testing of thermal insulation of ducts using closed cell Nitrile Rubber insulation with recommended adhesives and sealed with black adhesive tape and density of material shall be 40-60 kg/cubm

od188839/2019_2020 : Powder coated extruded aluminium 4 way removable core type Return air Diffusers

od188842/2019_2020 : Powder coated extruded aluminium 4 way removable core type Supply air Diffusers complete with volume control damper

od188844/2019_2020 : Powder coated extruded Aluminium Return air Grilles with horizontal fixed bars and end flanges

od188845/2019_2020 : Powder coated extruded Aluminium Supply air Grilles with horizontal fixed bars and end flanges complete with volume control damper

od188846/2019_2020 : 375X375 PLENUM BOX : Supply and installation of GI factory-fabricated plenum boxes with acoustic insulation out of 18mm thick open cell noise absorbing material with necessary angle frame, support etc. Following Sizes

od188848/2019_2020 : 300X300 PLENUM BOX : Supply and installation of GI factory-fabricated plenum boxes with acoustic insulation out of 18mm thick open cell noise absorbing material with necessary angle frame, support etc. Following Sizes

od188849/2019_2020 : FIRE DAPMPEr: Supplying, fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event. of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Factory made Fire dampers with 1.6mm GSS sleeves with minimum 90 min fire rating complete with accessories.

od188850/2019_2020 : SITC of ACTUATOR

od188851/2019_2020 : Supply, installation, testing and balancing of box type GI volume control damper complete as per specifications

od188852/2019_2020 : Supply, installation, testing and commissioning of powder coated extruded aluminium fresh air louvers with aluminium bird screen and MS volume control damper as per drawing and relevant standards

od188853/2019_2020 : 300mm Dia : Supply & installation of Flexible ductwork of two layer aluminized polyester inner core, surrounded by 25 mm thickness of 24 Kg/M3 density fibreglass, all wrapped in a reinforced multilayer aluminium polyester outer jacket.

od188854/2019_2020 : 200mm Dia : Supply & installation of Flexible ductwork of two layer aluminized polyester inner core, surrounded by 25 mm thickness of 24 Kg/M3 density fibreglass, all wrapped in a reinforced multilayer aluminium polyester outer jacket.

od188855/2019_2020 : 150mm Dia : Supply & installation of Flexible ductwork of two layer aluminized polyester inner core, surrounded by 25 mm thickness of 24 Kg/M3 density fibreglass, all wrapped in a reinforced multilayer aluminium polyester outer jacket.

od188856/2019_2020 : 2100 CFM @ 250Pa External static pressure: SITC of INLINE fans complete with all accessories including supports/hangers , gravity louvers, canvas connections, etc as per specifications &amp; drawings

od188857/2019_2020 : 200MM DIA: Supply, installation, testing and commissioning of powder coated extruded aluminium Extract air disc valves with MS volume control damper as per drawing and relevant standards.

od188858/2019_2020 : 150MM DIA: Supply, installation, testing and commissioning of powder coated extruded aluminium Extract air disc valves with MS volume control damper as per drawing and relevant standards.

od188859/2019_2020 : 100MM DIA: Supply, installation, testing and commissioning of powder coated extruded aluminium Extract air disc valves with MS volume control damper as per drawing and relevant standards.

od188860/2019_2020 : 1 YEAR: Annual Maintenance contract rates for VRF units after Defects liability period including material and labour parts

od188861/2019_2020 : 2ND YEAR:Annual Maintenance contract rates for VRF units including material and labour parts

od188863/2019_2020 : 3RD YEAR:Annual Maintenance contract rates for VRF units including material and labour parts

od188865/2019_2020 : 4TH YEAR Annual Maintenance contract rates for VRF units including material and labour parts

od188867/2019_2020 : 5TH YEAR Annual Maintenance contract rates for VRF units including material and labour parts

PLUMBING @ SANITORY WORKS

od188675/2019_2020 : Supplying and fixing white vitreous china wall-hung type water closet (European type) with seat and lid, 6/9 litre dual flush concealed flush tank and CP flush plate, flush bend with fittings &amp; CI brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

od188682/2019_2020 : Supplying and fixing health faucet with one meter flexible tube and angle valve including cutting and making good the wall.

od188688/2019_2020 : Supplying and fixing white glazed earthenware counter type wash basin, with 15mm dia brass CP basin pillar tap, 32mm dia. brass CP waste coupling, 32 mm dia brass CP bottle trap with extension pipe, stainless steel screws, 1no. 15mm brass CP angle valve with 450mm long metallic flexible tube, brass CP wall flanges, 40 X 32mm PVC reducer to connect the extension pipe from bottle to the PVC waste pipe, all of approved make etc., complete including cutting and making good the walls.

od188693/2019_2020 : Supplying and fixing of white glazed large flat back urinal of size 430mm X 230mm X 350mm or nearest size with 40mm dia CP waste coupling with dome type grating, 40mm dia CP bottle trap with extension pipe, urinal spreader, concealed urinal flush, sensor plate, SS bolts and nuts to fix the urinal with all hangers and brackets complete with wall flanges including cutting and making good the walls and floors

od188697/2019_2020 : Supply and fixing of 15mm angle valves for provision for water supply for water purifier, etc.

od188701/2019_2020 : Supply and fixing of Robe Hook complete etc and fixing to wooden plugs with CP brass screws

od188706/2019_2020 : Supply and fixing in position of Toilet Roll Holder complete as required

od188713/2019_2020 : Supply and fixing of Towel rail and fixing to wooden plugs with CP brass screws

od188722/2019_2020 : Supply and fixing Liquid Soap Dispenser with concealed fitting arrangements

od188723/2019_2020 : Supply and fixing in position of bib tap with hose connector complete as required

od188731/2019_2020 : 50mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188736/2019_2020 : 40 mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188741/2019_2020 : 32 mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188745/2019_2020 : 25 mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188750/2019_2020 : 20 mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188756/2019_2020 : 15 mm dia: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes running exposed through ducts, distribution risers, ring main etc joining specials such as tees, bends, elbows etc. including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections and fixing pipes with clamps on rails suitably complete.

od188761/2019_2020 : 25mm dia internal Piping: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes (internal wall concealed), joining specials such as tees, bends, elbows, check nuts, etc. with clamps including cutting and making good the walls complete..

od188765/2019_2020 : 15mm dia internal Piping: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes (internal wall concealed), joining specials such as tees, bends, elbows, check nuts, etc. with clamps including cutting and making good the walls complete..

od188771/2019_2020 : 20mm dia internal Piping: Supply and laying with solvent cement pasted ASTM D-1785 uPVC pipes (internal wall concealed), joining specials such as tees, bends, elbows, check nuts, etc. with clamps including cutting and making good the walls complete..

18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

od188791/2019_2020 : 40mm dia: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188794/2019_2020 : 50mm dia: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188799/2019_2020 : 160mm dia: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188803/2019_2020 : 110mm dia: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188805/2019_2020 : 75mm dia: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188809/2019_2020 : 110 mm uPVC class A: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188811/2019_2020 : 75 mm uPVC class A: Supplying, laying and joining with solvent cement pasted uPVC pipes including joining specials such as tees, bends, elbows etc. with clamps including cutting masonry or concrete floors, slabs, walls etc, wherever necessary for taking connections, embedded in cement mortar complete.uPVC drainage system with pipes conforming to pressure class 6 kg/cm&sup2; as per IS 4985:2000

od188813/2019_2020 : 160 mm uPVC: Supply, installation, testing and commissioning of 3 layered poly propylene pipes of sound level 13dB @ 2 l/s in accordance with EN-14366 suitable for the application of ceiling suspended non pressurised drainage pipes in occupied spaces with push fittings and other accessories like supports, hangers, brackets etc. in accordance with drawings and relevant standards.

od188815/2019_2020 : 110 mm uPVC: Supply, installation, testing and commissioning of 3 layered poly propylene pipes of sound level 13dB @ 2 l/s in accordance with EN-14366 suitable for the application of ceiling suspended non pressurised drainage pipes in occupied spaces with push fittings and other accessories like supports, hangers, brackets etc. in accordance with drawings and relevant standards.

od188816/2019_2020 : 75 mm uPVC: Supply, installation, testing and commissioning of 3 layered poly propylene pipes of sound level 13dB @ 2 l/s in accordance with EN-14366 suitable for the application of ceiling suspended non pressurised drainage pipes in occupied spaces with push fittings and other accessories like supports, hangers, brackets etc. in accordance with drawings and relevant standards.

od188819/2019_2020 : 110 mm dia pipe below ground: Supplying, laying and joining uPVC pipes including joining specials such as tees, bends, elbows etc. in trenches up to a depth of 1.5 m joining with solvent cement , filling in water and testing the line to the required pressure including earth work excavation in all classes of soil except hard rock, fencing the sides of trenches, keeping danger lights during night , watching, bailing out water from trenches if necessary, refilling trenches , consolidating in 20 cms layers, watering, ramming and removing and depositing the surplus earth within a distance of 50 m.SWR Drainage system with Class B uPVC pipes as per IS 13592-1992 (waste, soil, rain water pipes ,vent pipes landscape drains etc)

od188821/2019_2020 : 160 mm dia pipe below ground: Supplying, laying and joining uPVC pipes including joining specials such as tees, bends, elbows etc. in trenches up to a depth of 1.5 m joining with solvent cement , filling in water and testing the line to the required pressure including earth work excavation in all classes of soil except hard rock, fencing the sides of trenches, keeping danger lights during night , watching, bailing out water from trenches if necessary, refilling trenches , consolidating in 20 cms layers, watering, ramming and removing and depositing the surplus earth within a distance of 50 m.SWR Drainage system with Class B uPVC pipes as per IS 13592-1992 (waste, soil, rain water pipes ,vent pipes landscape drains etc)

od188823/2019_2020 : 75 mm dia pipe below ground: Supplying, laying and joining uPVC pipes including joining specials such as tees, bends, elbows etc. in trenches up to a depth of 1.5 m joining with solvent cement , filling in water and testing the line to the required pressure including earth work excavation in all classes of soil except hard rock, fencing the sides of trenches, keeping danger lights during night , watching, bailing out water from trenches if necessary, refilling trenches , consolidating in 20 cms layers, watering, ramming and removing and depositing the surplus earth within a distance of 50 m.SWR Drainage system with Class B uPVC pipes as per IS 13592-1992 (waste, soil, rain water pipes ,vent pipes landscape drains etc)

od188826/2019_2020 : 160mm clean out: Supply and Installation of sanitary drainage fixings and accessories and making good the wall/ slab all in accordance with the drawings and specification.

od188828/2019_2020 : 110mm clean out: Supply and Installation of sanitary drainage fixings and accessories and making good the wall/ slab all in accordance with the drawings and specification.

od188830/2019_2020 : Floor Cleanout: Supply and Installation of sanitary drainage fixings and accessories and making good the wall/ slab all in accordance with the drawings and specification.

od188831/2019_2020 : 110mm floor trap: Supply and Installation of sanitary drainage fixings and accessories and making good the wall/ slab all in accordance with the drawings and specification.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.4.1.1 : Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FIRE PROTECTION WORKS

od188676/2019_2020 : AUTHORITY APPROVALS AND COORDINATION: Preparation of all drawings, submitting and getting approval from fire department, submitting of completion certificates and arranging inspection, getting sanction, etc. for commissioning of the whole installation in the premises.(All statutory payments will be reimbursed with original receipts.)

od188677/2019_2020 : DISMANTLING OF EXISTING FIRE SYSTEMS: Dismantling G.I/MS. pipes manually/ by mechanical means and including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

od188683/2019_2020 : 25mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188689/2019_2020 : 32mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188694/2019_2020 : 40mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188702/2019_2020 : 50mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188707/2019_2020 : 65mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188708/2019_2020 : 80mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188714/2019_2020 : 100mmdia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188718/2019_2020 : 150mm dia: Supply, installation, testing and commissioning of fire fighting system pipe work for Fire Brigade Inlet, Wet Risers , sprinklers etc with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. Supports for the underground pipes with anchor blocks, angular supports for above ground pipes not less than every three meter intervals or as required by the consultant/client. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188727/2019_2020 : Supply, installation, testing and commissioning of 50mm dia sprinkler drain pipe work for sprinkler system with MS C class pipe as per IS:1239 with all fittings like bends, tees, flanges, nuts bolts, washers etc. The welding should be as per the functional requirement of the System, and the welded pipes should withstand 20Kg/cm.sq for 24 hours. The welding accessories should be in accordance with the IS specifications.&lt;br&gt;The above ground pipe are to be applied with two coats of zinchromate primer and two coats of enamel paint of approved colour.

od188732/2019_2020 : Supply, erection, testing &amp; commissioning of Pressure Gauges with isolation valve and accessories with flanges, all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards

od188737/2019_2020 : Supply, erection, testing &amp; commissioning of single headed gunmetal oblique type landing/hydrant valve (as per IS:5290) with 63mm outlet gunmetal instantaneous male/female coupling with rubber/Plastic cap duly binded with stainless steel wire and 15m long flexible hose (as per IS:636-type A) etc. complete as specifie

od188738/2019_2020 : ZONE CONTROL VALVES AND ACCESSORIESSupply, erection, testing &amp; commissioning Zone Control Valves, Flow switch, isolation valve, drain valve assembly, with accessories including all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards150mm dia zone control valve

od188742/2019_2020 : Supply, erection, testing &amp; commissioning of Fire hose real cabinet (16Guage fire hose cabinet 750x750x300mm with double door and in kept of two nos with fully powder coated.) including automatic swinging type 25mm (nominal internal) dia &amp; 30m long first aid flexible hose reel with all necessary fittings &amp; ball valve (IS:12585 &amp; IS:884), standard SS branch pipe with nozzle of 20mm (IS:903) suitable to fit with standard instantaneous type 63mm coupling, 4Kg dry powder fire extinguisher and 4.5 Kg CO2 extinguisher all as specified and as shown on drawings and complying to authority regulations and relevant standards (Refer FHRC)

od188746/2019_2020 : Supply, erection, testing &amp; commissioning of (Pendant Type) sprinkler heads with all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards

od188751/2019_2020 : Supply, erection, testing &amp; commissioning of Up-Right type sprinkler heads with all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards

od188757/2019_2020 : Supply, Installation, Testing and Commissioning of 1000mm Length Sprinkler Flexible type of approved make.

od188766/2019_2020 : Supply, erection, testing &amp; commissioning of Fire extinguishers &amp; Accessories all in accordance with the drawings and specifications. 4 kg ABC Dry chemical powder extinguisher

od188767/2019_2020 : Supply, erection, testing &amp; commissioning of Fire extinguishers &amp; Accessories all in accordance with the drawings and specifications.CO2 fire extinguisher 4.5kg

od188772/2019_2020 : FIRE ALARM PANEL: Supply, Installation, Testing and Commissioning of Analogue Addressable Fire alarm control panel capable of handling more then 250 devices / detectors per loop. The panel and devices shall be fully-compatible with the existing system and shall be integrated with it. The panel shall have a minimum of four loops Transformer rooms, Warehouse, Dormitory and normal working environments.

od188775/2019_2020 : MULTI SENSORS: Supply, Installation, Testing and Commissioning of Intelligent Addresable Multi Sensor with optical smoke element and thermal element. The detector shall have facility to mount in different comprehensive environment like Hostile environment, Parking Garage, HVAC Ducts, Precious storage, Transformer rooms, Warehouse, Dormitory and normal working environments.

od188778/2019_2020 : HEAT SENSORS: Supply, Installation, Testing and Commissioning of Intelligent Addressable Heat Detector with base. The detector shall be suitable for both rate of rise and fixed temperature.

od188782/2019_2020 : SOUNDER: Supply, Installation, Testing and Commissioning of addressable sounder with built in module at different locations complete with all fixing accessories.

od188786/2019_2020 : MANUAL PULL STATION: Supply, Installation, Testing and Commissioning of analogue addressable type Manual pull station at indicated locations with necessary termination as per acceptable specifications and full ready for operation.

od188793/2019_2020 : MONITOR MODULE: Supply, Installation, Testing and Commissioning of Intelligent Addressable Monitor module for connecting different input of Fire alarm panel like flow switch etc..

od188800/2019_2020 : SHORT CIRCUIT ISOLATOR MODULE: Supply, Installation, Testing and Commissioning of Short Circuit Isolator Module for isolating the affected segment of the circuit, allowing the remaining devices to continue operation.

od188801/2019_2020 : FIRE SURVIVAL CABLE : Supply, Installation, Testing and Commissioning of Fire Survival Cables conforming to BS: 7846 armoured 2 core x 1.5 sqmm.

ELECTRICAL WORKS

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.2 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

od188777/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)4 way Double door, Vertical , Three Phase

od188781/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)12 way (4 + 36), Double door, Three Phase

od188785/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)8 way (4 + 24), Double door, Three Phase

od188787/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)6 way (4 + 18), Double door, Three Phase

od188792/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)4 way (4 + 12), Double door,Three Phase

od188797/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)2 + 12 way, Double door, Single Phase

od188804/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)2 + 8 way, Double door, Single Phase

od188807/2019_2020 : Supplying and fixing following way distribution boards of steel sheet on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)2 + 4 way, Double door, Single Phase

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.2.18 : Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.400 Amp, 50 KA, 4 pole

3.2.7 : Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required.400 amps TPN

4.6.4 : Supplying and installing following size of perforated Hot dip galvanised Iron cable trays(galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with all accessories including cross, reducer, bend,G.I. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.6.6 : Supplying and installing following size of perforated Hot dip galvanised Iron cable trays(galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with all accessories including cross, reducer, bend,G.I. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X50 mm depth X 2.0 mm thickness

4.6.7 : Supplying and installing following size of perforated Hot dip galvanised Iron cable trays(galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with all accessories including cross, reducer, bend,G.I. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

od188841/2019_2020 : Supplying and laying 25 mm X 3 mm copper strip as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt &amp; spring washer spaced at 50mm)

od188843/2019_2020 : Providing and fixing 10 SWG dia copper. wire on surface or in recess for loop earthing as required.

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.31 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

od188862/2019_2020 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. SMDB-UB-AC, 400A 4P Automatic Transfer Switch with Controller Unit - 1No, 400A, 4P, Isolator - 1No, Indication Lamp Set - 2Nos, 125A, 35kA, 4P MCCB - 12Nos, 3Phase LED kWh MFM with RS-485 for communication CL-0.5, Panel Mount - 12Nos

od188864/2019_2020 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. SMDB-UB-1/2, Incomer, 400A, 4P, Isolator - 1No, Indication Lamp Set, Bus bar: 400A, 4P, Al (Electrical Grade), 35kA, Outgoing, 250A, 35kA, 4P MCCB - 4Nos

od188866/2019_2020 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. MP-TYP, Incomer, 250A, 4P, Isolator - 1No, Indication Lamp Set - 1No, Bus bar: 250A, 4P, Al (Electrical Grade), 25kA, Outgoing, 63A/40A, 4P, 25kA, MCB - 8Nos, 3Phase LED kWh MFM with RS-485 for communication CL-0.5, Panel Mount - 8Nos (Wiring within the panel board for communication network of the MFMs to be part of this scope and terminals to be available in the panel for connection of cable from BMS. The MFMs and related cabling shall be fully compatible with the BMS for software integration).

od188868/2019_2020 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. SMDB-OF-TYP, Incomer, 63A, 4 pole On-Load Change Over Switch - 1No,63A, 4P, MCB Isolator - 1No, Indication Lamp Set - 2Nos, 3Phase Digital V,A,F, kW Meter CL-0.5, Panel Mount - 1Nos, Bus bar: 100A, 4P, Al (Electrical Grade), 25kA, Outgoing, 32/40A, 4P, 16kA, MCB - 3Nos

od188869/2019_2020 : Supply, installation, testing and commissioning of 40A, 4P, Isolator in sheet steel enclosure for equipment power supply.

od188870/2019_2020 : Supply, installation, testing and commissioning of 125A, 4P, Isolator in sheet steel enclosure for equipment power supply

od188871/2019_2020 : Supply, installation, testing and commissioning of UPS with 20min backup with SMF battery of 2yr warranty. The system shall be true online, double conversion technology with input pf &gt;0.98, input current THD &lt;10% and 100% generator compatabile. The system shall comply to IEC /EN 62040-1 and relevant IS standard. 10kVA 3ph input / 3ph output

od188872/2019_2020 : Supply, installation, testing and commissioning of 90mm width x 35mm height PVC underfloor trunking including suitable connectors and clamps

od188873/2019_2020 : Supply, installation, testing and commissioning of under floor pregalvanized junction box with knock outs three PVC duct entries in all the four sides. The box shall have a powder coated trap and frame (2+3mm) suitable for tile flooring with 10mm recess. Dimensions: 357x357x55mm

od188874/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required.Energy efficient recessed mounted LED light fittings suitable for 600x600mm grid-type suspended ceilings. Lumen output: 3300lm, Light colour: Neutral White - 5000K, Power consumption: 36W, Driver: Constant current driver, Optics: High efficiency powder coated reflectors and high transitivity opal diffuser cover, Material: Powder coated CRCA housing and CRCA front frame, CRI: &gt;80

od188875/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. Low glare, hight effeciency recessed mounted LED down light - circular profile. Lumen output: 850lm, Light colour: Neutral White - 5000K, Power consumption: 15W, Driver: Non-integral constant current electronic driver with a gear tray, Optics: High efficiency optics with high reflective diffuser providing efficient glare free lighting

od188876/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. Low glare, hight effeciency recessed mounted LED down light - square profile. Lumen output: 850lm, Light colour: Neutral White - 5000K, Power consumption: 15W, Driver: Non-integral constant current electronic driver with a gear tray, Optics: High efficiency optics with high reflective diffuser providing efficient glare free lighting

od188877/2019_2020 : Pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. Low glare, hight effeciency recessed mounted LED down light - circular profile. Lumen output: 600lm, Light colour: Neutral White - 5000K, Power consumption: 10W

od188878/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. LED spot light - circular profile,Power consumption: 6W

od188879/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. 1.2m long LED Batten light fitting. Lumen output: 3600lm, Light colour: 4000K, Power consumption: 20W, CRI: &gt;80, Optics: Frosted diffuser

od188880/2019_2020 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. LED bulkhead light fitting, Lumen output: 600lm

1.53.1 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

od188881/2019_2020 : Supply and commissioning of Cat 6 RJ 45 outlets to be fixed on existing modular face plates and including termination of Cat 6 cables on the outlets

od188882/2019_2020 : Supply, installation, termination, testing and commissioning of 24port fully loaded patch panel

od188883/2019_2020 : Supply and installation of 20U Rack with cable manager and all other accessories

od188884/2019_2020 : Supply, laying, testing and commissioning of Fiber Optic Cable 6 core SM Indoor / Outdoor Cable including splicing and termination at both end

od188885/2019_2020 : Supply, installation, testing and commissioning of LIU 06 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od188886/2019_2020 : Supply, installation, testing and commissioning of LIU 24 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od188887/2019_2020 : Supply, installation, testing and commissioning of 1x6 SC Adaptor Module Panel - Simplex and including all accessories like pigtails, sleeves, etc.

od188888/2019_2020 : Supply, installation, testing and commissioning of 1x24 SC Adaptor Module Panel - Simplex and including all accessories like pigtails, sleeves, etc.

od188889/2019_2020 : Supply, installation, testing and commissioning of End-to-end structured cabling system for voice / data distribution . 10pair Krone module fixed in box.

od188890/2019_2020 : Supplying and installation of ELV and Building Management System Devices and connecting to / integrating with existing ELV and BMS systems. BMS - Software Update

od188891/2019_2020 : Supply, installation, testing and commissioning of Interface for integrating Third Party Systems via BACNet / Honewell properietary / RS485 Interface - Integration of VRF System

od188892/2019_2020 : Supply, installation, testing and commissioning of Interface for integrating Third Party Systems via BACNet / Modbus / RS485 Interface - Integration of Energy Meters

od188893/2019_2020 : Supply, installation, testing and commissioning of Interface for integrating Third Party Systems via BACNet / Honewell properietary / RS485 Interface - BTU Meters

od188894/2019_2020 : Supply, installation, testing and commissioning of 50mm Ultrasonic BTU Meters to be installed on existing chilled water lines

od188895/2019_2020 : Supply, installation, testing and commissioning of 40mm Ultrasonic BTU Meters to be installed on existing chilled water lines

od188896/2019_2020 : Supply, installation, testing and commissioning of 32mm Ultrasonic BTU Meters to be installed on existing chilled water lines

od188897/2019_2020 : Supply, installation, testing and commissioning of LBMS - Direct Digital Controllers: BACnet / LON-ighting Control - Upper Basement Floor

od188898/2019_2020 : Supply, installation, testing and commissioning of BMS - Field Devices-Lux Sensor

od188899/2019_2020 : Supply, installation, testing and commissioning of BMS - Field Devices-Motion Sensor

od188900/2019_2020 : Supply, laying, testing and commissioning of Armoured FRLS 2 core 1 sqmm Shielded ATC Cable

od188901/2019_2020 : Supply, laying, testing and commissioning of Armoured FRLS 4 core 1 sqmm Shielded ATC Cable

od188902/2019_2020 : Supply, laying, testing and commissioning of Armoured FRLS 8 core 1 sqmm shielded ATC Cable

od188903/2019_2020 : Supply, laying, testing and commissioning of Armoured FRLS Communication Cable - CAT6 Cable

od188904/2019_2020 : Supply, laying, testing and commissioning of Armoured FRLS 2 core 1.5sqmm Shieled ATC Cable

od188905/2019_2020 : Supply, laying, testing and commissioning of BMS - Cabling -Armoured FRLS 3 core 1.5sqmm Power Cable

od188906/2019_2020 : Providing CCTV cameras and connecting to existing CCTV system. Indoor UL Listed, 2.7-12mm motorized vari-focal lens of 2MP, H.264 compression, 120db WDR, ONVIF2.0, IR day and night Dome Color Camera with POE

od188907/2019_2020 : Supply, installation, testing and commissioning of High Fidility Ceiling Speakers with matching transformers, back boxes and accessories

od188908/2019_2020 : Supply, installation, testing and commissioning of High Fidility Wall-mounted Speakers with matching transformers, back boxes and accessories

od188909/2019_2020 : Supply, laying, testing and commissioning of Speaker Circuit wiring - 2core 24/0.2mm ATC twin twisted shielded, FRLS type, armoured cable (Green colour)

od188910/2019_2020 : Supply, installation, testing and commissioning of Ceiling mounted Projector of min. 3300 lumens, SVGA resolution, Contrast ratio of 15,000:1, Horizontal keystone slider, 10,000 hours lamp life in eco-mode or better, Analog Input: D-Sub 15pin/Composite: RCA x 1, USB interfaces, HDMI Interface, Audio Input: 2 RCA, IEEE 802.11b/g/n (2.4GHz), Sound Output: 2W Mono or better

od188911/2019_2020 :Supply, installation, testing and commissioning of High Fidelity Ceiling Speakers with matching transformers, Back boxes, and accessories

od188912/2019_2020 : Supply, installation, testing and commissioning of Plena Mixing Amplifier - 240W

od188913/2019_2020 : Supply, installation, testing and commissioning of Music source with USB and FM Tuner

od188914/2019_2020 : Supply, laying, testing and commissioning of Speaker Circuit wiring - 2 core twisted 48/0.2 Multistrand speaker cable

od188915/2019_2020 : Supply, installation, testing and commissioning of Cable cubby with HDMI and Audio ports and HDMI cable to projector and audio cable to amplifier

od188916/2019_2020 : Obtaining approval from Statutory Authorities, Preparation of statutory drawings, completion Report, Arranging for Inspection, attending defects report and obtaining safety certificate from Safety Authorities for commissioning of the electrical system.(including all required statutory Norms ) ( All statutory payments will be reimbursed with original receipts) &lt;br&gt;

Supply of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1kV grade of following size on cable tray as required.

4 x 10mm2 AYFY AL Cable

4x 16mm2 AYFY AL Cable

4 x 25mm2 AYFY AL Cable

3.5 x 35mm2 AYFY AL Cable

3.5 x50mm2 AYFY AL Cable

3.5 x70mm2 AYFY AL Cable

3.5 x95mm2 AYFY AL Cable

3.5 x120mm2 AYFY AL Cable

3.5 x150mm2 AYFY AL Cable

3.5 x185mm2 AYFY AL Cable

3.5 x240mm2 AYFY AL Cable

3.5 x400mm2 AYFY AL Cable

Stencil Engineering Pvt Ltd

Keechery Engg Co

Bidder Name

Macro Enterprises

Keechery Engg Co

Stencil Engineering Pvt Ltd